ADM1177 is a Hot Swap Controller and Digital Power Monitor with
Soft Start Pin.
Datasheet:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1177.pdf
Signed-off-by: Beniamin Bia <[email protected]>
---
Documentation/hwmon/adm1177.rst | 36 ++++
drivers/hwmon/Kconfig | 10 ++
drivers/hwmon/Makefile | 1 +
drivers/hwmon/adm1177.c | 293 ++++++++++++++++++++++++++++++++
4 files changed, 340 insertions(+)
create mode 100644 Documentation/hwmon/adm1177.rst
create mode 100644 drivers/hwmon/adm1177.c
diff --git a/Documentation/hwmon/adm1177.rst b/Documentation/hwmon/adm1177.rst
new file mode 100644
index 000000000000..c81e0b4abd28
--- /dev/null
+++ b/Documentation/hwmon/adm1177.rst
@@ -0,0 +1,36 @@
+Kernel driver adm1177
+=====================
+
+Supported chips:
+ * Analog Devices ADM1177
+ Prefix: 'adm1177'
+ Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1177.pdf
+
+Author: Beniamin Bia <[email protected]>
+
+
+Description
+-----------
+
+This driver supports hardware monitoring for Analog Devices ADM1177
+Hot-Swap Controller and Digital Power Monitors with Soft Start Pin.
+
+
+Usage Notes
+-----------
+
+This driver does not auto-detect devices. You will have to instantiate the
+devices explicitly. Please see Documentation/i2c/instantiating-devices for
+details.
+
+
+Sysfs entries
+-------------
+
+The following attributes are supported. Current maxim attribute
+is read-write, all other attributes are read-only.
+
+in0_input Measured voltage in microvolts.
+
+curr1_input Measured current in microamperes.
+curr1_max_alarm Overcurrent alarm in microamperes.
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index 5308c59d7001..3db8f5752675 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -164,6 +164,16 @@ config SENSORS_ADM1031
This driver can also be built as a module. If so, the module
will be called adm1031.
+config SENSORS_ADM1177
+ tristate "Analog Devices ADM1177 and compatibles"
+ depends on I2C
+ help
+ If you say yes here you get support for Analog Devices ADM1177
+ sensor chips.
+
+ This driver can also be built as a module. If so, the module
+ will be called adm1177.
+
config SENSORS_ADM9240
tristate "Analog Devices ADM9240 and compatibles"
depends on I2C
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index 40c036ea45e6..27d04eab1be4 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -34,6 +34,7 @@ obj-$(CONFIG_SENSORS_ADM1025) += adm1025.o
obj-$(CONFIG_SENSORS_ADM1026) += adm1026.o
obj-$(CONFIG_SENSORS_ADM1029) += adm1029.o
obj-$(CONFIG_SENSORS_ADM1031) += adm1031.o
+obj-$(CONFIG_SENSORS_ADM1177) += adm1177.o
obj-$(CONFIG_SENSORS_ADM9240) += adm9240.o
obj-$(CONFIG_SENSORS_ADS7828) += ads7828.o
obj-$(CONFIG_SENSORS_ADS7871) += ads7871.o
diff --git a/drivers/hwmon/adm1177.c b/drivers/hwmon/adm1177.c
new file mode 100644
index 000000000000..aaa9e17289f4
--- /dev/null
+++ b/drivers/hwmon/adm1177.c
@@ -0,0 +1,293 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ADM1177 Hot Swap Controller and Digital Power Monitor with Soft Start Pin
+ *
+ * Copyright 2015-2019 Analog Devices Inc.
+ */
+
+#include <linux/bits.h>
+#include <linux/device.h>
+#include <linux/hwmon.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/regulator/consumer.h>
+
+/* Command Byte Operations */
+#define ADM1177_CMD_V_CONT BIT(0)
+#define ADM1177_CMD_I_CONT BIT(2)
+#define ADM1177_CMD_VRANGE BIT(4)
+
+/* Extended Register */
+#define ADM1177_REG_ALERT_TH 2
+
+#define ADM1177_BITS 12
+
+/**
+ * struct adm1177_state - driver instance specific data
+ * @client pointer to i2c client
+ * @reg regulator info for the the power supply of the device
+ * @r_sense_uohm current sense resistor value
+ * @alert_threshold_ua current limit for shutdown
+ * @vrange_high internal voltage divider
+ */
+struct adm1177_state {
+ struct i2c_client *client;
+ struct regulator *reg;
+ u32 r_sense_uohm;
+ u32 alert_threshold_ua;
+ bool vrange_high;
+};
+
+static int adm1177_read_raw(struct adm1177_state *st, u8 num, u8 *data)
+{
+ return i2c_master_recv(st->client, data, num);
+}
+
+static int adm1177_write_cmd(struct adm1177_state *st, u8 cmd)
+{
+ return i2c_smbus_write_byte(st->client, cmd);
+}
+
+static int adm1177_write_alert_thr(struct adm1177_state *st,
+ u32 alert_threshold_ua)
+{
+ u64 val;
+ int ret;
+
+ val = 0xFFULL * alert_threshold_ua * st->r_sense_uohm;
+ val = div_u64(val, 105840000U);
+ val = div_u64(val, 1000U);
+ if (val > 0xFF) {
+ dev_warn(&st->client->dev,
+ "Requested shutdown current %d uA above limit\n",
+ alert_threshold_ua);
+
+ return -EINVAL;
+ }
+
+ ret = i2c_smbus_write_byte_data(st->client, ADM1177_REG_ALERT_TH,
+ val);
+ if (!ret)
+ return ret;
+
+ st->alert_threshold_ua = alert_threshold_ua;
+ return 0;
+}
+
+static int adm1177_read(struct device *dev, enum hwmon_sensor_types type,
+ u32 attr, int channel, long *val)
+{
+ struct adm1177_state *st = dev_get_drvdata(dev);
+ u8 data[3];
+ long dummy;
+ int ret;
+
+ switch (type) {
+ case hwmon_curr:
+ switch (attr) {
+ case hwmon_curr_input:
+ ret = adm1177_read_raw(st, 3, data);
+ if (ret < 0)
+ return ret;
+ dummy = (data[1] << 4) | (data[2] & 0xF);
+ /*
+ * convert to milliamperes
+ * ((105.84mV / 4096) x raw) / senseResistor(ohm)
+ */
+ *val = div_u64((105840000ull * dummy),
+ 4096 * st->r_sense_uohm);
+ return 0;
+ case hwmon_curr_max_alarm:
+ *val = st->alert_threshold_ua;
+ return 0;
+ default:
+ return -EOPNOTSUPP;
+ }
+ case hwmon_in:
+ ret = adm1177_read_raw(st, 3, data);
+ if (ret < 0)
+ return ret;
+ dummy = (data[0] << 4) | (data[2] >> 4);
+ /*
+ * convert to millivolts based on resistor devision
+ * (V_fullscale / 4096) * raw
+ */
+ if (st->vrange_high)
+ dummy *= 26350;
+ else
+ dummy *= 6650;
+
+ *val = DIV_ROUND_CLOSEST(dummy, 4096);
+ return 0;
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+
+static int adm1177_write(struct device *dev, enum hwmon_sensor_types type,
+ u32 attr, int channel, long val)
+{
+ struct adm1177_state *st = dev_get_drvdata(dev);
+
+ switch (type) {
+ case hwmon_curr:
+ switch (attr) {
+ case hwmon_curr_max_alarm:
+ adm1177_write_alert_thr(st, val);
+ return 0;
+ default:
+ return -EOPNOTSUPP;
+ }
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+
+static umode_t adm1177_is_visible(const void *data,
+ enum hwmon_sensor_types type,
+ u32 attr, int channel)
+{
+ const struct adm1177_state *st = data;
+
+ switch (type) {
+ case hwmon_in:
+ switch (attr) {
+ case hwmon_in_input:
+ return 0444;
+ }
+ break;
+ case hwmon_curr:
+ switch (attr) {
+ case hwmon_curr_input:
+ if (st->r_sense_uohm)
+ return 0444;
+ return 0;
+ case hwmon_curr_max_alarm:
+ if (st->r_sense_uohm)
+ return 0644;
+ return 0;
+ }
+ break;
+ default:
+ break;
+ }
+ return 0;
+}
+
+static const struct hwmon_channel_info *adm1177_info[] = {
+ HWMON_CHANNEL_INFO(curr,
+ HWMON_C_INPUT | HWMON_C_MAX_ALARM),
+ HWMON_CHANNEL_INFO(in,
+ HWMON_I_INPUT),
+ NULL
+};
+
+static const struct hwmon_ops adm1177_hwmon_ops = {
+ .is_visible = adm1177_is_visible,
+ .read = adm1177_read,
+ .write = adm1177_write,
+};
+
+static const struct hwmon_chip_info adm1177_chip_info = {
+ .ops = &adm1177_hwmon_ops,
+ .info = adm1177_info,
+};
+
+static void adm1177_remove(void *data)
+{
+ struct adm1177_state *st = data;
+
+ regulator_disable(st->reg);
+}
+
+static int adm1177_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct device *dev = &client->dev;
+ struct device *hwmon_dev;
+ struct adm1177_state *st;
+ u32 alert_threshold_ua;
+ int ret;
+
+ st = devm_kzalloc(dev, sizeof(*st), GFP_KERNEL);
+ if (!st)
+ return -ENOMEM;
+
+ st->client = client;
+
+ st->reg = devm_regulator_get_optional(&client->dev, "vref");
+ if (IS_ERR(st->reg)) {
+ if (PTR_ERR(st->reg) == -EPROBE_DEFER)
+ return -EPROBE_DEFER;
+
+ st->reg = NULL;
+ } else {
+ ret = regulator_enable(st->reg);
+ if (ret)
+ return ret;
+ ret = devm_add_action_or_reset(&client->dev, adm1177_remove,
+ st);
+ if (ret)
+ return ret;
+ }
+
+ if (device_property_read_u32(dev, "shunt-resistor-micro-ohms",
+ &st->r_sense_uohm))
+ st->r_sense_uohm = 0;
+ if (device_property_read_u32(dev, "adi,shutdown-threshold-microamp",
+ &alert_threshold_ua)) {
+ if (st->r_sense_uohm)
+ /*
+ * set maximum default value from datasheet based on
+ * shunt-resistor
+ */
+ alert_threshold_ua = div_u64(105840000000,
+ st->r_sense_uohm);
+ else
+ alert_threshold_ua = 0;
+ }
+ st->vrange_high = device_property_read_bool(dev,
+ "adi,vrange-high-enable");
+ if (alert_threshold_ua && st->r_sense_uohm)
+ adm1177_write_alert_thr(st, alert_threshold_ua);
+
+ ret = adm1177_write_cmd(st, ADM1177_CMD_V_CONT |
+ ADM1177_CMD_I_CONT |
+ (st->vrange_high ? 0 : ADM1177_CMD_VRANGE));
+ if (ret)
+ return ret;
+
+ hwmon_dev =
+ devm_hwmon_device_register_with_info(dev, client->name, st,
+ &adm1177_chip_info, NULL);
+ return PTR_ERR_OR_ZERO(hwmon_dev);
+}
+
+static const struct i2c_device_id adm1177_id[] = {
+ {"adm1177", 0},
+ {}
+};
+MODULE_DEVICE_TABLE(i2c, adm1177_id);
+
+static const struct of_device_id adm1177_dt_ids[] = {
+ { .compatible = "adi,adm1177" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, adm1177_dt_ids);
+
+static struct i2c_driver adm1177_driver = {
+ .class = I2C_CLASS_HWMON,
+ .driver = {
+ .name = "adm1177",
+ .of_match_table = adm1177_dt_ids,
+ },
+ .probe = adm1177_probe,
+ .id_table = adm1177_id,
+};
+module_i2c_driver(adm1177_driver);
+
+MODULE_AUTHOR("Beniamin Bia <[email protected]>");
+MODULE_AUTHOR("Michael Hennerich <[email protected]>");
+MODULE_DESCRIPTION("Analog Devices ADM1177 ADC driver");
+MODULE_LICENSE("GPL v2");
--
2.17.1
Ignore this patch, the changes weren't specified.
On Thu, 2019-12-19 at 13:39 +0200, Beniamin Bia wrote:
> ADM1177 is a Hot Swap Controller and Digital Power Monitor with
> Soft Start Pin.
>
> Datasheet:
> Link:
> https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1177.pdf
>
> Signed-off-by: Beniamin Bia <[email protected]>
> ---
> Documentation/hwmon/adm1177.rst | 36 ++++
> drivers/hwmon/Kconfig | 10 ++
> drivers/hwmon/Makefile | 1 +
> drivers/hwmon/adm1177.c | 293
> ++++++++++++++++++++++++++++++++
> 4 files changed, 340 insertions(+)
> create mode 100644 Documentation/hwmon/adm1177.rst
> create mode 100644 drivers/hwmon/adm1177.c
>
> diff --git a/Documentation/hwmon/adm1177.rst
> b/Documentation/hwmon/adm1177.rst
> new file mode 100644
> index 000000000000..c81e0b4abd28
> --- /dev/null
> +++ b/Documentation/hwmon/adm1177.rst
> @@ -0,0 +1,36 @@
> +Kernel driver adm1177
> +=====================
> +
> +Supported chips:
> + * Analog Devices ADM1177
> + Prefix: 'adm1177'
> + Datasheet:
> https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1177.pdf
> +
> +Author: Beniamin Bia <[email protected]>
> +
> +
> +Description
> +-----------
> +
> +This driver supports hardware monitoring for Analog Devices ADM1177
> +Hot-Swap Controller and Digital Power Monitors with Soft Start Pin.
> +
> +
> +Usage Notes
> +-----------
> +
> +This driver does not auto-detect devices. You will have to
> instantiate the
> +devices explicitly. Please see Documentation/i2c/instantiating-
> devices for
> +details.
> +
> +
> +Sysfs entries
> +-------------
> +
> +The following attributes are supported. Current maxim attribute
> +is read-write, all other attributes are read-only.
> +
> +in0_input Measured voltage in microvolts.
> +
> +curr1_input Measured current in microamperes.
> +curr1_max_alarm Overcurrent alarm in microamperes.
> diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
> index 5308c59d7001..3db8f5752675 100644
> --- a/drivers/hwmon/Kconfig
> +++ b/drivers/hwmon/Kconfig
> @@ -164,6 +164,16 @@ config SENSORS_ADM1031
> This driver can also be built as a module. If so, the module
> will be called adm1031.
>
> +config SENSORS_ADM1177
> + tristate "Analog Devices ADM1177 and compatibles"
> + depends on I2C
> + help
> + If you say yes here you get support for Analog Devices
> ADM1177
> + sensor chips.
> +
> + This driver can also be built as a module. If so, the module
> + will be called adm1177.
> +
> config SENSORS_ADM9240
> tristate "Analog Devices ADM9240 and compatibles"
> depends on I2C
> diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
> index 40c036ea45e6..27d04eab1be4 100644
> --- a/drivers/hwmon/Makefile
> +++ b/drivers/hwmon/Makefile
> @@ -34,6 +34,7 @@ obj-$(CONFIG_SENSORS_ADM1025) += adm1025.o
> obj-$(CONFIG_SENSORS_ADM1026) += adm1026.o
> obj-$(CONFIG_SENSORS_ADM1029) += adm1029.o
> obj-$(CONFIG_SENSORS_ADM1031) += adm1031.o
> +obj-$(CONFIG_SENSORS_ADM1177) += adm1177.o
> obj-$(CONFIG_SENSORS_ADM9240) += adm9240.o
> obj-$(CONFIG_SENSORS_ADS7828) += ads7828.o
> obj-$(CONFIG_SENSORS_ADS7871) += ads7871.o
> diff --git a/drivers/hwmon/adm1177.c b/drivers/hwmon/adm1177.c
> new file mode 100644
> index 000000000000..aaa9e17289f4
> --- /dev/null
> +++ b/drivers/hwmon/adm1177.c
> @@ -0,0 +1,293 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * ADM1177 Hot Swap Controller and Digital Power Monitor with Soft
> Start Pin
> + *
> + * Copyright 2015-2019 Analog Devices Inc.
> + */
> +
> +#include <linux/bits.h>
> +#include <linux/device.h>
> +#include <linux/hwmon.h>
> +#include <linux/i2c.h>
> +#include <linux/init.h>
> +#include <linux/module.h>
> +#include <linux/regulator/consumer.h>
> +
> +/* Command Byte Operations */
> +#define ADM1177_CMD_V_CONT BIT(0)
> +#define ADM1177_CMD_I_CONT BIT(2)
> +#define ADM1177_CMD_VRANGE BIT(4)
> +
> +/* Extended Register */
> +#define ADM1177_REG_ALERT_TH 2
> +
> +#define ADM1177_BITS 12
> +
> +/**
> + * struct adm1177_state - driver instance specific data
> + * @client pointer to i2c client
> + * @reg regulator info for the the power supply
> of the device
> + * @r_sense_uohm current sense resistor value
> + * @alert_threshold_ua current limit for shutdown
> + * @vrange_high internal voltage divider
> + */
> +struct adm1177_state {
> + struct i2c_client *client;
> + struct regulator *reg;
> + u32 r_sense_uohm;
> + u32 alert_threshold_ua;
> + bool vrange_high;
> +};
> +
> +static int adm1177_read_raw(struct adm1177_state *st, u8 num, u8
> *data)
> +{
> + return i2c_master_recv(st->client, data, num);
> +}
> +
> +static int adm1177_write_cmd(struct adm1177_state *st, u8 cmd)
> +{
> + return i2c_smbus_write_byte(st->client, cmd);
> +}
> +
> +static int adm1177_write_alert_thr(struct adm1177_state *st,
> + u32 alert_threshold_ua)
> +{
> + u64 val;
> + int ret;
> +
> + val = 0xFFULL * alert_threshold_ua * st->r_sense_uohm;
> + val = div_u64(val, 105840000U);
> + val = div_u64(val, 1000U);
> + if (val > 0xFF) {
> + dev_warn(&st->client->dev,
> + "Requested shutdown current %d uA above
> limit\n",
> + alert_threshold_ua);
> +
> + return -EINVAL;
> + }
> +
> + ret = i2c_smbus_write_byte_data(st->client,
> ADM1177_REG_ALERT_TH,
> + val);
> + if (!ret)
> + return ret;
> +
> + st->alert_threshold_ua = alert_threshold_ua;
> + return 0;
> +}
> +
> +static int adm1177_read(struct device *dev, enum hwmon_sensor_types
> type,
> + u32 attr, int channel, long *val)
> +{
> + struct adm1177_state *st = dev_get_drvdata(dev);
> + u8 data[3];
> + long dummy;
> + int ret;
> +
> + switch (type) {
> + case hwmon_curr:
> + switch (attr) {
> + case hwmon_curr_input:
> + ret = adm1177_read_raw(st, 3, data);
> + if (ret < 0)
> + return ret;
> + dummy = (data[1] << 4) | (data[2] & 0xF);
> + /*
> + * convert to milliamperes
> + * ((105.84mV / 4096) x raw) /
> senseResistor(ohm)
> + */
> + *val = div_u64((105840000ull * dummy),
> + 4096 * st->r_sense_uohm);
> + return 0;
> + case hwmon_curr_max_alarm:
> + *val = st->alert_threshold_ua;
> + return 0;
> + default:
> + return -EOPNOTSUPP;
> + }
> + case hwmon_in:
> + ret = adm1177_read_raw(st, 3, data);
> + if (ret < 0)
> + return ret;
> + dummy = (data[0] << 4) | (data[2] >> 4);
> + /*
> + * convert to millivolts based on resistor devision
> + * (V_fullscale / 4096) * raw
> + */
> + if (st->vrange_high)
> + dummy *= 26350;
> + else
> + dummy *= 6650;
> +
> + *val = DIV_ROUND_CLOSEST(dummy, 4096);
> + return 0;
> + default:
> + return -EOPNOTSUPP;
> + }
> +}
> +
> +static int adm1177_write(struct device *dev, enum hwmon_sensor_types
> type,
> + u32 attr, int channel, long val)
> +{
> + struct adm1177_state *st = dev_get_drvdata(dev);
> +
> + switch (type) {
> + case hwmon_curr:
> + switch (attr) {
> + case hwmon_curr_max_alarm:
> + adm1177_write_alert_thr(st, val);
> + return 0;
> + default:
> + return -EOPNOTSUPP;
> + }
> + default:
> + return -EOPNOTSUPP;
> + }
> +}
> +
> +static umode_t adm1177_is_visible(const void *data,
> + enum hwmon_sensor_types type,
> + u32 attr, int channel)
> +{
> + const struct adm1177_state *st = data;
> +
> + switch (type) {
> + case hwmon_in:
> + switch (attr) {
> + case hwmon_in_input:
> + return 0444;
> + }
> + break;
> + case hwmon_curr:
> + switch (attr) {
> + case hwmon_curr_input:
> + if (st->r_sense_uohm)
> + return 0444;
> + return 0;
> + case hwmon_curr_max_alarm:
> + if (st->r_sense_uohm)
> + return 0644;
> + return 0;
> + }
> + break;
> + default:
> + break;
> + }
> + return 0;
> +}
> +
> +static const struct hwmon_channel_info *adm1177_info[] = {
> + HWMON_CHANNEL_INFO(curr,
> + HWMON_C_INPUT | HWMON_C_MAX_ALARM),
> + HWMON_CHANNEL_INFO(in,
> + HWMON_I_INPUT),
> + NULL
> +};
> +
> +static const struct hwmon_ops adm1177_hwmon_ops = {
> + .is_visible = adm1177_is_visible,
> + .read = adm1177_read,
> + .write = adm1177_write,
> +};
> +
> +static const struct hwmon_chip_info adm1177_chip_info = {
> + .ops = &adm1177_hwmon_ops,
> + .info = adm1177_info,
> +};
> +
> +static void adm1177_remove(void *data)
> +{
> + struct adm1177_state *st = data;
> +
> + regulator_disable(st->reg);
> +}
> +
> +static int adm1177_probe(struct i2c_client *client,
> + const struct i2c_device_id *id)
> +{
> + struct device *dev = &client->dev;
> + struct device *hwmon_dev;
> + struct adm1177_state *st;
> + u32 alert_threshold_ua;
> + int ret;
> +
> + st = devm_kzalloc(dev, sizeof(*st), GFP_KERNEL);
> + if (!st)
> + return -ENOMEM;
> +
> + st->client = client;
> +
> + st->reg = devm_regulator_get_optional(&client->dev, "vref");
> + if (IS_ERR(st->reg)) {
> + if (PTR_ERR(st->reg) == -EPROBE_DEFER)
> + return -EPROBE_DEFER;
> +
> + st->reg = NULL;
> + } else {
> + ret = regulator_enable(st->reg);
> + if (ret)
> + return ret;
> + ret = devm_add_action_or_reset(&client->dev,
> adm1177_remove,
> + st);
> + if (ret)
> + return ret;
> + }
> +
> + if (device_property_read_u32(dev, "shunt-resistor-micro-ohms",
> + &st->r_sense_uohm))
> + st->r_sense_uohm = 0;
> + if (device_property_read_u32(dev, "adi,shutdown-threshold-
> microamp",
> + &alert_threshold_ua)) {
> + if (st->r_sense_uohm)
> + /*
> + * set maximum default value from datasheet
> based on
> + * shunt-resistor
> + */
> + alert_threshold_ua = div_u64(105840000000,
> + st->r_sense_uohm);
> + else
> + alert_threshold_ua = 0;
> + }
> + st->vrange_high = device_property_read_bool(dev,
> + "adi,vrange-high-
> enable");
> + if (alert_threshold_ua && st->r_sense_uohm)
> + adm1177_write_alert_thr(st, alert_threshold_ua);
> +
> + ret = adm1177_write_cmd(st, ADM1177_CMD_V_CONT |
> + ADM1177_CMD_I_CONT |
> + (st->vrange_high ? 0 :
> ADM1177_CMD_VRANGE));
> + if (ret)
> + return ret;
> +
> + hwmon_dev =
> + devm_hwmon_device_register_with_info(dev, client->name,
> st,
> + &adm1177_chip_info
> , NULL);
> + return PTR_ERR_OR_ZERO(hwmon_dev);
> +}
> +
> +static const struct i2c_device_id adm1177_id[] = {
> + {"adm1177", 0},
> + {}
> +};
> +MODULE_DEVICE_TABLE(i2c, adm1177_id);
> +
> +static const struct of_device_id adm1177_dt_ids[] = {
> + { .compatible = "adi,adm1177" },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, adm1177_dt_ids);
> +
> +static struct i2c_driver adm1177_driver = {
> + .class = I2C_CLASS_HWMON,
> + .driver = {
> + .name = "adm1177",
> + .of_match_table = adm1177_dt_ids,
> + },
> + .probe = adm1177_probe,
> + .id_table = adm1177_id,
> +};
> +module_i2c_driver(adm1177_driver);
> +
> +MODULE_AUTHOR("Beniamin Bia <[email protected]>");
> +MODULE_AUTHOR("Michael Hennerich <[email protected]>");
> +MODULE_DESCRIPTION("Analog Devices ADM1177 ADC driver");
> +MODULE_LICENSE("GPL v2");
On Thu, Dec 19, 2019 at 01:39:24PM +0200, Beniamin Bia wrote:
> ADM1177 is a Hot Swap Controller and Digital Power Monitor with
> Soft Start Pin.
>
> Datasheet:
> Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1177.pdf
>
> Signed-off-by: Beniamin Bia <[email protected]>
> ---
> Documentation/hwmon/adm1177.rst | 36 ++++
> drivers/hwmon/Kconfig | 10 ++
> drivers/hwmon/Makefile | 1 +
> drivers/hwmon/adm1177.c | 293 ++++++++++++++++++++++++++++++++
> 4 files changed, 340 insertions(+)
> create mode 100644 Documentation/hwmon/adm1177.rst
> create mode 100644 drivers/hwmon/adm1177.c
>
> diff --git a/Documentation/hwmon/adm1177.rst b/Documentation/hwmon/adm1177.rst
> new file mode 100644
> index 000000000000..c81e0b4abd28
> --- /dev/null
> +++ b/Documentation/hwmon/adm1177.rst
> @@ -0,0 +1,36 @@
> +Kernel driver adm1177
> +=====================
> +
> +Supported chips:
> + * Analog Devices ADM1177
> + Prefix: 'adm1177'
> + Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1177.pdf
> +
> +Author: Beniamin Bia <[email protected]>
> +
> +
> +Description
> +-----------
> +
> +This driver supports hardware monitoring for Analog Devices ADM1177
> +Hot-Swap Controller and Digital Power Monitors with Soft Start Pin.
> +
> +
> +Usage Notes
> +-----------
> +
> +This driver does not auto-detect devices. You will have to instantiate the
> +devices explicitly. Please see Documentation/i2c/instantiating-devices for
> +details.
> +
> +
> +Sysfs entries
> +-------------
> +
> +The following attributes are supported. Current maxim attribute
> +is read-write, all other attributes are read-only.
> +
> +in0_input Measured voltage in microvolts.
> +
> +curr1_input Measured current in microamperes.
> +curr1_max_alarm Overcurrent alarm in microamperes.
> diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
> index 5308c59d7001..3db8f5752675 100644
> --- a/drivers/hwmon/Kconfig
> +++ b/drivers/hwmon/Kconfig
> @@ -164,6 +164,16 @@ config SENSORS_ADM1031
> This driver can also be built as a module. If so, the module
> will be called adm1031.
>
> +config SENSORS_ADM1177
> + tristate "Analog Devices ADM1177 and compatibles"
> + depends on I2C
> + help
> + If you say yes here you get support for Analog Devices ADM1177
> + sensor chips.
> +
> + This driver can also be built as a module. If so, the module
> + will be called adm1177.
> +
> config SENSORS_ADM9240
> tristate "Analog Devices ADM9240 and compatibles"
> depends on I2C
> diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
> index 40c036ea45e6..27d04eab1be4 100644
> --- a/drivers/hwmon/Makefile
> +++ b/drivers/hwmon/Makefile
> @@ -34,6 +34,7 @@ obj-$(CONFIG_SENSORS_ADM1025) += adm1025.o
> obj-$(CONFIG_SENSORS_ADM1026) += adm1026.o
> obj-$(CONFIG_SENSORS_ADM1029) += adm1029.o
> obj-$(CONFIG_SENSORS_ADM1031) += adm1031.o
> +obj-$(CONFIG_SENSORS_ADM1177) += adm1177.o
> obj-$(CONFIG_SENSORS_ADM9240) += adm9240.o
> obj-$(CONFIG_SENSORS_ADS7828) += ads7828.o
> obj-$(CONFIG_SENSORS_ADS7871) += ads7871.o
> diff --git a/drivers/hwmon/adm1177.c b/drivers/hwmon/adm1177.c
> new file mode 100644
> index 000000000000..aaa9e17289f4
> --- /dev/null
> +++ b/drivers/hwmon/adm1177.c
> @@ -0,0 +1,293 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * ADM1177 Hot Swap Controller and Digital Power Monitor with Soft Start Pin
> + *
> + * Copyright 2015-2019 Analog Devices Inc.
> + */
> +
> +#include <linux/bits.h>
> +#include <linux/device.h>
> +#include <linux/hwmon.h>
> +#include <linux/i2c.h>
> +#include <linux/init.h>
> +#include <linux/module.h>
> +#include <linux/regulator/consumer.h>
> +
> +/* Command Byte Operations */
> +#define ADM1177_CMD_V_CONT BIT(0)
> +#define ADM1177_CMD_I_CONT BIT(2)
> +#define ADM1177_CMD_VRANGE BIT(4)
> +
> +/* Extended Register */
> +#define ADM1177_REG_ALERT_TH 2
> +
> +#define ADM1177_BITS 12
> +
> +/**
> + * struct adm1177_state - driver instance specific data
> + * @client pointer to i2c client
> + * @reg regulator info for the the power supply of the device
> + * @r_sense_uohm current sense resistor value
> + * @alert_threshold_ua current limit for shutdown
> + * @vrange_high internal voltage divider
> + */
> +struct adm1177_state {
> + struct i2c_client *client;
> + struct regulator *reg;
> + u32 r_sense_uohm;
> + u32 alert_threshold_ua;
> + bool vrange_high;
> +};
> +
> +static int adm1177_read_raw(struct adm1177_state *st, u8 num, u8 *data)
> +{
> + return i2c_master_recv(st->client, data, num);
> +}
> +
> +static int adm1177_write_cmd(struct adm1177_state *st, u8 cmd)
> +{
> + return i2c_smbus_write_byte(st->client, cmd);
> +}
> +
> +static int adm1177_write_alert_thr(struct adm1177_state *st,
> + u32 alert_threshold_ua)
> +{
> + u64 val;
> + int ret;
> +
> + val = 0xFFULL * alert_threshold_ua * st->r_sense_uohm;
> + val = div_u64(val, 105840000U);
> + val = div_u64(val, 1000U);
> + if (val > 0xFF) {
> + dev_warn(&st->client->dev,
> + "Requested shutdown current %d uA above limit\n",
> + alert_threshold_ua);
> +
> + return -EINVAL;
We don't expect the user to know the limits, and it isn't really a
good idea to expect the user to have to play with values to find it.
On top of that, clogging the kernel log with error messages like this
doesn't really add value.
Please clamp the value to the maximum instead, and adjust
alert_threshold_ua accordingly.
> + }
> +
> + ret = i2c_smbus_write_byte_data(st->client, ADM1177_REG_ALERT_TH,
> + val);
> + if (!ret)
> + return ret;
> +
> + st->alert_threshold_ua = alert_threshold_ua;
> + return 0;
> +}
> +
> +static int adm1177_read(struct device *dev, enum hwmon_sensor_types type,
> + u32 attr, int channel, long *val)
> +{
> + struct adm1177_state *st = dev_get_drvdata(dev);
> + u8 data[3];
> + long dummy;
> + int ret;
> +
> + switch (type) {
> + case hwmon_curr:
> + switch (attr) {
> + case hwmon_curr_input:
> + ret = adm1177_read_raw(st, 3, data);
> + if (ret < 0)
> + return ret;
> + dummy = (data[1] << 4) | (data[2] & 0xF);
> + /*
> + * convert to milliamperes
> + * ((105.84mV / 4096) x raw) / senseResistor(ohm)
> + */
> + *val = div_u64((105840000ull * dummy),
> + 4096 * st->r_sense_uohm);
> + return 0;
> + case hwmon_curr_max_alarm:
> + *val = st->alert_threshold_ua;
> + return 0;
> + default:
> + return -EOPNOTSUPP;
> + }
> + case hwmon_in:
> + ret = adm1177_read_raw(st, 3, data);
> + if (ret < 0)
> + return ret;
> + dummy = (data[0] << 4) | (data[2] >> 4);
> + /*
> + * convert to millivolts based on resistor devision
> + * (V_fullscale / 4096) * raw
> + */
> + if (st->vrange_high)
> + dummy *= 26350;
> + else
> + dummy *= 6650;
> +
> + *val = DIV_ROUND_CLOSEST(dummy, 4096);
> + return 0;
> + default:
> + return -EOPNOTSUPP;
> + }
> +}
> +
> +static int adm1177_write(struct device *dev, enum hwmon_sensor_types type,
> + u32 attr, int channel, long val)
> +{
> + struct adm1177_state *st = dev_get_drvdata(dev);
> +
> + switch (type) {
> + case hwmon_curr:
> + switch (attr) {
> + case hwmon_curr_max_alarm:
> + adm1177_write_alert_thr(st, val);
> + return 0;
> + default:
> + return -EOPNOTSUPP;
> + }
> + default:
> + return -EOPNOTSUPP;
> + }
> +}
> +
> +static umode_t adm1177_is_visible(const void *data,
> + enum hwmon_sensor_types type,
> + u32 attr, int channel)
> +{
> + const struct adm1177_state *st = data;
> +
> + switch (type) {
> + case hwmon_in:
> + switch (attr) {
> + case hwmon_in_input:
> + return 0444;
> + }
> + break;
> + case hwmon_curr:
> + switch (attr) {
> + case hwmon_curr_input:
> + if (st->r_sense_uohm)
> + return 0444;
> + return 0;
> + case hwmon_curr_max_alarm:
> + if (st->r_sense_uohm)
> + return 0644;
> + return 0;
> + }
> + break;
> + default:
> + break;
> + }
> + return 0;
> +}
> +
> +static const struct hwmon_channel_info *adm1177_info[] = {
> + HWMON_CHANNEL_INFO(curr,
> + HWMON_C_INPUT | HWMON_C_MAX_ALARM),
> + HWMON_CHANNEL_INFO(in,
> + HWMON_I_INPUT),
> + NULL
> +};
> +
> +static const struct hwmon_ops adm1177_hwmon_ops = {
> + .is_visible = adm1177_is_visible,
> + .read = adm1177_read,
> + .write = adm1177_write,
> +};
> +
> +static const struct hwmon_chip_info adm1177_chip_info = {
> + .ops = &adm1177_hwmon_ops,
> + .info = adm1177_info,
> +};
> +
> +static void adm1177_remove(void *data)
> +{
> + struct adm1177_state *st = data;
> +
> + regulator_disable(st->reg);
> +}
> +
> +static int adm1177_probe(struct i2c_client *client,
> + const struct i2c_device_id *id)
> +{
> + struct device *dev = &client->dev;
> + struct device *hwmon_dev;
> + struct adm1177_state *st;
> + u32 alert_threshold_ua;
> + int ret;
> +
> + st = devm_kzalloc(dev, sizeof(*st), GFP_KERNEL);
> + if (!st)
> + return -ENOMEM;
> +
> + st->client = client;
> +
> + st->reg = devm_regulator_get_optional(&client->dev, "vref");
> + if (IS_ERR(st->reg)) {
> + if (PTR_ERR(st->reg) == -EPROBE_DEFER)
> + return -EPROBE_DEFER;
> +
> + st->reg = NULL;
> + } else {
> + ret = regulator_enable(st->reg);
> + if (ret)
> + return ret;
> + ret = devm_add_action_or_reset(&client->dev, adm1177_remove,
> + st);
> + if (ret)
> + return ret;
> + }
> +
> + if (device_property_read_u32(dev, "shunt-resistor-micro-ohms",
> + &st->r_sense_uohm))
> + st->r_sense_uohm = 0;
> + if (device_property_read_u32(dev, "adi,shutdown-threshold-microamp",
> + &alert_threshold_ua)) {
> + if (st->r_sense_uohm)
> + /*
> + * set maximum default value from datasheet based on
> + * shunt-resistor
> + */
> + alert_threshold_ua = div_u64(105840000000,
> + st->r_sense_uohm);
> + else
> + alert_threshold_ua = 0;
> + }
> + st->vrange_high = device_property_read_bool(dev,
> + "adi,vrange-high-enable");
> + if (alert_threshold_ua && st->r_sense_uohm)
> + adm1177_write_alert_thr(st, alert_threshold_ua);
> +
> + ret = adm1177_write_cmd(st, ADM1177_CMD_V_CONT |
> + ADM1177_CMD_I_CONT |
> + (st->vrange_high ? 0 : ADM1177_CMD_VRANGE));
> + if (ret)
> + return ret;
> +
> + hwmon_dev =
> + devm_hwmon_device_register_with_info(dev, client->name, st,
> + &adm1177_chip_info, NULL);
> + return PTR_ERR_OR_ZERO(hwmon_dev);
> +}
> +
> +static const struct i2c_device_id adm1177_id[] = {
> + {"adm1177", 0},
> + {}
> +};
> +MODULE_DEVICE_TABLE(i2c, adm1177_id);
> +
> +static const struct of_device_id adm1177_dt_ids[] = {
> + { .compatible = "adi,adm1177" },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, adm1177_dt_ids);
> +
> +static struct i2c_driver adm1177_driver = {
> + .class = I2C_CLASS_HWMON,
> + .driver = {
> + .name = "adm1177",
> + .of_match_table = adm1177_dt_ids,
> + },
> + .probe = adm1177_probe,
> + .id_table = adm1177_id,
> +};
> +module_i2c_driver(adm1177_driver);
> +
> +MODULE_AUTHOR("Beniamin Bia <[email protected]>");
> +MODULE_AUTHOR("Michael Hennerich <[email protected]>");
> +MODULE_DESCRIPTION("Analog Devices ADM1177 ADC driver");
> +MODULE_LICENSE("GPL v2");