changes v8:
- resend correct changes
changes v7:
- VT7: reorder node alphabetically
- VT7: rename "reg_12v_bl: regulator-bl-12v" to "reg_bl_12v0: regulator-bl-12v0"
- VT7: remove panel and TS nodes. This drivers are currently not
mainline.
- prti6q.dtsi: move reg_1v8 to prti6q.dts
- prti6q.dtsi: remove pinctrl from the can1 node. It is done on almost
every board file.
changes v6:
- move fsl.yaml changes to separate patch
- remove partitions, they are provided by the bootloader
- update flash compatible
- rename can3 to can
- fix fsl,mode
- fix interrupt in the wlan node on PRTI6Q
changes v5:
- PRTI6Q: remove status from the pwm-backlight node
- drop the vendor-prefixes patch, it is already taken by Rob
- add Reviewed-by: Rob Herring <[email protected]>
changes v4:
- VT7: fix typo
changes v3:
- move compatible to the start of node
- move status to the end
- use generic names in compatible
- refactor dts/dtsi
- use alphabet order for pinctrl and phandels
- remove unused or currently not supported nodes
changes v2:
- squash PRTI6Q patches
Oleksij Rempel (5):
ARM: dts: add Protonic PRTI6Q board
ARM: dts: add Protonic WD2 board
ARM: dts: add Protonic VT7 board
ARM: dts: add Protonic RVT board
dt-bindings: arm: fsl: add different Protonic boards
.../devicetree/bindings/arm/fsl.yaml | 4 +
arch/arm/boot/dts/Makefile | 4 +
arch/arm/boot/dts/imx6dl-prtrvt.dts | 182 ++++++
arch/arm/boot/dts/imx6dl-prtvt7.dts | 411 +++++++++++++
arch/arm/boot/dts/imx6q-prti6q.dts | 541 ++++++++++++++++++
arch/arm/boot/dts/imx6q-prtwd2.dts | 188 ++++++
arch/arm/boot/dts/imx6qdl-prti6q.dtsi | 165 ++++++
7 files changed, 1495 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-prtrvt.dts
create mode 100644 arch/arm/boot/dts/imx6dl-prtvt7.dts
create mode 100644 arch/arm/boot/dts/imx6q-prti6q.dts
create mode 100644 arch/arm/boot/dts/imx6q-prtwd2.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-prti6q.dtsi
--
2.26.2
Protonic RVT is an internal development platform for a wireless ISObus
Virtual Terminal based on COTS tablets, and the predecessor of the WD2
platform.
Reviewed-by: Rob Herring <[email protected]>
Signed-off-by: David Jander <[email protected]>
Signed-off-by: Oleksij Rempel <[email protected]>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-prtrvt.dts | 182 ++++++++++++++++++++++++++++
2 files changed, 183 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-prtrvt.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 66ee89e7929f9..89842a034e4ba 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -450,6 +450,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-pico-hobbit.dtb \
imx6dl-pico-nymph.dtb \
imx6dl-pico-pi.dtb \
+ imx6dl-prtrvt.dtb \
imx6dl-prtvt7.dtb \
imx6dl-rex-basic.dtb \
imx6dl-riotboard.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-prtrvt.dts b/arch/arm/boot/dts/imx6dl-prtrvt.dts
new file mode 100644
index 0000000000000..b7721e52a463a
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-prtrvt.dts
@@ -0,0 +1,182 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-prti6q.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Protonic RVT board";
+ compatible = "prt,prtrvt", "fsl,imx6dl";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x10000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ led-debug0 {
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&can1 {
+ pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>;
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
+
+&ecspi3 {
+ cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3>;
+ status = "okay";
+
+ nfc@0 {
+ compatible = "ti,trf7970a";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_nfc>;
+ spi-max-frequency = <2000000>;
+ interrupts-extended = <&gpio5 14 IRQ_TYPE_LEVEL_LOW>;
+ ti,enable-gpios = <&gpio5 12 GPIO_ACTIVE_LOW>,
+ <&gpio5 11 GPIO_ACTIVE_LOW>;
+ vin-supply = <®_3v3>;
+ vin-voltage-override = <3100000>;
+ autosuspend-delay = <30000>;
+ irq-status-read-quirk;
+ en2-rf-quirk;
+ t5t-rmb-extra-byte-quirk;
+ status = "okay";
+ };
+};
+
+&i2c3 {
+ adc@49 {
+ compatible = "ti,ads1015";
+ reg = <0x49>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* nc */
+ channel@4 {
+ reg = <4>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* nc */
+ channel@5 {
+ reg = <5>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* can1_l */
+ channel@6 {
+ reg = <6>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* can1_h */
+ channel@7 {
+ reg = <7>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+ };
+
+ rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&usbh1 {
+ status = "disabled";
+};
+
+&vpu {
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl_can1phy: can1phy {
+ fsl,pins = <
+ /* CAN1_SR */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
+ /* CAN1_TERM */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ /* CS */
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
+ MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
+ MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
+ MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x000b1
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ >;
+ };
+
+ pinctrl_nfc: nfcgrp {
+ fsl,pins = <
+ /* NFC_ASK_OOK */
+ MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09 0x100b1
+ /* NFC_PWR_EN */
+ MX6QDL_PAD_DISP0_DAT16__GPIO5_IO10 0x100b1
+ /* NFC_EN2 */
+ MX6QDL_PAD_DISP0_DAT17__GPIO5_IO11 0x100b1
+ /* NFC_EN */
+ MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12 0x100b1
+ /* NFC_MOD */
+ MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13 0x100b1
+ /* NFC_IRQ */
+ MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14 0x100b1
+ >;
+ };
+};
--
2.26.2
Protonic PRTI6Q is a development board and a base class for different
specific customer application boards based on the i.MX6 family of SoCs,
developed by Protonic Holland.
Reviewed-by: Rob Herring <[email protected]>
Signed-off-by: David Jander <[email protected]>
Signed-off-by: Oleksij Rempel <[email protected]>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-prti6q.dts | 541 ++++++++++++++++++++++++++
arch/arm/boot/dts/imx6qdl-prti6q.dtsi | 165 ++++++++
3 files changed, 707 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-prti6q.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-prti6q.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e8dd992013973..206a36a50575e 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -538,6 +538,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-pico-nymph.dtb \
imx6q-pico-pi.dtb \
imx6q-pistachio.dtb \
+ imx6q-prti6q.dtb \
imx6q-rex-pro.dtb \
imx6q-sabreauto.dtb \
imx6q-sabrelite.dtb \
diff --git a/arch/arm/boot/dts/imx6q-prti6q.dts b/arch/arm/boot/dts/imx6q-prti6q.dts
new file mode 100644
index 0000000000000..d8ea9a3f415a8
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-prti6q.dts
@@ -0,0 +1,541 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-prti6q.dtsi"
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+ model = "Protonic PRTI6Q board";
+ compatible = "prt,prti6q", "fsl,imx6q";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0xf0000000>;
+ };
+
+ backlight_lcd: backlight-lcd {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_backlight>;
+ pwms = <&pwm1 0 5000000>;
+ brightness-levels = <0 16 64 255>;
+ num-interpolated-steps = <16>;
+ default-brightness-level = <16>;
+ power-supply = <®_3v3>;
+ enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+ };
+
+ can_osc: can-osc {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ led-debug0 {
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led-debug1 {
+ function = LED_FUNCTION_SD;
+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "disk-activity";
+ };
+ };
+
+ panel {
+ compatible = "kyo,tcg121xglp";
+ backlight = <&backlight_lcd>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+
+ reg_1v8: regulator-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ reg_wifi: regulator-wifi {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wifi_npd>;
+ enable-active-high;
+ gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+ regulator-max-microvolt = <1800000>;
+ regulator-min-microvolt = <1800000>;
+ regulator-name = "regulator-WL12xx";
+ startup-delay-us = <70000>;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "prti6q-sgtl5000";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,widgets =
+ "Microphone", "Microphone Jack",
+ "Line", "Line In Jack",
+ "Headphone", "Headphone Jack",
+ "Speaker", "External Speaker";
+ simple-audio-card,routing =
+ "MIC_IN", "Microphone Jack",
+ "LINE_IN", "Line In Jack",
+ "Headphone Jack", "HP_OUT",
+ "External Speaker", "LINE_OUT";
+
+ simple-audio-card,cpu {
+ sound-dai = <&ssi1>;
+ system-clock-frequency = <0>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&sgtl5000>;
+ bitclock-master;
+ frame-master;
+ };
+ };
+
+ sound-spdif {
+ compatible = "fsl,imx-audio-spdif";
+ model = "imx-spdif";
+ spdif-controller = <&spdif>;
+ spdif-in;
+ spdif-out;
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+
+ mux_ssi1 {
+ fsl,audmux-port = <0>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN 0
+ IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
+ IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
+ IMX_AUDMUX_V2_PTCR_TFSDIR 0
+ IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
+ >;
+ };
+
+ mux_pins3 {
+ fsl,audmux-port = <2>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
+ 0 IMX_AUDMUX_V2_PDCR_TXRXEN
+ >;
+ };
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can2>;
+ status = "okay";
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ };
+};
+
+&ecspi2 {
+ cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>, <&gpio4 25 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2 &pinctrl_ecspi2_cs>;
+ status = "okay";
+
+ can@0 {
+ compatible = "microchip,mcp2515";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can3>;
+ clocks = <&can_osc>;
+ interrupts-extended = <&gpio3 20 IRQ_TYPE_LEVEL_LOW>;
+ spi-max-frequency = <5000000>;
+ };
+
+ adc@1 {
+ compatible = "ti,adc128s052";
+ reg = <1>;
+ spi-max-frequency = <2000000>;
+ vref-supply = <®_3v3>;
+ };
+};
+
+&ecspi3 {
+ cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3>;
+ status = "okay";
+};
+
+&can1 {
+ pinctrl-0 = <&pinctrl_can1>;
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii-id";
+ phy-handle = <&rgmii_phy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip KSZ9031RNX PHY */
+ rgmii_phy: ethernet-phy@0 {
+ reg = <0>;
+ interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&hdmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hdmi>;
+ ddc-i2c-bus = <&i2c2>;
+ status = "okay";
+};
+
+&i2c1 {
+ sgtl5000: audio-codec@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0xa>;
+ #sound-dai-cells = <0>;
+ clocks = <&clks 201>;
+ VDDA-supply = <®_3v3>;
+ VDDIO-supply = <®_3v3>;
+ VDDD-supply = <®_1v8>;
+ };
+};
+
+/* DDC */
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&i2c3 {
+ adc@49 {
+ compatible = "ti,ads1015";
+ reg = <0x49>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* can2_l */
+ channel@4 {
+ reg = <4>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* can2_h */
+ channel@5 {
+ reg = <5>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* can1_l */
+ channel@6 {
+ reg = <6>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* can1_h */
+ channel@7 {
+ reg = <7>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel@0 {
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&sata {
+ status = "okay";
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&spdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spdif>;
+ status = "okay";
+};
+
+&ssi1 {
+ #sound-dai-cells = <0>;
+ fsl,mode = "ac97-slave";
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "okay";
+};
+
+&usbotg {
+ pinctrl-0 = <&pinctrl_usbotg &pinctrl_usbotg_id>;
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ non-removable;
+ vmmc-supply = <®_wifi>;
+ cap-power-off-card;
+ keep-power-in-suspend;
+ status = "okay";
+
+ wifi {
+ compatible = "ti,wl1271";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wifi>;
+ interrupts-extended = <&gpio1 30 IRQ_TYPE_LEVEL_HIGH>;
+ ref-clock-frequency = "38400000";
+ tcxo-clock-frequency = "19200000";
+ };
+};
+
+&iomuxc {
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
+ MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
+ MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
+ MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
+ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
+ >;
+ };
+
+ pinctrl_backlight: backlightgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
+ >;
+ };
+
+ pinctrl_can2: can2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x80000000
+ MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x80000000
+ >;
+ };
+
+ pinctrl_can3: can3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ /* CS */
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
+ MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
+ MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
+ MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
+ >;
+ };
+
+ pinctrl_ecspi2_cs: ecspi2csgrp {
+ fsl,pins = <
+ /* ADC128S022 CS */
+ MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x1b0b1
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
+ MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
+ MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
+ MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x000b1
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
+
+ /* Phy reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
+ >;
+ };
+
+ pinctrl_hdmi: hdmigrp {
+ fsl,pins = <
+ /* NOTE: DDC is done via I2C2, so DON'T
+ * configure DDC pins for HDMI!
+ */
+ MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1f8b0
+ >;
+ };
+
+ /* DDC */
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
+ >;
+ };
+
+ pinctrl_spdif: spdifgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_16__SPDIF_IN 0x1b0b0
+ MX6QDL_PAD_GPIO_19__SPDIF_OUT 0x1b0b0
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D26__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D27__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x1b0b1
+ MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg_id: usbotgidgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1f058
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_wifi: wifigrp {
+ fsl,pins = <
+ /* WL12xx IRQ */
+ MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x10880
+ >;
+ };
+
+ pinctrl_wifi_npd: wifinpd {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b8b0
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6qdl-prti6q.dtsi b/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
new file mode 100644
index 0000000000000..b9ac70b9a4513
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
@@ -0,0 +1,165 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_usb_h1_vbus: regulator-h1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "h1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_usb_otg_vbus: regulator-otg-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "otg-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ temperature-sensor@70 {
+ compatible = "ti,tmp103";
+ reg = <0x70>;
+ };
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usb_h1_vbus>;
+ phy_type = "utmi";
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ phy_type = "utmi";
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_can1: can1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x80000000
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x80000000
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
+ MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
+ MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
+ >;
+ };
+};
--
2.26.2
The Protonic VT7 is a mid-class ISObus Virtual Terminal with a 7 inch
touchscreen display.
Reviewed-by: Rob Herring <[email protected]>
Signed-off-by: Robin van der Gracht <[email protected]>
Signed-off-by: David Jander <[email protected]>
Signed-off-by: Oleksij Rempel <[email protected]>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-prtvt7.dts | 411 ++++++++++++++++++++++++++++
2 files changed, 412 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-prtvt7.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 8ce744f1cbfc9..66ee89e7929f9 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -450,6 +450,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-pico-hobbit.dtb \
imx6dl-pico-nymph.dtb \
imx6dl-pico-pi.dtb \
+ imx6dl-prtvt7.dtb \
imx6dl-rex-basic.dtb \
imx6dl-riotboard.dtb \
imx6dl-sabreauto.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
new file mode 100644
index 0000000000000..083eb72f5fc3d
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -0,0 +1,411 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2016 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-prti6q.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+ model = "Protonic VT7";
+ compatible = "prt,prtvt7", "fsl,imx6dl";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x20000000>;
+ };
+
+ backlight_lcd: backlight-lcd {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_backlight>;
+ pwms = <&pwm1 0 500000>;
+ brightness-levels = <0 20 81 248 1000>;
+ default-brightness-level = <20>;
+ num-interpolated-steps = <21>;
+ power-supply = <®_bl_12v0>;
+ enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+ autorepeat;
+
+ esc {
+ label = "GPIO Key ESC";
+ linux,code = <KEY_ESC>;
+ gpios = <&gpio_pca 0 GPIO_ACTIVE_LOW>;
+ };
+
+ up {
+ label = "GPIO Key UP";
+ linux,code = <KEY_UP>;
+ gpios = <&gpio_pca 1 GPIO_ACTIVE_LOW>;
+ };
+
+ down {
+ label = "GPIO Key DOWN";
+ linux,code = <KEY_DOWN>;
+ gpios = <&gpio_pca 4 GPIO_ACTIVE_LOW>;
+ };
+
+ enter {
+ label = "GPIO Key Enter";
+ linux,code = <KEY_ENTER>;
+ gpios = <&gpio_pca 3 GPIO_ACTIVE_LOW>;
+ };
+
+ cycle {
+ label = "GPIO Key CYCLE";
+ linux,code = <KEY_CYCLEWINDOWS>;
+ gpios = <&gpio_pca 2 GPIO_ACTIVE_LOW>;
+ };
+
+ f1 {
+ label = "GPIO Key F1";
+ linux,code = <KEY_F1>;
+ gpios = <&gpio_pca 14 GPIO_ACTIVE_LOW>;
+ };
+
+ f2 {
+ label = "GPIO Key F2";
+ linux,code = <KEY_F2>;
+ gpios = <&gpio_pca 13 GPIO_ACTIVE_LOW>;
+ };
+
+ f3 {
+ label = "GPIO Key F3";
+ linux,code = <KEY_F3>;
+ gpios = <&gpio_pca 12 GPIO_ACTIVE_LOW>;
+ };
+
+ f4 {
+ label = "GPIO Key F4";
+ linux,code = <KEY_F4>;
+ gpios = <&gpio_pca 11 GPIO_ACTIVE_LOW>;
+ };
+
+ f5 {
+ label = "GPIO Key F5";
+ linux,code = <KEY_F5>;
+ gpios = <&gpio_pca 10 GPIO_ACTIVE_LOW>;
+ };
+
+ f6 {
+ label = "GPIO Key F6";
+ linux,code = <KEY_F6>;
+ gpios = <&gpio_pca 5 GPIO_ACTIVE_LOW>;
+ };
+
+ f7 {
+ label = "GPIO Key F7";
+ linux,code = <KEY_F7>;
+ gpios = <&gpio_pca 6 GPIO_ACTIVE_LOW>;
+ };
+
+ f8 {
+ label = "GPIO Key F8";
+ linux,code = <KEY_F8>;
+ gpios = <&gpio_pca 7 GPIO_ACTIVE_LOW>;
+ };
+
+ f9 {
+ label = "GPIO Key F9";
+ linux,code = <KEY_F9>;
+ gpios = <&gpio_pca 8 GPIO_ACTIVE_LOW>;
+ };
+
+ f10 {
+ label = "GPIO Key F10";
+ linux,code = <KEY_F10>;
+ gpios = <&gpio_pca 9 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ led-debug0 {
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ reg_bl_12v0: regulator-bl-12v0 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_bl_12v0>;
+ regulator-name = "bl-12v0";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_1v8: regulator-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "prti6q-sgtl5000";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,widgets =
+ "Microphone", "Microphone Jack",
+ "Line", "Line In Jack",
+ "Headphone", "Headphone Jack",
+ "Speaker", "External Speaker";
+ simple-audio-card,routing =
+ "MIC_IN", "Microphone Jack",
+ "LINE_IN", "Line In Jack",
+ "Headphone Jack", "HP_OUT",
+ "External Speaker", "LINE_OUT";
+
+ simple-audio-card,cpu {
+ sound-dai = <&ssi1>;
+ system-clock-frequency = <0>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&sgtl5000>;
+ bitclock-master;
+ frame-master;
+ };
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+
+ mux_ssi1 {
+ fsl,audmux-port = <0>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN 0
+ IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
+ IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
+ IMX_AUDMUX_V2_PTCR_TFSDIR 0
+ IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
+ >;
+ };
+
+ mux_pins3 {
+ fsl,audmux-port = <2>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
+ 0 IMX_AUDMUX_V2_PDCR_TXRXEN
+ >;
+ };
+};
+
+&can1 {
+ pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>;
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
+};
+
+&ecspi2 {
+ cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ status = "okay";
+};
+
+&i2c1 {
+ sgtl5000: codec@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0xa>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_codec>;
+ #sound-dai-cells = <0>;
+ clocks = <&clks 201>;
+ VDDA-supply = <®_3v3>;
+ VDDIO-supply = <®_3v3>;
+ VDDD-supply = <®_1v8>;
+ };
+};
+
+&i2c3 {
+ rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+
+ gpio_pca: gpio@74 {
+ compatible = "nxp,pca9539";
+ reg = <0x74>;
+ interrupts-extended = <&gpio4 5 IRQ_TYPE_LEVEL_LOW>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+};
+
+&ipu1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1_csi0>;
+ status = "okay";
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&snvs_pwrkey {
+ status = "okay";
+};
+
+&ssi1 {
+ #sound-dai-cells = <0>;
+ fsl,mode = "i2s-slave";
+ status = "okay";
+};
+
+&usbh1 {
+ status = "disabled";
+};
+
+&vpu {
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
+ MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
+ MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
+ MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
+ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
+ >;
+ };
+
+ pinctrl_backlight: backlightgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
+ >;
+ };
+
+ pinctrl_can1phy: can1phy {
+ fsl,pins = <
+ /* CAN1_SR */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
+ /* CAN1_TERM */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
+ >;
+ };
+
+ pinctrl_codec: codecgrp {
+ fsl,pins = <
+ /* AUDIO_nRESET */
+ MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
+ MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
+ MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
+ MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
+ >;
+ };
+
+ pinctrl_ipu1_csi0: ipu1csi0grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
+ MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
+ /* ITU656_nRESET */
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+ /* ITU656_nPDN */
+ MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
+ >;
+ };
+
+ pinctrl_ipu1_disp: ipudisp1grp {
+ fsl,pins = <
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0xb0
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0xb0
+
+ MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0xb0
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0xb0
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0xb0
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0xb0
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0xb0
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0xb0
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0xb0
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0xb0
+
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0xb0
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0xb0
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0xb0
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0xb0
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0xb0
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0xb0
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0xb0
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0xb0
+
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0xb0
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0xb0
+ MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0xb0
+ MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0xb0
+ MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0xb0
+ MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0xb0
+ MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0xb0
+ MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0xb0
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b0
+ >;
+ };
+
+ pinctrl_reg_bl_12v0: 12blgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x1b0b0
+ >;
+ };
+
+ pinctrl_tsc: tscgrp {
+
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b0
+ MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
+ >;
+ };
+};
--
2.26.2
On Wed, May 20, 2020 at 05:41:12PM +0200, Oleksij Rempel wrote:
> Protonic PRTI6Q is a development board and a base class for different
> specific customer application boards based on the i.MX6 family of SoCs,
> developed by Protonic Holland.
>
> Reviewed-by: Rob Herring <[email protected]>
> Signed-off-by: David Jander <[email protected]>
> Signed-off-by: Oleksij Rempel <[email protected]>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx6q-prti6q.dts | 541 ++++++++++++++++++++++++++
> arch/arm/boot/dts/imx6qdl-prti6q.dtsi | 165 ++++++++
> 3 files changed, 707 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6q-prti6q.dts
> create mode 100644 arch/arm/boot/dts/imx6qdl-prti6q.dtsi
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index e8dd992013973..206a36a50575e 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -538,6 +538,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6q-pico-nymph.dtb \
> imx6q-pico-pi.dtb \
> imx6q-pistachio.dtb \
> + imx6q-prti6q.dtb \
> imx6q-rex-pro.dtb \
> imx6q-sabreauto.dtb \
> imx6q-sabrelite.dtb \
> diff --git a/arch/arm/boot/dts/imx6q-prti6q.dts b/arch/arm/boot/dts/imx6q-prti6q.dts
> new file mode 100644
> index 0000000000000..d8ea9a3f415a8
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-prti6q.dts
> @@ -0,0 +1,541 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/*
> + * Copyright (c) 2014 Protonic Holland
> + */
> +
> +/dts-v1/;
> +#include "imx6q.dtsi"
> +#include "imx6qdl-prti6q.dtsi"
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/sound/fsl-imx-audmux.h>
> +
> +/ {
> + model = "Protonic PRTI6Q board";
> + compatible = "prt,prti6q", "fsl,imx6q";
Undocumented compatible?
> +
> + memory@10000000 {
> + device_type = "memory";
> + reg = <0x10000000 0xf0000000>;
> + };
> +
> + backlight_lcd: backlight-lcd {
> + compatible = "pwm-backlight";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_backlight>;
> + pwms = <&pwm1 0 5000000>;
> + brightness-levels = <0 16 64 255>;
> + num-interpolated-steps = <16>;
> + default-brightness-level = <16>;
It should be an index into brightness-levels.
> + power-supply = <®_3v3>;
> + enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
> + };
> +
> + can_osc: can-osc {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <25000000>;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_leds>;
> +
> + led-debug0 {
> + function = LED_FUNCTION_STATUS;
> + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> +
> + led-debug1 {
> + function = LED_FUNCTION_SD;
> + gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "disk-activity";
> + };
> + };
> +
> + panel {
> + compatible = "kyo,tcg121xglp";
> + backlight = <&backlight_lcd>;
> +
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&lvds0_out>;
> + };
> + };
> + };
> +
> + reg_1v8: regulator-1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
What's the point of having always-on property for a regulator without
on/off control?
> + };
> +
> + reg_wifi: regulator-wifi {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_wifi_npd>;
> + enable-active-high;
> + gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
> + regulator-max-microvolt = <1800000>;
> + regulator-min-microvolt = <1800000>;
> + regulator-name = "regulator-WL12xx";
> + startup-delay-us = <70000>;
> + };
> +
> + sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,name = "prti6q-sgtl5000";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,widgets =
> + "Microphone", "Microphone Jack",
> + "Line", "Line In Jack",
> + "Headphone", "Headphone Jack",
> + "Speaker", "External Speaker";
> + simple-audio-card,routing =
> + "MIC_IN", "Microphone Jack",
> + "LINE_IN", "Line In Jack",
> + "Headphone Jack", "HP_OUT",
> + "External Speaker", "LINE_OUT";
> +
> + simple-audio-card,cpu {
> + sound-dai = <&ssi1>;
> + system-clock-frequency = <0>;
> + };
> +
> + simple-audio-card,codec {
> + sound-dai = <&sgtl5000>;
> + bitclock-master;
> + frame-master;
> + };
> + };
> +
> + sound-spdif {
> + compatible = "fsl,imx-audio-spdif";
> + model = "imx-spdif";
> + spdif-controller = <&spdif>;
> + spdif-in;
> + spdif-out;
> + };
> +};
> +
> +&audmux {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_audmux>;
> + status = "okay";
> +
> + mux_ssi1 {
We recommend to use hyphen than underscore in node name.
> + fsl,audmux-port = <0>;
> + fsl,port-config = <
> + IMX_AUDMUX_V2_PTCR_SYN 0
> + IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
> + IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
> + IMX_AUDMUX_V2_PTCR_TFSDIR 0
> + IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
> + >;
> + };
> +
> + mux_pins3 {
> + fsl,audmux-port = <2>;
> + fsl,port-config = <
> + IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
> + 0 IMX_AUDMUX_V2_PDCR_TXRXEN
> + >;
> + };
> +};
> +
> +&can2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_can2>;
> + status = "okay";
> +};
> +
> +&ecspi1 {
> + cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi1>;
> + status = "okay";
> +
> + flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <20000000>;
> + };
> +};
> +
> +&ecspi2 {
> + cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>, <&gpio4 25 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi2 &pinctrl_ecspi2_cs>;
> + status = "okay";
> +
> + can@0 {
> + compatible = "microchip,mcp2515";
> + reg = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_can3>;
> + clocks = <&can_osc>;
> + interrupts-extended = <&gpio3 20 IRQ_TYPE_LEVEL_LOW>;
> + spi-max-frequency = <5000000>;
> + };
> +
> + adc@1 {
> + compatible = "ti,adc128s052";
> + reg = <1>;
> + spi-max-frequency = <2000000>;
> + vref-supply = <®_3v3>;
> + };
> +};
> +
> +&ecspi3 {
> + cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi3>;
> + status = "okay";
> +};
> +
> +&can1 {
It's out of alphabetic order.
> + pinctrl-0 = <&pinctrl_can1>;
> +};
> +
> +&fec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_enet>;
> + phy-mode = "rgmii-id";
> + phy-handle = <&rgmii_phy>;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* Microchip KSZ9031RNX PHY */
> + rgmii_phy: ethernet-phy@0 {
> + reg = <0>;
> + interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
> + reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
> + reset-assert-us = <10000>;
> + reset-deassert-us = <300>;
> + };
> + };
> +};
> +
> +&hdmi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hdmi>;
> + ddc-i2c-bus = <&i2c2>;
> + status = "okay";
> +};
> +
> +&i2c1 {
> + sgtl5000: audio-codec@a {
> + compatible = "fsl,sgtl5000";
> + reg = <0xa>;
> + #sound-dai-cells = <0>;
> + clocks = <&clks 201>;
> + VDDA-supply = <®_3v3>;
> + VDDIO-supply = <®_3v3>;
> + VDDD-supply = <®_1v8>;
> + };
> +};
> +
> +/* DDC */
> +&i2c2 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + status = "okay";
> +};
> +
> +&i2c3 {
> + adc@49 {
> + compatible = "ti,ads1015";
> + reg = <0x49>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* can2_l */
> + channel@4 {
> + reg = <4>;
> + ti,gain = <3>;
> + ti,datarate = <3>;
> + };
> +
> + /* can2_h */
> + channel@5 {
> + reg = <5>;
> + ti,gain = <3>;
> + ti,datarate = <3>;
> + };
> +
> + /* can1_l */
> + channel@6 {
> + reg = <6>;
> + ti,gain = <3>;
> + ti,datarate = <3>;
> + };
> +
> + /* can1_h */
> + channel@7 {
> + reg = <7>;
> + ti,gain = <3>;
> + ti,datarate = <3>;
> + };
> + };
> +};
> +
> +&pcie {
> + status = "okay";
> +};
> +
> +&pwm1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm1>;
> + status = "okay";
> +};
> +
> +&ldb {
> + status = "okay";
> +
> + lvds-channel@0 {
> + status = "okay";
> +
> + port@4 {
> + reg = <4>;
> +
> + lvds0_out: endpoint {
> + remote-endpoint = <&panel_in>;
> + };
> + };
> + };
> +};
> +
> +&sata {
> + status = "okay";
> +};
> +
> +&snvs_poweroff {
> + status = "okay";
> +};
> +
> +&spdif {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_spdif>;
> + status = "okay";
> +};
> +
> +&ssi1 {
> + #sound-dai-cells = <0>;
> + fsl,mode = "ac97-slave";
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + status = "okay";
> +};
> +
> +&uart5 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart5>;
> + status = "okay";
> +};
> +
> +&usbotg {
> + pinctrl-0 = <&pinctrl_usbotg &pinctrl_usbotg_id>;
> +};
> +
> +&usdhc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc2>;
> + non-removable;
> + vmmc-supply = <®_wifi>;
> + cap-power-off-card;
> + keep-power-in-suspend;
> + status = "okay";
> +
> + wifi {
> + compatible = "ti,wl1271";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_wifi>;
> + interrupts-extended = <&gpio1 30 IRQ_TYPE_LEVEL_HIGH>;
> + ref-clock-frequency = "38400000";
> + tcxo-clock-frequency = "19200000";
> + };
> +};
> +
> +&iomuxc {
> + pinctrl_audmux: audmuxgrp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
> + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
> + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
> + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
> + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
> + >;
> + };
> +
> + pinctrl_backlight: backlightgrp {
> + fsl,pins = <
> + MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
> + >;
> + };
> +
> + pinctrl_can2: can2grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x80000000
> + MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x80000000
Code proper pin configuration value.
> + >;
> + };
> +
> + pinctrl_can3: can3grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1
> + >;
> + };
> +
> + pinctrl_ecspi1: ecspi1grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
> + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
> + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
> + /* CS */
> + MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
> + >;
> + };
> +
> + pinctrl_ecspi2: ecspi2grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
> + MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
> + MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
> + MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
> + >;
> + };
> +
> + pinctrl_ecspi2_cs: ecspi2csgrp {
> + fsl,pins = <
> + /* ADC128S022 CS */
> + MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x1b0b1
> + >;
> + };
> +
> + pinctrl_ecspi3: ecspi3grp {
> + fsl,pins = <
> + MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
> + MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
> + MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
> + MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x000b1
> + >;
> + };
> +
> + pinctrl_enet: enetgrp {
> + fsl,pins = <
> + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
> + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
> + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
> + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
> + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
> + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
> + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
> + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
> + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
> + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
> + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
> + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
> + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
> + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
> + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
> +
> + /* Phy reset */
> + MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
> + MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
> + >;
> + };
> +
> + pinctrl_hdmi: hdmigrp {
> + fsl,pins = <
> + /* NOTE: DDC is done via I2C2, so DON'T
> + * configure DDC pins for HDMI!
> + */
> + MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1f8b0
> + >;
> + };
> +
> + /* DDC */
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
> + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_leds: ledsgrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
> + MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
> + >;
> + };
> +
> + pinctrl_pwm1: pwm1grp {
> + fsl,pins = <
> + MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
> + >;
> + };
> +
> + pinctrl_spdif: spdifgrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_16__SPDIF_IN 0x1b0b0
> + MX6QDL_PAD_GPIO_19__SPDIF_OUT 0x1b0b0
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D26__UART2_RX_DATA 0x1b0b1
> + MX6QDL_PAD_EIM_D27__UART2_TX_DATA 0x1b0b1
> + MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x1b0b1
> + MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B 0x1b0b1
> + >;
> + };
> +
> + pinctrl_uart5: uart5grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
> + MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
> + >;
> + };
> +
> + pinctrl_usbotg_id: usbotgidgrp {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1f058
> + >;
> + };
> +
> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
> + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
> + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
> + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
> + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
> + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
> + >;
> + };
> +
> + pinctrl_wifi: wifigrp {
> + fsl,pins = <
> + /* WL12xx IRQ */
> + MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x10880
> + >;
> + };
> +
> + pinctrl_wifi_npd: wifinpd {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b8b0
> + >;
> + };
> +};
> diff --git a/arch/arm/boot/dts/imx6qdl-prti6q.dtsi b/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
> new file mode 100644
> index 0000000000000..b9ac70b9a4513
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
> @@ -0,0 +1,165 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/*
> + * Copyright (c) 2014 Protonic Holland
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> + chosen {
> + stdout-path = &uart4;
> + };
> +
> + reg_3v3: regulator-3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + reg_usb_h1_vbus: regulator-h1-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "h1-vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + };
> +
> + reg_usb_otg_vbus: regulator-otg-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "otg-vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +};
> +
> +&can1 {
> + pinctrl-names = "default";
> + status = "okay";
It doesn't make a lot of sense and hurts the readability. Merge it
into can1 in imx6q-prti6q.dts.
Shawn
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +};
> +
> +&i2c3 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c3>;
> + status = "okay";
> +
> + temperature-sensor@70 {
> + compatible = "ti,tmp103";
> + reg = <0x70>;
> + };
> +};
> +
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart4>;
> + status = "okay";
> +};
> +
> +&usbh1 {
> + vbus-supply = <®_usb_h1_vbus>;
> + phy_type = "utmi";
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +&usbotg {
> + vbus-supply = <®_usb_otg_vbus>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg>;
> + phy_type = "utmi";
> + dr_mode = "host";
> + disable-over-current;
> + status = "okay";
> +};
> +
> +&usdhc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc1>;
> + cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&usdhc3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc3>;
> + bus-width = <8>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_can1: can1grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x80000000
> + MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x80000000
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
> + MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
> + >;
> + };
> +
> + pinctrl_i2c3: i2c3grp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
> + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_uart4: uart4grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
> + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
> + >;
> + };
> +
> + pinctrl_usdhc1: usdhc1grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
> + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
> + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
> + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
> + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
> + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
> + MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
> + >;
> + };
> +
> + pinctrl_usdhc3: usdhc3grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
> + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
> + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
> + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
> + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
> + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
> + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
> + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
> + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
> + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
> + MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
> + >;
> + };
> +
> + pinctrl_usbotg: usbotggrp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
> + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
> + >;
> + };
> +};
> --
> 2.26.2
>
On Wed, May 20, 2020 at 05:41:14PM +0200, Oleksij Rempel wrote:
> The Protonic VT7 is a mid-class ISObus Virtual Terminal with a 7 inch
> touchscreen display.
>
> Reviewed-by: Rob Herring <[email protected]>
> Signed-off-by: Robin van der Gracht <[email protected]>
> Signed-off-by: David Jander <[email protected]>
> Signed-off-by: Oleksij Rempel <[email protected]>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx6dl-prtvt7.dts | 411 ++++++++++++++++++++++++++++
> 2 files changed, 412 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6dl-prtvt7.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 8ce744f1cbfc9..66ee89e7929f9 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -450,6 +450,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6dl-pico-hobbit.dtb \
> imx6dl-pico-nymph.dtb \
> imx6dl-pico-pi.dtb \
> + imx6dl-prtvt7.dtb \
> imx6dl-rex-basic.dtb \
> imx6dl-riotboard.dtb \
> imx6dl-sabreauto.dtb \
> diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
> new file mode 100644
> index 0000000000000..083eb72f5fc3d
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
> @@ -0,0 +1,411 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/*
> + * Copyright (c) 2016 Protonic Holland
> + */
> +
> +/dts-v1/;
> +#include "imx6dl.dtsi"
> +#include "imx6qdl-prti6q.dtsi"
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/sound/fsl-imx-audmux.h>
> +
> +/ {
> + model = "Protonic VT7";
> + compatible = "prt,prtvt7", "fsl,imx6dl";
> +
> + memory@10000000 {
> + device_type = "memory";
> + reg = <0x10000000 0x20000000>;
> + };
> +
> + backlight_lcd: backlight-lcd {
> + compatible = "pwm-backlight";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_backlight>;
> + pwms = <&pwm1 0 500000>;
> + brightness-levels = <0 20 81 248 1000>;
> + default-brightness-level = <20>;
> + num-interpolated-steps = <21>;
> + power-supply = <®_bl_12v0>;
> + enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
> + };
> +
> + keys {
> + compatible = "gpio-keys";
> + autorepeat;
> +
> + esc {
> + label = "GPIO Key ESC";
> + linux,code = <KEY_ESC>;
> + gpios = <&gpio_pca 0 GPIO_ACTIVE_LOW>;
> + };
> +
> + up {
> + label = "GPIO Key UP";
> + linux,code = <KEY_UP>;
> + gpios = <&gpio_pca 1 GPIO_ACTIVE_LOW>;
> + };
> +
> + down {
> + label = "GPIO Key DOWN";
> + linux,code = <KEY_DOWN>;
> + gpios = <&gpio_pca 4 GPIO_ACTIVE_LOW>;
> + };
> +
> + enter {
> + label = "GPIO Key Enter";
> + linux,code = <KEY_ENTER>;
> + gpios = <&gpio_pca 3 GPIO_ACTIVE_LOW>;
> + };
> +
> + cycle {
> + label = "GPIO Key CYCLE";
> + linux,code = <KEY_CYCLEWINDOWS>;
> + gpios = <&gpio_pca 2 GPIO_ACTIVE_LOW>;
> + };
> +
> + f1 {
> + label = "GPIO Key F1";
> + linux,code = <KEY_F1>;
> + gpios = <&gpio_pca 14 GPIO_ACTIVE_LOW>;
> + };
> +
> + f2 {
> + label = "GPIO Key F2";
> + linux,code = <KEY_F2>;
> + gpios = <&gpio_pca 13 GPIO_ACTIVE_LOW>;
> + };
> +
> + f3 {
> + label = "GPIO Key F3";
> + linux,code = <KEY_F3>;
> + gpios = <&gpio_pca 12 GPIO_ACTIVE_LOW>;
> + };
> +
> + f4 {
> + label = "GPIO Key F4";
> + linux,code = <KEY_F4>;
> + gpios = <&gpio_pca 11 GPIO_ACTIVE_LOW>;
> + };
> +
> + f5 {
> + label = "GPIO Key F5";
> + linux,code = <KEY_F5>;
> + gpios = <&gpio_pca 10 GPIO_ACTIVE_LOW>;
> + };
> +
> + f6 {
> + label = "GPIO Key F6";
> + linux,code = <KEY_F6>;
> + gpios = <&gpio_pca 5 GPIO_ACTIVE_LOW>;
> + };
> +
> + f7 {
> + label = "GPIO Key F7";
> + linux,code = <KEY_F7>;
> + gpios = <&gpio_pca 6 GPIO_ACTIVE_LOW>;
> + };
> +
> + f8 {
> + label = "GPIO Key F8";
> + linux,code = <KEY_F8>;
> + gpios = <&gpio_pca 7 GPIO_ACTIVE_LOW>;
> + };
> +
> + f9 {
> + label = "GPIO Key F9";
> + linux,code = <KEY_F9>;
> + gpios = <&gpio_pca 8 GPIO_ACTIVE_LOW>;
> + };
> +
> + f10 {
> + label = "GPIO Key F10";
> + linux,code = <KEY_F10>;
> + gpios = <&gpio_pca 9 GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_leds>;
> +
> + led-debug0 {
> + function = LED_FUNCTION_STATUS;
> + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + reg_bl_12v0: regulator-bl-12v0 {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_bl_12v0>;
> + regulator-name = "bl-12v0";
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_1v8: regulator-1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,name = "prti6q-sgtl5000";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,widgets =
> + "Microphone", "Microphone Jack",
> + "Line", "Line In Jack",
> + "Headphone", "Headphone Jack",
> + "Speaker", "External Speaker";
> + simple-audio-card,routing =
> + "MIC_IN", "Microphone Jack",
> + "LINE_IN", "Line In Jack",
> + "Headphone Jack", "HP_OUT",
> + "External Speaker", "LINE_OUT";
> +
> + simple-audio-card,cpu {
> + sound-dai = <&ssi1>;
> + system-clock-frequency = <0>;
> + };
> +
> + simple-audio-card,codec {
> + sound-dai = <&sgtl5000>;
> + bitclock-master;
> + frame-master;
> + };
> + };
> +};
> +
> +&audmux {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_audmux>;
> + status = "okay";
> +
> + mux_ssi1 {
> + fsl,audmux-port = <0>;
> + fsl,port-config = <
> + IMX_AUDMUX_V2_PTCR_SYN 0
> + IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
> + IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
> + IMX_AUDMUX_V2_PTCR_TFSDIR 0
> + IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
> + >;
> + };
> +
> + mux_pins3 {
> + fsl,audmux-port = <2>;
> + fsl,port-config = <
> + IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
> + 0 IMX_AUDMUX_V2_PDCR_TXRXEN
> + >;
> + };
> +};
> +
> +&can1 {
> + pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>;
> +};
> +
> +&clks {
> + assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
> + assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
> +};
> +
> +&ecspi2 {
> + cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi2>;
> + status = "okay";
> +};
> +
> +&i2c1 {
> + sgtl5000: codec@a {
audio-codec
> + compatible = "fsl,sgtl5000";
> + reg = <0xa>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_codec>;
> + #sound-dai-cells = <0>;
> + clocks = <&clks 201>;
> + VDDA-supply = <®_3v3>;
> + VDDIO-supply = <®_3v3>;
> + VDDD-supply = <®_1v8>;
> + };
> +};
> +
> +&i2c3 {
> + rtc@51 {
> + compatible = "nxp,pcf8563";
> + reg = <0x51>;
> + };
> +
> + gpio_pca: gpio@74 {
> + compatible = "nxp,pca9539";
> + reg = <0x74>;
> + interrupts-extended = <&gpio4 5 IRQ_TYPE_LEVEL_LOW>;
> + #gpio-cells = <2>;
> + gpio-controller;
> + };
> +};
> +
> +&ipu1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ipu1_csi0>;
> + status = "okay";
> +};
> +
> +&pwm1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm1>;
> + status = "okay";
> +};
> +
> +&snvs_poweroff {
> + status = "okay";
> +};
> +
> +&snvs_pwrkey {
> + status = "okay";
> +};
> +
> +&ssi1 {
> + #sound-dai-cells = <0>;
> + fsl,mode = "i2s-slave";
Check bindings doc please.
Shawn
> + status = "okay";
> +};
> +
> +&usbh1 {
> + status = "disabled";
> +};
> +
> +&vpu {
> + status = "disabled";
> +};
> +
> +&iomuxc {
> + pinctrl_audmux: audmuxgrp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
> + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
> + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
> + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
> + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
> + >;
> + };
> +
> + pinctrl_backlight: backlightgrp {
> + fsl,pins = <
> + MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
> + >;
> + };
> +
> + pinctrl_can1phy: can1phy {
> + fsl,pins = <
> + /* CAN1_SR */
> + MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
> + /* CAN1_TERM */
> + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
> + >;
> + };
> +
> + pinctrl_codec: codecgrp {
> + fsl,pins = <
> + /* AUDIO_nRESET */
> + MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0
> + >;
> + };
> +
> + pinctrl_ecspi2: ecspi2grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
> + MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
> + MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
> + MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
> + >;
> + };
> +
> + pinctrl_ipu1_csi0: ipu1csi0grp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
> + MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
> + /* ITU656_nRESET */
> + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
> + /* ITU656_nPDN */
> + MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
> + >;
> + };
> +
> + pinctrl_ipu1_disp: ipudisp1grp {
> + fsl,pins = <
> + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0xb0
> + MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0xb0
> +
> + MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0xb0
> + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0xb0
> + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0xb0
> + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0xb0
> + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0xb0
> + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0xb0
> + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0xb0
> + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0xb0
> +
> + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0xb0
> + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0xb0
> + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0xb0
> + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0xb0
> + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0xb0
> + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0xb0
> + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0xb0
> + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0xb0
> +
> + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0xb0
> + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0xb0
> + MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0xb0
> + MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0xb0
> + MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0xb0
> + MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0xb0
> + MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0xb0
> + MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0xb0
> + >;
> + };
> +
> + pinctrl_leds: ledsgrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
> + >;
> + };
> +
> + pinctrl_pwm1: pwm1grp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b0
> + >;
> + };
> +
> + pinctrl_reg_bl_12v0: 12blgrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x1b0b0
> + >;
> + };
> +
> + pinctrl_tsc: tscgrp {
> +
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b0
> + MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
> + >;
> + };
> +};
> --
> 2.26.2
>