2020-04-03 12:36:27

by Anson Huang

Subject: [PATCH V4] arm64: dts: imx8mp: Add thermal zones support

i.MX8MP has a TMU inside which supports two thermal zones, add support
for them.

Signed-off-by: Anson Huang <[email protected]>
---
Changes since V3:
- Drop some '0x' prefix;
- Add cpufreq cooling for soc thermal zone as well to fit the passive trip point.
---
arch/arm64/boot/dts/freescale/imx8mp.dtsi | 74 +++++++++++++++++++++++++++++++
1 file changed, 74 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mp.dtsi b/arch/arm64/boot/dts/freescale/imx8mp.dtsi
index 9b1616e..77aff14 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mp.dtsi
@@ -7,6 +7,7 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/thermal/thermal.h>

#include "imx8mp-pinfunc.h"

@@ -43,6 +44,7 @@
clocks = <&clk IMX8MP_CLK_ARM>;
enable-method = "psci";
next-level-cache = <&A53_L2>;
+ #cooling-cells = <2>;
};

A53_1: cpu@1 {
@@ -53,6 +55,7 @@
clocks = <&clk IMX8MP_CLK_ARM>;
enable-method = "psci";
next-level-cache = <&A53_L2>;
+ #cooling-cells = <2>;
};

A53_2: cpu@2 {
@@ -63,6 +66,7 @@
clocks = <&clk IMX8MP_CLK_ARM>;
enable-method = "psci";
next-level-cache = <&A53_L2>;
+ #cooling-cells = <2>;
};

A53_3: cpu@3 {
@@ -73,6 +77,7 @@
clocks = <&clk IMX8MP_CLK_ARM>;
enable-method = "psci";
next-level-cache = <&A53_L2>;
+ #cooling-cells = <2>;
};

A53_L2: l2-cache0 {
@@ -127,6 +132,68 @@
method = "smc";
};

+ thermal-zones {
+ cpu-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <2000>;
+ thermal-sensors = <&tmu 0>;
+ trips {
+ cpu_alert0: trip0 {
+ temperature = <85000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu_crit0: trip1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert0>;
+ cooling-device =
+ <&A53_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A53_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A53_2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A53_3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+
+ soc-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <2000>;
+ thermal-sensors = <&tmu 1>;
+ trips {
+ soc_alert0: trip0 {
+ temperature = <85000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ soc_crit0: trip1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&soc_alert0>;
+ cooling-device =
+ <&A53_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A53_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A53_2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A53_3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+ };
+
timer {
compatible = "arm,armv8-timer";
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
@@ -215,6 +282,13 @@
gpio-ranges = <&iomuxc 0 114 30>;
};

+ tmu: tmu@30260000 {
+ compatible = "fsl,imx8mp-tmu";
+ reg = <0x30260000 0x10000>;
+ clocks = <&clk IMX8MP_CLK_TSENSOR_ROOT>;
+ #thermal-sensor-cells = <1>;
+ };
+
wdog1: watchdog@30280000 {
compatible = "fsl,imx8mp-wdt", "fsl,imx21-wdt";
reg = <0x30280000 0x10000>;
--
2.7.4

2020-04-25 08:18:04

by Shawn Guo

Subject: Re: [PATCH V4] arm64: dts: imx8mp: Add thermal zones support

On Fri, Apr 03, 2020 at 08:03:24PM +0800, Anson Huang wrote:
> i.MX8MP has a TMU inside which supports two thermal zones, add support
> for them.
>
> Signed-off-by: Anson Huang <[email protected]>

Applied, thanks.