Convert the STM32 dcmi binding to DT schema format using json-schema
Signed-off-by: Benjamin Gaignard <[email protected]>
---
changes in v3:
-use (GPL-2.0-only OR BSD-2-Clause) license
changes in v2:
- use BSD-2-Clause license
- remove useless dma descriptions
- fix clock property
- add additionalProperties: false
- fix reset indentation
.../devicetree/bindings/media/st,stm32-dcmi.txt | 45 -----------
.../devicetree/bindings/media/st,stm32-dcmi.yaml | 86 ++++++++++++++++++++++
2 files changed, 86 insertions(+), 45 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/media/st,stm32-dcmi.txt
create mode 100644 Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml
diff --git a/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt b/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt
deleted file mode 100644
index 3122ded82eb4..000000000000
--- a/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt
+++ /dev/null
@@ -1,45 +0,0 @@
-STMicroelectronics STM32 Digital Camera Memory Interface (DCMI)
-
-Required properties:
-- compatible: "st,stm32-dcmi"
-- reg: physical base address and length of the registers set for the device
-- interrupts: should contain IRQ line for the DCMI
-- resets: reference to a reset controller,
- see Documentation/devicetree/bindings/reset/st,stm32-rcc.txt
-- clocks: list of clock specifiers, corresponding to entries in
- the clock-names property
-- clock-names: must contain "mclk", which is the DCMI peripherial clock
-- pinctrl: the pincontrol settings to configure muxing properly
- for pins that connect to DCMI device.
- See Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml.
-- dmas: phandle to DMA controller node,
- see Documentation/devicetree/bindings/dma/stm32-dma.txt
-- dma-names: must contain "tx", which is the transmit channel from DCMI to DMA
-
-DCMI supports a single port node with parallel bus. It should contain one
-'port' child node with child 'endpoint' node. Please refer to the bindings
-defined in Documentation/devicetree/bindings/media/video-interfaces.txt.
-
-Example:
-
- dcmi: dcmi@50050000 {
- compatible = "st,stm32-dcmi";
- reg = <0x50050000 0x400>;
- interrupts = <78>;
- resets = <&rcc STM32F4_AHB2_RESET(DCMI)>;
- clocks = <&rcc 0 STM32F4_AHB2_CLOCK(DCMI)>;
- clock-names = "mclk";
- pinctrl-names = "default";
- pinctrl-0 = <&dcmi_pins>;
- dmas = <&dma2 1 1 0x414 0x3>;
- dma-names = "tx";
- port {
- dcmi_0: endpoint {
- remote-endpoint = <...>;
- bus-width = <8>;
- hsync-active = <0>;
- vsync-active = <0>;
- pclk-sample = <1>;
- };
- };
- };
diff --git a/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml b/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml
new file mode 100644
index 000000000000..3fe778cb5cc3
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml
@@ -0,0 +1,86 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/st,stm32-dcmi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectronics STM32 Digital Camera Memory Interface (DCMI) binding
+
+maintainers:
+ - Hugues Fruchet <[email protected]>
+
+properties:
+ compatible:
+ const: st,stm32-dcmi
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ clock-names:
+ items:
+ - const: mclk
+
+ dmas:
+ maxItems: 1
+
+ dma-names:
+ items:
+ - const: tx
+
+ resets:
+ maxItems: 1
+
+ port:
+ type: object
+ description:
+ DCMI supports a single port node with parallel bus. It should contain
+ one 'port' child node with child 'endpoint' node. Please refer to the
+ bindings defined in
+ Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - clock-names
+ - resets
+ - dmas
+ - dma-names
+ - port
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/clock/stm32mp1-clks.h>
+ #include <dt-bindings/reset/stm32mp1-resets.h>
+ dcmi: dcmi@4c006000 {
+ compatible = "st,stm32-dcmi";
+ reg = <0x4c006000 0x400>;
+ interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&rcc CAMITF_R>;
+ clocks = <&rcc DCMI>;
+ clock-names = "mclk";
+ dmas = <&dmamux1 75 0x400 0x0d>;
+ dma-names = "tx";
+
+ port {
+ dcmi_0: endpoint {
+ remote-endpoint = <&ov5640_0>;
+ bus-width = <8>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ pclk-sample = <1>;
+ };
+ };
+ };
+
+...
--
2.15.0
On Mon, 14 Oct 2019 11:20:21 +0200, Benjamin Gaignard wrote:
> Convert the STM32 dcmi binding to DT schema format using json-schema
>
> Signed-off-by: Benjamin Gaignard <[email protected]>
> ---
> changes in v3:
> -use (GPL-2.0-only OR BSD-2-Clause) license
>
> changes in v2:
> - use BSD-2-Clause license
> - remove useless dma descriptions
> - fix clock property
> - add additionalProperties: false
> - fix reset indentation
>
> .../devicetree/bindings/media/st,stm32-dcmi.txt | 45 -----------
> .../devicetree/bindings/media/st,stm32-dcmi.yaml | 86 ++++++++++++++++++++++
> 2 files changed, 86 insertions(+), 45 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/media/st,stm32-dcmi.txt
> create mode 100644 Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml
>
Applied, thanks.
Rob
On 10/14/19 11:20 AM, Benjamin Gaignard wrote:
> Convert the STM32 dcmi binding to DT schema format using json-schema
It looks like the MAINTAINERS entry isn't updated. Can you post a separate patch for that?
Hans
>
> Signed-off-by: Benjamin Gaignard <[email protected]>
> ---
> changes in v3:
> -use (GPL-2.0-only OR BSD-2-Clause) license
>
> changes in v2:
> - use BSD-2-Clause license
> - remove useless dma descriptions
> - fix clock property
> - add additionalProperties: false
> - fix reset indentation
>
> .../devicetree/bindings/media/st,stm32-dcmi.txt | 45 -----------
> .../devicetree/bindings/media/st,stm32-dcmi.yaml | 86 ++++++++++++++++++++++
> 2 files changed, 86 insertions(+), 45 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/media/st,stm32-dcmi.txt
> create mode 100644 Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml
>
> diff --git a/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt b/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt
> deleted file mode 100644
> index 3122ded82eb4..000000000000
> --- a/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt
> +++ /dev/null
> @@ -1,45 +0,0 @@
> -STMicroelectronics STM32 Digital Camera Memory Interface (DCMI)
> -
> -Required properties:
> -- compatible: "st,stm32-dcmi"
> -- reg: physical base address and length of the registers set for the device
> -- interrupts: should contain IRQ line for the DCMI
> -- resets: reference to a reset controller,
> - see Documentation/devicetree/bindings/reset/st,stm32-rcc.txt
> -- clocks: list of clock specifiers, corresponding to entries in
> - the clock-names property
> -- clock-names: must contain "mclk", which is the DCMI peripherial clock
> -- pinctrl: the pincontrol settings to configure muxing properly
> - for pins that connect to DCMI device.
> - See Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml.
> -- dmas: phandle to DMA controller node,
> - see Documentation/devicetree/bindings/dma/stm32-dma.txt
> -- dma-names: must contain "tx", which is the transmit channel from DCMI to DMA
> -
> -DCMI supports a single port node with parallel bus. It should contain one
> -'port' child node with child 'endpoint' node. Please refer to the bindings
> -defined in Documentation/devicetree/bindings/media/video-interfaces.txt.
> -
> -Example:
> -
> - dcmi: dcmi@50050000 {
> - compatible = "st,stm32-dcmi";
> - reg = <0x50050000 0x400>;
> - interrupts = <78>;
> - resets = <&rcc STM32F4_AHB2_RESET(DCMI)>;
> - clocks = <&rcc 0 STM32F4_AHB2_CLOCK(DCMI)>;
> - clock-names = "mclk";
> - pinctrl-names = "default";
> - pinctrl-0 = <&dcmi_pins>;
> - dmas = <&dma2 1 1 0x414 0x3>;
> - dma-names = "tx";
> - port {
> - dcmi_0: endpoint {
> - remote-endpoint = <...>;
> - bus-width = <8>;
> - hsync-active = <0>;
> - vsync-active = <0>;
> - pclk-sample = <1>;
> - };
> - };
> - };
> diff --git a/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml b/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml
> new file mode 100644
> index 000000000000..3fe778cb5cc3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml
> @@ -0,0 +1,86 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/media/st,stm32-dcmi.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: STMicroelectronics STM32 Digital Camera Memory Interface (DCMI) binding
> +
> +maintainers:
> + - Hugues Fruchet <[email protected]>
> +
> +properties:
> + compatible:
> + const: st,stm32-dcmi
> +
> + reg:
> + maxItems: 1
> +
> + interrupts:
> + maxItems: 1
> +
> + clocks:
> + maxItems: 1
> +
> + clock-names:
> + items:
> + - const: mclk
> +
> + dmas:
> + maxItems: 1
> +
> + dma-names:
> + items:
> + - const: tx
> +
> + resets:
> + maxItems: 1
> +
> + port:
> + type: object
> + description:
> + DCMI supports a single port node with parallel bus. It should contain
> + one 'port' child node with child 'endpoint' node. Please refer to the
> + bindings defined in
> + Documentation/devicetree/bindings/media/video-interfaces.txt.
> +
> +required:
> + - compatible
> + - reg
> + - interrupts
> + - clocks
> + - clock-names
> + - resets
> + - dmas
> + - dma-names
> + - port
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/clock/stm32mp1-clks.h>
> + #include <dt-bindings/reset/stm32mp1-resets.h>
> + dcmi: dcmi@4c006000 {
> + compatible = "st,stm32-dcmi";
> + reg = <0x4c006000 0x400>;
> + interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
> + resets = <&rcc CAMITF_R>;
> + clocks = <&rcc DCMI>;
> + clock-names = "mclk";
> + dmas = <&dmamux1 75 0x400 0x0d>;
> + dma-names = "tx";
> +
> + port {
> + dcmi_0: endpoint {
> + remote-endpoint = <&ov5640_0>;
> + bus-width = <8>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + pclk-sample = <1>;
> + };
> + };
> + };
> +
> +...
>