From: Anson Huang <[email protected]>
i.MX8MM has a thermal monitor unit (TMU) inside, it ONLY has one sensor
for CPU, add support for temperature reading for CPU, cpu cooling is
also added.
This patch series is based on below i.MX SCU thermal patch series:
https://patchwork.kernel.org/patch/11000821/
Anson Huang (4):
dt-bindings: thermal: imx8mm-thermal: Add binding doc for i.MX8MM
thermal: imx8mm: Add support for i.MX8MM thermal monitoring unit
arm64: defconfig: Enable CONFIG_IMX8MM_THERMAL as module
arm64: dts: imx8mm: Add thermal zone support
.../devicetree/bindings/thermal/imx8mm-thermal.txt | 15 +++
arch/arm64/boot/dts/freescale/imx8mm.dtsi | 43 +++++++
arch/arm64/configs/defconfig | 1 +
drivers/thermal/Kconfig | 10 ++
drivers/thermal/Makefile | 1 +
drivers/thermal/imx8mm_thermal.c | 134 +++++++++++++++++++++
6 files changed, 204 insertions(+)
create mode 100644 Documentation/devicetree/bindings/thermal/imx8mm-thermal.txt
create mode 100644 drivers/thermal/imx8mm_thermal.c
--
2.7.4
From: Anson Huang <[email protected]>
Add thermal binding doc for Freescale's i.MX8MM Thermal Monitoring Unit.
Signed-off-by: Anson Huang <[email protected]>
---
.../devicetree/bindings/thermal/imx8mm-thermal.txt | 15 +++++++++++++++
1 file changed, 15 insertions(+)
create mode 100644 Documentation/devicetree/bindings/thermal/imx8mm-thermal.txt
diff --git a/Documentation/devicetree/bindings/thermal/imx8mm-thermal.txt b/Documentation/devicetree/bindings/thermal/imx8mm-thermal.txt
new file mode 100644
index 0000000..d09ae82
--- /dev/null
+++ b/Documentation/devicetree/bindings/thermal/imx8mm-thermal.txt
@@ -0,0 +1,15 @@
+* Thermal Monitoring Unit (TMU) on Freescale i.MX8MM SoC
+
+Required properties:
+- compatible : Must be "fsl,imx8mm-tmu".
+- reg : Address range of TMU registers.
+- clocks : TMU's clock source.
+- #thermal-sensor-cells : Should be 0. See ./thermal.txt for a description.
+
+Example:
+tmu: tmu@30260000 {
+ compatible = "fsl,imx8mm-tmu";
+ reg = <0x30260000 0x10000>;
+ clocks = <&clk IMX8MM_CLK_TMU_ROOT>;
+ #thermal-sensor-cells = <0>;
+};
--
2.7.4
From: Anson Huang <[email protected]>
Enable CONFIG_IMX8MM_THERMAL as module to support i.MX8MM
thermal driver.
Signed-off-by: Anson Huang <[email protected]>
---
arch/arm64/configs/defconfig | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 126665f..eeedd3f 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -434,6 +434,7 @@ CONFIG_CPU_THERMAL=y
CONFIG_THERMAL_EMULATION=y
CONFIG_QORIQ_THERMAL=m
CONFIG_IMX_SC_THERMAL=m
+CONFIG_IMX8MM_THERMAL=m
CONFIG_ROCKCHIP_THERMAL=m
CONFIG_RCAR_THERMAL=y
CONFIG_RCAR_GEN3_THERMAL=y
--
2.7.4
From: Anson Huang <[email protected]>
i.MX8MM has a thermal monitoring unit(TMU) inside, it ONLY has one
sensor for CPU, add support for reading immediate temperature of
this sensor.
Signed-off-by: Anson Huang <[email protected]>
---
drivers/thermal/Kconfig | 10 +++
drivers/thermal/Makefile | 1 +
drivers/thermal/imx8mm_thermal.c | 134 +++++++++++++++++++++++++++++++++++++++
3 files changed, 145 insertions(+)
create mode 100644 drivers/thermal/imx8mm_thermal.c
diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
index 454cbe5..d1663cd 100644
--- a/drivers/thermal/Kconfig
+++ b/drivers/thermal/Kconfig
@@ -244,6 +244,16 @@ config IMX_SC_THERMAL
sensor. It supports one critical trip point and one
passive trip point for each thermal sensor.
+config IMX8MM_THERMAL
+ tristate "Temperature sensor driver for Freescale i.MX8MM SoC"
+ depends on ARCH_MXC
+ depends on OF
+ help
+ Support for Thermal Monitoring Unit (TMU) found on Freescale i.MX8MM SoC.
+ It supports one critical trip point and one passive trip point. The
+ cpufreq is used as the cooling device to throttle CPUs when the passive
+ trip is crossed.
+
config MAX77620_THERMAL
tristate "Temperature sensor driver for Maxim MAX77620 PMIC"
depends on MFD_MAX77620
diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
index 717a1ba..a397d4d 100644
--- a/drivers/thermal/Makefile
+++ b/drivers/thermal/Makefile
@@ -42,6 +42,7 @@ obj-$(CONFIG_ARMADA_THERMAL) += armada_thermal.o
obj-$(CONFIG_TANGO_THERMAL) += tango_thermal.o
obj-$(CONFIG_IMX_THERMAL) += imx_thermal.o
obj-$(CONFIG_IMX_SC_THERMAL) += imx_sc_thermal.o
+obj-$(CONFIG_IMX8MM_THERMAL) += imx8mm_thermal.o
obj-$(CONFIG_MAX77620_THERMAL) += max77620_thermal.o
obj-$(CONFIG_QORIQ_THERMAL) += qoriq_thermal.o
obj-$(CONFIG_DA9062_THERMAL) += da9062-thermal.o
diff --git a/drivers/thermal/imx8mm_thermal.c b/drivers/thermal/imx8mm_thermal.c
new file mode 100644
index 0000000..04f8a8f
--- /dev/null
+++ b/drivers/thermal/imx8mm_thermal.c
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 NXP.
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/thermal.h>
+
+#include "thermal_core.h"
+
+#define TER 0x0 /* TMU enable */
+#define TRITSR 0x20 /* TMU immediate temp */
+
+#define TER_EN BIT(31)
+#define TRITSR_VAL_MASK 0xff
+
+#define TEMP_LOW_LIMIT 10
+
+struct imx8mm_tmu {
+ struct thermal_zone_device *tzd;
+ void __iomem *base;
+ struct clk *clk;
+};
+
+static int tmu_get_temp(void *data, int *temp)
+{
+ struct imx8mm_tmu *tmu = data;
+ u32 val;
+
+ /* the temp sensor need about 1ms to finish the measurement */
+ usleep_range(1000, 2000);
+
+ val = readl_relaxed(tmu->base + TRITSR) & TRITSR_VAL_MASK;
+ if (val < TEMP_LOW_LIMIT)
+ return -EAGAIN;
+
+ *temp = val * 1000;
+
+ return 0;
+}
+
+static struct thermal_zone_of_device_ops tmu_tz_ops = {
+ .get_temp = tmu_get_temp,
+};
+
+static int imx8mm_tmu_probe(struct platform_device *pdev)
+{
+ struct imx8mm_tmu *tmu;
+ u32 val;
+ int ret;
+
+ tmu = devm_kzalloc(&pdev->dev, sizeof(struct imx8mm_tmu), GFP_KERNEL);
+ if (!tmu)
+ return -ENOMEM;
+
+ tmu->base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(tmu->base))
+ return PTR_ERR(tmu->base);
+
+ tmu->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(tmu->clk)) {
+ ret = PTR_ERR(tmu->clk);
+ if (ret != -EPROBE_DEFER)
+ dev_err(&pdev->dev,
+ "failed to get tmu clock: %d\n", ret);
+ return ret;
+ }
+
+ ret = clk_prepare_enable(tmu->clk);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to enable tmu clock: %d\n", ret);
+ return ret;
+ }
+
+ tmu->tzd = devm_thermal_zone_of_sensor_register(&pdev->dev, 0,
+ tmu, &tmu_tz_ops);
+ if (IS_ERR(tmu->tzd)) {
+ dev_err(&pdev->dev,
+ "failed to register thermal zone sensor: %d\n", ret);
+ return PTR_ERR(tmu->tzd);
+ }
+
+ platform_set_drvdata(pdev, tmu);
+
+ /* enable the monitor */
+ val = readl_relaxed(tmu->base + TER);
+ val |= TER_EN;
+ writel_relaxed(val, tmu->base + TER);
+
+ return 0;
+}
+
+static int imx8mm_tmu_remove(struct platform_device *pdev)
+{
+ struct imx8mm_tmu *tmu = platform_get_drvdata(pdev);
+ u32 val;
+
+ /* disable TMU */
+ val = readl_relaxed(tmu->base + TER);
+ val &= ~TER_EN;
+ writel_relaxed(val, tmu->base + TER);
+
+ clk_disable_unprepare(tmu->clk);
+ platform_set_drvdata(pdev, NULL);
+
+ return 0;
+}
+
+static const struct of_device_id imx8mm_tmu_table[] = {
+ { .compatible = "fsl,imx8mm-tmu", },
+ { },
+};
+
+static struct platform_driver imx8mm_tmu = {
+ .driver = {
+ .name = "i.mx8mm_thermal",
+ .of_match_table = imx8mm_tmu_table,
+ },
+ .probe = imx8mm_tmu_probe,
+ .remove = imx8mm_tmu_remove,
+};
+module_platform_driver(imx8mm_tmu);
+
+MODULE_AUTHOR("Anson Huang <[email protected]>");
+MODULE_DESCRIPTION("i.MX8MM Thermal Monitor Unit driver");
+MODULE_LICENSE("GPL v2");
--
2.7.4
From: Anson Huang <[email protected]>
Add thermal zone and tmu node to support i.MX8MM thermal
driver, ONLY cpu thermal zone is supported, and cpu cooling
is also added.
Signed-off-by: Anson Huang <[email protected]>
---
arch/arm64/boot/dts/freescale/imx8mm.dtsi | 43 +++++++++++++++++++++++++++++++
1 file changed, 43 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
index 3a62407..1870c89 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
@@ -70,6 +70,7 @@
nvmem-cells = <&cpu_speed_grade>;
nvmem-cell-names = "speed_grade";
cpu-idle-states = <&cpu_sleep_wait>;
+ #cooling-cells = <2>;
};
A53_1: cpu@1 {
@@ -82,6 +83,7 @@
next-level-cache = <&A53_L2>;
operating-points-v2 = <&a53_opp_table>;
cpu-idle-states = <&cpu_sleep_wait>;
+ #cooling-cells = <2>;
};
A53_2: cpu@2 {
@@ -94,6 +96,7 @@
next-level-cache = <&A53_L2>;
operating-points-v2 = <&a53_opp_table>;
cpu-idle-states = <&cpu_sleep_wait>;
+ #cooling-cells = <2>;
};
A53_3: cpu@3 {
@@ -106,6 +109,7 @@
next-level-cache = <&A53_L2>;
operating-points-v2 = <&a53_opp_table>;
cpu-idle-states = <&cpu_sleep_wait>;
+ #cooling-cells = <2>;
};
A53_L2: l2-cache0 {
@@ -209,6 +213,38 @@
arm,no-tick-in-suspend;
};
+ thermal-zones {
+ cpu-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <2000>;
+ thermal-sensors = <&tmu>;
+ trips {
+ cpu_alert0: trip0 {
+ temperature = <85000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu_crit0: trip1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert0>;
+ cooling-device =
+ <&A53_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A53_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A53_2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A53_3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+ };
+
usbphynop1: usbphynop1 {
compatible = "usb-nop-xceiv";
clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
@@ -368,6 +404,13 @@
gpio-ranges = <&iomuxc 0 119 30>;
};
+ tmu: tmu@30260000 {
+ compatible = "fsl,imx8mm-tmu";
+ reg = <0x30260000 0x10000>;
+ clocks = <&clk IMX8MM_CLK_TMU_ROOT>;
+ #thermal-sensor-cells = <0>;
+ };
+
wdog1: watchdog@30280000 {
compatible = "fsl,imx8mm-wdt", "fsl,imx21-wdt";
reg = <0x30280000 0x10000>;
--
2.7.4
On Thu, 4 Jul 2019 17:13:10 +0800, [email protected] wrote:
> From: Anson Huang <[email protected]>
>
> Add thermal binding doc for Freescale's i.MX8MM Thermal Monitoring Unit.
>
> Signed-off-by: Anson Huang <[email protected]>
> ---
> .../devicetree/bindings/thermal/imx8mm-thermal.txt | 15 +++++++++++++++
> 1 file changed, 15 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/thermal/imx8mm-thermal.txt
>
Reviewed-by: Rob Herring <[email protected]>