2020-05-28 22:57:17

by Ricardo Rivera-Matos

[permalink] [raw]
Subject: [PATCH v12 3/4] dt-bindings: power: Add the bindings for the bq2515x family of chargers.

The BQ2515X family of devices are highly integrated battery management
ICs that integrate the most common functions for wearable devices
namely a charger, an output voltage rail, ADC for battery and system
monitoring, and a push-button controller.

Datasheets:
http://www.ti.com/lit/ds/symlink/bq25150.pdf
http://www.ti.com/lit/ds/symlink/bq25155.pdf

Signed-off-by: Ricardo Rivera-Matos <[email protected]>
---
.../bindings/power/supply/bq2515x.yaml | 91 +++++++++++++++++++
1 file changed, 91 insertions(+)
create mode 100644 Documentation/devicetree/bindings/power/supply/bq2515x.yaml

diff --git a/Documentation/devicetree/bindings/power/supply/bq2515x.yaml b/Documentation/devicetree/bindings/power/supply/bq2515x.yaml
new file mode 100644
index 000000000000..19cb336d581e
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/bq2515x.yaml
@@ -0,0 +1,91 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+# Copyright (C) 2020 Texas Instruments Incorporated
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/power/supply/bq2515x.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: TI bq2515x 500-mA Linear charger family
+
+maintainers:
+ - Dan Murphy <[email protected]>
+ - Ricardo Rivera-Matos <[email protected]>
+
+description: |
+ The BQ2515x family is a highly integrated battery charge management IC that
+ integrates the most common functions for wearable devices, namely a charger,
+ an output voltage rail, ADC for battery and system monitoring, and
+ push-button controller.
+
+ Specifications about the charger can be found at:
+ http://www.ti.com/lit/ds/symlink/bq25150.pdf
+ http://www.ti.com/lit/ds/symlink/bq25155.pdf
+
+properties:
+ compatible:
+ enum:
+ - ti,bq25150
+ - ti,bq25155
+
+ reg:
+ maxItems: 1
+ description: I2C address of the charger.
+
+ ac-detect-gpios:
+ description: |
+ GPIO used for connecting the bq2515x device PG (AC Detect)
+ pin.
+ maxItems: 1
+
+ reset-gpios:
+ description: GPIO used for hardware reset.
+ maxItems: 1
+
+ powerdown-gpios:
+ description: GPIO used for low power mode of IC.
+ maxItems: 1
+
+ charge-enable-gpios:
+ description: GPIO used to turn on and off charging.
+ maxItems: 1
+
+ input-current-limit-microamp:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: Maximum input current in micro Amps.
+ minimum: 50000
+ maximum: 500000
+
+ monitored-battery:
+ $ref: battery.yaml#
+
+required:
+ - compatible
+ - reg
+
+additionalProperties: false
+
+examples:
+ - |
+ bat: battery {
+ compatible = "simple-battery";
+ constant-charge-current-max-microamp = <50000>;
+ precharge-current-microamp = <2500>;
+ constant-charge-voltage-max-microvolt = <4000000>;
+ };
+ #include <dt-bindings/gpio/gpio.h>
+ i2c0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bq25150: charger@6b {
+ compatible = "ti,bq25150";
+ reg = <0x6b>;
+ monitored-battery = <&bat>;
+ input-current-limit-microamp = <100000>;
+
+ ac-detect-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+ powerdown-gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+ charge-enable-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+ };
+ };
--
2.26.2


2020-05-29 22:23:04

by Rob Herring (Arm)

[permalink] [raw]
Subject: Re: [PATCH v12 3/4] dt-bindings: power: Add the bindings for the bq2515x family of chargers.

On Thu, May 28, 2020 at 05:53:49PM -0500, Ricardo Rivera-Matos wrote:
> The BQ2515X family of devices are highly integrated battery management
> ICs that integrate the most common functions for wearable devices
> namely a charger, an output voltage rail, ADC for battery and system
> monitoring, and a push-button controller.
>
> Datasheets:
> http://www.ti.com/lit/ds/symlink/bq25150.pdf
> http://www.ti.com/lit/ds/symlink/bq25155.pdf
>
> Signed-off-by: Ricardo Rivera-Matos <[email protected]>
> ---
> .../bindings/power/supply/bq2515x.yaml | 91 +++++++++++++++++++
> 1 file changed, 91 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/power/supply/bq2515x.yaml
>
> diff --git a/Documentation/devicetree/bindings/power/supply/bq2515x.yaml b/Documentation/devicetree/bindings/power/supply/bq2515x.yaml
> new file mode 100644
> index 000000000000..19cb336d581e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/power/supply/bq2515x.yaml
> @@ -0,0 +1,91 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +# Copyright (C) 2020 Texas Instruments Incorporated
> +%YAML 1.2
> +---
> +$id: "http://devicetree.org/schemas/power/supply/bq2515x.yaml#"
> +$schema: "http://devicetree.org/meta-schemas/core.yaml#"
> +
> +title: TI bq2515x 500-mA Linear charger family
> +
> +maintainers:
> + - Dan Murphy <[email protected]>
> + - Ricardo Rivera-Matos <[email protected]>
> +
> +description: |
> + The BQ2515x family is a highly integrated battery charge management IC that
> + integrates the most common functions for wearable devices, namely a charger,
> + an output voltage rail, ADC for battery and system monitoring, and
> + push-button controller.
> +
> + Specifications about the charger can be found at:
> + http://www.ti.com/lit/ds/symlink/bq25150.pdf
> + http://www.ti.com/lit/ds/symlink/bq25155.pdf
> +
> +properties:
> + compatible:
> + enum:
> + - ti,bq25150
> + - ti,bq25155
> +
> + reg:
> + maxItems: 1
> + description: I2C address of the charger.
> +
> + ac-detect-gpios:
> + description: |
> + GPIO used for connecting the bq2515x device PG (AC Detect)
> + pin.
> + maxItems: 1
> +
> + reset-gpios:
> + description: GPIO used for hardware reset.
> + maxItems: 1
> +
> + powerdown-gpios:
> + description: GPIO used for low power mode of IC.
> + maxItems: 1
> +
> + charge-enable-gpios:
> + description: GPIO used to turn on and off charging.
> + maxItems: 1
> +
> + input-current-limit-microamp:
> + $ref: /schemas/types.yaml#/definitions/uint32
> + description: Maximum input current in micro Amps.
> + minimum: 50000
> + maximum: 500000
> +
> + monitored-battery:
> + $ref: battery.yaml#

This doesn't work. It's saying monitored-battery is a node containing
all the properties in battery.yaml.

> +
> +required:
> + - compatible
> + - reg

How is the battery optional?

> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + bat: battery {
> + compatible = "simple-battery";
> + constant-charge-current-max-microamp = <50000>;
> + precharge-current-microamp = <2500>;
> + constant-charge-voltage-max-microvolt = <4000000>;
> + };
> + #include <dt-bindings/gpio/gpio.h>
> + i2c0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + bq25150: charger@6b {
> + compatible = "ti,bq25150";
> + reg = <0x6b>;
> + monitored-battery = <&bat>;
> + input-current-limit-microamp = <100000>;
> +
> + ac-detect-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
> + reset-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
> + powerdown-gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
> + charge-enable-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
> + };
> + };
> --
> 2.26.2
>