From: Tao Ren <[email protected]>
The patch series adds "bel-pfe" pmbus driver which supports hardware
monitoring for BEL PFE1100 and PFE3000 power supplies.
There are total 3 patches:
- patch #1 adds the initial version of bel-pfe driver which supports
BEL PFE1100 power supply.
- patch #2 adds BEL PFE3000 support into bel-pfe driver.
- patch #3 adds documentation for PFE1100 and PFE3000 chips.
The driver has been tested on Facebook Wedge40 BMC (with PFE1100) and
Facebook CMM BMC (with PFE3000).
Tao Ren (3):
hwmon: (pmbus) add BEL PFE1100 power supply driver
hwmon: (pmbus) add BEL PFE3000 power supply driver
docs: hwmon: Document bel-pfe pmbus driver
Documentation/hwmon/bel-pfe.rst | 112 +++++++++++++++++++++++++++
drivers/hwmon/pmbus/Kconfig | 9 +++
drivers/hwmon/pmbus/Makefile | 1 +
drivers/hwmon/pmbus/bel-pfe.c | 131 ++++++++++++++++++++++++++++++++
4 files changed, 253 insertions(+)
create mode 100644 Documentation/hwmon/bel-pfe.rst
create mode 100644 drivers/hwmon/pmbus/bel-pfe.c
--
2.17.1
From: Tao Ren <[email protected]>
Add documentation for bel-pfe pmbus driver which supports BEL PFE1100 and
PFE3000 power supplies.
Signed-off-by: Tao Ren <[email protected]>
---
Documentation/hwmon/bel-pfe.rst | 112 ++++++++++++++++++++++++++++++++
1 file changed, 112 insertions(+)
create mode 100644 Documentation/hwmon/bel-pfe.rst
diff --git a/Documentation/hwmon/bel-pfe.rst b/Documentation/hwmon/bel-pfe.rst
new file mode 100644
index 000000000000..4b4a7d67854c
--- /dev/null
+++ b/Documentation/hwmon/bel-pfe.rst
@@ -0,0 +1,112 @@
+Kernel driver bel-pfe
+======================
+
+Supported chips:
+
+ * BEL PFE1100
+
+ Prefixes: 'pfe1100'
+
+ Addresses scanned: -
+
+ Datasheet: https://www.belfuse.com/resources/datasheets/powersolutions/ds-bps-pfe1100-12-054xa.pdf
+
+ * BEL PFE3000
+
+ Prefixes: 'pfe3000'
+
+ Addresses scanned: -
+
+ Datasheet: https://www.belfuse.com/resources/datasheets/powersolutions/ds-bps-pfe3000-series.pdf
+
+Author: Tao Ren <[email protected]>
+
+
+Description
+-----------
+
+This driver supports hardware monitoring for below power supply devices
+which support PMBus Protocol:
+
+ * BEL PFE1100
+
+ 1100 Watt AC to DC power-factor-corrected (PFC) power supply.
+ PMBus Communication Manual is not publicly available.
+
+ * BEL PFE3000
+
+ 3000 Watt AC/DC power-factor-corrected (PFC) and DC-DC power supply.
+ PMBus Communication Manual is not publicly available.
+
+The driver is a client driver to the core PMBus driver. Please see
+Documentation/hwmon/pmbus.rst for details on PMBus client drivers.
+
+
+Usage Notes
+-----------
+
+This driver does not auto-detect devices. You will have to instantiate the
+devices explicitly. Please see Documentation/i2c/instantiating-devices.rst for
+details.
+
+Example: the following will load the driver for an PFE3000 at address 0x20
+on I2C bus #1::
+
+ $ modprobe bel-pfe
+ $ echo pfe3000 0x20 > /sys/bus/i2c/devices/i2c-1/new_device
+
+
+Platform data support
+---------------------
+
+The driver supports standard PMBus driver platform data.
+
+
+Sysfs entries
+-------------
+
+======================= =======================================================
+curr1_label "iin"
+curr1_input Measured input current
+curr1_max Input current max value
+curr1_max_alarm Input current max alarm
+
+curr[2-3]_label "iout[1-2]"
+curr[2-3]_input Measured output current
+curr[2-3]_max Output current max value
+curr[2-3]_max_alarm Output current max alarm
+
+fan[1-2]_input Fan 1 and 2 speed in RPM
+fan1_target Set fan speed reference for both fans
+
+in1_label "vin"
+in1_input Measured input voltage
+in1_crit Input voltage critical max value
+in1_crit_alarm Input voltage critical max alarm
+in1_lcrit Input voltage critical min value
+in1_lcrit_alarm Input voltage critical min alarm
+in1_max Input voltage max value
+in1_max_alarm Input voltage max alarm
+
+in2_label "vcap"
+in2_input Hold up capacitor voltage
+
+in[3-8]_label "vout[1-3,5-7]"
+in[3-8]_input Measured output voltage
+in[3-4]_alarm vout[1-2] output voltage alarm
+
+power[1-2]_label "pin[1-2]"
+power[1-2]_input Measured input power
+power[1-2]_alarm Input power high alarm
+
+power[3-4]_label "pout[1-2]"
+power[3-4]_input Measured output power
+
+temp[1-3]_input Measured temperature
+temp[1-3]_alarm Temperature alarm
+======================= =======================================================
+
+.. note::
+
+ - curr3, fan2, vout[2-7], vcap, pin2, pout2 and temp3 attributes only
+ exist for PFE3000.
--
2.17.1
From: Tao Ren <[email protected]>
Add the driver to support BEL PFE1100 which is 1100 Wat AC to DC power
supply. The chip has only 1 page.
Signed-off-by: Tao Ren <[email protected]>
---
drivers/hwmon/pmbus/Kconfig | 9 +++++
drivers/hwmon/pmbus/Makefile | 1 +
drivers/hwmon/pmbus/bel-pfe.c | 68 +++++++++++++++++++++++++++++++++++
3 files changed, 78 insertions(+)
create mode 100644 drivers/hwmon/pmbus/bel-pfe.c
diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
index d62d69bb7e49..59859979571d 100644
--- a/drivers/hwmon/pmbus/Kconfig
+++ b/drivers/hwmon/pmbus/Kconfig
@@ -36,6 +36,15 @@ config SENSORS_ADM1275
This driver can also be built as a module. If so, the module will
be called adm1275.
+config SENSORS_BEL_PFE
+ tristate "Bel PFE Compatible Power Supplies"
+ help
+ If you say yes here you get hardware monitoring support for BEL
+ PFE1100 and PFE3000 Power Supplies.
+
+ This driver can also be built as a module. If so, the module will
+ be called bel-pfe.
+
config SENSORS_IBM_CFFPS
tristate "IBM Common Form Factor Power Supply"
depends on LEDS_CLASS
diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
index 03bacfcfd660..3f8c1014938b 100644
--- a/drivers/hwmon/pmbus/Makefile
+++ b/drivers/hwmon/pmbus/Makefile
@@ -6,6 +6,7 @@
obj-$(CONFIG_PMBUS) += pmbus_core.o
obj-$(CONFIG_SENSORS_PMBUS) += pmbus.o
obj-$(CONFIG_SENSORS_ADM1275) += adm1275.o
+obj-$(CONFIG_SENSORS_BEL_PFE) += bel-pfe.o
obj-$(CONFIG_SENSORS_IBM_CFFPS) += ibm-cffps.o
obj-$(CONFIG_SENSORS_INSPUR_IPSPS) += inspur-ipsps.o
obj-$(CONFIG_SENSORS_IR35221) += ir35221.o
diff --git a/drivers/hwmon/pmbus/bel-pfe.c b/drivers/hwmon/pmbus/bel-pfe.c
new file mode 100644
index 000000000000..117f9af21bf3
--- /dev/null
+++ b/drivers/hwmon/pmbus/bel-pfe.c
@@ -0,0 +1,68 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Hardware monitoring driver for BEL PFE family power supplies.
+ *
+ * Copyright (c) 2019 Facebook Inc.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include "pmbus.h"
+
+enum chips {pfe1100};
+
+static struct pmbus_driver_info pfe_driver_info[] = {
+ [pfe1100] = {
+ .pages = 1,
+ .format[PSC_VOLTAGE_IN] = linear,
+ .format[PSC_VOLTAGE_OUT] = linear,
+ .format[PSC_CURRENT_IN] = linear,
+ .format[PSC_CURRENT_OUT] = linear,
+ .format[PSC_POWER] = linear,
+ .format[PSC_TEMPERATURE] = linear,
+ .format[PSC_FAN] = linear,
+
+ .func[0] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
+ PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
+ PMBUS_HAVE_POUT |
+ PMBUS_HAVE_VIN | PMBUS_HAVE_IIN |
+ PMBUS_HAVE_PIN | PMBUS_HAVE_STATUS_INPUT |
+ PMBUS_HAVE_TEMP | PMBUS_HAVE_TEMP2 |
+ PMBUS_HAVE_STATUS_TEMP |
+ PMBUS_HAVE_FAN12,
+ },
+};
+
+static int pfe_pmbus_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ int model;
+
+ model = (int)id->driver_data;
+ return pmbus_do_probe(client, id, &pfe_driver_info[model]);
+}
+
+static const struct i2c_device_id pfe_device_id[] = {
+ {"pfe1100", pfe1100},
+ {}
+};
+
+MODULE_DEVICE_TABLE(i2c, pfe_device_id);
+
+static struct i2c_driver pfe_pmbus_driver = {
+ .driver = {
+ .name = "bel-pfe",
+ },
+ .probe = pfe_pmbus_probe,
+ .remove = pmbus_do_remove,
+ .id_table = pfe_device_id,
+};
+
+module_i2c_driver(pfe_pmbus_driver);
+
+MODULE_AUTHOR("Tao Ren <[email protected]>");
+MODULE_DESCRIPTION("PMBus driver for BEL PFE Family Power Supplies");
+MODULE_LICENSE("GPL");
--
2.17.1
On Mon, Oct 28, 2019 at 04:49:02PM -0700, [email protected] wrote:
> From: Tao Ren <[email protected]>
>
> Add the driver to support BEL PFE1100 which is 1100 Wat AC to DC power
> supply. The chip has only 1 page.
>
> Signed-off-by: Tao Ren <[email protected]>
Please combine with the next patch.
> ---
> drivers/hwmon/pmbus/Kconfig | 9 +++++
> drivers/hwmon/pmbus/Makefile | 1 +
> drivers/hwmon/pmbus/bel-pfe.c | 68 +++++++++++++++++++++++++++++++++++
> 3 files changed, 78 insertions(+)
> create mode 100644 drivers/hwmon/pmbus/bel-pfe.c
>
> diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
> index d62d69bb7e49..59859979571d 100644
> --- a/drivers/hwmon/pmbus/Kconfig
> +++ b/drivers/hwmon/pmbus/Kconfig
> @@ -36,6 +36,15 @@ config SENSORS_ADM1275
> This driver can also be built as a module. If so, the module will
> be called adm1275.
>
> +config SENSORS_BEL_PFE
> + tristate "Bel PFE Compatible Power Supplies"
> + help
> + If you say yes here you get hardware monitoring support for BEL
> + PFE1100 and PFE3000 Power Supplies.
> +
> + This driver can also be built as a module. If so, the module will
> + be called bel-pfe.
> +
> config SENSORS_IBM_CFFPS
> tristate "IBM Common Form Factor Power Supply"
> depends on LEDS_CLASS
> diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
> index 03bacfcfd660..3f8c1014938b 100644
> --- a/drivers/hwmon/pmbus/Makefile
> +++ b/drivers/hwmon/pmbus/Makefile
> @@ -6,6 +6,7 @@
> obj-$(CONFIG_PMBUS) += pmbus_core.o
> obj-$(CONFIG_SENSORS_PMBUS) += pmbus.o
> obj-$(CONFIG_SENSORS_ADM1275) += adm1275.o
> +obj-$(CONFIG_SENSORS_BEL_PFE) += bel-pfe.o
> obj-$(CONFIG_SENSORS_IBM_CFFPS) += ibm-cffps.o
> obj-$(CONFIG_SENSORS_INSPUR_IPSPS) += inspur-ipsps.o
> obj-$(CONFIG_SENSORS_IR35221) += ir35221.o
> diff --git a/drivers/hwmon/pmbus/bel-pfe.c b/drivers/hwmon/pmbus/bel-pfe.c
> new file mode 100644
> index 000000000000..117f9af21bf3
> --- /dev/null
> +++ b/drivers/hwmon/pmbus/bel-pfe.c
> @@ -0,0 +1,68 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Hardware monitoring driver for BEL PFE family power supplies.
> + *
> + * Copyright (c) 2019 Facebook Inc.
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/init.h>
> +#include <linux/err.h>
> +#include <linux/i2c.h>
Alphabetic include file order, please.
> +#include "pmbus.h"
> +
> +enum chips {pfe1100};
> +
> +static struct pmbus_driver_info pfe_driver_info[] = {
> + [pfe1100] = {
> + .pages = 1,
> + .format[PSC_VOLTAGE_IN] = linear,
> + .format[PSC_VOLTAGE_OUT] = linear,
> + .format[PSC_CURRENT_IN] = linear,
> + .format[PSC_CURRENT_OUT] = linear,
> + .format[PSC_POWER] = linear,
> + .format[PSC_TEMPERATURE] = linear,
> + .format[PSC_FAN] = linear,
> +
> + .func[0] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> + PMBUS_HAVE_POUT |
> + PMBUS_HAVE_VIN | PMBUS_HAVE_IIN |
> + PMBUS_HAVE_PIN | PMBUS_HAVE_STATUS_INPUT |
> + PMBUS_HAVE_TEMP | PMBUS_HAVE_TEMP2 |
> + PMBUS_HAVE_STATUS_TEMP |
> + PMBUS_HAVE_FAN12,
> + },
> +};
> +
> +static int pfe_pmbus_probe(struct i2c_client *client,
> + const struct i2c_device_id *id)
> +{
> + int model;
> +
> + model = (int)id->driver_data;
> + return pmbus_do_probe(client, id, &pfe_driver_info[model]);
> +}
> +
> +static const struct i2c_device_id pfe_device_id[] = {
> + {"pfe1100", pfe1100},
> + {}
> +};
> +
> +MODULE_DEVICE_TABLE(i2c, pfe_device_id);
> +
> +static struct i2c_driver pfe_pmbus_driver = {
> + .driver = {
> + .name = "bel-pfe",
> + },
> + .probe = pfe_pmbus_probe,
> + .remove = pmbus_do_remove,
> + .id_table = pfe_device_id,
> +};
> +
> +module_i2c_driver(pfe_pmbus_driver);
> +
> +MODULE_AUTHOR("Tao Ren <[email protected]>");
> +MODULE_DESCRIPTION("PMBus driver for BEL PFE Family Power Supplies");
> +MODULE_LICENSE("GPL");
On Tue, Oct 29, 2019 at 05:42:55AM -0700, Guenter Roeck wrote:
> On Mon, Oct 28, 2019 at 04:49:02PM -0700, [email protected] wrote:
> > From: Tao Ren <[email protected]>
> >
> > Add the driver to support BEL PFE1100 which is 1100 Wat AC to DC power
> > supply. The chip has only 1 page.
> >
> > Signed-off-by: Tao Ren <[email protected]>
>
> Please combine with the next patch.
Sure. Will combine the 2 patches in v2.
> > ---
> > drivers/hwmon/pmbus/Kconfig | 9 +++++
> > drivers/hwmon/pmbus/Makefile | 1 +
> > drivers/hwmon/pmbus/bel-pfe.c | 68 +++++++++++++++++++++++++++++++++++
> > 3 files changed, 78 insertions(+)
> > create mode 100644 drivers/hwmon/pmbus/bel-pfe.c
> >
> > diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
> > index d62d69bb7e49..59859979571d 100644
> > --- a/drivers/hwmon/pmbus/Kconfig
> > +++ b/drivers/hwmon/pmbus/Kconfig
> > @@ -36,6 +36,15 @@ config SENSORS_ADM1275
> > This driver can also be built as a module. If so, the module will
> > be called adm1275.
> >
> > +config SENSORS_BEL_PFE
> > + tristate "Bel PFE Compatible Power Supplies"
> > + help
> > + If you say yes here you get hardware monitoring support for BEL
> > + PFE1100 and PFE3000 Power Supplies.
> > +
> > + This driver can also be built as a module. If so, the module will
> > + be called bel-pfe.
> > +
> > config SENSORS_IBM_CFFPS
> > tristate "IBM Common Form Factor Power Supply"
> > depends on LEDS_CLASS
> > diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
> > index 03bacfcfd660..3f8c1014938b 100644
> > --- a/drivers/hwmon/pmbus/Makefile
> > +++ b/drivers/hwmon/pmbus/Makefile
> > @@ -6,6 +6,7 @@
> > obj-$(CONFIG_PMBUS) += pmbus_core.o
> > obj-$(CONFIG_SENSORS_PMBUS) += pmbus.o
> > obj-$(CONFIG_SENSORS_ADM1275) += adm1275.o
> > +obj-$(CONFIG_SENSORS_BEL_PFE) += bel-pfe.o
> > obj-$(CONFIG_SENSORS_IBM_CFFPS) += ibm-cffps.o
> > obj-$(CONFIG_SENSORS_INSPUR_IPSPS) += inspur-ipsps.o
> > obj-$(CONFIG_SENSORS_IR35221) += ir35221.o
> > diff --git a/drivers/hwmon/pmbus/bel-pfe.c b/drivers/hwmon/pmbus/bel-pfe.c
> > new file mode 100644
> > index 000000000000..117f9af21bf3
> > --- /dev/null
> > +++ b/drivers/hwmon/pmbus/bel-pfe.c
> > @@ -0,0 +1,68 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Hardware monitoring driver for BEL PFE family power supplies.
> > + *
> > + * Copyright (c) 2019 Facebook Inc.
> > + */
> > +
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include <linux/init.h>
> > +#include <linux/err.h>
> > +#include <linux/i2c.h>
>
> Alphabetic include file order, please.
Got it. Will take care of it in v2.
> > +#include "pmbus.h"
> > +
> > +enum chips {pfe1100};
> > +
> > +static struct pmbus_driver_info pfe_driver_info[] = {
> > + [pfe1100] = {
> > + .pages = 1,
> > + .format[PSC_VOLTAGE_IN] = linear,
> > + .format[PSC_VOLTAGE_OUT] = linear,
> > + .format[PSC_CURRENT_IN] = linear,
> > + .format[PSC_CURRENT_OUT] = linear,
> > + .format[PSC_POWER] = linear,
> > + .format[PSC_TEMPERATURE] = linear,
> > + .format[PSC_FAN] = linear,
> > +
> > + .func[0] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> > + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> > + PMBUS_HAVE_POUT |
> > + PMBUS_HAVE_VIN | PMBUS_HAVE_IIN |
> > + PMBUS_HAVE_PIN | PMBUS_HAVE_STATUS_INPUT |
> > + PMBUS_HAVE_TEMP | PMBUS_HAVE_TEMP2 |
> > + PMBUS_HAVE_STATUS_TEMP |
> > + PMBUS_HAVE_FAN12,
> > + },
> > +};
> > +
> > +static int pfe_pmbus_probe(struct i2c_client *client,
> > + const struct i2c_device_id *id)
> > +{
> > + int model;
> > +
> > + model = (int)id->driver_data;
> > + return pmbus_do_probe(client, id, &pfe_driver_info[model]);
> > +}
> > +
> > +static const struct i2c_device_id pfe_device_id[] = {
> > + {"pfe1100", pfe1100},
> > + {}
> > +};
> > +
> > +MODULE_DEVICE_TABLE(i2c, pfe_device_id);
> > +
> > +static struct i2c_driver pfe_pmbus_driver = {
> > + .driver = {
> > + .name = "bel-pfe",
> > + },
> > + .probe = pfe_pmbus_probe,
> > + .remove = pmbus_do_remove,
> > + .id_table = pfe_device_id,
> > +};
> > +
> > +module_i2c_driver(pfe_pmbus_driver);
> > +
> > +MODULE_AUTHOR("Tao Ren <[email protected]>");
> > +MODULE_DESCRIPTION("PMBus driver for BEL PFE Family Power Supplies");
> > +MODULE_LICENSE("GPL");