2019-12-19 09:22:04

by Michael Kao

[permalink] [raw]
Subject: [PATCH] thermal: mediatek: add suspend/resume callback

From: Louis Yu <[email protected]>

Add suspend/resume callback to disable/enable Mediatek thermal sensor
respectively. Since thermal power domain is off in suspend, thermal driver
needs re-initialization during resume.

Signed-off-by: Louis Yu <[email protected]>
Signed-off-by: Michael Kao <[email protected]>
---
drivers/thermal/mtk_thermal.c | 134 +++++++++++++++++++++++++++++++---
1 file changed, 125 insertions(+), 9 deletions(-)

diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c
index acf4854cbb8b..2bb8b13591aa 100644
--- a/drivers/thermal/mtk_thermal.c
+++ b/drivers/thermal/mtk_thermal.c
@@ -22,6 +22,7 @@
#include <linux/thermal.h>
#include <linux/reset.h>
#include <linux/types.h>
+#include <linux/iopoll.h>

/* AUXADC Registers */
#define AUXADC_CON1_SET_V 0x008
@@ -31,6 +32,8 @@

#define APMIXED_SYS_TS_CON1 0x604

+#define APMIXED_SYS_TS_CON1_BUFFER_OFF 0x30
+
/* Thermal Controller Registers */
#define TEMP_MONCTL0 0x000
#define TEMP_MONCTL1 0x004
@@ -38,6 +41,7 @@
#define TEMP_MONIDET0 0x014
#define TEMP_MONIDET1 0x018
#define TEMP_MSRCTL0 0x038
+#define TEMP_MSRCTL1 0x03c
#define TEMP_AHBPOLL 0x040
#define TEMP_AHBTO 0x044
#define TEMP_ADCPNP0 0x048
@@ -87,6 +91,9 @@
#define TEMP_ADCVALIDMASK_VALID_HIGH BIT(5)
#define TEMP_ADCVALIDMASK_VALID_POS(bit) (bit)

+#define TEMP_MSRCTL1_BUS_STA (BIT(0) | BIT(7))
+#define TEMP_MSRCTL1_SENSING_POINTS_PAUSE 0x10E
+
/* MT8173 thermal sensors */
#define MT8173_TS1 0
#define MT8173_TS2 1
@@ -250,6 +257,10 @@ struct mtk_thermal_data {
struct mtk_thermal {
struct device *dev;
void __iomem *thermal_base;
+ void __iomem *apmixed_base;
+ void __iomem *auxadc_base;
+ u64 apmixed_phys_base;
+ u64 auxadc_phys_base;

struct clk *clk_peri_therm;
struct clk *clk_auxadc;
@@ -746,6 +757,42 @@ static void mtk_thermal_init_bank(struct mtk_thermal *mt, int num,
mtk_thermal_put_bank(bank);
}

+static int mtk_thermal_disable_sensing(struct mtk_thermal *mt, int num)
+{
+ struct mtk_thermal_bank *bank = &mt->banks[num];
+ u32 val;
+ unsigned long timeout;
+ void __iomem *addr;
+ int ret = 0;
+
+ bank->id = num;
+ bank->mt = mt;
+
+ mtk_thermal_get_bank(bank);
+
+ val = readl(mt->thermal_base + TEMP_MSRCTL1);
+ /* pause periodic temperature measurement for sensing points */
+ writel(val | TEMP_MSRCTL1_SENSING_POINTS_PAUSE,
+ mt->thermal_base + TEMP_MSRCTL1);
+
+ /* wait until temperature measurement bus idle */
+ timeout = jiffies + HZ;
+ addr = mt->thermal_base + TEMP_MSRCTL1;
+
+ ret = readl_poll_timeout(addr, val, (val & TEMP_MSRCTL1_BUS_STA) == 0x0,
+ 0, timeout);
+ if (ret < 0)
+ goto out;
+
+ /* disable periodic temperature meausrement on sensing points */
+ writel(0x0, mt->thermal_base + TEMP_MONCTL0);
+
+out:
+ mtk_thermal_put_bank(bank);
+
+ return ret;
+}
+
static u64 of_get_phys_base(struct device_node *np)
{
u64 size64;
@@ -868,7 +915,6 @@ static int mtk_thermal_probe(struct platform_device *pdev)
struct device_node *auxadc, *apmixedsys, *np = pdev->dev.of_node;
struct mtk_thermal *mt;
struct resource *res;
- u64 auxadc_phys_base, apmixed_phys_base;
struct thermal_zone_device *tzdev;

mt = devm_kzalloc(&pdev->dev, sizeof(*mt), GFP_KERNEL);
@@ -904,11 +950,11 @@ static int mtk_thermal_probe(struct platform_device *pdev)
return -ENODEV;
}

- auxadc_phys_base = of_get_phys_base(auxadc);
+ mt->auxadc_phys_base = of_get_phys_base(auxadc);

of_node_put(auxadc);

- if (auxadc_phys_base == OF_BAD_ADDR) {
+ if (mt->auxadc_phys_base == OF_BAD_ADDR) {
dev_err(&pdev->dev, "Can't get auxadc phys address\n");
return -EINVAL;
}
@@ -919,11 +965,12 @@ static int mtk_thermal_probe(struct platform_device *pdev)
return -ENODEV;
}

- apmixed_phys_base = of_get_phys_base(apmixedsys);
+ mt->apmixed_phys_base = of_get_phys_base(apmixedsys);
+ mt->apmixed_base = of_iomap(apmixedsys, 0);

of_node_put(apmixedsys);

- if (apmixed_phys_base == OF_BAD_ADDR) {
+ if (mt->apmixed_phys_base == OF_BAD_ADDR) {
dev_err(&pdev->dev, "Can't get auxadc phys address\n");
return -EINVAL;
}
@@ -935,19 +982,19 @@ static int mtk_thermal_probe(struct platform_device *pdev)
ret = clk_prepare_enable(mt->clk_auxadc);
if (ret) {
dev_err(&pdev->dev, "Can't enable auxadc clk: %d\n", ret);
- return ret;
+ goto err_disable_clk_auxadc;
}

ret = clk_prepare_enable(mt->clk_peri_therm);
if (ret) {
dev_err(&pdev->dev, "Can't enable peri clk: %d\n", ret);
- goto err_disable_clk_auxadc;
+ goto err_disable_clk_peri_therm;
}

for (ctrl_id = 0; ctrl_id < mt->conf->num_controller ; ctrl_id++)
for (i = 0; i < mt->conf->num_banks; i++)
- mtk_thermal_init_bank(mt, i, apmixed_phys_base,
- auxadc_phys_base, ctrl_id);
+ mtk_thermal_init_bank(mt, i, mt->apmixed_phys_base,
+ mt->auxadc_phys_base, ctrl_id);

platform_set_drvdata(pdev, mt);

@@ -978,11 +1025,80 @@ static int mtk_thermal_remove(struct platform_device *pdev)
return 0;
}

+static int __maybe_unused mtk_thermal_suspend(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct mtk_thermal *mt = platform_get_drvdata(pdev);
+ int i, ret;
+
+ for (i = 0; i < mt->conf->num_banks; i++) {
+ ret = mtk_thermal_disable_sensing(mt, i);
+ if (ret)
+ goto out;
+ }
+
+ /* disable buffer */
+ writel(readl(mt->apmixed_base + APMIXED_SYS_TS_CON1) |
+ APMIXED_SYS_TS_CON1_BUFFER_OFF,
+ mt->apmixed_base + APMIXED_SYS_TS_CON1);
+
+ clk_disable_unprepare(mt->clk_peri_therm);
+ clk_disable_unprepare(mt->clk_auxadc);
+
+ return 0;
+
+out:
+ dev_err(&pdev->dev, "Failed to wait until bus idle\n");
+
+ return ret;
+}
+
+static int __maybe_unused mtk_thermal_resume(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct mtk_thermal *mt = platform_get_drvdata(pdev);
+ int i, ret, ctrl_id;
+
+ ret = device_reset(&pdev->dev);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(mt->clk_auxadc);
+ if (ret) {
+ dev_err(&pdev->dev, "Can't enable auxadc clk: %d\n", ret);
+ goto err_disable_clk_auxadc;
+ }
+
+ ret = clk_prepare_enable(mt->clk_peri_therm);
+ if (ret) {
+ dev_err(&pdev->dev, "Can't enable peri clk: %d\n", ret);
+ goto err_disable_clk_peri_therm;
+ }
+
+ for (ctrl_id = 0; ctrl_id < mt->conf->num_controller ; ctrl_id++)
+ for (i = 0; i < mt->conf->num_banks; i++)
+ mtk_thermal_init_bank(mt, i, mt->apmixed_phys_base,
+ mt->auxadc_phys_base, ctrl_id);
+
+ return 0;
+
+err_disable_clk_peri_therm:
+ clk_disable_unprepare(mt->clk_peri_therm);
+err_disable_clk_auxadc:
+ clk_disable_unprepare(mt->clk_auxadc);
+
+ return ret;
+}
+
+static SIMPLE_DEV_PM_OPS(mtk_thermal_pm_ops,
+ mtk_thermal_suspend, mtk_thermal_resume);
+
static struct platform_driver mtk_thermal_driver = {
.probe = mtk_thermal_probe,
.remove = mtk_thermal_remove,
.driver = {
.name = "mtk-thermal",
+ .pm = &mtk_thermal_pm_ops,
.of_match_table = mtk_thermal_of_match,
},
};
--
2.18.0