2019-08-07 10:54:11

by Faiz Abbas

[permalink] [raw]
Subject: [PATCH] ARM: dts: dra74x: Fix iodelay configuration for mmc3

According to the latest am572x[1] and dra74x[2] data manuals, mmc3
default, hs, sdr12 and sdr25 modes use iodelay values given in
MMC3_MANUAL1. Set the MODE_SELECT bit for these so that manual mode is
selected and correct iodelay values can be configured.

[1] http://www.ti.com/lit/ds/symlink/am5728.pdf
[2] http://www.ti.com/lit/ds/symlink/dra746.pdf

Signed-off-by: Faiz Abbas <[email protected]>
---
arch/arm/boot/dts/dra74x-mmc-iodelay.dtsi | 50 +++++++++++------------
1 file changed, 25 insertions(+), 25 deletions(-)

diff --git a/arch/arm/boot/dts/dra74x-mmc-iodelay.dtsi b/arch/arm/boot/dts/dra74x-mmc-iodelay.dtsi
index 28ebb4eb884a..214b9e6de2c3 100644
--- a/arch/arm/boot/dts/dra74x-mmc-iodelay.dtsi
+++ b/arch/arm/boot/dts/dra74x-mmc-iodelay.dtsi
@@ -32,7 +32,7 @@
*
* Datamanual Revisions:
*
- * AM572x Silicon Revision 2.0: SPRS953B, Revised November 2016
+ * AM572x Silicon Revision 2.0: SPRS953F, Revised May 2019
* AM572x Silicon Revision 1.1: SPRS915R, Revised November 2016
*
*/
@@ -229,45 +229,45 @@

mmc3_pins_default: mmc3_pins_default {
pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_clk.mmc3_clk */
- DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */
- DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */
- DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */
- DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */
- DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */
+ DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_clk.mmc3_clk */
+ DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */
+ DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */
+ DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */
+ DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */
+ DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */
>;
};

mmc3_pins_hs: mmc3_pins_hs {
pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_clk.mmc3_clk */
- DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */
- DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */
- DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */
- DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */
- DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */
+ DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_clk.mmc3_clk */
+ DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */
+ DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */
+ DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */
+ DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */
+ DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */
>;
};

mmc3_pins_sdr12: mmc3_pins_sdr12 {
pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_clk.mmc3_clk */
- DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */
- DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */
- DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */
- DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */
- DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */
+ DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_clk.mmc3_clk */
+ DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */
+ DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */
+ DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */
+ DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */
+ DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */
>;
};

mmc3_pins_sdr25: mmc3_pins_sdr25 {
pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_clk.mmc3_clk */
- DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */
- DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */
- DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */
- DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */
- DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */
+ DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_clk.mmc3_clk */
+ DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */
+ DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */
+ DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */
+ DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */
+ DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */
>;
};

--
2.19.2


2019-08-13 11:18:02

by Tony Lindgren

[permalink] [raw]
Subject: Re: [PATCH] ARM: dts: dra74x: Fix iodelay configuration for mmc3

* Faiz Abbas <[email protected]> [190807 03:53]:
> According to the latest am572x[1] and dra74x[2] data manuals, mmc3
> default, hs, sdr12 and sdr25 modes use iodelay values given in
> MMC3_MANUAL1. Set the MODE_SELECT bit for these so that manual mode is
> selected and correct iodelay values can be configured.

Thanks applying into fixes.

Tony