The dsa_switch structure represents the physical switch device itself,
and is allocated by the driver. The dsa_switch_tree and dsa_port structures
represent the logical switch fabric (eventually composed of multiple switch
devices) and its ports, and are allocated by the DSA core.
This branch lists the logical ports directly in the fabric which simplifies
the iteration over all ports when assigning the default CPU port or configuring
the D in DSA in drivers like mv88e6xxx.
This also removes the unique dst->cpu_dp pointer and is a first step towards
supporting multiple CPU ports and dropping the DSA_MAX_PORTS limitation.
Because the dsa_port structures are not tight to the dsa_switch structure
anymore, we do not need to provide an helper for the drivers to allocate a
switch structure. Like in many other subsystems, drivers can now embed their
dsa_switch structure as they wish into their private structure. This will
be particularly interesting for the Broadcom drivers which were currently
limited by the dynamically allocated array of DSA ports.
The series implements the list of dsa_port structures, makes use of it,
then drops dst->cpu_dp and the dsa_switch_alloc helper.
Changes in v2:
- use list_add_tail instead of list_add to respect ports order
- use a single return statement for dsa_to_port
- remove pr_info messages
- put comments under appropriate branches
- add Git tags from reviewers
Vivien Didelot (16):
net: dsa: use dsa_to_port helper everywhere
net: dsa: add ports list in the switch fabric
net: dsa: use ports list in dsa_to_port
net: dsa: use ports list to find slave
net: dsa: use ports list to setup switches
net: dsa: use ports list for routing table setup
net: dsa: use ports list to find a port by node
net: dsa: use ports list to setup multiple master devices
net: dsa: use ports list to find first CPU port
net: dsa: use ports list to setup default CPU port
net: dsa: mv88e6xxx: silently skip PVT ops
net: dsa: mv88e6xxx: use ports list to map port VLAN
net: dsa: mv88e6xxx: use ports list to map bridge
net: dsa: sja1105: register switch before assigning port private data
net: dsa: allocate ports on touch
net: dsa: remove dsa_switch_alloc helper
drivers/net/dsa/b53/b53_common.c | 11 +-
drivers/net/dsa/bcm_sf2.c | 8 +-
drivers/net/dsa/bcm_sf2_cfp.c | 6 +-
drivers/net/dsa/dsa_loop.c | 5 +-
drivers/net/dsa/lan9303-core.c | 4 +-
drivers/net/dsa/lantiq_gswip.c | 4 +-
drivers/net/dsa/microchip/ksz_common.c | 5 +-
drivers/net/dsa/mt7530.c | 17 +-
drivers/net/dsa/mv88e6060.c | 4 +-
drivers/net/dsa/mv88e6xxx/chip.c | 90 ++++----
drivers/net/dsa/qca8k.c | 7 +-
drivers/net/dsa/realtek-smi-core.c | 5 +-
drivers/net/dsa/sja1105/sja1105_main.c | 37 ++--
drivers/net/dsa/vitesse-vsc73xx-core.c | 5 +-
include/net/dsa.h | 26 ++-
net/dsa/dsa.c | 8 +-
net/dsa/dsa2.c | 274 +++++++++++++------------
net/dsa/dsa_priv.h | 23 +--
net/dsa/switch.c | 4 +-
net/dsa/tag_8021q.c | 6 +-
20 files changed, 292 insertions(+), 257 deletions(-)
--
2.23.0
Use the new ports list instead of accessing the dsa_switch array
of ports in the dsa_to_port helper.
Signed-off-by: Vivien Didelot <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
---
include/net/dsa.h | 9 ++++++++-
1 file changed, 8 insertions(+), 1 deletion(-)
diff --git a/include/net/dsa.h b/include/net/dsa.h
index 6ff6dfcdc61d..d2b7ee28f3fd 100644
--- a/include/net/dsa.h
+++ b/include/net/dsa.h
@@ -285,7 +285,14 @@ struct dsa_switch {
static inline struct dsa_port *dsa_to_port(struct dsa_switch *ds, int p)
{
- return &ds->ports[p];
+ struct dsa_switch_tree *dst = ds->dst;
+ struct dsa_port *dp = NULL;
+
+ list_for_each_entry(dp, &dst->ports, list)
+ if (dp->ds == ds && dp->index == p)
+ break;
+
+ return dp;
}
static inline bool dsa_is_unused_port(struct dsa_switch *ds, int p)
--
2.23.0
Use the new ports list instead of iterating over switches and their
ports when looking for a slave device from a given master interface.
Signed-off-by: Vivien Didelot <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
---
net/dsa/dsa_priv.h | 23 ++++++-----------------
1 file changed, 6 insertions(+), 17 deletions(-)
diff --git a/net/dsa/dsa_priv.h b/net/dsa/dsa_priv.h
index 12f8c7ee4dd8..53e7577896b6 100644
--- a/net/dsa/dsa_priv.h
+++ b/net/dsa/dsa_priv.h
@@ -104,25 +104,14 @@ static inline struct net_device *dsa_master_find_slave(struct net_device *dev,
{
struct dsa_port *cpu_dp = dev->dsa_ptr;
struct dsa_switch_tree *dst = cpu_dp->dst;
- struct dsa_switch *ds;
- struct dsa_port *slave_port;
+ struct dsa_port *dp;
- if (device < 0 || device >= DSA_MAX_SWITCHES)
- return NULL;
+ list_for_each_entry(dp, &dst->ports, list)
+ if (dp->ds->index == device && dp->index == port &&
+ dp->type == DSA_PORT_TYPE_USER)
+ return dp->slave;
- ds = dst->ds[device];
- if (!ds)
- return NULL;
-
- if (port < 0 || port >= ds->num_ports)
- return NULL;
-
- slave_port = &ds->ports[port];
-
- if (unlikely(slave_port->type != DSA_PORT_TYPE_USER))
- return NULL;
-
- return slave_port->slave;
+ return NULL;
}
/* port.c */
--
2.23.0
Use the new ports list instead of iterating over switches and their
ports when setting up the switches and their ports.
At the same time, provide setup states and messages for ports and
switches as it is done for the trees.
Signed-off-by: Vivien Didelot <[email protected]>
---
include/net/dsa.h | 4 ++
net/dsa/dsa2.c | 93 +++++++++++++++++++++--------------------------
2 files changed, 45 insertions(+), 52 deletions(-)
diff --git a/include/net/dsa.h b/include/net/dsa.h
index d2b7ee28f3fd..bd08bdee8341 100644
--- a/include/net/dsa.h
+++ b/include/net/dsa.h
@@ -215,9 +215,13 @@ struct dsa_port {
* Original copy of the master netdev net_device_ops
*/
const struct net_device_ops *orig_ndo_ops;
+
+ bool setup;
};
struct dsa_switch {
+ bool setup;
+
struct device *dev;
/*
diff --git a/net/dsa/dsa2.c b/net/dsa/dsa2.c
index ba27ff8b4445..01b6047d9b7b 100644
--- a/net/dsa/dsa2.c
+++ b/net/dsa/dsa2.c
@@ -267,6 +267,9 @@ static int dsa_port_setup(struct dsa_port *dp)
bool dsa_port_enabled = false;
int err = 0;
+ if (dp->setup)
+ return 0;
+
switch (dp->type) {
case DSA_PORT_TYPE_UNUSED:
dsa_port_disable(dp);
@@ -335,14 +338,21 @@ static int dsa_port_setup(struct dsa_port *dp)
dsa_port_link_unregister_of(dp);
if (err && devlink_port_registered)
devlink_port_unregister(dlp);
+ if (err)
+ return err;
- return err;
+ dp->setup = true;
+
+ return 0;
}
static void dsa_port_teardown(struct dsa_port *dp)
{
struct devlink_port *dlp = &dp->devlink_port;
+ if (!dp->setup)
+ return;
+
switch (dp->type) {
case DSA_PORT_TYPE_UNUSED:
break;
@@ -365,11 +375,16 @@ static void dsa_port_teardown(struct dsa_port *dp)
}
break;
}
+
+ dp->setup = false;
}
static int dsa_switch_setup(struct dsa_switch *ds)
{
- int err = 0;
+ int err;
+
+ if (ds->setup)
+ return 0;
/* Initialize ds->phys_mii_mask before registering the slave MDIO bus
* driver and before ops->setup() has run, since the switch drivers and
@@ -411,6 +426,8 @@ static int dsa_switch_setup(struct dsa_switch *ds)
goto unregister_notifier;
}
+ ds->setup = true;
+
return 0;
unregister_notifier:
@@ -426,6 +443,9 @@ static int dsa_switch_setup(struct dsa_switch *ds)
static void dsa_switch_teardown(struct dsa_switch *ds)
{
+ if (!ds->setup)
+ return;
+
if (ds->slave_mii_bus && ds->ops->phy_read)
mdiobus_unregister(ds->slave_mii_bus);
@@ -440,78 +460,47 @@ static void dsa_switch_teardown(struct dsa_switch *ds)
ds->devlink = NULL;
}
+ ds->setup = false;
}
static int dsa_tree_setup_switches(struct dsa_switch_tree *dst)
{
- struct dsa_switch *ds;
struct dsa_port *dp;
- int device, port, i;
- int err = 0;
-
- for (device = 0; device < DSA_MAX_SWITCHES; device++) {
- ds = dst->ds[device];
- if (!ds)
- continue;
+ int err;
- err = dsa_switch_setup(ds);
+ list_for_each_entry(dp, &dst->ports, list) {
+ err = dsa_switch_setup(dp->ds);
if (err)
- goto switch_teardown;
-
- for (port = 0; port < ds->num_ports; port++) {
- dp = &ds->ports[port];
+ goto teardown;
+ }
- err = dsa_port_setup(dp);
- if (err)
- goto ports_teardown;
- }
+ list_for_each_entry(dp, &dst->ports, list) {
+ err = dsa_port_setup(dp);
+ if (err)
+ goto teardown;
}
return 0;
-ports_teardown:
- for (i = 0; i < port; i++)
- dsa_port_teardown(&ds->ports[i]);
-
- dsa_switch_teardown(ds);
-
-switch_teardown:
- for (i = 0; i < device; i++) {
- ds = dst->ds[i];
- if (!ds)
- continue;
-
- for (port = 0; port < ds->num_ports; port++) {
- dp = &ds->ports[port];
-
- dsa_port_teardown(dp);
- }
+teardown:
+ list_for_each_entry(dp, &dst->ports, list)
+ dsa_port_teardown(dp);
- dsa_switch_teardown(ds);
- }
+ list_for_each_entry(dp, &dst->ports, list)
+ dsa_switch_teardown(dp->ds);
return err;
}
static void dsa_tree_teardown_switches(struct dsa_switch_tree *dst)
{
- struct dsa_switch *ds;
struct dsa_port *dp;
- int device, port;
- for (device = 0; device < DSA_MAX_SWITCHES; device++) {
- ds = dst->ds[device];
- if (!ds)
- continue;
+ list_for_each_entry(dp, &dst->ports, list)
+ dsa_port_teardown(dp);
- for (port = 0; port < ds->num_ports; port++) {
- dp = &ds->ports[port];
-
- dsa_port_teardown(dp);
- }
-
- dsa_switch_teardown(ds);
- }
+ list_for_each_entry(dp, &dst->ports, list)
+ dsa_switch_teardown(dp->ds);
}
static int dsa_tree_setup_master(struct dsa_switch_tree *dst)
--
2.23.0
Use the new ports list instead of iterating over switches and their
ports to find a port from a given node.
Signed-off-by: Vivien Didelot <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
---
net/dsa/dsa2.c | 17 +++--------------
1 file changed, 3 insertions(+), 14 deletions(-)
diff --git a/net/dsa/dsa2.c b/net/dsa/dsa2.c
index 623805ba8e1a..a4de7ff8b19b 100644
--- a/net/dsa/dsa2.c
+++ b/net/dsa/dsa2.c
@@ -113,22 +113,11 @@ static bool dsa_port_is_user(struct dsa_port *dp)
static struct dsa_port *dsa_tree_find_port_by_node(struct dsa_switch_tree *dst,
struct device_node *dn)
{
- struct dsa_switch *ds;
struct dsa_port *dp;
- int device, port;
-
- for (device = 0; device < DSA_MAX_SWITCHES; device++) {
- ds = dst->ds[device];
- if (!ds)
- continue;
- for (port = 0; port < ds->num_ports; port++) {
- dp = &ds->ports[port];
-
- if (dp->dn == dn)
- return dp;
- }
- }
+ list_for_each_entry(dp, &dst->ports, list)
+ if (dp->dn == dn)
+ return dp;
return NULL;
}
--
2.23.0
Use the new ports list instead of iterating over switches and their
ports when looking up the first CPU port in the tree.
Signed-off-by: Vivien Didelot <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
---
net/dsa/dsa2.c | 17 +++--------------
1 file changed, 3 insertions(+), 14 deletions(-)
diff --git a/net/dsa/dsa2.c b/net/dsa/dsa2.c
index 514c0195e2e8..80191c7702a9 100644
--- a/net/dsa/dsa2.c
+++ b/net/dsa/dsa2.c
@@ -186,22 +186,11 @@ static bool dsa_tree_setup_routing_table(struct dsa_switch_tree *dst)
static struct dsa_port *dsa_tree_find_first_cpu(struct dsa_switch_tree *dst)
{
- struct dsa_switch *ds;
struct dsa_port *dp;
- int device, port;
-
- for (device = 0; device < DSA_MAX_SWITCHES; device++) {
- ds = dst->ds[device];
- if (!ds)
- continue;
- for (port = 0; port < ds->num_ports; port++) {
- dp = &ds->ports[port];
-
- if (dsa_port_is_cpu(dp))
- return dp;
- }
- }
+ list_for_each_entry(dp, &dst->ports, list)
+ if (dsa_port_is_cpu(dp))
+ return dp;
return NULL;
}
--
2.23.0
Instead of digging into the other dsa_switch structures of the fabric
and relying too much on the dsa_to_port helper, use the new list of
switch fabric ports to define the mask of the local ports allowed to
receive frames from another port of the fabric.
Signed-off-by: Vivien Didelot <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
---
drivers/net/dsa/mv88e6xxx/chip.c | 32 ++++++++++++++++++++------------
1 file changed, 20 insertions(+), 12 deletions(-)
diff --git a/drivers/net/dsa/mv88e6xxx/chip.c b/drivers/net/dsa/mv88e6xxx/chip.c
index 510ccdc2d03c..af8943142053 100644
--- a/drivers/net/dsa/mv88e6xxx/chip.c
+++ b/drivers/net/dsa/mv88e6xxx/chip.c
@@ -1057,35 +1057,43 @@ static int mv88e6xxx_set_mac_eee(struct dsa_switch *ds, int port,
return 0;
}
+/* Mask of the local ports allowed to receive frames from a given fabric port */
static u16 mv88e6xxx_port_vlan(struct mv88e6xxx_chip *chip, int dev, int port)
{
- struct dsa_switch *ds = NULL;
+ struct dsa_switch *ds = chip->ds;
+ struct dsa_switch_tree *dst = ds->dst;
struct net_device *br;
+ struct dsa_port *dp;
+ bool found = false;
u16 pvlan;
- int i;
- if (dev < DSA_MAX_SWITCHES)
- ds = chip->ds->dst->ds[dev];
+ list_for_each_entry(dp, &dst->ports, list) {
+ if (dp->ds->index == dev && dp->index == port) {
+ found = true;
+ break;
+ }
+ }
/* Prevent frames from unknown switch or port */
- if (!ds || port >= ds->num_ports)
+ if (!found)
return 0;
/* Frames from DSA links and CPU ports can egress any local port */
- if (dsa_is_cpu_port(ds, port) || dsa_is_dsa_port(ds, port))
+ if (dp->type == DSA_PORT_TYPE_CPU || dp->type == DSA_PORT_TYPE_DSA)
return mv88e6xxx_port_mask(chip);
- br = dsa_to_port(ds, port)->bridge_dev;
+ br = dp->bridge_dev;
pvlan = 0;
/* Frames from user ports can egress any local DSA links and CPU ports,
* as well as any local member of their bridge group.
*/
- for (i = 0; i < mv88e6xxx_num_ports(chip); ++i)
- if (dsa_is_cpu_port(chip->ds, i) ||
- dsa_is_dsa_port(chip->ds, i) ||
- (br && dsa_to_port(chip->ds, i)->bridge_dev == br))
- pvlan |= BIT(i);
+ list_for_each_entry(dp, &dst->ports, list)
+ if (dp->ds == ds &&
+ (dp->type == DSA_PORT_TYPE_CPU ||
+ dp->type == DSA_PORT_TYPE_DSA ||
+ (br && dp->bridge_dev == br)))
+ pvlan |= BIT(dp->index);
return pvlan;
}
--
2.23.0
Allocate the struct dsa_port the first time it is accessed with
dsa_port_touch, and remove the static dsa_port array from the
dsa_switch structure.
Signed-off-by: Vivien Didelot <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
---
include/net/dsa.h | 2 --
net/dsa/dsa2.c | 16 ++++++++++++++--
2 files changed, 14 insertions(+), 4 deletions(-)
diff --git a/include/net/dsa.h b/include/net/dsa.h
index f572134eb5de..9bc1d3f71f89 100644
--- a/include/net/dsa.h
+++ b/include/net/dsa.h
@@ -277,9 +277,7 @@ struct dsa_switch {
*/
bool vlan_filtering;
- /* Dynamically allocated ports, keep last */
size_t num_ports;
- struct dsa_port ports[];
};
static inline struct dsa_port *dsa_to_port(struct dsa_switch *ds, int p)
diff --git a/net/dsa/dsa2.c b/net/dsa/dsa2.c
index bf8b4e0fcb4f..83cba4623698 100644
--- a/net/dsa/dsa2.c
+++ b/net/dsa/dsa2.c
@@ -588,7 +588,13 @@ static struct dsa_port *dsa_port_touch(struct dsa_switch *ds, int index)
struct dsa_switch_tree *dst = ds->dst;
struct dsa_port *dp;
- dp = &ds->ports[index];
+ list_for_each_entry(dp, &dst->ports, list)
+ if (dp->ds == ds && dp->index == index)
+ return dp;
+
+ dp = kzalloc(sizeof(*dp), GFP_KERNEL);
+ if (!dp)
+ return NULL;
dp->ds = ds;
dp->index = index;
@@ -857,7 +863,7 @@ struct dsa_switch *dsa_switch_alloc(struct device *dev, size_t n)
{
struct dsa_switch *ds;
- ds = devm_kzalloc(dev, struct_size(ds, ports, n), GFP_KERNEL);
+ ds = devm_kzalloc(dev, sizeof(*ds), GFP_KERNEL);
if (!ds)
return NULL;
@@ -885,6 +891,12 @@ static void dsa_switch_remove(struct dsa_switch *ds)
{
struct dsa_switch_tree *dst = ds->dst;
unsigned int index = ds->index;
+ struct dsa_port *dp, *next;
+
+ list_for_each_entry_safe(dp, next, &dst->ports, list) {
+ list_del(&dp->list);
+ kfree(dp);
+ }
dsa_tree_remove_switch(dst, index);
}
--
2.23.0
Now that ports are dynamically listed in the fabric, there is no need
to provide a special helper to allocate the dsa_switch structure. This
will give more flexibility to drivers to embed this structure as they
wish in their private structure.
Signed-off-by: Vivien Didelot <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
---
drivers/net/dsa/b53/b53_common.c | 5 ++++-
drivers/net/dsa/dsa_loop.c | 5 ++++-
drivers/net/dsa/lan9303-core.c | 4 +++-
drivers/net/dsa/lantiq_gswip.c | 4 +++-
drivers/net/dsa/microchip/ksz_common.c | 5 ++++-
drivers/net/dsa/mt7530.c | 5 ++++-
drivers/net/dsa/mv88e6060.c | 4 +++-
drivers/net/dsa/mv88e6xxx/chip.c | 4 +++-
drivers/net/dsa/qca8k.c | 5 ++++-
drivers/net/dsa/realtek-smi-core.c | 5 ++++-
drivers/net/dsa/sja1105/sja1105_main.c | 4 +++-
drivers/net/dsa/vitesse-vsc73xx-core.c | 5 ++++-
include/net/dsa.h | 1 -
net/dsa/dsa2.c | 21 ++++++---------------
14 files changed, 49 insertions(+), 28 deletions(-)
diff --git a/drivers/net/dsa/b53/b53_common.c b/drivers/net/dsa/b53/b53_common.c
index aef9b56781ef..baadf622ac55 100644
--- a/drivers/net/dsa/b53/b53_common.c
+++ b/drivers/net/dsa/b53/b53_common.c
@@ -2341,10 +2341,13 @@ struct b53_device *b53_switch_alloc(struct device *base,
struct dsa_switch *ds;
struct b53_device *dev;
- ds = dsa_switch_alloc(base, DSA_MAX_PORTS);
+ ds = devm_kzalloc(base, sizeof(*ds), GFP_KERNEL);
if (!ds)
return NULL;
+ ds->dev = base;
+ ds->num_ports = DSA_MAX_PORTS;
+
dev = devm_kzalloc(base, sizeof(*dev), GFP_KERNEL);
if (!dev)
return NULL;
diff --git a/drivers/net/dsa/dsa_loop.c b/drivers/net/dsa/dsa_loop.c
index 925ed135a4d9..c8d7ef27fd72 100644
--- a/drivers/net/dsa/dsa_loop.c
+++ b/drivers/net/dsa/dsa_loop.c
@@ -286,10 +286,13 @@ static int dsa_loop_drv_probe(struct mdio_device *mdiodev)
dev_info(&mdiodev->dev, "%s: 0x%0x\n",
pdata->name, pdata->enabled_ports);
- ds = dsa_switch_alloc(&mdiodev->dev, DSA_MAX_PORTS);
+ ds = devm_kzalloc(&mdiodev->dev, sizeof(*ds), GFP_KERNEL);
if (!ds)
return -ENOMEM;
+ ds->dev = &mdiodev->dev;
+ ds->num_ports = DSA_MAX_PORTS;
+
ps = devm_kzalloc(&mdiodev->dev, sizeof(*ps), GFP_KERNEL);
if (!ps)
return -ENOMEM;
diff --git a/drivers/net/dsa/lan9303-core.c b/drivers/net/dsa/lan9303-core.c
index bbec86b9418e..e3c333a8f45d 100644
--- a/drivers/net/dsa/lan9303-core.c
+++ b/drivers/net/dsa/lan9303-core.c
@@ -1283,10 +1283,12 @@ static int lan9303_register_switch(struct lan9303 *chip)
{
int base;
- chip->ds = dsa_switch_alloc(chip->dev, LAN9303_NUM_PORTS);
+ chip->ds = devm_kzalloc(chip->dev, sizeof(*chip->ds), GFP_KERNEL);
if (!chip->ds)
return -ENOMEM;
+ chip->ds->dev = chip->dev;
+ chip->ds->num_ports = LAN9303_NUM_PORTS;
chip->ds->priv = chip;
chip->ds->ops = &lan9303_switch_ops;
base = chip->phy_addr_base;
diff --git a/drivers/net/dsa/lantiq_gswip.c b/drivers/net/dsa/lantiq_gswip.c
index a69c9b9878b7..955324968b74 100644
--- a/drivers/net/dsa/lantiq_gswip.c
+++ b/drivers/net/dsa/lantiq_gswip.c
@@ -1854,10 +1854,12 @@ static int gswip_probe(struct platform_device *pdev)
if (!priv->hw_info)
return -EINVAL;
- priv->ds = dsa_switch_alloc(dev, priv->hw_info->max_ports);
+ priv->ds = devm_kzalloc(dev, sizeof(*priv->ds), GFP_KERNEL);
if (!priv->ds)
return -ENOMEM;
+ priv->ds->dev = dev;
+ priv->ds->num_ports = priv->hw_info->max_ports;
priv->ds->priv = priv;
priv->ds->ops = &gswip_switch_ops;
priv->dev = dev;
diff --git a/drivers/net/dsa/microchip/ksz_common.c b/drivers/net/dsa/microchip/ksz_common.c
index fe47180c908b..5d08e4430824 100644
--- a/drivers/net/dsa/microchip/ksz_common.c
+++ b/drivers/net/dsa/microchip/ksz_common.c
@@ -398,10 +398,13 @@ struct ksz_device *ksz_switch_alloc(struct device *base, void *priv)
struct dsa_switch *ds;
struct ksz_device *swdev;
- ds = dsa_switch_alloc(base, DSA_MAX_PORTS);
+ ds = devm_kzalloc(base, sizeof(*ds), GFP_KERNEL);
if (!ds)
return NULL;
+ ds->dev = base;
+ ds->num_ports = DSA_MAX_PORTS;
+
swdev = devm_kzalloc(base, sizeof(*swdev), GFP_KERNEL);
if (!swdev)
return NULL;
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index a91293e47a57..add9e4279176 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -1632,10 +1632,13 @@ mt7530_probe(struct mdio_device *mdiodev)
if (!priv)
return -ENOMEM;
- priv->ds = dsa_switch_alloc(&mdiodev->dev, DSA_MAX_PORTS);
+ priv->ds = devm_kzalloc(&mdiodev->dev, sizeof(*priv->ds), GFP_KERNEL);
if (!priv->ds)
return -ENOMEM;
+ priv->ds->dev = &mdiodev->dev;
+ priv->ds->num_ports = DSA_MAX_PORTS;
+
/* Use medatek,mcm property to distinguish hardware type that would
* casues a little bit differences on power-on sequence.
*/
diff --git a/drivers/net/dsa/mv88e6060.c b/drivers/net/dsa/mv88e6060.c
index 2a2489b5196d..a5a37f47b320 100644
--- a/drivers/net/dsa/mv88e6060.c
+++ b/drivers/net/dsa/mv88e6060.c
@@ -270,10 +270,12 @@ static int mv88e6060_probe(struct mdio_device *mdiodev)
dev_info(dev, "switch %s detected\n", name);
- ds = dsa_switch_alloc(dev, MV88E6060_PORTS);
+ ds = devm_kzalloc(dev, sizeof(*ds), GFP_KERNEL);
if (!ds)
return -ENOMEM;
+ ds->dev = dev;
+ ds->num_ports = MV88E6060_PORTS;
ds->priv = priv;
ds->dev = dev;
ds->ops = &mv88e6060_switch_ops;
diff --git a/drivers/net/dsa/mv88e6xxx/chip.c b/drivers/net/dsa/mv88e6xxx/chip.c
index 826ae82ed727..41c61a747931 100644
--- a/drivers/net/dsa/mv88e6xxx/chip.c
+++ b/drivers/net/dsa/mv88e6xxx/chip.c
@@ -4978,10 +4978,12 @@ static int mv88e6xxx_register_switch(struct mv88e6xxx_chip *chip)
struct device *dev = chip->dev;
struct dsa_switch *ds;
- ds = dsa_switch_alloc(dev, mv88e6xxx_num_ports(chip));
+ ds = devm_kzalloc(dev, sizeof(*ds), GFP_KERNEL);
if (!ds)
return -ENOMEM;
+ ds->dev = dev;
+ ds->num_ports = mv88e6xxx_num_ports(chip);
ds->priv = chip;
ds->dev = dev;
ds->ops = &mv88e6xxx_switch_ops;
diff --git a/drivers/net/dsa/qca8k.c b/drivers/net/dsa/qca8k.c
index 71e44c8763b8..7e742cd491e8 100644
--- a/drivers/net/dsa/qca8k.c
+++ b/drivers/net/dsa/qca8k.c
@@ -1077,10 +1077,13 @@ qca8k_sw_probe(struct mdio_device *mdiodev)
if (id != QCA8K_ID_QCA8337)
return -ENODEV;
- priv->ds = dsa_switch_alloc(&mdiodev->dev, QCA8K_NUM_PORTS);
+ priv->ds = devm_kzalloc(&mdiodev->dev, sizeof(*priv->ds),
+ QCA8K_NUM_PORTS);
if (!priv->ds)
return -ENOMEM;
+ priv->ds->dev = &mdiodev->dev;
+ priv->ds->num_ports = DSA_MAX_PORTS;
priv->ds->priv = priv;
priv->ops = qca8k_switch_ops;
priv->ds->ops = &priv->ops;
diff --git a/drivers/net/dsa/realtek-smi-core.c b/drivers/net/dsa/realtek-smi-core.c
index dc0509c02d29..fae188c60191 100644
--- a/drivers/net/dsa/realtek-smi-core.c
+++ b/drivers/net/dsa/realtek-smi-core.c
@@ -444,9 +444,12 @@ static int realtek_smi_probe(struct platform_device *pdev)
return ret;
}
- smi->ds = dsa_switch_alloc(dev, smi->num_ports);
+ smi->ds = devm_kzalloc(dev, sizeof(*smi->ds), GFP_KERNEL);
if (!smi->ds)
return -ENOMEM;
+
+ smi->ds->dev = dev;
+ smi->ds->num_ports = smi->num_ports;
smi->ds->priv = smi;
smi->ds->ops = var->ds_ops;
diff --git a/drivers/net/dsa/sja1105/sja1105_main.c b/drivers/net/dsa/sja1105/sja1105_main.c
index 0ebbda5ca665..2ae84a9dea59 100644
--- a/drivers/net/dsa/sja1105/sja1105_main.c
+++ b/drivers/net/dsa/sja1105/sja1105_main.c
@@ -2047,10 +2047,12 @@ static int sja1105_probe(struct spi_device *spi)
dev_info(dev, "Probed switch chip: %s\n", priv->info->name);
- ds = dsa_switch_alloc(dev, SJA1105_NUM_PORTS);
+ ds = devm_kzalloc(dev, sizeof(*ds), GFP_KERNEL);
if (!ds)
return -ENOMEM;
+ ds->dev = dev;
+ ds->num_ports = SJA1105_NUM_PORTS;
ds->ops = &sja1105_switch_ops;
ds->priv = priv;
priv->ds = ds;
diff --git a/drivers/net/dsa/vitesse-vsc73xx-core.c b/drivers/net/dsa/vitesse-vsc73xx-core.c
index 614377ef7956..42c1574d45f2 100644
--- a/drivers/net/dsa/vitesse-vsc73xx-core.c
+++ b/drivers/net/dsa/vitesse-vsc73xx-core.c
@@ -1178,9 +1178,12 @@ int vsc73xx_probe(struct vsc73xx *vsc)
* We allocate 8 ports and avoid access to the nonexistant
* ports.
*/
- vsc->ds = dsa_switch_alloc(dev, 8);
+ vsc->ds = devm_kzalloc(dev, sizeof(*vsc->ds), GFP_KERNEL);
if (!vsc->ds)
return -ENOMEM;
+
+ vsc->ds->dev = dev;
+ vsc->ds->num_ports = 8;
vsc->ds->priv = vsc;
vsc->ds->ops = &vsc73xx_ds_ops;
diff --git a/include/net/dsa.h b/include/net/dsa.h
index 9bc1d3f71f89..e3c14dc3bab9 100644
--- a/include/net/dsa.h
+++ b/include/net/dsa.h
@@ -577,7 +577,6 @@ static inline bool dsa_can_decode(const struct sk_buff *skb,
return false;
}
-struct dsa_switch *dsa_switch_alloc(struct device *dev, size_t n);
void dsa_unregister_switch(struct dsa_switch *ds);
int dsa_register_switch(struct dsa_switch *ds);
#ifdef CONFIG_PM_SLEEP
diff --git a/net/dsa/dsa2.c b/net/dsa/dsa2.c
index 83cba4623698..1e3ac9b56c89 100644
--- a/net/dsa/dsa2.c
+++ b/net/dsa/dsa2.c
@@ -846,6 +846,12 @@ static int dsa_switch_probe(struct dsa_switch *ds)
struct device_node *np = ds->dev->of_node;
int err;
+ if (!ds->dev)
+ return -ENODEV;
+
+ if (!ds->num_ports)
+ return -EINVAL;
+
if (np)
err = dsa_switch_parse_of(ds, np);
else if (pdata)
@@ -859,21 +865,6 @@ static int dsa_switch_probe(struct dsa_switch *ds)
return dsa_switch_add(ds);
}
-struct dsa_switch *dsa_switch_alloc(struct device *dev, size_t n)
-{
- struct dsa_switch *ds;
-
- ds = devm_kzalloc(dev, sizeof(*ds), GFP_KERNEL);
- if (!ds)
- return NULL;
-
- ds->dev = dev;
- ds->num_ports = n;
-
- return ds;
-}
-EXPORT_SYMBOL_GPL(dsa_switch_alloc);
-
int dsa_register_switch(struct dsa_switch *ds)
{
int err;
--
2.23.0
Like the dsa_switch_tree structures, the dsa_port structures will be
allocated on switch registration.
The SJA1105 driver is the only one accessing the dsa_port structure
after the switch allocation and before the switch registration.
For that reason, move switch registration prior to assigning the priv
member of the dsa_port structures.
Signed-off-by: Vivien Didelot <[email protected]>
---
drivers/net/dsa/sja1105/sja1105_main.c | 15 ++++++++++-----
1 file changed, 10 insertions(+), 5 deletions(-)
diff --git a/drivers/net/dsa/sja1105/sja1105_main.c b/drivers/net/dsa/sja1105/sja1105_main.c
index 4b0cb779f187..0ebbda5ca665 100644
--- a/drivers/net/dsa/sja1105/sja1105_main.c
+++ b/drivers/net/dsa/sja1105/sja1105_main.c
@@ -2057,6 +2057,15 @@ static int sja1105_probe(struct spi_device *spi)
tagger_data = &priv->tagger_data;
+ mutex_init(&priv->ptp_data.lock);
+ mutex_init(&priv->mgmt_lock);
+
+ sja1105_tas_setup(ds);
+
+ rc = dsa_register_switch(priv->ds);
+ if (rc)
+ return rc;
+
/* Connections between dsa_port and sja1105_port */
for (i = 0; i < SJA1105_NUM_PORTS; i++) {
struct sja1105_port *sp = &priv->ports[i];
@@ -2065,12 +2074,8 @@ static int sja1105_probe(struct spi_device *spi)
sp->dp = dsa_to_port(ds, i);
sp->data = tagger_data;
}
- mutex_init(&priv->ptp_data.lock);
- mutex_init(&priv->mgmt_lock);
- sja1105_tas_setup(ds);
-
- return dsa_register_switch(priv->ds);
+ return 0;
}
static int sja1105_remove(struct spi_device *spi)
--
2.23.0
Since mv88e6xxx_pvt_map is a static helper, no need to return
-EOPNOTSUPP if the chip has no PVT, simply silently skip the operation.
Signed-off-by: Vivien Didelot <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
---
drivers/net/dsa/mv88e6xxx/chip.c | 11 +----------
1 file changed, 1 insertion(+), 10 deletions(-)
diff --git a/drivers/net/dsa/mv88e6xxx/chip.c b/drivers/net/dsa/mv88e6xxx/chip.c
index d67deec77452..510ccdc2d03c 100644
--- a/drivers/net/dsa/mv88e6xxx/chip.c
+++ b/drivers/net/dsa/mv88e6xxx/chip.c
@@ -1253,7 +1253,7 @@ static int mv88e6xxx_pvt_map(struct mv88e6xxx_chip *chip, int dev, int port)
u16 pvlan = 0;
if (!mv88e6xxx_has_pvt(chip))
- return -EOPNOTSUPP;
+ return 0;
/* Skip the local source device, which uses in-chip port VLAN */
if (dev != chip->ds->index)
@@ -2049,9 +2049,6 @@ static int mv88e6xxx_bridge_map(struct mv88e6xxx_chip *chip,
}
}
- if (!mv88e6xxx_has_pvt(chip))
- return 0;
-
/* Remap the Port VLAN of each cross-chip bridge group member */
for (dev = 0; dev < DSA_MAX_SWITCHES; ++dev) {
ds = chip->ds->dst->ds[dev];
@@ -2101,9 +2098,6 @@ static int mv88e6xxx_crosschip_bridge_join(struct dsa_switch *ds, int dev,
struct mv88e6xxx_chip *chip = ds->priv;
int err;
- if (!mv88e6xxx_has_pvt(chip))
- return 0;
-
mv88e6xxx_reg_lock(chip);
err = mv88e6xxx_pvt_map(chip, dev, port);
mv88e6xxx_reg_unlock(chip);
@@ -2116,9 +2110,6 @@ static void mv88e6xxx_crosschip_bridge_leave(struct dsa_switch *ds, int dev,
{
struct mv88e6xxx_chip *chip = ds->priv;
- if (!mv88e6xxx_has_pvt(chip))
- return;
-
mv88e6xxx_reg_lock(chip);
if (mv88e6xxx_pvt_map(chip, dev, port))
dev_err(ds->dev, "failed to remap cross-chip Port VLAN\n");
--
2.23.0
Do not let the drivers access the ds->ports static array directly
while there is a dsa_to_port helper for this purpose.
At the same time, un-const this helper since the SJA1105 driver
assigns the priv member of the returned dsa_port structure.
Signed-off-by: Vivien Didelot <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
---
drivers/net/dsa/b53/b53_common.c | 6 +++---
drivers/net/dsa/bcm_sf2.c | 8 ++++----
drivers/net/dsa/bcm_sf2_cfp.c | 6 +++---
drivers/net/dsa/mt7530.c | 12 ++++++------
drivers/net/dsa/mv88e6xxx/chip.c | 10 +++++-----
drivers/net/dsa/qca8k.c | 2 +-
drivers/net/dsa/sja1105/sja1105_main.c | 18 +++++++++---------
include/net/dsa.h | 2 +-
net/dsa/dsa.c | 8 +++++---
net/dsa/dsa2.c | 4 ++--
net/dsa/switch.c | 4 ++--
net/dsa/tag_8021q.c | 6 +++---
12 files changed, 44 insertions(+), 42 deletions(-)
diff --git a/drivers/net/dsa/b53/b53_common.c b/drivers/net/dsa/b53/b53_common.c
index cc3536315eff..aef9b56781ef 100644
--- a/drivers/net/dsa/b53/b53_common.c
+++ b/drivers/net/dsa/b53/b53_common.c
@@ -524,7 +524,7 @@ int b53_enable_port(struct dsa_switch *ds, int port, struct phy_device *phy)
if (!dsa_is_user_port(ds, port))
return 0;
- cpu_port = ds->ports[port].cpu_dp->index;
+ cpu_port = dsa_to_port(ds, port)->cpu_dp->index;
if (dev->ops->irq_enable)
ret = dev->ops->irq_enable(dev, port);
@@ -1629,7 +1629,7 @@ EXPORT_SYMBOL(b53_fdb_dump);
int b53_br_join(struct dsa_switch *ds, int port, struct net_device *br)
{
struct b53_device *dev = ds->priv;
- s8 cpu_port = ds->ports[port].cpu_dp->index;
+ s8 cpu_port = dsa_to_port(ds, port)->cpu_dp->index;
u16 pvlan, reg;
unsigned int i;
@@ -1675,7 +1675,7 @@ void b53_br_leave(struct dsa_switch *ds, int port, struct net_device *br)
{
struct b53_device *dev = ds->priv;
struct b53_vlan *vl = &dev->vlans[0];
- s8 cpu_port = ds->ports[port].cpu_dp->index;
+ s8 cpu_port = dsa_to_port(ds, port)->cpu_dp->index;
unsigned int i;
u16 pvlan, reg, pvid;
diff --git a/drivers/net/dsa/bcm_sf2.c b/drivers/net/dsa/bcm_sf2.c
index 26509fa37a50..c068a3b7207b 100644
--- a/drivers/net/dsa/bcm_sf2.c
+++ b/drivers/net/dsa/bcm_sf2.c
@@ -662,7 +662,7 @@ static void bcm_sf2_sw_fixed_state(struct dsa_switch *ds, int port,
* state machine and make it go in PHY_FORCING state instead.
*/
if (!status->link)
- netif_carrier_off(ds->ports[port].slave);
+ netif_carrier_off(dsa_to_port(ds, port)->slave);
status->duplex = DUPLEX_FULL;
} else {
status->link = true;
@@ -728,7 +728,7 @@ static int bcm_sf2_sw_resume(struct dsa_switch *ds)
static void bcm_sf2_sw_get_wol(struct dsa_switch *ds, int port,
struct ethtool_wolinfo *wol)
{
- struct net_device *p = ds->ports[port].cpu_dp->master;
+ struct net_device *p = dsa_to_port(ds, port)->cpu_dp->master;
struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
struct ethtool_wolinfo pwol = { };
@@ -752,9 +752,9 @@ static void bcm_sf2_sw_get_wol(struct dsa_switch *ds, int port,
static int bcm_sf2_sw_set_wol(struct dsa_switch *ds, int port,
struct ethtool_wolinfo *wol)
{
- struct net_device *p = ds->ports[port].cpu_dp->master;
+ struct net_device *p = dsa_to_port(ds, port)->cpu_dp->master;
struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
- s8 cpu_port = ds->ports[port].cpu_dp->index;
+ s8 cpu_port = dsa_to_port(ds, port)->cpu_dp->index;
struct ethtool_wolinfo pwol = { };
if (p->ethtool_ops->get_wol)
diff --git a/drivers/net/dsa/bcm_sf2_cfp.c b/drivers/net/dsa/bcm_sf2_cfp.c
index d264776a95a3..f3f0c3f07391 100644
--- a/drivers/net/dsa/bcm_sf2_cfp.c
+++ b/drivers/net/dsa/bcm_sf2_cfp.c
@@ -821,7 +821,7 @@ static int bcm_sf2_cfp_rule_insert(struct dsa_switch *ds, int port,
struct ethtool_rx_flow_spec *fs)
{
struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
- s8 cpu_port = ds->ports[port].cpu_dp->index;
+ s8 cpu_port = dsa_to_port(ds, port)->cpu_dp->index;
__u64 ring_cookie = fs->ring_cookie;
unsigned int queue_num, port_num;
int ret;
@@ -1049,7 +1049,7 @@ static int bcm_sf2_cfp_rule_get_all(struct bcm_sf2_priv *priv,
int bcm_sf2_get_rxnfc(struct dsa_switch *ds, int port,
struct ethtool_rxnfc *nfc, u32 *rule_locs)
{
- struct net_device *p = ds->ports[port].cpu_dp->master;
+ struct net_device *p = dsa_to_port(ds, port)->cpu_dp->master;
struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
int ret = 0;
@@ -1092,7 +1092,7 @@ int bcm_sf2_get_rxnfc(struct dsa_switch *ds, int port,
int bcm_sf2_set_rxnfc(struct dsa_switch *ds, int port,
struct ethtool_rxnfc *nfc)
{
- struct net_device *p = ds->ports[port].cpu_dp->master;
+ struct net_device *p = dsa_to_port(ds, port)->cpu_dp->master;
struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
int ret = 0;
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 1d8d36de4d20..a91293e47a57 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -862,7 +862,7 @@ mt7530_port_set_vlan_unaware(struct dsa_switch *ds, int port)
for (i = 0; i < MT7530_NUM_PORTS; i++) {
if (dsa_is_user_port(ds, i) &&
- dsa_port_is_vlan_filtering(&ds->ports[i])) {
+ dsa_port_is_vlan_filtering(dsa_to_port(ds, i))) {
all_user_ports_removed = false;
break;
}
@@ -922,7 +922,7 @@ mt7530_port_bridge_leave(struct dsa_switch *ds, int port,
* other port is still a VLAN-aware port.
*/
if (dsa_is_user_port(ds, i) && i != port &&
- !dsa_port_is_vlan_filtering(&ds->ports[i])) {
+ !dsa_port_is_vlan_filtering(dsa_to_port(ds, i))) {
if (dsa_to_port(ds, i)->bridge_dev != bridge)
continue;
if (priv->ports[i].enable)
@@ -1165,7 +1165,7 @@ mt7530_port_vlan_add(struct dsa_switch *ds, int port,
/* The port is kept as VLAN-unaware if bridge with vlan_filtering not
* being set.
*/
- if (!dsa_port_is_vlan_filtering(&ds->ports[port]))
+ if (!dsa_port_is_vlan_filtering(dsa_to_port(ds, port)))
return;
mutex_lock(&priv->reg_mutex);
@@ -1196,7 +1196,7 @@ mt7530_port_vlan_del(struct dsa_switch *ds, int port,
/* The port is kept as VLAN-unaware if bridge with vlan_filtering not
* being set.
*/
- if (!dsa_port_is_vlan_filtering(&ds->ports[port]))
+ if (!dsa_port_is_vlan_filtering(dsa_to_port(ds, port)))
return 0;
mutex_lock(&priv->reg_mutex);
@@ -1252,7 +1252,7 @@ mt7530_setup(struct dsa_switch *ds)
* controller also is the container for two GMACs nodes representing
* as two netdev instances.
*/
- dn = ds->ports[MT7530_CPU_PORT].master->dev.of_node->parent;
+ dn = dsa_to_port(ds, MT7530_CPU_PORT)->master->dev.of_node->parent;
if (priv->id == ID_MT7530) {
priv->ethernet = syscon_node_to_regmap(dn);
@@ -1340,7 +1340,7 @@ mt7530_setup(struct dsa_switch *ds)
if (!dsa_is_unused_port(ds, 5)) {
priv->p5_intf_sel = P5_INTF_SEL_GMAC5;
- interface = of_get_phy_mode(ds->ports[5].dn);
+ interface = of_get_phy_mode(dsa_to_port(ds, 5)->dn);
} else {
/* Scan the ethernet nodes. look for GMAC1, lookup used phy */
for_each_child_of_node(dn, mac_np) {
diff --git a/drivers/net/dsa/mv88e6xxx/chip.c b/drivers/net/dsa/mv88e6xxx/chip.c
index 6787d560e9e3..d67deec77452 100644
--- a/drivers/net/dsa/mv88e6xxx/chip.c
+++ b/drivers/net/dsa/mv88e6xxx/chip.c
@@ -1075,7 +1075,7 @@ static u16 mv88e6xxx_port_vlan(struct mv88e6xxx_chip *chip, int dev, int port)
if (dsa_is_cpu_port(ds, port) || dsa_is_dsa_port(ds, port))
return mv88e6xxx_port_mask(chip);
- br = ds->ports[port].bridge_dev;
+ br = dsa_to_port(ds, port)->bridge_dev;
pvlan = 0;
/* Frames from user ports can egress any local DSA links and CPU ports,
@@ -1402,7 +1402,7 @@ static int mv88e6xxx_port_check_hw_vlan(struct dsa_switch *ds, int port,
if (dsa_is_dsa_port(ds, i) || dsa_is_cpu_port(ds, i))
continue;
- if (!ds->ports[i].slave)
+ if (!dsa_to_port(ds, i)->slave)
continue;
if (vlan.member[i] ==
@@ -1410,7 +1410,7 @@ static int mv88e6xxx_port_check_hw_vlan(struct dsa_switch *ds, int port,
continue;
if (dsa_to_port(ds, i)->bridge_dev ==
- ds->ports[port].bridge_dev)
+ dsa_to_port(ds, port)->bridge_dev)
break; /* same bridge, check next VLAN */
if (!dsa_to_port(ds, i)->bridge_dev)
@@ -2042,7 +2042,7 @@ static int mv88e6xxx_bridge_map(struct mv88e6xxx_chip *chip,
/* Remap the Port VLAN of each local bridge group member */
for (port = 0; port < mv88e6xxx_num_ports(chip); ++port) {
- if (chip->ds->ports[port].bridge_dev == br) {
+ if (dsa_to_port(chip->ds, port)->bridge_dev == br) {
err = mv88e6xxx_port_vlan_map(chip, port);
if (err)
return err;
@@ -2059,7 +2059,7 @@ static int mv88e6xxx_bridge_map(struct mv88e6xxx_chip *chip,
break;
for (port = 0; port < ds->num_ports; ++port) {
- if (ds->ports[port].bridge_dev == br) {
+ if (dsa_to_port(ds, port)->bridge_dev == br) {
err = mv88e6xxx_pvt_map(chip, dev, port);
if (err)
return err;
diff --git a/drivers/net/dsa/qca8k.c b/drivers/net/dsa/qca8k.c
index b00274caae4f..71e44c8763b8 100644
--- a/drivers/net/dsa/qca8k.c
+++ b/drivers/net/dsa/qca8k.c
@@ -661,7 +661,7 @@ qca8k_setup(struct dsa_switch *ds)
return ret;
/* Initialize CPU port pad mode (xMII type, delays...) */
- phy_mode = of_get_phy_mode(ds->ports[QCA8K_CPU_PORT].dn);
+ phy_mode = of_get_phy_mode(dsa_to_port(ds, QCA8K_CPU_PORT)->dn);
if (phy_mode < 0) {
pr_err("Can't find phy-mode for master device\n");
return phy_mode;
diff --git a/drivers/net/dsa/sja1105/sja1105_main.c b/drivers/net/dsa/sja1105/sja1105_main.c
index 2ffe642cf54b..4b0cb779f187 100644
--- a/drivers/net/dsa/sja1105/sja1105_main.c
+++ b/drivers/net/dsa/sja1105/sja1105_main.c
@@ -1058,7 +1058,7 @@ int sja1105pqrs_fdb_add(struct dsa_switch *ds, int port,
l2_lookup.vlanid = vid;
l2_lookup.iotag = SJA1105_S_TAG;
l2_lookup.mask_macaddr = GENMASK_ULL(ETH_ALEN * 8 - 1, 0);
- if (dsa_port_is_vlan_filtering(&ds->ports[port])) {
+ if (dsa_port_is_vlan_filtering(dsa_to_port(ds, port))) {
l2_lookup.mask_vlanid = VLAN_VID_MASK;
l2_lookup.mask_iotag = BIT(0);
} else {
@@ -1121,7 +1121,7 @@ int sja1105pqrs_fdb_del(struct dsa_switch *ds, int port,
l2_lookup.vlanid = vid;
l2_lookup.iotag = SJA1105_S_TAG;
l2_lookup.mask_macaddr = GENMASK_ULL(ETH_ALEN * 8 - 1, 0);
- if (dsa_port_is_vlan_filtering(&ds->ports[port])) {
+ if (dsa_port_is_vlan_filtering(dsa_to_port(ds, port))) {
l2_lookup.mask_vlanid = VLAN_VID_MASK;
l2_lookup.mask_iotag = BIT(0);
} else {
@@ -1167,7 +1167,7 @@ static int sja1105_fdb_add(struct dsa_switch *ds, int port,
* for what gets printed in 'bridge fdb show'. In the case of zero,
* no VID gets printed at all.
*/
- if (!dsa_port_is_vlan_filtering(&ds->ports[port]))
+ if (!dsa_port_is_vlan_filtering(dsa_to_port(ds, port)))
vid = 0;
return priv->info->fdb_add_cmd(ds, port, addr, vid);
@@ -1178,7 +1178,7 @@ static int sja1105_fdb_del(struct dsa_switch *ds, int port,
{
struct sja1105_private *priv = ds->priv;
- if (!dsa_port_is_vlan_filtering(&ds->ports[port]))
+ if (!dsa_port_is_vlan_filtering(dsa_to_port(ds, port)))
vid = 0;
return priv->info->fdb_del_cmd(ds, port, addr, vid);
@@ -1217,7 +1217,7 @@ static int sja1105_fdb_dump(struct dsa_switch *ds, int port,
u64_to_ether_addr(l2_lookup.macaddr, macaddr);
/* We need to hide the dsa_8021q VLANs from the user. */
- if (!dsa_port_is_vlan_filtering(&ds->ports[port]))
+ if (!dsa_port_is_vlan_filtering(dsa_to_port(ds, port)))
l2_lookup.vlanid = 0;
cb(macaddr, l2_lookup.vlanid, l2_lookup.lockeds, data);
}
@@ -1704,7 +1704,7 @@ static int sja1105_port_enable(struct dsa_switch *ds, int port,
if (!dsa_is_user_port(ds, port))
return 0;
- slave = ds->ports[port].slave;
+ slave = dsa_to_port(ds, port)->slave;
slave->features &= ~NETIF_F_HW_VLAN_CTAG_FILTER;
@@ -1736,7 +1736,7 @@ static int sja1105_mgmt_xmit(struct dsa_switch *ds, int port, int slot,
}
/* Transfer skb to the host port. */
- dsa_enqueue_skb(skb, ds->ports[port].slave);
+ dsa_enqueue_skb(skb, dsa_to_port(ds, port)->slave);
/* Wait until the switch has processed the frame */
do {
@@ -2061,8 +2061,8 @@ static int sja1105_probe(struct spi_device *spi)
for (i = 0; i < SJA1105_NUM_PORTS; i++) {
struct sja1105_port *sp = &priv->ports[i];
- ds->ports[i].priv = sp;
- sp->dp = &ds->ports[i];
+ dsa_to_port(ds, i)->priv = sp;
+ sp->dp = dsa_to_port(ds, i);
sp->data = tagger_data;
}
mutex_init(&priv->ptp_data.lock);
diff --git a/include/net/dsa.h b/include/net/dsa.h
index 8c3ea0530f65..2e4fe2f8962b 100644
--- a/include/net/dsa.h
+++ b/include/net/dsa.h
@@ -278,7 +278,7 @@ struct dsa_switch {
struct dsa_port ports[];
};
-static inline const struct dsa_port *dsa_to_port(struct dsa_switch *ds, int p)
+static inline struct dsa_port *dsa_to_port(struct dsa_switch *ds, int p)
{
return &ds->ports[p];
}
diff --git a/net/dsa/dsa.c b/net/dsa/dsa.c
index 43120a3fb06f..a5545762f5e7 100644
--- a/net/dsa/dsa.c
+++ b/net/dsa/dsa.c
@@ -246,7 +246,9 @@ static int dsa_switch_rcv(struct sk_buff *skb, struct net_device *dev,
#ifdef CONFIG_PM_SLEEP
static bool dsa_is_port_initialized(struct dsa_switch *ds, int p)
{
- return dsa_is_user_port(ds, p) && ds->ports[p].slave;
+ const struct dsa_port *dp = dsa_to_port(ds, p);
+
+ return dp->type == DSA_PORT_TYPE_USER && dp->slave;
}
int dsa_switch_suspend(struct dsa_switch *ds)
@@ -258,7 +260,7 @@ int dsa_switch_suspend(struct dsa_switch *ds)
if (!dsa_is_port_initialized(ds, i))
continue;
- ret = dsa_slave_suspend(ds->ports[i].slave);
+ ret = dsa_slave_suspend(dsa_to_port(ds, i)->slave);
if (ret)
return ret;
}
@@ -285,7 +287,7 @@ int dsa_switch_resume(struct dsa_switch *ds)
if (!dsa_is_port_initialized(ds, i))
continue;
- ret = dsa_slave_resume(ds->ports[i].slave);
+ ret = dsa_slave_resume(dsa_to_port(ds, i)->slave);
if (ret)
return ret;
}
diff --git a/net/dsa/dsa2.c b/net/dsa/dsa2.c
index 716d265ba8ca..1716535167ee 100644
--- a/net/dsa/dsa2.c
+++ b/net/dsa/dsa2.c
@@ -708,7 +708,7 @@ static int dsa_switch_parse_ports_of(struct dsa_switch *ds,
goto out_put_node;
}
- dp = &ds->ports[reg];
+ dp = dsa_to_port(ds, reg);
err = dsa_port_parse_of(dp, port);
if (err)
@@ -787,7 +787,7 @@ static int dsa_switch_parse_ports(struct dsa_switch *ds,
for (i = 0; i < DSA_MAX_PORTS; i++) {
name = cd->port_names[i];
dev = cd->netdev[i];
- dp = &ds->ports[i];
+ dp = dsa_to_port(ds, i);
if (!name)
continue;
diff --git a/net/dsa/switch.c b/net/dsa/switch.c
index 6a9607518823..df4abe897ed6 100644
--- a/net/dsa/switch.c
+++ b/net/dsa/switch.c
@@ -20,7 +20,7 @@ static unsigned int dsa_switch_fastest_ageing_time(struct dsa_switch *ds,
int i;
for (i = 0; i < ds->num_ports; ++i) {
- struct dsa_port *dp = &ds->ports[i];
+ struct dsa_port *dp = dsa_to_port(ds, i);
if (dp->ageing_time && dp->ageing_time < ageing_time)
ageing_time = dp->ageing_time;
@@ -98,7 +98,7 @@ static int dsa_switch_bridge_leave(struct dsa_switch *ds,
if (unset_vlan_filtering) {
struct switchdev_trans trans = {0};
- err = dsa_port_vlan_filtering(&ds->ports[info->port],
+ err = dsa_port_vlan_filtering(dsa_to_port(ds, info->port),
false, &trans);
if (err && err != EOPNOTSUPP)
return err;
diff --git a/net/dsa/tag_8021q.c b/net/dsa/tag_8021q.c
index 9c1cc2482b68..bf91fc55fc44 100644
--- a/net/dsa/tag_8021q.c
+++ b/net/dsa/tag_8021q.c
@@ -103,7 +103,7 @@ static int dsa_8021q_restore_pvid(struct dsa_switch *ds, int port)
if (!dsa_is_user_port(ds, port))
return 0;
- slave = ds->ports[port].slave;
+ slave = dsa_to_port(ds, port)->slave;
err = br_vlan_get_pvid(slave, &pvid);
if (err < 0)
@@ -118,7 +118,7 @@ static int dsa_8021q_restore_pvid(struct dsa_switch *ds, int port)
return err;
}
- return dsa_port_vid_add(&ds->ports[port], pvid, vinfo.flags);
+ return dsa_port_vid_add(dsa_to_port(ds, port), pvid, vinfo.flags);
}
/* If @enabled is true, installs @vid with @flags into the switch port's HW
@@ -130,7 +130,7 @@ static int dsa_8021q_restore_pvid(struct dsa_switch *ds, int port)
static int dsa_8021q_vid_apply(struct dsa_switch *ds, int port, u16 vid,
u16 flags, bool enabled)
{
- struct dsa_port *dp = &ds->ports[port];
+ struct dsa_port *dp = dsa_to_port(ds, port);
struct bridge_vlan_info vinfo;
int err;
--
2.23.0
Add a list of switch ports within the switch fabric. This will help the
lookup of a port inside the whole fabric, and it is the first step
towards supporting multiple CPU ports, before deprecating the usage of
the unique dst->cpu_dp pointer.
In preparation for a future allocation of the dsa_port structures,
return -ENOMEM in case no structure is returned, even though this
error cannot be reached yet.
Signed-off-by: Vivien Didelot <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
---
include/net/dsa.h | 5 +++++
net/dsa/dsa2.c | 48 +++++++++++++++++++++++++++++++++++++++++------
2 files changed, 47 insertions(+), 6 deletions(-)
diff --git a/include/net/dsa.h b/include/net/dsa.h
index 2e4fe2f8962b..6ff6dfcdc61d 100644
--- a/include/net/dsa.h
+++ b/include/net/dsa.h
@@ -125,6 +125,9 @@ struct dsa_switch_tree {
*/
struct dsa_port *cpu_dp;
+ /* List of switch ports */
+ struct list_head ports;
+
/*
* Data for the individual switch chips.
*/
@@ -195,6 +198,8 @@ struct dsa_port {
struct work_struct xmit_work;
struct sk_buff_head xmit_queue;
+ struct list_head list;
+
/*
* Give the switch driver somewhere to hang its per-port private data
* structures (accessible from the tagger).
diff --git a/net/dsa/dsa2.c b/net/dsa/dsa2.c
index 1716535167ee..ba27ff8b4445 100644
--- a/net/dsa/dsa2.c
+++ b/net/dsa/dsa2.c
@@ -45,6 +45,8 @@ static struct dsa_switch_tree *dsa_tree_alloc(int index)
dst->index = index;
+ INIT_LIST_HEAD(&dst->ports);
+
INIT_LIST_HEAD(&dst->list);
list_add_tail(&dst->list, &dsa_tree_list);
@@ -616,6 +618,22 @@ static int dsa_tree_add_switch(struct dsa_switch_tree *dst,
return err;
}
+static struct dsa_port *dsa_port_touch(struct dsa_switch *ds, int index)
+{
+ struct dsa_switch_tree *dst = ds->dst;
+ struct dsa_port *dp;
+
+ dp = &ds->ports[index];
+
+ dp->ds = ds;
+ dp->index = index;
+
+ INIT_LIST_HEAD(&dp->list);
+ list_add_tail(&dp->list, &dst->ports);
+
+ return dp;
+}
+
static int dsa_port_parse_user(struct dsa_port *dp, const char *name)
{
if (!name)
@@ -742,6 +760,20 @@ static int dsa_switch_parse_member_of(struct dsa_switch *ds,
return 0;
}
+static int dsa_switch_touch_ports(struct dsa_switch *ds)
+{
+ struct dsa_port *dp;
+ int port;
+
+ for (port = 0; port < ds->num_ports; port++) {
+ dp = dsa_port_touch(ds, port);
+ if (!dp)
+ return -ENOMEM;
+ }
+
+ return 0;
+}
+
static int dsa_switch_parse_of(struct dsa_switch *ds, struct device_node *dn)
{
int err;
@@ -750,6 +782,10 @@ static int dsa_switch_parse_of(struct dsa_switch *ds, struct device_node *dn)
if (err)
return err;
+ err = dsa_switch_touch_ports(ds);
+ if (err)
+ return err;
+
return dsa_switch_parse_ports_of(ds, dn);
}
@@ -807,6 +843,8 @@ static int dsa_switch_parse_ports(struct dsa_switch *ds,
static int dsa_switch_parse(struct dsa_switch *ds, struct dsa_chip_data *cd)
{
+ int err;
+
ds->cd = cd;
/* We don't support interconnected switches nor multiple trees via
@@ -817,6 +855,10 @@ static int dsa_switch_parse(struct dsa_switch *ds, struct dsa_chip_data *cd)
if (!ds->dst)
return -ENOMEM;
+ err = dsa_switch_touch_ports(ds);
+ if (err)
+ return err;
+
return dsa_switch_parse_ports(ds, cd);
}
@@ -849,7 +891,6 @@ static int dsa_switch_probe(struct dsa_switch *ds)
struct dsa_switch *dsa_switch_alloc(struct device *dev, size_t n)
{
struct dsa_switch *ds;
- int i;
ds = devm_kzalloc(dev, struct_size(ds, ports, n), GFP_KERNEL);
if (!ds)
@@ -858,11 +899,6 @@ struct dsa_switch *dsa_switch_alloc(struct device *dev, size_t n)
ds->dev = dev;
ds->num_ports = n;
- for (i = 0; i < ds->num_ports; ++i) {
- ds->ports[i].index = i;
- ds->ports[i].ds = ds;
- }
-
return ds;
}
EXPORT_SYMBOL_GPL(dsa_switch_alloc);
--
2.23.0
Use the new ports list instead of iterating over switches and their
ports when setting up the default CPU port. Unassign it on teardown.
Now that we can iterate over multiple CPU ports, remove dst->cpu_dp.
At the same time, provide a better error message for CPU-less tree.
Signed-off-by: Vivien Didelot <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
---
include/net/dsa.h | 5 -----
net/dsa/dsa2.c | 33 ++++++++++++---------------------
2 files changed, 12 insertions(+), 26 deletions(-)
diff --git a/include/net/dsa.h b/include/net/dsa.h
index bd08bdee8341..f572134eb5de 100644
--- a/include/net/dsa.h
+++ b/include/net/dsa.h
@@ -120,11 +120,6 @@ struct dsa_switch_tree {
*/
struct dsa_platform_data *pd;
- /*
- * The switch port to which the CPU is attached.
- */
- struct dsa_port *cpu_dp;
-
/* List of switch ports */
struct list_head ports;
diff --git a/net/dsa/dsa2.c b/net/dsa/dsa2.c
index 80191c7702a9..bf8b4e0fcb4f 100644
--- a/net/dsa/dsa2.c
+++ b/net/dsa/dsa2.c
@@ -197,38 +197,29 @@ static struct dsa_port *dsa_tree_find_first_cpu(struct dsa_switch_tree *dst)
static int dsa_tree_setup_default_cpu(struct dsa_switch_tree *dst)
{
- struct dsa_switch *ds;
- struct dsa_port *dp;
- int device, port;
+ struct dsa_port *cpu_dp, *dp;
- /* DSA currently only supports a single CPU port */
- dst->cpu_dp = dsa_tree_find_first_cpu(dst);
- if (!dst->cpu_dp) {
- pr_warn("Tree has no master device\n");
+ cpu_dp = dsa_tree_find_first_cpu(dst);
+ if (!cpu_dp) {
+ pr_err("DSA: tree %d has no CPU port\n", dst->index);
return -EINVAL;
}
/* Assign the default CPU port to all ports of the fabric */
- for (device = 0; device < DSA_MAX_SWITCHES; device++) {
- ds = dst->ds[device];
- if (!ds)
- continue;
-
- for (port = 0; port < ds->num_ports; port++) {
- dp = &ds->ports[port];
-
- if (dsa_port_is_user(dp) || dsa_port_is_dsa(dp))
- dp->cpu_dp = dst->cpu_dp;
- }
- }
+ list_for_each_entry(dp, &dst->ports, list)
+ if (dsa_port_is_user(dp) || dsa_port_is_dsa(dp))
+ dp->cpu_dp = cpu_dp;
return 0;
}
static void dsa_tree_teardown_default_cpu(struct dsa_switch_tree *dst)
{
- /* DSA currently only supports a single CPU port */
- dst->cpu_dp = NULL;
+ struct dsa_port *dp;
+
+ list_for_each_entry(dp, &dst->ports, list)
+ if (dsa_port_is_user(dp) || dsa_port_is_dsa(dp))
+ dp->cpu_dp = NULL;
}
static int dsa_port_setup(struct dsa_port *dp)
--
2.23.0
Instead of digging into the other dsa_switch structures of the fabric
and relying too much on the dsa_to_port helper, use the new list
of switch fabric ports to remap the Port VLAN Map of local bridge
group members or remap the Port VLAN Table entry of external bridge
group members.
Signed-off-by: Vivien Didelot <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
---
drivers/net/dsa/mv88e6xxx/chip.c | 39 +++++++++++++++-----------------
1 file changed, 18 insertions(+), 21 deletions(-)
diff --git a/drivers/net/dsa/mv88e6xxx/chip.c b/drivers/net/dsa/mv88e6xxx/chip.c
index af8943142053..826ae82ed727 100644
--- a/drivers/net/dsa/mv88e6xxx/chip.c
+++ b/drivers/net/dsa/mv88e6xxx/chip.c
@@ -2043,29 +2043,26 @@ static int mv88e6xxx_port_fdb_dump(struct dsa_switch *ds, int port,
static int mv88e6xxx_bridge_map(struct mv88e6xxx_chip *chip,
struct net_device *br)
{
- struct dsa_switch *ds;
- int port;
- int dev;
+ struct dsa_switch *ds = chip->ds;
+ struct dsa_switch_tree *dst = ds->dst;
+ struct dsa_port *dp;
int err;
- /* Remap the Port VLAN of each local bridge group member */
- for (port = 0; port < mv88e6xxx_num_ports(chip); ++port) {
- if (dsa_to_port(chip->ds, port)->bridge_dev == br) {
- err = mv88e6xxx_port_vlan_map(chip, port);
- if (err)
- return err;
- }
- }
-
- /* Remap the Port VLAN of each cross-chip bridge group member */
- for (dev = 0; dev < DSA_MAX_SWITCHES; ++dev) {
- ds = chip->ds->dst->ds[dev];
- if (!ds)
- break;
-
- for (port = 0; port < ds->num_ports; ++port) {
- if (dsa_to_port(ds, port)->bridge_dev == br) {
- err = mv88e6xxx_pvt_map(chip, dev, port);
+ list_for_each_entry(dp, &dst->ports, list) {
+ if (dp->bridge_dev == br) {
+ if (dp->ds == ds) {
+ /* This is a local bridge group member,
+ * remap its Port VLAN Map.
+ */
+ err = mv88e6xxx_port_vlan_map(chip, dp->index);
+ if (err)
+ return err;
+ } else {
+ /* This is an external bridge group member,
+ * remap its cross-chip Port VLAN Table entry.
+ */
+ err = mv88e6xxx_pvt_map(chip, dp->ds->index,
+ dp->index);
if (err)
return err;
}
--
2.23.0
Now that we have a potential list of CPU ports, make use of it instead
of only configuring the master device of an unique CPU port.
Signed-off-by: Vivien Didelot <[email protected]>
---
net/dsa/dsa2.c | 22 +++++++++++++++-------
1 file changed, 15 insertions(+), 7 deletions(-)
diff --git a/net/dsa/dsa2.c b/net/dsa/dsa2.c
index a4de7ff8b19b..514c0195e2e8 100644
--- a/net/dsa/dsa2.c
+++ b/net/dsa/dsa2.c
@@ -493,19 +493,27 @@ static void dsa_tree_teardown_switches(struct dsa_switch_tree *dst)
static int dsa_tree_setup_master(struct dsa_switch_tree *dst)
{
- struct dsa_port *cpu_dp = dst->cpu_dp;
- struct net_device *master = cpu_dp->master;
+ struct dsa_port *dp;
+ int err;
- /* DSA currently supports a single pair of CPU port and master device */
- return dsa_master_setup(master, cpu_dp);
+ list_for_each_entry(dp, &dst->ports, list) {
+ if (dsa_port_is_cpu(dp)) {
+ err = dsa_master_setup(dp->master, dp);
+ if (err)
+ return err;
+ }
+ }
+
+ return 0;
}
static void dsa_tree_teardown_master(struct dsa_switch_tree *dst)
{
- struct dsa_port *cpu_dp = dst->cpu_dp;
- struct net_device *master = cpu_dp->master;
+ struct dsa_port *dp;
- return dsa_master_teardown(master);
+ list_for_each_entry(dp, &dst->ports, list)
+ if (dsa_port_is_cpu(dp))
+ dsa_master_teardown(dp->master);
}
static int dsa_tree_setup(struct dsa_switch_tree *dst)
--
2.23.0
Use the new ports list instead of accessing the dsa_switch array
of ports when iterating over DSA ports of a switch to set up the
routing table.
Signed-off-by: Vivien Didelot <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
---
net/dsa/dsa2.c | 7 +++----
1 file changed, 3 insertions(+), 4 deletions(-)
diff --git a/net/dsa/dsa2.c b/net/dsa/dsa2.c
index 01b6047d9b7b..623805ba8e1a 100644
--- a/net/dsa/dsa2.c
+++ b/net/dsa/dsa2.c
@@ -157,6 +157,7 @@ static bool dsa_port_setup_routing_table(struct dsa_port *dp)
static bool dsa_switch_setup_routing_table(struct dsa_switch *ds)
{
+ struct dsa_switch_tree *dst = ds->dst;
bool complete = true;
struct dsa_port *dp;
int i;
@@ -164,10 +165,8 @@ static bool dsa_switch_setup_routing_table(struct dsa_switch *ds)
for (i = 0; i < DSA_MAX_SWITCHES; i++)
ds->rtable[i] = DSA_RTABLE_NONE;
- for (i = 0; i < ds->num_ports; i++) {
- dp = &ds->ports[i];
-
- if (dsa_port_is_dsa(dp)) {
+ list_for_each_entry(dp, &dst->ports, list) {
+ if (dp->ds == ds && dsa_port_is_dsa(dp)) {
complete = dsa_port_setup_routing_table(dp);
if (!complete)
break;
--
2.23.0
On 10/21/19 1:51 PM, Vivien Didelot wrote:
> The dsa_switch structure represents the physical switch device itself,
> and is allocated by the driver. The dsa_switch_tree and dsa_port structures
> represent the logical switch fabric (eventually composed of multiple switch
> devices) and its ports, and are allocated by the DSA core.
>
> This branch lists the logical ports directly in the fabric which simplifies
> the iteration over all ports when assigning the default CPU port or configuring
> the D in DSA in drivers like mv88e6xxx.
>
> This also removes the unique dst->cpu_dp pointer and is a first step towards
> supporting multiple CPU ports and dropping the DSA_MAX_PORTS limitation.
>
> Because the dsa_port structures are not tight to the dsa_switch structure
> anymore, we do not need to provide an helper for the drivers to allocate a
> switch structure. Like in many other subsystems, drivers can now embed their
> dsa_switch structure as they wish into their private structure. This will
> be particularly interesting for the Broadcom drivers which were currently
> limited by the dynamically allocated array of DSA ports.
>
> The series implements the list of dsa_port structures, makes use of it,
> then drops dst->cpu_dp and the dsa_switch_alloc helper.
For the entire series:
Tested-by: Florian Fainelli <[email protected]>
On a BCM7278 with two CPU ports (one at 5, one at 8), and things are
working as they used to before your patch series, thanks!
--
Florian
On 21. 10. 19 22:51, Vivien Didelot wrote:
> The dsa_switch structure represents the physical switch device itself,
> and is allocated by the driver. The dsa_switch_tree and dsa_port structures
> represent the logical switch fabric (eventually composed of multiple switch
> devices) and its ports, and are allocated by the DSA core.
>
> This branch lists the logical ports directly in the fabric which simplifies
> the iteration over all ports when assigning the default CPU port or configuring
> the D in DSA in drivers like mv88e6xxx.
>
> This also removes the unique dst->cpu_dp pointer and is a first step towards
> supporting multiple CPU ports and dropping the DSA_MAX_PORTS limitation.
>
> Because the dsa_port structures are not tight to the dsa_switch structure
> anymore, we do not need to provide an helper for the drivers to allocate a
> switch structure. Like in many other subsystems, drivers can now embed their
> dsa_switch structure as they wish into their private structure. This will
> be particularly interesting for the Broadcom drivers which were currently
> limited by the dynamically allocated array of DSA ports.
>
> The series implements the list of dsa_port structures, makes use of it,
> then drops dst->cpu_dp and the dsa_switch_alloc helper.
I just tried the whole series on our imx6dl-yapp4-hydra with QCA8334
switch and did not notice any problems as well. Thank you.
Tested-by: Michal Vokáč <[email protected]>
On Mon, 21 Oct 2019 16:51:14 -0400, Vivien Didelot wrote:
> The dsa_switch structure represents the physical switch device itself,
> and is allocated by the driver. The dsa_switch_tree and dsa_port structures
> represent the logical switch fabric (eventually composed of multiple switch
> devices) and its ports, and are allocated by the DSA core.
>
> This branch lists the logical ports directly in the fabric which simplifies
> the iteration over all ports when assigning the default CPU port or configuring
> the D in DSA in drivers like mv88e6xxx.
>
> This also removes the unique dst->cpu_dp pointer and is a first step towards
> supporting multiple CPU ports and dropping the DSA_MAX_PORTS limitation.
>
> Because the dsa_port structures are not tight to the dsa_switch structure
> anymore, we do not need to provide an helper for the drivers to allocate a
> switch structure. Like in many other subsystems, drivers can now embed their
> dsa_switch structure as they wish into their private structure. This will
> be particularly interesting for the Broadcom drivers which were currently
> limited by the dynamically allocated array of DSA ports.
>
> The series implements the list of dsa_port structures, makes use of it,
> then drops dst->cpu_dp and the dsa_switch_alloc helper.
Applied, thanks!