Hello,
This series adds support for MaxLinear/Exar USB to serial converters.
This driver only supports XR21V141X series but it can easily be extended
to other series in future.
This driver is inspired from the initial one submitted by Patong Yang:
https://patchwork.kernel.org/patch/10543261/
While the initial driver was a custom tty USB driver exposing whole
new serial interface ttyXRUSBn, this version is completely based on USB
serial core thus exposing the interfaces as ttyUSBn. This will avoid
the overhead of exposing a new USB serial interface which the userspace
tools are unaware of.
This series has been tested with Hikey970 board hosting XR21V141X chip.
Thanks,
Mani
Changes in v4:
* Multiple improvements based on Johan's review. Noticeable ones are:
- Now the driver claims both control and data interfaces but only registers
tty device for data interface.
- GPIO pin status is now shared between the console and gpiolib
implementations. This is done to avoid changing the lines spuriously.
- A separate port_open flag is added to reject GPIO requests while the tty
port is open.
- Removed padding PID to gpio device.
* Added Greg and Mauro's review and tested tags.
* Included a patch from Mauro to avoid the CDC-ACM driver to claim this device
when this driver is built.
Changes in v3:
* Dropped the check for PID and also the reg_width property.
Changes in v2:
* Dropped the code related to handling variable register size. It's all u8 now.
* Dropped the header file and moved the contents to driver itself.
* Added Linus's reviewed-by tag for gpiochip patch.
* Added PID to gpiochip label
* Dropped gpiochip for interface 0
Manivannan Sadhasivam (2):
usb: serial: Add MaxLinear/Exar USB to Serial driver
usb: serial: xr_serial: Add gpiochip support
Mauro Carvalho Chehab (1):
usb: cdc-acm: Ignore Exar XR21V141X when serial driver is built
drivers/usb/class/cdc-acm.c | 6 +
drivers/usb/serial/Kconfig | 9 +
drivers/usb/serial/Makefile | 1 +
drivers/usb/serial/xr_serial.c | 857 +++++++++++++++++++++++++++++++++
4 files changed, 873 insertions(+)
create mode 100644 drivers/usb/serial/xr_serial.c
--
2.17.1
Add support for MaxLinear/Exar USB to Serial converters. This driver
only supports XR21V141X series but it can be extended to other series
from Exar as well in future.
This driver is inspired from the initial one submitted by Patong Yang:
https://patchwork.kernel.org/patch/10543261/
While the initial driver was a custom tty USB driver exposing whole
new serial interface ttyXRUSBn, this version is completely based on USB
serial core thus exposing the interfaces as ttyUSBn. This will avoid
the overhead of exposing a new USB serial interface which the userspace
tools are unaware of.
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Tested-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Manivannan Sadhasivam <[email protected]>
---
drivers/usb/serial/Kconfig | 9 +
drivers/usb/serial/Makefile | 1 +
drivers/usb/serial/xr_serial.c | 650 +++++++++++++++++++++++++++++++++
3 files changed, 660 insertions(+)
create mode 100644 drivers/usb/serial/xr_serial.c
diff --git a/drivers/usb/serial/Kconfig b/drivers/usb/serial/Kconfig
index 25d7e0c36d38..8f6ad9f94735 100644
--- a/drivers/usb/serial/Kconfig
+++ b/drivers/usb/serial/Kconfig
@@ -644,6 +644,15 @@ config USB_SERIAL_UPD78F0730
To compile this driver as a module, choose M here: the
module will be called upd78f0730.
+config USB_SERIAL_XR
+ tristate "USB MaxLinear/Exar USB to Serial driver"
+ help
+ Say Y here if you want to use MaxLinear/Exar USB to Serial converter
+ devices.
+
+ To compile this driver as a module, choose M here: the
+ module will be called xr_serial.
+
config USB_SERIAL_DEBUG
tristate "USB Debugging Device"
help
diff --git a/drivers/usb/serial/Makefile b/drivers/usb/serial/Makefile
index 2d491e434f11..4f69c2a3aff3 100644
--- a/drivers/usb/serial/Makefile
+++ b/drivers/usb/serial/Makefile
@@ -62,4 +62,5 @@ obj-$(CONFIG_USB_SERIAL_VISOR) += visor.o
obj-$(CONFIG_USB_SERIAL_WISHBONE) += wishbone-serial.o
obj-$(CONFIG_USB_SERIAL_WHITEHEAT) += whiteheat.o
obj-$(CONFIG_USB_SERIAL_XIRCOM) += keyspan_pda.o
+obj-$(CONFIG_USB_SERIAL_XR) += xr_serial.o
obj-$(CONFIG_USB_SERIAL_XSENS_MT) += xsens_mt.o
diff --git a/drivers/usb/serial/xr_serial.c b/drivers/usb/serial/xr_serial.c
new file mode 100644
index 000000000000..bb7df79cc129
--- /dev/null
+++ b/drivers/usb/serial/xr_serial.c
@@ -0,0 +1,650 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * MaxLinear/Exar USB to Serial driver
+ *
+ * Based on initial driver written by Patong Yang <[email protected]>
+ *
+ * This driver claims both data and control interfaces but only registers tty
+ * device for data interface.
+ *
+ * Copyright (c) 2020 Manivannan Sadhasivam <[email protected]>
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/tty.h>
+#include <linux/usb.h>
+#include <linux/usb/serial.h>
+
+static void xr_set_termios(struct tty_struct *tty,
+ struct usb_serial_port *port,
+ struct ktermios *old_termios);
+
+struct xr_uart_regs {
+ u8 enable;
+ u8 format;
+ u8 flow_ctrl;
+ u8 xon_char;
+ u8 xoff_char;
+ u8 loopback;
+ u8 tx_break;
+ u8 rs485_delay;
+ u8 gpio_mode;
+ u8 gpio_dir;
+ u8 gpio_int_mask;
+ u8 gpio_set;
+ u8 gpio_clr;
+ u8 gpio_status;
+};
+
+struct xr_port_private {
+ const struct xr_uart_regs *regs;
+ bool port_open;
+};
+
+struct xr_txrx_clk_mask {
+ u16 tx;
+ u16 rx0;
+ u16 rx1;
+};
+
+#define XR21V141X_ID 0x1410
+#define XR_INT_OSC_HZ 48000000U
+#define XR21V141X_MIN_SPEED 46U
+#define XR21V141X_MAX_SPEED XR_INT_OSC_HZ
+
+/* USB Requests */
+#define XR_SET_XR21V141X 0
+#define XR_GET_XR21V141X 1
+
+#define XR21V141X_CLOCK_DIVISOR_0 0x4
+#define XR21V141X_CLOCK_DIVISOR_1 0x5
+#define XR21V141X_CLOCK_DIVISOR_2 0x6
+#define XR21V141X_TX_CLOCK_MASK_0 0x7
+#define XR21V141X_TX_CLOCK_MASK_1 0x8
+#define XR21V141X_RX_CLOCK_MASK_0 0x9
+#define XR21V141X_RX_CLOCK_MASK_1 0xa
+
+/* XR21V141X register blocks */
+#define XR21V141X_UART_REG_BLOCK 0
+#define XR21V141X_UART_MANAGER_REG_BLOCK 4
+#define XR21V141X_UART_CUSTOM_BLOCK 0x66
+
+/* XR21V141X UART Manager Registers */
+#define XR21V141X_UART_MANAGER_FIFO_ENABLE_REG 0x10
+#define XR21V141X_UART_MANAGER_ENABLE_TX_FIFO 0x1
+#define XR21V141X_UART_MANAGER_ENABLE_RX_FIFO 0x2
+
+#define XR21V141X_UART_MANAGER_RX_FIFO_RESET 0x18
+#define XR21V141X_UART_MANAGER_TX_FIFO_RESET 0x1c
+
+#define UART_ENABLE_TX 0x1
+#define UART_ENABLE_RX 0x2
+
+#define UART_MODE_RI BIT(0)
+#define UART_MODE_CD BIT(1)
+#define UART_MODE_DSR BIT(2)
+#define UART_MODE_DTR BIT(3)
+#define UART_MODE_CTS BIT(4)
+#define UART_MODE_RTS BIT(5)
+
+#define UART_BREAK_ON 0xff
+#define UART_BREAK_OFF 0
+
+#define UART_DATA_MASK GENMASK(3, 0)
+#define UART_DATA_7 0x7
+#define UART_DATA_8 0x8
+
+#define UART_PARITY_MASK GENMASK(6, 4)
+#define UART_PARITY_SHIFT 0x4
+#define UART_PARITY_NONE 0x0
+#define UART_PARITY_ODD 0x1
+#define UART_PARITY_EVEN 0x2
+#define UART_PARITY_MARK 0x3
+#define UART_PARITY_SPACE 0x4
+
+#define UART_STOP_MASK BIT(7)
+#define UART_STOP_SHIFT 0x7
+#define UART_STOP_1 0x0
+#define UART_STOP_2 0x1
+
+#define UART_FLOW_MODE_NONE 0x0
+#define UART_FLOW_MODE_HW 0x1
+#define UART_FLOW_MODE_SW 0x2
+
+#define UART_MODE_GPIO_MASK GENMASK(2, 0)
+#define UART_MODE_RTS_CTS 0x1
+#define UART_MODE_DTR_DSR 0x2
+#define UART_MODE_RS485 0x3
+#define UART_MODE_RS485_ADDR 0x4
+
+static const struct xr_uart_regs xr21v141x_regs = {
+ .enable = 0x03,
+ .format = 0x0b,
+ .flow_ctrl = 0x0c,
+ .xon_char = 0x10,
+ .xoff_char = 0x11,
+ .loopback = 0x12,
+ .tx_break = 0x14,
+ .rs485_delay = 0x15,
+ .gpio_mode = 0x1a,
+ .gpio_dir = 0x1b,
+ .gpio_int_mask = 0x1c,
+ .gpio_set = 0x1d,
+ .gpio_clr = 0x1e,
+ .gpio_status = 0x1f,
+};
+
+static int xr_set_reg(struct usb_serial_port *port, u8 block, u8 reg,
+ u8 val)
+{
+ struct usb_serial *serial = port->serial;
+ int ret;
+
+ ret = usb_control_msg(serial->dev,
+ usb_sndctrlpipe(serial->dev, 0),
+ XR_SET_XR21V141X,
+ USB_DIR_OUT | USB_TYPE_VENDOR, val,
+ reg | (block << 8), NULL, 0,
+ USB_CTRL_SET_TIMEOUT);
+ if (ret < 0) {
+ dev_err(&port->dev, "Failed to set reg 0x%02x: %d\n", reg, ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int xr_get_reg(struct usb_serial_port *port, u8 block, u8 reg,
+ u8 *val)
+{
+ struct usb_serial *serial = port->serial;
+ u8 *dmabuf;
+ int ret;
+
+ dmabuf = kmalloc(1, GFP_KERNEL);
+ if (!dmabuf)
+ return -ENOMEM;
+
+ ret = usb_control_msg(serial->dev,
+ usb_rcvctrlpipe(serial->dev, 0),
+ XR_GET_XR21V141X,
+ USB_DIR_IN | USB_TYPE_VENDOR, 0,
+ reg | (block << 8), dmabuf, 1,
+ USB_CTRL_GET_TIMEOUT);
+ if (ret == 1) {
+ *val = *dmabuf;
+ ret = 0;
+ } else {
+ dev_err(&port->dev, "Failed to get reg 0x%02x: %d\n", reg, ret);
+ if (ret >= 0)
+ ret = -EIO;
+ }
+
+ kfree(dmabuf);
+
+ return ret;
+}
+
+/* Tx and Rx clock mask values obtained from section 3.3.4 of datasheet */
+static const struct xr_txrx_clk_mask xr21v141x_txrx_clk_masks[] = {
+ { 0x000, 0x000, 0x000 },
+ { 0x000, 0x000, 0x000 },
+ { 0x100, 0x000, 0x100 },
+ { 0x020, 0x400, 0x020 },
+ { 0x010, 0x100, 0x010 },
+ { 0x208, 0x040, 0x208 },
+ { 0x104, 0x820, 0x108 },
+ { 0x844, 0x210, 0x884 },
+ { 0x444, 0x110, 0x444 },
+ { 0x122, 0x888, 0x224 },
+ { 0x912, 0x448, 0x924 },
+ { 0x492, 0x248, 0x492 },
+ { 0x252, 0x928, 0x292 },
+ { 0x94a, 0x4a4, 0xa52 },
+ { 0x52a, 0xaa4, 0x54a },
+ { 0xaaa, 0x954, 0x4aa },
+ { 0xaaa, 0x554, 0xaaa },
+ { 0x555, 0xad4, 0x5aa },
+ { 0xb55, 0xab4, 0x55a },
+ { 0x6b5, 0x5ac, 0xb56 },
+ { 0x5b5, 0xd6c, 0x6d6 },
+ { 0xb6d, 0xb6a, 0xdb6 },
+ { 0x76d, 0x6da, 0xbb6 },
+ { 0xedd, 0xdda, 0x76e },
+ { 0xddd, 0xbba, 0xeee },
+ { 0x7bb, 0xf7a, 0xdde },
+ { 0xf7b, 0xef6, 0x7de },
+ { 0xdf7, 0xbf6, 0xf7e },
+ { 0x7f7, 0xfee, 0xefe },
+ { 0xfdf, 0xfbe, 0x7fe },
+ { 0xf7f, 0xefe, 0xffe },
+ { 0xfff, 0xffe, 0xffd },
+};
+
+static int xr_set_baudrate(struct tty_struct *tty,
+ struct usb_serial_port *port)
+{
+ u32 divisor, baud, idx;
+ u16 tx_mask, rx_mask;
+ int ret;
+
+ baud = clamp(tty->termios.c_ospeed, XR21V141X_MIN_SPEED,
+ XR21V141X_MAX_SPEED);
+ divisor = XR_INT_OSC_HZ / baud;
+ idx = (32 * divisor) & 0x1f;
+ tx_mask = xr21v141x_txrx_clk_masks[idx].tx;
+
+ if (divisor & 1)
+ rx_mask = xr21v141x_txrx_clk_masks[idx].rx1;
+ else
+ rx_mask = xr21v141x_txrx_clk_masks[idx].rx0;
+
+ dev_dbg(&port->dev, "Setting baud rate: %u\n", baud);
+ /*
+ * XR21V141X uses fractional baud rate generator with 48MHz internal
+ * oscillator and 19-bit programmable divisor. So theoretically it can
+ * generate most commonly used baud rates with high accuracy.
+ */
+ ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
+ XR21V141X_CLOCK_DIVISOR_0, (divisor & 0xff));
+ if (ret)
+ return ret;
+
+ ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
+ XR21V141X_CLOCK_DIVISOR_1, ((divisor >> 8) & 0xff));
+ if (ret)
+ return ret;
+
+ ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
+ XR21V141X_CLOCK_DIVISOR_2, ((divisor >> 16) & 0xff));
+ if (ret)
+ return ret;
+
+ ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
+ XR21V141X_TX_CLOCK_MASK_0, (tx_mask & 0xff));
+ if (ret)
+ return ret;
+
+ ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
+ XR21V141X_TX_CLOCK_MASK_1, ((tx_mask >> 8) & 0xff));
+ if (ret)
+ return ret;
+
+ ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
+ XR21V141X_RX_CLOCK_MASK_0, (rx_mask & 0xff));
+ if (ret)
+ return ret;
+
+ ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
+ XR21V141X_RX_CLOCK_MASK_1, ((rx_mask >> 8) & 0xff));
+
+ tty_encode_baud_rate(tty, baud, baud);
+
+ return ret;
+}
+
+/*
+ * According to datasheet, below is the recommended sequence for enabling UART
+ * module in XR21V141X:
+ *
+ * Enable Tx FIFO
+ * Enable Tx and Rx
+ * Enable Rx FIFO
+ */
+static int xr_uart_enable(struct usb_serial_port *port)
+{
+ struct xr_port_private *port_priv = usb_get_serial_port_data(port);
+ int ret;
+
+ ret = xr_set_reg(port, XR21V141X_UART_MANAGER_REG_BLOCK,
+ XR21V141X_UART_MANAGER_FIFO_ENABLE_REG,
+ XR21V141X_UART_MANAGER_ENABLE_TX_FIFO);
+ if (ret)
+ return ret;
+
+ ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
+ port_priv->regs->enable,
+ UART_ENABLE_TX | UART_ENABLE_RX);
+ if (ret)
+ return ret;
+
+ ret = xr_set_reg(port, XR21V141X_UART_MANAGER_REG_BLOCK,
+ XR21V141X_UART_MANAGER_FIFO_ENABLE_REG,
+ XR21V141X_UART_MANAGER_ENABLE_TX_FIFO |
+ XR21V141X_UART_MANAGER_ENABLE_RX_FIFO);
+
+ return ret;
+}
+
+static int xr_uart_disable(struct usb_serial_port *port)
+{
+ struct xr_port_private *port_priv = usb_get_serial_port_data(port);
+ int ret;
+
+ ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
+ port_priv->regs->enable, 0);
+ if (ret)
+ return ret;
+
+ ret = xr_set_reg(port, XR21V141X_UART_MANAGER_REG_BLOCK,
+ XR21V141X_UART_MANAGER_FIFO_ENABLE_REG, 0);
+
+ return ret;
+}
+
+static int xr_open(struct tty_struct *tty, struct usb_serial_port *port)
+{
+ int ret;
+ struct device *dev = &port->dev;
+ struct xr_port_private *port_priv = usb_get_serial_port_data(port);
+
+ ret = xr_uart_enable(port);
+ if (ret) {
+ dev_err(&port->dev, "Failed to enable UART\n");
+ return ret;
+ }
+
+ /* Setup termios */
+ if (tty)
+ xr_set_termios(tty, port, NULL);
+
+ ret = usb_serial_generic_open(tty, port);
+ if (ret) {
+ dev_err(dev, "usb_serial_generic_open failed: %d\n", ret);
+ xr_uart_disable(port);
+ return ret;
+ }
+
+ port_priv->port_open = true;
+
+ return ret;
+}
+
+static void xr_close(struct usb_serial_port *port)
+{
+ struct xr_port_private *port_priv = usb_get_serial_port_data(port);
+
+ usb_serial_generic_close(port);
+ port_priv->port_open = false;
+ xr_uart_disable(port);
+}
+
+static void xr_set_flow_mode(struct tty_struct *tty,
+ struct usb_serial_port *port)
+{
+ struct xr_port_private *port_priv = usb_get_serial_port_data(port);
+ unsigned int cflag = tty->termios.c_cflag;
+ int ret;
+ u8 flow, gpio_mode;
+
+ ret = xr_get_reg(port, XR21V141X_UART_REG_BLOCK,
+ port_priv->regs->gpio_mode, &gpio_mode);
+ if (ret)
+ return;
+
+ /*
+ * RTS/CTS is the default flow control mode, so set GPIO mode
+ * for controlling the pins manually by default.
+ */
+ gpio_mode &= ~UART_MODE_GPIO_MASK;
+ if (cflag & CRTSCTS) {
+ dev_dbg(&port->dev, "Enabling hardware flow ctrl\n");
+ flow = UART_FLOW_MODE_HW;
+ gpio_mode |= UART_MODE_RTS_CTS;
+ } else if (I_IXOFF(tty)) {
+ u8 start_char = START_CHAR(tty);
+ u8 stop_char = STOP_CHAR(tty);
+
+ dev_dbg(&port->dev, "Enabling sw flow ctrl\n");
+ flow = UART_FLOW_MODE_SW;
+
+ xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
+ port_priv->regs->xon_char, start_char);
+ xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
+ port_priv->regs->xoff_char, stop_char);
+ } else {
+ dev_dbg(&port->dev, "No flow ctrl\n");
+ flow = UART_FLOW_MODE_NONE;
+ }
+
+ /*
+ * As per the datasheet, UART needs to be disabled while writing to
+ * FLOW_CONTROL register.
+ */
+ xr_uart_disable(port);
+ xr_set_reg(port, XR21V141X_UART_REG_BLOCK, port_priv->regs->flow_ctrl,
+ flow);
+ xr_uart_enable(port);
+
+ xr_set_reg(port, XR21V141X_UART_REG_BLOCK, port_priv->regs->gpio_mode,
+ gpio_mode);
+}
+
+static void xr_set_termios(struct tty_struct *tty,
+ struct usb_serial_port *port,
+ struct ktermios *old_termios)
+{
+ struct xr_port_private *port_priv = usb_get_serial_port_data(port);
+ struct ktermios *termios = &tty->termios;
+ int ret;
+ u8 bits = 0;
+
+ if (old_termios &&
+ tty->termios.c_ospeed != old_termios->c_ospeed)
+ xr_set_baudrate(tty, port);
+
+ switch (C_CSIZE(tty)) {
+ case CS5:
+ /* fall through */
+ case CS6:
+ dev_warn(&port->dev, "requested CSIZE setting not supported\n");
+
+ /* CS5 and CS6 are not supported, so just restore old setting */
+ termios->c_cflag &= ~CSIZE;
+ if (old_termios)
+ termios->c_cflag |= old_termios->c_cflag & CSIZE;
+ break;
+ case CS7:
+ bits |= UART_DATA_7;
+ break;
+ case CS8:
+ /* fall through */
+ default:
+ bits |= UART_DATA_8;
+ break;
+ }
+
+ if (C_PARENB(tty)) {
+ if (C_CMSPAR(tty)) {
+ if (C_PARODD(tty)) {
+ bits |= (UART_PARITY_MARK <<
+ UART_PARITY_SHIFT);
+ } else {
+ bits |= (UART_PARITY_SPACE <<
+ UART_PARITY_SHIFT);
+ }
+ } else {
+ if (C_PARODD(tty)) {
+ bits |= (UART_PARITY_ODD <<
+ UART_PARITY_SHIFT);
+ } else {
+ bits |= (UART_PARITY_EVEN <<
+ UART_PARITY_SHIFT);
+ }
+ }
+ }
+
+ if (C_CSTOPB(tty))
+ bits |= (UART_STOP_2 << UART_STOP_SHIFT);
+ else
+ bits |= (UART_STOP_1 << UART_STOP_SHIFT);
+
+ ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
+ port_priv->regs->format, bits);
+ if (ret)
+ return;
+
+ xr_set_flow_mode(tty, port);
+}
+
+static int xr_tiocmset_port(struct usb_serial_port *port,
+ unsigned int set, unsigned int clear)
+{
+ struct xr_port_private *port_priv = usb_get_serial_port_data(port);
+ int ret = 0;
+ u8 gpio_set = 0;
+ u8 gpio_clr = 0;
+
+ /* Modem control pins are active low, so set & clr are swapped */
+ if (set & TIOCM_RTS)
+ gpio_clr |= UART_MODE_RTS;
+ if (set & TIOCM_DTR)
+ gpio_clr |= UART_MODE_DTR;
+ if (clear & TIOCM_RTS)
+ gpio_set |= UART_MODE_RTS;
+ if (clear & TIOCM_DTR)
+ gpio_set |= UART_MODE_DTR;
+
+ /* Writing '0' to gpio_{set/clr} bits has no effect, so no need to do */
+ if (gpio_clr) {
+ ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
+ port_priv->regs->gpio_clr, gpio_clr);
+ }
+
+ if (gpio_set) {
+ ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
+ port_priv->regs->gpio_set, gpio_set);
+ }
+
+ return ret;
+}
+
+static int xr_tiocmset(struct tty_struct *tty,
+ unsigned int set, unsigned int clear)
+{
+ struct usb_serial_port *port = tty->driver_data;
+
+ return xr_tiocmset_port(port, set, clear);
+}
+
+static int xr_attach(struct usb_serial *serial)
+{
+ /* Do not register tty device for the control interface */
+ if (serial->interface->cur_altsetting->desc.bInterfaceNumber == 0)
+ return 1;
+
+ return 0;
+}
+
+static void xr_dtr_rts(struct usb_serial_port *port, int on)
+{
+ if (on)
+ xr_tiocmset_port(port, TIOCM_DTR | TIOCM_RTS, 0);
+ else
+ xr_tiocmset_port(port, 0, TIOCM_DTR | TIOCM_RTS);
+}
+
+static int xr_tiocmget(struct tty_struct *tty)
+{
+ struct usb_serial_port *port = tty->driver_data;
+ struct xr_port_private *port_priv = usb_get_serial_port_data(port);
+ int ret;
+ u8 status;
+
+ ret = xr_get_reg(port, XR21V141X_UART_REG_BLOCK,
+ port_priv->regs->gpio_status, &status);
+ if (ret)
+ return ret;
+
+ /*
+ * Modem control pins are active low, so reading '0' means it is active
+ * and '1' means not active.
+ */
+ ret = ((status & UART_MODE_DTR) ? 0 : TIOCM_DTR) |
+ ((status & UART_MODE_RTS) ? 0 : TIOCM_RTS) |
+ ((status & UART_MODE_CTS) ? 0 : TIOCM_CTS) |
+ ((status & UART_MODE_DSR) ? 0 : TIOCM_DSR) |
+ ((status & UART_MODE_RI) ? 0 : TIOCM_RI) |
+ ((status & UART_MODE_CD) ? 0 : TIOCM_CD);
+
+ return ret;
+}
+
+static void xr_break_ctl(struct tty_struct *tty, int break_state)
+{
+ struct usb_serial_port *port = tty->driver_data;
+ struct xr_port_private *port_priv = usb_get_serial_port_data(port);
+ u8 state;
+
+ if (break_state == 0)
+ state = UART_BREAK_OFF;
+ else
+ state = UART_BREAK_ON;
+
+ dev_dbg(&port->dev, "Turning break %s\n",
+ state == UART_BREAK_OFF ? "off" : "on");
+ xr_set_reg(port, XR21V141X_UART_REG_BLOCK, port_priv->regs->tx_break,
+ state);
+}
+
+static int xr_port_probe(struct usb_serial_port *port)
+{
+ struct xr_port_private *port_priv;
+
+ port_priv = kzalloc(sizeof(*port_priv), GFP_KERNEL);
+ if (!port_priv)
+ return -ENOMEM;
+
+ /* XR21V141X specific settings */
+ port_priv->regs = &xr21v141x_regs;
+
+ usb_set_serial_port_data(port, port_priv);
+
+ return 0;
+}
+
+static int xr_port_remove(struct usb_serial_port *port)
+{
+ struct xr_port_private *port_priv = usb_get_serial_port_data(port);
+
+ kfree(port_priv);
+
+ return 0;
+}
+
+static const struct usb_device_id id_table[] = {
+ { USB_DEVICE(0x04e2, 0x1410) }, /* XR21V141X */
+ { }
+};
+MODULE_DEVICE_TABLE(usb, id_table);
+
+static struct usb_serial_driver xr_device = {
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = "xr_serial",
+ },
+ .id_table = id_table,
+ .num_ports = 1,
+ .open = xr_open,
+ .close = xr_close,
+ .break_ctl = xr_break_ctl,
+ .set_termios = xr_set_termios,
+ .tiocmget = xr_tiocmget,
+ .tiocmset = xr_tiocmset,
+ .attach = xr_attach,
+ .port_probe = xr_port_probe,
+ .port_remove = xr_port_remove,
+ .dtr_rts = xr_dtr_rts
+};
+
+static struct usb_serial_driver * const serial_drivers[] = {
+ &xr_device, NULL
+};
+
+module_usb_serial_driver(serial_drivers, id_table);
+
+MODULE_AUTHOR("Manivannan Sadhasivam <[email protected]>");
+MODULE_DESCRIPTION("MaxLinear/Exar USB to Serial driver");
+MODULE_LICENSE("GPL");
--
2.17.1
Add gpiochip support for Maxlinear/Exar USB to serial converter
for controlling the available gpios.
Inspired from cp210x usb to serial converter driver.
Cc: Linus Walleij <[email protected]>
Cc: [email protected]
Reviewed-by: Linus Walleij <[email protected]>
Signed-off-by: Manivannan Sadhasivam <[email protected]>
---
drivers/usb/serial/xr_serial.c | 209 ++++++++++++++++++++++++++++++++-
1 file changed, 208 insertions(+), 1 deletion(-)
diff --git a/drivers/usb/serial/xr_serial.c b/drivers/usb/serial/xr_serial.c
index bb7df79cc129..2240fbc9ea7f 100644
--- a/drivers/usb/serial/xr_serial.c
+++ b/drivers/usb/serial/xr_serial.c
@@ -10,6 +10,7 @@
* Copyright (c) 2020 Manivannan Sadhasivam <[email protected]>
*/
+#include <linux/gpio/driver.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/slab.h>
@@ -17,6 +18,18 @@
#include <linux/usb.h>
#include <linux/usb/serial.h>
+#ifdef CONFIG_GPIOLIB
+enum gpio_pins {
+ GPIO_RI = 0,
+ GPIO_CD,
+ GPIO_DSR,
+ GPIO_DTR,
+ GPIO_CTS,
+ GPIO_RTS,
+ GPIO_MAX,
+};
+#endif
+
static void xr_set_termios(struct tty_struct *tty,
struct usb_serial_port *port,
struct ktermios *old_termios);
@@ -39,6 +52,11 @@ struct xr_uart_regs {
};
struct xr_port_private {
+#ifdef CONFIG_GPIOLIB
+ struct gpio_chip gc;
+ bool gpio_registered;
+ enum gpio_pins pin_status[GPIO_MAX];
+#endif
const struct xr_uart_regs *regs;
bool port_open;
};
@@ -390,6 +408,13 @@ static void xr_set_flow_mode(struct tty_struct *tty,
*/
gpio_mode &= ~UART_MODE_GPIO_MASK;
if (cflag & CRTSCTS) {
+#ifdef CONFIG_GPIOLIB
+ /* Check if the CTS/RTS pins are occupied */
+ if (port_priv->pin_status[GPIO_RTS] ||
+ port_priv->pin_status[GPIO_CTS])
+ return;
+#endif
+
dev_dbg(&port->dev, "Enabling hardware flow ctrl\n");
flow = UART_FLOW_MODE_HW;
gpio_mode |= UART_MODE_RTS_CTS;
@@ -497,6 +522,17 @@ static int xr_tiocmset_port(struct usb_serial_port *port,
u8 gpio_set = 0;
u8 gpio_clr = 0;
+#ifdef CONFIG_GPIOLIB
+ /* Check if the RTS/DTR pins are occupied */
+ if (set & TIOCM_RTS || clear & TIOCM_RTS)
+ if (port_priv->pin_status[GPIO_RTS])
+ return -EBUSY;
+
+ if (set & TIOCM_DTR || clear & TIOCM_DTR)
+ if (port_priv->pin_status[GPIO_DTR])
+ return -EBUSY;
+#endif
+
/* Modem control pins are active low, so set & clr are swapped */
if (set & TIOCM_RTS)
gpio_clr |= UART_MODE_RTS;
@@ -589,9 +625,175 @@ static void xr_break_ctl(struct tty_struct *tty, int break_state)
state);
}
+#ifdef CONFIG_GPIOLIB
+
+static int xr_gpio_request(struct gpio_chip *gc, unsigned int offset)
+{
+ struct usb_serial_port *port = gpiochip_get_data(gc);
+ struct xr_port_private *port_priv = usb_get_serial_port_data(port);
+
+ /*
+ * Do not proceed if the port is open. This is done to avoid changing
+ * the GPIO configuration used by the serial driver.
+ */
+ if (port_priv->port_open)
+ return -EBUSY;
+
+ /* Mark the GPIO pin as busy */
+ port_priv->pin_status[offset] = true;
+
+ return 0;
+}
+
+static void xr_gpio_free(struct gpio_chip *gc, unsigned int offset)
+{
+ struct usb_serial_port *port = gpiochip_get_data(gc);
+ struct xr_port_private *port_priv = usb_get_serial_port_data(port);
+
+ /* Mark the GPIO pin as free */
+ port_priv->pin_status[offset] = false;
+}
+
+static int xr_gpio_get(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct usb_serial_port *port = gpiochip_get_data(gc);
+ struct xr_port_private *port_priv = usb_get_serial_port_data(port);
+ int ret;
+ u8 gpio_status;
+
+ ret = xr_get_reg(port, XR21V141X_UART_REG_BLOCK,
+ port_priv->regs->gpio_status, &gpio_status);
+ if (ret)
+ return ret;
+
+ return !!(gpio_status & BIT(gpio));
+}
+
+static void xr_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+ struct usb_serial_port *port = gpiochip_get_data(gc);
+ struct xr_port_private *port_priv = usb_get_serial_port_data(port);
+
+ if (val)
+ xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
+ port_priv->regs->gpio_set, BIT(gpio));
+ else
+ xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
+ port_priv->regs->gpio_clr, BIT(gpio));
+}
+
+static int xr_gpio_direction_get(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct usb_serial_port *port = gpiochip_get_data(gc);
+ struct xr_port_private *port_priv = usb_get_serial_port_data(port);
+ int ret;
+ u8 gpio_dir;
+
+ ret = xr_get_reg(port, XR21V141X_UART_REG_BLOCK,
+ port_priv->regs->gpio_dir, &gpio_dir);
+ if (ret)
+ return ret;
+
+ /* Logic 0 = input and Logic 1 = output */
+ return !(gpio_dir & BIT(gpio));
+}
+
+static int xr_gpio_direction_input(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct usb_serial_port *port = gpiochip_get_data(gc);
+ struct xr_port_private *port_priv = usb_get_serial_port_data(port);
+ int ret;
+ u8 gpio_dir;
+
+ ret = xr_get_reg(port, XR21V141X_UART_REG_BLOCK,
+ port_priv->regs->gpio_dir, &gpio_dir);
+ if (ret)
+ return ret;
+
+ gpio_dir &= ~BIT(gpio);
+
+ return xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
+ port_priv->regs->gpio_dir, gpio_dir);
+}
+
+static int xr_gpio_direction_output(struct gpio_chip *gc, unsigned int gpio,
+ int val)
+{
+ struct usb_serial_port *port = gpiochip_get_data(gc);
+ struct xr_port_private *port_priv = usb_get_serial_port_data(port);
+ int ret;
+ u8 gpio_dir;
+
+ xr_gpio_set(gc, gpio, val);
+
+ ret = xr_get_reg(port, XR21V141X_UART_REG_BLOCK,
+ port_priv->regs->gpio_dir, &gpio_dir);
+ if (ret)
+ return ret;
+
+ gpio_dir |= BIT(gpio);
+
+ ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
+ port_priv->regs->gpio_dir, gpio_dir);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int xr_gpio_init(struct usb_serial_port *port)
+{
+ struct xr_port_private *port_priv = usb_get_serial_port_data(port);
+ int ret = 0;
+
+ port_priv->gc.ngpio = 6;
+ port_priv->gc.label = "xr_gpios";
+ port_priv->gc.request = xr_gpio_request;
+ port_priv->gc.free = xr_gpio_free;
+ port_priv->gc.get_direction = xr_gpio_direction_get;
+ port_priv->gc.direction_input = xr_gpio_direction_input;
+ port_priv->gc.direction_output = xr_gpio_direction_output;
+ port_priv->gc.get = xr_gpio_get;
+ port_priv->gc.set = xr_gpio_set;
+ port_priv->gc.owner = THIS_MODULE;
+ port_priv->gc.parent = &port->dev;
+ port_priv->gc.base = -1;
+ port_priv->gc.can_sleep = true;
+
+ ret = gpiochip_add_data(&port_priv->gc, port);
+ if (!ret)
+ port_priv->gpio_registered = true;
+
+ return ret;
+}
+
+static void xr_gpio_remove(struct usb_serial_port *port)
+{
+ struct xr_port_private *port_priv = usb_get_serial_port_data(port);
+
+ if (port_priv->gpio_registered) {
+ gpiochip_remove(&port_priv->gc);
+ port_priv->gpio_registered = false;
+ }
+}
+
+#else
+
+static int xr_gpio_init(struct usb_serial_port *port)
+{
+ return 0;
+}
+
+static void xr_gpio_remove(struct usb_serial_port *port)
+{
+}
+
+#endif
+
static int xr_port_probe(struct usb_serial_port *port)
{
struct xr_port_private *port_priv;
+ int ret;
port_priv = kzalloc(sizeof(*port_priv), GFP_KERNEL);
if (!port_priv)
@@ -602,13 +804,18 @@ static int xr_port_probe(struct usb_serial_port *port)
usb_set_serial_port_data(port, port_priv);
- return 0;
+ ret = xr_gpio_init(port);
+ if (ret)
+ kfree(port_priv);
+
+ return ret;
}
static int xr_port_remove(struct usb_serial_port *port)
{
struct xr_port_private *port_priv = usb_get_serial_port_data(port);
+ xr_gpio_remove(port);
kfree(port_priv);
return 0;
--
2.17.1
From: Mauro Carvalho Chehab <[email protected]>
The RTS/CTS line discipline for this device doesn't follow
the standard. So, in order to properly support TX, a separate
driver is needed.
Ensure that cdc_acm will ignore it during probe time, if the
Kernel is built with support for it.
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Manivannan Sadhasivam <[email protected]>
---
drivers/usb/class/cdc-acm.c | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c
index 84d6f7df09a4..30e20d06d044 100644
--- a/drivers/usb/class/cdc-acm.c
+++ b/drivers/usb/class/cdc-acm.c
@@ -1864,6 +1864,12 @@ static const struct usb_device_id acm_ids[] = {
},
#endif
+#if IS_ENABLED(CONFIG_USB_SERIAL_XR)
+ { USB_DEVICE(0x04e2, 0x1410), /* Ignore XR21V141X USB to Serial converter */
+ .driver_info = IGNORE_DEVICE,
+ },
+#endif
+
/*Samsung phone in firmware update mode */
{ USB_DEVICE(0x04e8, 0x685d),
.driver_info = IGNORE_DEVICE,
--
2.17.1
On Sun, Jun 07, 2020 at 09:38:06PM +0530, Manivannan Sadhasivam wrote:
> Hello,
>
> This series adds support for MaxLinear/Exar USB to serial converters.
> This driver only supports XR21V141X series but it can easily be extended
> to other series in future.
>
> This driver is inspired from the initial one submitted by Patong Yang:
>
> https://patchwork.kernel.org/patch/10543261/
>
> While the initial driver was a custom tty USB driver exposing whole
> new serial interface ttyXRUSBn, this version is completely based on USB
> serial core thus exposing the interfaces as ttyUSBn. This will avoid
> the overhead of exposing a new USB serial interface which the userspace
> tools are unaware of.
>
> This series has been tested with Hikey970 board hosting XR21V141X chip.
>
Gentle ping on this series!
Thanks,
Mani
> Thanks,
> Mani
>
> Changes in v4:
>
> * Multiple improvements based on Johan's review. Noticeable ones are:
> - Now the driver claims both control and data interfaces but only registers
> tty device for data interface.
> - GPIO pin status is now shared between the console and gpiolib
> implementations. This is done to avoid changing the lines spuriously.
> - A separate port_open flag is added to reject GPIO requests while the tty
> port is open.
> - Removed padding PID to gpio device.
> * Added Greg and Mauro's review and tested tags.
> * Included a patch from Mauro to avoid the CDC-ACM driver to claim this device
> when this driver is built.
>
> Changes in v3:
>
> * Dropped the check for PID and also the reg_width property.
>
> Changes in v2:
>
> * Dropped the code related to handling variable register size. It's all u8 now.
> * Dropped the header file and moved the contents to driver itself.
> * Added Linus's reviewed-by tag for gpiochip patch.
> * Added PID to gpiochip label
> * Dropped gpiochip for interface 0
>
> Manivannan Sadhasivam (2):
> usb: serial: Add MaxLinear/Exar USB to Serial driver
> usb: serial: xr_serial: Add gpiochip support
>
> Mauro Carvalho Chehab (1):
> usb: cdc-acm: Ignore Exar XR21V141X when serial driver is built
>
> drivers/usb/class/cdc-acm.c | 6 +
> drivers/usb/serial/Kconfig | 9 +
> drivers/usb/serial/Makefile | 1 +
> drivers/usb/serial/xr_serial.c | 857 +++++++++++++++++++++++++++++++++
> 4 files changed, 873 insertions(+)
> create mode 100644 drivers/usb/serial/xr_serial.c
>
> --
> 2.17.1
>
On Fri, Jun 26, 2020 at 08:01:36PM +0530, Manivannan Sadhasivam wrote:
> On Sun, Jun 07, 2020 at 09:38:06PM +0530, Manivannan Sadhasivam wrote:
> > Hello,
> >
> > This series adds support for MaxLinear/Exar USB to serial converters.
> > This driver only supports XR21V141X series but it can easily be extended
> > to other series in future.
> >
> > This driver is inspired from the initial one submitted by Patong Yang:
> >
> > https://patchwork.kernel.org/patch/10543261/
> >
> > While the initial driver was a custom tty USB driver exposing whole
> > new serial interface ttyXRUSBn, this version is completely based on USB
> > serial core thus exposing the interfaces as ttyUSBn. This will avoid
> > the overhead of exposing a new USB serial interface which the userspace
> > tools are unaware of.
> >
> > This series has been tested with Hikey970 board hosting XR21V141X chip.
> >
>
> Gentle ping on this series!
You sending this in reply to your superseded v4. Please make sure to
always increment the revision number when updating a series, including
when changing authorship.
Johan