2019-10-04 09:02:56

by Guillaume LA ROQUE

[permalink] [raw]
Subject: [PATCH v7 4/7] arm64: dts: meson: g12: Add minimal thermal zone

Add minimal thermal zone for two temperature sensor
One is located close to the DDR and the other one is
located close to the PLLs (between the CPU and GPU)

Acked-by: Martin Blumenstingl <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
Tested-by: Christian Hewitt <[email protected]>
Tested-by: Kevin Hilman <[email protected]>
Signed-off-by: Guillaume La Roque <[email protected]>
---
.../boot/dts/amlogic/meson-g12-common.dtsi | 57 +++++++++++++++++++
1 file changed, 57 insertions(+)

diff --git a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
index 0660d9ef6a86..a98c16e163c2 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
@@ -12,6 +12,7 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/reset/amlogic,meson-axg-audio-arb.h>
#include <dt-bindings/reset/amlogic,meson-g12a-reset.h>
+#include <dt-bindings/thermal/thermal.h>

/ {
interrupt-parent = <&gic>;
@@ -94,6 +95,61 @@
#size-cells = <2>;
ranges;

+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ polling-delay = <1000>;
+ polling-delay-passive = <100>;
+ thermal-sensors = <&cpu_temp>;
+
+ trips {
+ cpu_passive: cpu-passive {
+ temperature = <85000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "passive";
+ };
+
+ cpu_hot: cpu-hot {
+ temperature = <95000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "hot";
+ };
+
+ cpu_critical: cpu-critical {
+ temperature = <110000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "critical";
+ };
+ };
+ };
+
+ ddr_thermal: ddr-thermal {
+ polling-delay = <1000>;
+ polling-delay-passive = <100>;
+ thermal-sensors = <&ddr_temp>;
+
+ trips {
+ ddr_passive: ddr-passive {
+ temperature = <85000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "passive";
+ };
+
+ ddr_critical: ddr-critical {
+ temperature = <110000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map {
+ trip = <&ddr_passive>;
+ cooling-device = <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+ };
+
ethmac: ethernet@ff3f0000 {
compatible = "amlogic,meson-axg-dwmac",
"snps,dwmac-3.70a",
@@ -2412,6 +2468,7 @@
assigned-clock-rates = <0>, /* Do Nothing */
<800000000>,
<0>; /* Do Nothing */
+ #cooling-cells = <2>;
};
};

--
2.17.1


2019-10-16 07:37:31

by Amit Kucheria

[permalink] [raw]
Subject: Re: [PATCH v7 4/7] arm64: dts: meson: g12: Add minimal thermal zone

On Fri, Oct 4, 2019 at 2:31 PM Guillaume La Roque <[email protected]> wrote:
>
> Add minimal thermal zone for two temperature sensor
> One is located close to the DDR and the other one is
> located close to the PLLs (between the CPU and GPU)
>
> Acked-by: Martin Blumenstingl <[email protected]>
> Reviewed-by: Neil Armstrong <[email protected]>
> Tested-by: Christian Hewitt <[email protected]>
> Tested-by: Kevin Hilman <[email protected]>
> Signed-off-by: Guillaume La Roque <[email protected]>
> ---
> .../boot/dts/amlogic/meson-g12-common.dtsi | 57 +++++++++++++++++++
> 1 file changed, 57 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
> index 0660d9ef6a86..a98c16e163c2 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
> @@ -12,6 +12,7 @@
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/reset/amlogic,meson-axg-audio-arb.h>
> #include <dt-bindings/reset/amlogic,meson-g12a-reset.h>
> +#include <dt-bindings/thermal/thermal.h>
>
> / {
> interrupt-parent = <&gic>;
> @@ -94,6 +95,61 @@
> #size-cells = <2>;
> ranges;
>
> + thermal-zones {
> + cpu_thermal: cpu-thermal {
> + polling-delay = <1000>;
> + polling-delay-passive = <100>;

Ordinarily, you would need to set these delays to 0 in interrupt mode
to prevent polling overhead. I've just submitted a patch to of-thermal
that should fix this requirement. Could you check if it works for you?

> + thermal-sensors = <&cpu_temp>;
> +
> + trips {
> + cpu_passive: cpu-passive {
> + temperature = <85000>; /* millicelsius */
> + hysteresis = <2000>; /* millicelsius */
> + type = "passive";
> + };
> +
> + cpu_hot: cpu-hot {
> + temperature = <95000>; /* millicelsius */
> + hysteresis = <2000>; /* millicelsius */
> + type = "hot";
> + };
> +
> + cpu_critical: cpu-critical {
> + temperature = <110000>; /* millicelsius */
> + hysteresis = <2000>; /* millicelsius */
> + type = "critical";
> + };
> + };
> + };
> +
> + ddr_thermal: ddr-thermal {
> + polling-delay = <1000>;
> + polling-delay-passive = <100>;
> + thermal-sensors = <&ddr_temp>;
> +
> + trips {
> + ddr_passive: ddr-passive {
> + temperature = <85000>; /* millicelsius */
> + hysteresis = <2000>; /* millicelsius */
> + type = "passive";
> + };
> +
> + ddr_critical: ddr-critical {
> + temperature = <110000>; /* millicelsius */
> + hysteresis = <2000>; /* millicelsius */
> + type = "critical";
> + };
> + };
> +
> + cooling-maps {
> + map {
> + trip = <&ddr_passive>;
> + cooling-device = <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> + };
> + };
> + };
> +
> ethmac: ethernet@ff3f0000 {
> compatible = "amlogic,meson-axg-dwmac",
> "snps,dwmac-3.70a",
> @@ -2412,6 +2468,7 @@
> assigned-clock-rates = <0>, /* Do Nothing */
> <800000000>,
> <0>; /* Do Nothing */
> + #cooling-cells = <2>;
> };
> };
>
> --
> 2.17.1
>

2019-10-16 13:25:14

by Guillaume LA ROQUE

[permalink] [raw]
Subject: Re: [PATCH v7 4/7] arm64: dts: meson: g12: Add minimal thermal zone

Hi,

On 10/16/19 1:20 AM, Amit Kucheria wrote:
> On Fri, Oct 4, 2019 at 2:31 PM Guillaume La Roque <[email protected]> wrote:
>> Add minimal thermal zone for two temperature sensor
>> One is located close to the DDR and the other one is
>> located close to the PLLs (between the CPU and GPU)
>>
>> Acked-by: Martin Blumenstingl <[email protected]>
>> Reviewed-by: Neil Armstrong <[email protected]>
>> Tested-by: Christian Hewitt <[email protected]>
>> Tested-by: Kevin Hilman <[email protected]>
>> Signed-off-by: Guillaume La Roque <[email protected]>
>> ---
>> .../boot/dts/amlogic/meson-g12-common.dtsi | 57 +++++++++++++++++++
>> 1 file changed, 57 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
>> index 0660d9ef6a86..a98c16e163c2 100644
>> --- a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
>> +++ b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
>> @@ -12,6 +12,7 @@
>> #include <dt-bindings/interrupt-controller/arm-gic.h>
>> #include <dt-bindings/reset/amlogic,meson-axg-audio-arb.h>
>> #include <dt-bindings/reset/amlogic,meson-g12a-reset.h>
>> +#include <dt-bindings/thermal/thermal.h>
>>
>> / {
>> interrupt-parent = <&gic>;
>> @@ -94,6 +95,61 @@
>> #size-cells = <2>;
>> ranges;
>>
>> + thermal-zones {
>> + cpu_thermal: cpu-thermal {
>> + polling-delay = <1000>;
>> + polling-delay-passive = <100>;
> Ordinarily, you would need to set these delays to 0 in interrupt mode
> to prevent polling overhead. I've just submitted a patch to of-thermal
> that should fix this requirement. Could you check if it works for you?

it's working for me.

thanks for your review.

>> + thermal-sensors = <&cpu_temp>;
>> +
>> + trips {
>> + cpu_passive: cpu-passive {
>> + temperature = <85000>; /* millicelsius */
>> + hysteresis = <2000>; /* millicelsius */
>> + type = "passive";
>> + };
>> +
>> + cpu_hot: cpu-hot {
>> + temperature = <95000>; /* millicelsius */
>> + hysteresis = <2000>; /* millicelsius */
>> + type = "hot";
>> + };
>> +
>> + cpu_critical: cpu-critical {
>> + temperature = <110000>; /* millicelsius */
>> + hysteresis = <2000>; /* millicelsius */
>> + type = "critical";
>> + };
>> + };
>> + };
>> +
>> + ddr_thermal: ddr-thermal {
>> + polling-delay = <1000>;
>> + polling-delay-passive = <100>;
>> + thermal-sensors = <&ddr_temp>;
>> +
>> + trips {
>> + ddr_passive: ddr-passive {
>> + temperature = <85000>; /* millicelsius */
>> + hysteresis = <2000>; /* millicelsius */
>> + type = "passive";
>> + };
>> +
>> + ddr_critical: ddr-critical {
>> + temperature = <110000>; /* millicelsius */
>> + hysteresis = <2000>; /* millicelsius */
>> + type = "critical";
>> + };
>> + };
>> +
>> + cooling-maps {
>> + map {
>> + trip = <&ddr_passive>;
>> + cooling-device = <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>> + };
>> + };
>> + };
>> + };
>> +
>> ethmac: ethernet@ff3f0000 {
>> compatible = "amlogic,meson-axg-dwmac",
>> "snps,dwmac-3.70a",
>> @@ -2412,6 +2468,7 @@
>> assigned-clock-rates = <0>, /* Do Nothing */
>> <800000000>,
>> <0>; /* Do Nothing */
>> + #cooling-cells = <2>;
>> };
>> };
>>
>> --
>> 2.17.1
>>

2019-10-16 13:27:33

by Amit Kucheria

[permalink] [raw]
Subject: Re: [PATCH v7 4/7] arm64: dts: meson: g12: Add minimal thermal zone

On Fri, Oct 4, 2019 at 2:31 PM Guillaume La Roque <[email protected]> wrote:
>
> Add minimal thermal zone for two temperature sensor
> One is located close to the DDR and the other one is
> located close to the PLLs (between the CPU and GPU)
>
> Acked-by: Martin Blumenstingl <[email protected]>
> Reviewed-by: Neil Armstrong <[email protected]>
> Tested-by: Christian Hewitt <[email protected]>
> Tested-by: Kevin Hilman <[email protected]>
> Signed-off-by: Guillaume La Roque <[email protected]>

Reviewed-by: Amit Kucheria <[email protected]>

> ---
> .../boot/dts/amlogic/meson-g12-common.dtsi | 57 +++++++++++++++++++
> 1 file changed, 57 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
> index 0660d9ef6a86..a98c16e163c2 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
> @@ -12,6 +12,7 @@
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/reset/amlogic,meson-axg-audio-arb.h>
> #include <dt-bindings/reset/amlogic,meson-g12a-reset.h>
> +#include <dt-bindings/thermal/thermal.h>
>
> / {
> interrupt-parent = <&gic>;
> @@ -94,6 +95,61 @@
> #size-cells = <2>;
> ranges;
>
> + thermal-zones {
> + cpu_thermal: cpu-thermal {
> + polling-delay = <1000>;
> + polling-delay-passive = <100>;
> + thermal-sensors = <&cpu_temp>;
> +
> + trips {
> + cpu_passive: cpu-passive {
> + temperature = <85000>; /* millicelsius */
> + hysteresis = <2000>; /* millicelsius */
> + type = "passive";
> + };
> +
> + cpu_hot: cpu-hot {
> + temperature = <95000>; /* millicelsius */
> + hysteresis = <2000>; /* millicelsius */
> + type = "hot";
> + };
> +
> + cpu_critical: cpu-critical {
> + temperature = <110000>; /* millicelsius */
> + hysteresis = <2000>; /* millicelsius */
> + type = "critical";
> + };
> + };
> + };
> +
> + ddr_thermal: ddr-thermal {
> + polling-delay = <1000>;
> + polling-delay-passive = <100>;
> + thermal-sensors = <&ddr_temp>;
> +
> + trips {
> + ddr_passive: ddr-passive {
> + temperature = <85000>; /* millicelsius */
> + hysteresis = <2000>; /* millicelsius */
> + type = "passive";
> + };
> +
> + ddr_critical: ddr-critical {
> + temperature = <110000>; /* millicelsius */
> + hysteresis = <2000>; /* millicelsius */
> + type = "critical";
> + };
> + };
> +
> + cooling-maps {
> + map {
> + trip = <&ddr_passive>;
> + cooling-device = <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> + };
> + };
> + };
> +
> ethmac: ethernet@ff3f0000 {
> compatible = "amlogic,meson-axg-dwmac",
> "snps,dwmac-3.70a",
> @@ -2412,6 +2468,7 @@
> assigned-clock-rates = <0>, /* Do Nothing */
> <800000000>,
> <0>; /* Do Nothing */
> + #cooling-cells = <2>;
> };
> };
>
> --
> 2.17.1
>

2019-10-17 12:33:25

by Kevin Hilman

[permalink] [raw]
Subject: Re: [PATCH v7 4/7] arm64: dts: meson: g12: Add minimal thermal zone

Guillaume La Roque <[email protected]> writes:

> Add minimal thermal zone for two temperature sensor
> One is located close to the DDR and the other one is
> located close to the PLLs (between the CPU and GPU)

nit: subject should be "arm64: dts: amlogic" (not meson).

I fixed it up when applying,

Kevin

2019-10-18 21:05:03

by Kevin Hilman

[permalink] [raw]
Subject: Re: [PATCH v7 4/7] arm64: dts: meson: g12: Add minimal thermal zone

Kevin Hilman <[email protected]> writes:

> Guillaume La Roque <[email protected]> writes:
>
>> Add minimal thermal zone for two temperature sensor
>> One is located close to the DDR and the other one is
>> located close to the PLLs (between the CPU and GPU)
>
> nit: subject should be "arm64: dts: amlogic" (not meson).
>
> I fixed it up when applying,

I got it backwards, this one was right, the other ones with "amlogic"
should be "meson". I (re)fixed it in my 'v5.5/dt64' branch.

Kevin