This patch series add support for PMIC regulator driver for Monolithic
Power System's MP5416 chipset. MP5416 provides support for 4-BUCK converter,
4-LDO regualtor, accessed over I2C.
Thanks,
Saravanan
Saravanan Sekar (3):
dt-bindings: regulator: add document bindings for mp5416
regulator: mp5416: add mp5416 regulator driver
MAINTAINERS: Add entry for mp5416 PMIC driver
.../bindings/regulator/mps,mp5416.yaml | 64 +++++
MAINTAINERS | 2 +
drivers/regulator/Kconfig | 10 +
drivers/regulator/Makefile | 1 +
drivers/regulator/mp5416.c | 245 ++++++++++++++++++
5 files changed, 322 insertions(+)
create mode 100644 Documentation/devicetree/bindings/regulator/mps,mp5416.yaml
create mode 100644 drivers/regulator/mp5416.c
--
2.17.1
Add device tree binding information for mp5416 regulator driver.
Signed-off-by: Saravanan Sekar <[email protected]>
---
.../bindings/regulator/mps,mp5416.yaml | 78 +++++++++++++++++++
1 file changed, 78 insertions(+)
create mode 100644 Documentation/devicetree/bindings/regulator/mps,mp5416.yaml
diff --git a/Documentation/devicetree/bindings/regulator/mps,mp5416.yaml b/Documentation/devicetree/bindings/regulator/mps,mp5416.yaml
new file mode 100644
index 000000000000..702508e4267f
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/mps,mp5416.yaml
@@ -0,0 +1,78 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/mps,mp5416.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Monolithic Power System MP5416 PMIC
+
+maintainers:
+ - Saravanan Sekar <[email protected]>
+
+properties:
+ $nodename:
+ pattern: "pmic@[0-9a-f]{1,2}"
+ compatible:
+ enum:
+ - mps,mp5416
+
+ reg:
+ maxItems: 1
+
+ regulators:
+ type: object
+ allOf:
+ - $ref: regulator.yaml#
+ description: |
+ list of regulators provided by this controller, must be named
+ after their hardware counterparts BUCK[1-4] and LDO[1-4]
+
+ patternProperties:
+ "^buck[1-4]$":
+ $ref: "regulator.yaml#"
+ type: object
+
+ "^ldo[1-4]$":
+ $ref: "regulator.yaml#"
+ type: object
+
+ additionalProperties: false
+ additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - regulators
+
+additionalProperties: false
+
+examples:
+ - |
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmic@69 {
+ compatible = "mps,mp5416";
+ reg = <0x69>;
+
+ regulators {
+
+ buck1 {
+ regulator-name = "buck1";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <2187500>;
+ regulator-min-microamp = <3800000>;
+ regulator-max-microamp = <6800000>;
+ regulator-boot-on;
+ };
+
+ ldo2 {
+ regulator-name = "ldo2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3975000>;
+ };
+ };
+ };
+ };
+...
--
2.17.1
Adding regulator driver for the device mp5416.
The MP5416 PMIC device contains four DC-DC buck converters and
five regulators, accessed over I2C.
Signed-off-by: Saravanan Sekar <[email protected]>
---
drivers/regulator/Kconfig | 10 ++
drivers/regulator/Makefile | 1 +
drivers/regulator/mp5416.c | 245 +++++++++++++++++++++++++++++++++++++
3 files changed, 256 insertions(+)
create mode 100644 drivers/regulator/mp5416.c
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 97bfdd47954f..9925fd152cd6 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -612,6 +612,16 @@ config REGULATOR_MCP16502
through the regulator interface. In addition it enables
suspend-to-ram/standby transition.
+config REGULATOR_MP5416
+ tristate "Monolithic MP5416 PMIC"
+ depends on I2C && OF
+ select REGMAP_I2C
+ help
+ Say y here to support the MP5416 PMIC. This will enable supports
+ the software controllable 4 buck and 4 LDO regulators.
+ Say M here if you want to include support for the regulator as a
+ module.
+
config REGULATOR_MP8859
tristate "MPS MP8859 regulator driver"
depends on I2C
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 07bc977c52b0..ab7149734c03 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -78,6 +78,7 @@ obj-$(CONFIG_REGULATOR_MC13783) += mc13783-regulator.o
obj-$(CONFIG_REGULATOR_MC13892) += mc13892-regulator.o
obj-$(CONFIG_REGULATOR_MC13XXX_CORE) += mc13xxx-regulator-core.o
obj-$(CONFIG_REGULATOR_MCP16502) += mcp16502.o
+obj-$(CONFIG_REGULATOR_MP5416) += mp5416.o
obj-$(CONFIG_REGULATOR_MP8859) += mp8859.o
obj-$(CONFIG_REGULATOR_MPQ7920) += mpq7920.o
obj-$(CONFIG_REGULATOR_MT6311) += mt6311-regulator.o
diff --git a/drivers/regulator/mp5416.c b/drivers/regulator/mp5416.c
new file mode 100644
index 000000000000..7954ad17249b
--- /dev/null
+++ b/drivers/regulator/mp5416.c
@@ -0,0 +1,245 @@
+// SPDX-License-Identifier: GPL-2.0+
+//
+// mp5416.c - regulator driver for mps mp5416
+//
+// Copyright 2020 Monolithic Power Systems, Inc
+//
+// Author: Saravanan Sekar <[email protected]>
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/i2c.h>
+
+#define MP5416_REG_CTL0 0x00
+#define MP5416_REG_CTL1 0x01
+#define MP5416_REG_CTL2 0x02
+#define MP5416_REG_ILIM 0x03
+#define MP5416_REG_BUCK1 0x04
+#define MP5416_REG_BUCK2 0x05
+#define MP5416_REG_BUCK3 0x06
+#define MP5416_REG_BUCK4 0x07
+#define MP5416_REG_LDO1 0x08
+#define MP5416_REG_LDO2 0x09
+#define MP5416_REG_LDO3 0x0a
+#define MP5416_REG_LDO4 0x0b
+
+#define MP5416_REGULATOR_EN BIT(7)
+#define MP5416_MASK_VSET 0x7f
+#define MP5416_MASK_BUCK1_ILIM 0xc0
+#define MP5416_MASK_BUCK2_ILIM 0x0c
+#define MP5416_MASK_BUCK3_ILIM 0x30
+#define MP5416_MASK_BUCK4_ILIM 0x03
+#define MP5416_MASK_DVS_SLEWRATE 0xc0
+
+/* values in uV */
+#define MP5416_VOLT1_MIN 600000
+#define MP5416_VOLT1_MAX 2187500
+#define MP5416_VOLT1_STEP 12500
+#define MP5416_VOLT2_MIN 800000
+#define MP5416_VOLT2_MAX 3975000
+#define MP5416_VOLT2_STEP 25000
+
+#define MP5416_VOLT1_RANGE \
+ ((MP5416_VOLT1_MAX - MP5416_VOLT1_MIN)/MP5416_VOLT1_STEP + 1)
+#define MP5416_VOLT2_RANGE \
+ ((MP5416_VOLT2_MAX - MP5416_VOLT2_MIN)/MP5416_VOLT2_STEP + 1)
+
+#define MP5416BUCK(_name, _id, _ilim, _dreg, _dval, _vsel) \
+ [MP5416_BUCK ## _id] = { \
+ .id = MP5416_BUCK ## _id, \
+ .name = _name, \
+ .of_match = _name, \
+ .regulators_node = "regulators", \
+ .ops = &mp5416_buck_ops, \
+ .min_uV = MP5416_VOLT ##_vsel## _MIN, \
+ .uV_step = MP5416_VOLT ##_vsel## _STEP, \
+ .n_voltages = MP5416_VOLT ##_vsel## _RANGE, \
+ .curr_table = _ilim, \
+ .n_current_limits = ARRAY_SIZE(_ilim), \
+ .csel_reg = MP5416_REG_ILIM, \
+ .csel_mask = MP5416_MASK_BUCK ## _id ##_ILIM, \
+ .vsel_reg = MP5416_REG_BUCK ## _id, \
+ .vsel_mask = MP5416_MASK_VSET, \
+ .enable_reg = MP5416_REG_BUCK ## _id, \
+ .enable_mask = MP5416_REGULATOR_EN, \
+ .active_discharge_on = _dval, \
+ .active_discharge_reg = _dreg, \
+ .active_discharge_mask = _dval, \
+ .owner = THIS_MODULE, \
+ }
+
+#define MP5416LDO(_name, _id) \
+ [MP5416_LDO ## _id] = { \
+ .id = MP5416_LDO ## _id, \
+ .name = _name, \
+ .of_match = _name, \
+ .regulators_node = "regulators", \
+ .ops = &mp5416_ldo_ops, \
+ .min_uV = MP5416_VOLT2_MIN, \
+ .uV_step = MP5416_VOLT2_STEP, \
+ .n_voltages = MP5416_VOLT2_RANGE, \
+ .vsel_reg = MP5416_REG_LDO ##_id, \
+ .vsel_mask = MP5416_MASK_VSET, \
+ .enable_reg = MP5416_REG_LDO ##_id, \
+ .enable_mask = MP5416_REGULATOR_EN, \
+ .active_discharge_on = BIT(_id), \
+ .active_discharge_reg = MP5416_REG_CTL2, \
+ .active_discharge_mask = BIT(_id), \
+ .owner = THIS_MODULE, \
+ }
+
+enum mp5416_regulators {
+ MP5416_BUCK1,
+ MP5416_BUCK2,
+ MP5416_BUCK3,
+ MP5416_BUCK4,
+ MP5416_LDO1,
+ MP5416_LDO2,
+ MP5416_LDO3,
+ MP5416_LDO4,
+ MP5416_MAX_REGULATORS,
+};
+
+static const struct regmap_config mp5416_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = 0x0d,
+};
+
+/* Current limits array (in uA)
+ * ILIM1 & ILIM3
+ */
+static const unsigned int mp5416_I_limits1[] = {
+ 3800000, 4600000, 5600000, 6800000
+};
+
+/* ILIM2 & ILIM4 */
+static const unsigned int mp5416_I_limits2[] = {
+ 2200000, 3200000, 4200000, 5200000
+};
+
+static int mp5416_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay);
+
+static const struct regulator_ops mp5416_ldo_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_linear,
+ .map_voltage = regulator_map_voltage_linear,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .set_active_discharge = regulator_set_active_discharge_regmap,
+};
+
+static const struct regulator_ops mp5416_buck_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_linear,
+ .map_voltage = regulator_map_voltage_linear,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .set_active_discharge = regulator_set_active_discharge_regmap,
+ .get_current_limit = regulator_get_current_limit_regmap,
+ .set_current_limit = regulator_set_current_limit_regmap,
+ .set_ramp_delay = mp5416_set_ramp_delay,
+};
+
+static struct regulator_desc mp5416_regulators_desc[MP5416_MAX_REGULATORS] = {
+ MP5416BUCK("buck1", 1, mp5416_I_limits1, MP5416_REG_CTL1, BIT(0), 1),
+ MP5416BUCK("buck2", 2, mp5416_I_limits2, MP5416_REG_CTL1, BIT(1), 2),
+ MP5416BUCK("buck3", 3, mp5416_I_limits1, MP5416_REG_CTL1, BIT(2), 1),
+ MP5416BUCK("buck4", 4, mp5416_I_limits2, MP5416_REG_CTL2, BIT(5), 2),
+ MP5416LDO("ldo1", 1),
+ MP5416LDO("ldo2", 2),
+ MP5416LDO("ldo3", 3),
+ MP5416LDO("ldo4", 4),
+};
+
+/*
+ * DVS ramp rate BUCK1 to BUCK4
+ * 00: 32mV/us
+ * 01: 16mV/us
+ * 10: 8mV/us
+ * 11: 4mV/us
+ */
+static int mp5416_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay)
+{
+ unsigned int ramp_val;
+
+ if (ramp_delay > 32000 || ramp_delay < 0)
+ return -EINVAL;
+
+ if (ramp_delay <= 4000)
+ ramp_val = 3;
+ else if (ramp_delay <= 8000)
+ ramp_val = 2;
+ else if (ramp_delay <= 16000)
+ ramp_val = 1;
+ else
+ ramp_val = 0;
+
+ return regmap_update_bits(rdev->regmap, MP5416_REG_CTL2,
+ MP5416_MASK_DVS_SLEWRATE, ramp_val << 6);
+}
+
+static int mp5416_i2c_probe(struct i2c_client *client)
+{
+ struct device *dev = &client->dev;
+ struct regulator_config config = { NULL, };
+ struct regulator_dev *rdev;
+ struct regmap *regmap;
+ int i;
+
+ regmap = devm_regmap_init_i2c(client, &mp5416_regmap_config);
+ if (IS_ERR(regmap)) {
+ dev_err(dev, "Failed to allocate regmap!\n");
+ return PTR_ERR(regmap);
+ }
+
+ config.dev = dev;
+ config.regmap = regmap;
+
+ for (i = 0; i < MP5416_MAX_REGULATORS; i++) {
+ rdev = devm_regulator_register(dev,
+ &mp5416_regulators_desc[i],
+ &config);
+ if (IS_ERR(rdev)) {
+ dev_err(dev, "Failed to register regulator!\n");
+ return PTR_ERR(rdev);
+ }
+ }
+
+ return 0;
+}
+
+static const struct of_device_id mp5416_of_match[] = {
+ { .compatible = "mps,mp5416" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, mp5416_of_match);
+
+static const struct i2c_device_id mp5416_id[] = {
+ { "mp5416", },
+ { },
+};
+MODULE_DEVICE_TABLE(i2c, mp5416_id);
+
+static struct i2c_driver mp5416_regulator_driver = {
+ .driver = {
+ .name = "mp5416",
+ .of_match_table = of_match_ptr(mp5416_of_match),
+ },
+ .probe_new = mp5416_i2c_probe,
+ .id_table = mp5416_id,
+};
+module_i2c_driver(mp5416_regulator_driver);
+
+MODULE_AUTHOR("Saravanan Sekar <[email protected]>");
+MODULE_DESCRIPTION("MP5416 PMIC regulator driver");
+MODULE_LICENSE("GPL");
--
2.17.1
Add MAINTAINERS entry for Monolithic Power Systems mp5416 PMIC driver.
Signed-off-by: Saravanan Sekar <[email protected]>
---
MAINTAINERS | 2 ++
1 file changed, 2 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index 9aa438cb9836..e575029f5b89 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -11240,7 +11240,9 @@ F: drivers/tty/mxser.*
MONOLITHIC POWER SYSTEM PMIC DRIVER
M: Saravanan Sekar <[email protected]>
S: Maintained
+F: Documentation/devicetree/bindings/regulator/mps,mp5416.yaml
F: Documentation/devicetree/bindings/regulator/mpq7920.yaml
+F: drivers/regulator/mp5416.c
F: drivers/regulator/mpq7920.c
F: drivers/regulator/mpq7920.h
--
2.17.1
On Wed, Jan 22, 2020 at 02:59:56PM +0100, Saravanan Sekar wrote:
> Add device tree binding information for mp5416 regulator driver.
>
> Signed-off-by: Saravanan Sekar <[email protected]>
> ---
> .../bindings/regulator/mps,mp5416.yaml | 78 +++++++++++++++++++
> 1 file changed, 78 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/regulator/mps,mp5416.yaml
>
> diff --git a/Documentation/devicetree/bindings/regulator/mps,mp5416.yaml b/Documentation/devicetree/bindings/regulator/mps,mp5416.yaml
> new file mode 100644
> index 000000000000..702508e4267f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/regulator/mps,mp5416.yaml
> @@ -0,0 +1,78 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/regulator/mps,mp5416.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Monolithic Power System MP5416 PMIC
> +
> +maintainers:
> + - Saravanan Sekar <[email protected]>
> +
> +properties:
> + $nodename:
> + pattern: "pmic@[0-9a-f]{1,2}"
Needs a ^ and $.
> + compatible:
> + enum:
> + - mps,mp5416
> +
> + reg:
> + maxItems: 1
> +
> + regulators:
> + type: object
> + allOf:
> + - $ref: regulator.yaml#
Does this node contain regulator properties?
> + description: |
> + list of regulators provided by this controller, must be named
> + after their hardware counterparts BUCK[1-4] and LDO[1-4]
> +
> + patternProperties:
> + "^buck[1-4]$":
> + $ref: "regulator.yaml#"
Must be under 'allOf' or other constraints are ignored.
> + type: object
> +
> + "^ldo[1-4]$":
> + $ref: "regulator.yaml#"
> + type: object
> +
> + additionalProperties: false
> + additionalProperties: false
> +
> +required:
> + - compatible
> + - reg
> + - regulators
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + i2c {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pmic@69 {
> + compatible = "mps,mp5416";
> + reg = <0x69>;
> +
> + regulators {
> +
> + buck1 {
> + regulator-name = "buck1";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <2187500>;
> + regulator-min-microamp = <3800000>;
> + regulator-max-microamp = <6800000>;
> + regulator-boot-on;
> + };
> +
> + ldo2 {
> + regulator-name = "ldo2";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <3975000>;
> + };
> + };
> + };
> + };
> +...
> --
> 2.17.1
>