2019-08-21 14:20:10

by Beniamin Bia

Subject: [PATCH v3 4/4] dt-bindings: iio: adc: Add AD7606B ADC documentation

Documentation for AD7606B Analog to Digital Converter and software
mode was added.

Signed-off-by: Beniamin Bia <[email protected]>
---
Changes in v3:
-nothing changed

Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
index 509dbe9c84d2..2afe31747a70 100644
--- a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
+++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
@@ -13,6 +13,7 @@ maintainers:
description: |
Analog Devices AD7606 Simultaneous Sampling ADC
https://www.analog.com/media/en/technical-documentation/data-sheets/ad7606_7606-6_7606-4.pdf
+ https://www.analog.com/media/en/technical-documentation/data-sheets/AD7606B.pdf
https://www.analog.com/media/en/technical-documentation/data-sheets/AD7616.pdf

properties:
@@ -22,6 +23,7 @@ properties:
- adi,ad7606-8
- adi,ad7606-6
- adi,ad7606-4
+ - adi,ad7606b
- adi,ad7616

reg:
@@ -87,7 +89,7 @@ properties:

adi,sw-mode:
description:
- Software mode of operation, so far available only for ad7616.
+ Software mode of operation, so far available only for ad7616 and ad7606B.
It is enabled when all three oversampling mode pins are connected to
high level. The device is configured by the corresponding registers. If the
adi,oversampling-ratio-gpios property is defined, then the driver will set the
--
2.17.1

2019-08-25 17:28:28

by Jonathan Cameron

Subject: Re: [PATCH v3 4/4] dt-bindings: iio: adc: Add AD7606B ADC documentation

On Wed, 21 Aug 2019 17:16:56 +0300
Beniamin Bia <[email protected]> wrote:

> Documentation for AD7606B Analog to Digital Converter and software
> mode was added.
>
> Signed-off-by: Beniamin Bia <[email protected]>
Tweaked as per Peter's comment and added Rob's Reviewed-by from v2
Seems everyone decided to review this one just as you were posting
the new version ;)

Jonathan

> ---
> Changes in v3:
> -nothing changed
>
> Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml | 4 +++-
> 1 file changed, 3 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
> index 509dbe9c84d2..2afe31747a70 100644
> --- a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
> +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
> @@ -13,6 +13,7 @@ maintainers:
> description: |
> Analog Devices AD7606 Simultaneous Sampling ADC
> https://www.analog.com/media/en/technical-documentation/data-sheets/ad7606_7606-6_7606-4.pdf
> + https://www.analog.com/media/en/technical-documentation/data-sheets/AD7606B.pdf
> https://www.analog.com/media/en/technical-documentation/data-sheets/AD7616.pdf
>
> properties:
> @@ -22,6 +23,7 @@ properties:
> - adi,ad7606-8
> - adi,ad7606-6
> - adi,ad7606-4
> + - adi,ad7606b
> - adi,ad7616
>
> reg:
> @@ -87,7 +89,7 @@ properties:
>
> adi,sw-mode:
> description:
> - Software mode of operation, so far available only for ad7616.
> + Software mode of operation, so far available only for ad7616 and ad7606B.
> It is enabled when all three oversampling mode pins are connected to
> high level. The device is configured by the corresponding registers. If the
> adi,oversampling-ratio-gpios property is defined, then the driver will set the