Hello,
This patchset adds additional health properties to the power_supply header.
These additional properties are taken from the JEITA specification. This
patchset also introduces the bq2515x family of charging ICs.
Dan Murphy (2):
power_supply: Add additional health properties to the header
dt-bindings: power: Convert battery.txt to battery.yaml
Ricardo Rivera-Matos (2):
dt-bindings: power: Add the bindings for the bq2515x family of
chargers.
power: supply: bq25150 introduce the bq25150
Documentation/ABI/testing/sysfs-class-power | 3 +-
.../bindings/power/supply/battery.txt | 86 +-
.../bindings/power/supply/battery.yaml | 139 ++
.../bindings/power/supply/bq2515x.yaml | 93 ++
drivers/power/supply/Kconfig | 13 +
drivers/power/supply/Makefile | 1 +
drivers/power/supply/bq2515x_charger.c | 1169 +++++++++++++++++
drivers/power/supply/power_supply_sysfs.c | 3 +
include/linux/power_supply.h | 3 +
9 files changed, 1424 insertions(+), 86 deletions(-)
create mode 100644 Documentation/devicetree/bindings/power/supply/battery.yaml
create mode 100644 Documentation/devicetree/bindings/power/supply/bq2515x.yaml
create mode 100644 drivers/power/supply/bq2515x_charger.c
--
2.27.0
From: Dan Murphy <[email protected]>
Convert the battery.txt file to yaml and fix up the examples.
Signed-off-by: Dan Murphy <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
---
.../bindings/power/supply/battery.txt | 86 +----------
.../bindings/power/supply/battery.yaml | 139 ++++++++++++++++++
2 files changed, 140 insertions(+), 85 deletions(-)
create mode 100644 Documentation/devicetree/bindings/power/supply/battery.yaml
diff --git a/Documentation/devicetree/bindings/power/supply/battery.txt b/Documentation/devicetree/bindings/power/supply/battery.txt
index 5e29595edd74..a9f80cc49068 100644
--- a/Documentation/devicetree/bindings/power/supply/battery.txt
+++ b/Documentation/devicetree/bindings/power/supply/battery.txt
@@ -1,87 +1,3 @@
-Battery Characteristics
-
-The devicetree battery node provides static battery characteristics.
-In smart batteries, these are typically stored in non-volatile memory
-on a fuel gauge chip. The battery node should be used where there is
-no appropriate non-volatile memory, or it is unprogrammed/incorrect.
-
-Upstream dts files should not include battery nodes, unless the battery
-represented cannot easily be replaced in the system by one of a
-different type. This prevents unpredictable, potentially harmful,
-behavior should a replacement that changes the battery type occur
-without a corresponding update to the dtb.
+The contents of this file has been moved to battery.yaml
Please note that not all charger drivers respect all of the properties.
-
-Required Properties:
- - compatible: Must be "simple-battery"
-
-Optional Properties:
- - over-voltage-threshold-microvolt: battery over-voltage limit
- - re-charge-voltage-microvolt: limit to automatically start charging again
- - voltage-min-design-microvolt: drained battery voltage
- - voltage-max-design-microvolt: fully charged battery voltage
- - energy-full-design-microwatt-hours: battery design energy
- - charge-full-design-microamp-hours: battery design capacity
- - trickle-charge-current-microamp: current for trickle-charge phase
- - precharge-current-microamp: current for pre-charge phase
- - precharge-upper-limit-microvolt: limit when to change to constant charging
- - charge-term-current-microamp: current for charge termination phase
- - constant-charge-current-max-microamp: maximum constant input current
- - constant-charge-voltage-max-microvolt: maximum constant input voltage
- - factory-internal-resistance-micro-ohms: battery factory internal resistance
- - ocv-capacity-table-0: An array providing the open circuit voltage (OCV)
- of the battery and corresponding battery capacity percent, which is used
- to look up battery capacity according to current OCV value. And the open
- circuit voltage unit is microvolt.
- - ocv-capacity-table-1: Same as ocv-capacity-table-0
- ......
- - ocv-capacity-table-n: Same as ocv-capacity-table-0
- - ocv-capacity-celsius: An array containing the temperature in degree Celsius,
- for each of the battery capacity lookup table. The first temperature value
- specifies the OCV table 0, and the second temperature value specifies the
- OCV table 1, and so on.
- - resistance-temp-table: An array providing the temperature in degree Celsius
- and corresponding battery internal resistance percent, which is used to look
- up the resistance percent according to current temperature to get a accurate
- batterty internal resistance in different temperatures.
-
-Battery properties are named, where possible, for the corresponding
-elements in enum power_supply_property, defined in
-https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/include/linux/power_supply.h
-
-Batteries must be referenced by chargers and/or fuel-gauges
-using a phandle. The phandle's property should be named
-"monitored-battery".
-
-Example:
-
- bat: battery {
- compatible = "simple-battery";
- voltage-min-design-microvolt = <3200000>;
- voltage-max-design-microvolt = <4200000>;
- energy-full-design-microwatt-hours = <5290000>;
- charge-full-design-microamp-hours = <1430000>;
- precharge-current-microamp = <256000>;
- charge-term-current-microamp = <128000>;
- constant-charge-current-max-microamp = <900000>;
- constant-charge-voltage-max-microvolt = <4200000>;
- factory-internal-resistance-micro-ohms = <250000>;
- ocv-capacity-celsius = <(-10) 0 10>;
- ocv-capacity-table-0 = <4185000 100>, <4113000 95>, <4066000 90>, ...;
- ocv-capacity-table-1 = <4200000 100>, <4185000 95>, <4113000 90>, ...;
- ocv-capacity-table-2 = <4250000 100>, <4200000 95>, <4185000 90>, ...;
- resistance-temp-table = <20 100>, <10 90>, <0 80>, <(-10) 60>;
- };
-
- charger: charger@11 {
- ....
- monitored-battery = <&bat>;
- ...
- };
-
- fuel_gauge: fuel-gauge@22 {
- ....
- monitored-battery = <&bat>;
- ...
- };
diff --git a/Documentation/devicetree/bindings/power/supply/battery.yaml b/Documentation/devicetree/bindings/power/supply/battery.yaml
new file mode 100644
index 000000000000..2fa3be745d71
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/battery.yaml
@@ -0,0 +1,139 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/power/supply/battery.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Battery Characteristics
+
+maintainers:
+ - Sebastian Reichel <[email protected]>
+
+description: |
+ The devicetree battery node provides static battery characteristics.
+ In smart batteries, these are typically stored in non-volatile memory
+ on a fuel gauge chip. The battery node should be used where there is
+ no appropriate non-volatile memory, or it is unprogrammed/incorrect.
+
+ Upstream dts files should not include battery nodes, unless the battery
+ represented cannot easily be replaced in the system by one of a
+ different type. This prevents unpredictable, potentially harmful,
+ behavior should a replacement that changes the battery type occur
+ without a corresponding update to the dtb.
+
+ Battery properties are named, where possible, for the corresponding elements
+ in enum power_supply_property, defined in include/linux/power_supply.h
+
+ Batteries must be referenced by chargers and/or fuel-gauges using a phandle.
+ The phandle's property should be named "monitored-battery".
+
+properties:
+ compatible:
+ const: simple-battery
+
+ over-voltage-threshold-microvolt:
+ description: battery over-voltage limit
+
+ re-charge-voltage-microvolt:
+ description: limit to automatically start charging again
+
+ voltage-min-design-microvolt:
+ description: drained battery voltage
+
+ voltage-max-design-microvolt:
+ description: fully charged battery voltage
+
+ energy-full-design-microwatt-hours:
+ description: battery design energy
+
+ charge-full-design-microamp-hours:
+ description: battery design capacity
+
+ trickle-charge-current-microamp:
+ description: current for trickle-charge phase
+
+ precharge-current-microamp:
+ description: current for pre-charge phase
+
+ precharge-upper-limit-microvolt:
+ description: limit when to change to constant charging
+
+ charge-term-current-microamp:
+ description: current for charge termination phase
+
+ constant-charge-current-max-microamp:
+ description: maximum constant input current
+
+ constant-charge-voltage-max-microvolt:
+ description: maximum constant input voltage
+
+ factory-internal-resistance-micro-ohms:
+ description: battery factory internal resistance
+
+ resistance-temp-table:
+ description: |
+ An array providing the temperature in degree Celsius
+ and corresponding battery internal resistance percent, which is used to
+ look up the resistance percent according to current temperature to get an
+ accurate batterty internal resistance in different temperatures.
+
+ ocv-capacity-celsius:
+ description: |
+ An array containing the temperature in degree Celsius,
+ for each of the battery capacity lookup table.
+
+required:
+ - compatible
+
+patternProperties:
+ '^ocv-capacity-table-[0-100]$':
+ $ref: /schemas/types.yaml#/definitions/uint32-matrix
+ description: |
+ An array providing the open circuit voltage (OCV)
+ of the battery and corresponding battery capacity percent, which is used
+ to look up battery capacity according to current OCV value. And the open
+ circuit voltage unit is microvolt.
+ maxItems: 100
+ items:
+ items:
+ - description: open circuit voltage (OCV) in microvolts
+ - description: battery capacity percent
+ maximum: 100
+
+additionalProperties: false
+
+examples:
+ - |
+ power {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ battery: battery {
+ compatible = "simple-battery";
+ over-voltage-threshold-microvolt = <4500000>;
+ re-charge-voltage-microvolt = <250000>;
+ voltage-min-design-microvolt = <3200000>;
+ voltage-max-design-microvolt = <4200000>;
+ energy-full-design-microwatt-hours = <5290000>;
+ charge-full-design-microamp-hours = <1430000>;
+ precharge-current-microamp = <256000>;
+ precharge-upper-limit-microvolt = <2500000>;
+ charge-term-current-microamp = <128000>;
+ constant-charge-current-max-microamp = <900000>;
+ constant-charge-voltage-max-microvolt = <4200000>;
+ factory-internal-resistance-micro-ohms = <250000>;
+ ocv-capacity-celsius = <(-10) 10>;
+ ocv-capacity-table-0 = <4185000 100>, <4113000 95>, <4066000 90>;
+ resistance-temp-table = <20 100>, <10 90>, <0 80>, <(-10) 60>;
+ };
+
+ charger@11 {
+ reg = <0x11>;
+ monitored-battery = <&battery>;
+ };
+
+ fuel-gauge@22 {
+ reg = <0x22>;
+ monitored-battery = <&battery>;
+ };
+ };
--
2.27.0
Hi Ricardo and Dan,
On Tue, Jul 28, 2020 at 03:08:12PM -0500, Ricardo Rivera-Matos wrote:
> From: Dan Murphy <[email protected]>
>
> Convert the battery.txt file to yaml and fix up the examples.
>
> Signed-off-by: Dan Murphy <[email protected]>
> Reviewed-by: Rob Herring <[email protected]>
> ---
I merged this doing some modifcations while applying, so that this
is not postponed and risking conflicts due to added properties:
> [...]
> +patternProperties:
> + '^ocv-capacity-table-[0-100]$':
> [...]
[0-100] is a valid regex, but counterintuitively only allows 0 and
1. For example it does not apply for ocv-capacity-table-2.
I used [0-9]+ instead, which is being used by pinctrl.
> +examples:
> + - |
> + power {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + battery: battery {
> + compatible = "simple-battery";
> + over-voltage-threshold-microvolt = <4500000>;
> + re-charge-voltage-microvolt = <250000>;
> + voltage-min-design-microvolt = <3200000>;
> + voltage-max-design-microvolt = <4200000>;
> + energy-full-design-microwatt-hours = <5290000>;
> + charge-full-design-microamp-hours = <1430000>;
> + precharge-current-microamp = <256000>;
> + precharge-upper-limit-microvolt = <2500000>;
> + charge-term-current-microamp = <128000>;
> + constant-charge-current-max-microamp = <900000>;
> + constant-charge-voltage-max-microvolt = <4200000>;
> + factory-internal-resistance-micro-ohms = <250000>;
> + ocv-capacity-celsius = <(-10) 10>;
You state, that there is a table for -10 degrees and one for 10
degrees...
> + ocv-capacity-table-0 = <4185000 100>, <4113000 95>, <4066000 90>;
... and then you provide only the table for -10 degrees. I fixed
this by simply using the previous example (tables for -10, 0 and 10
degrees) and 3 tables and added a comment above the tables.
-- Sebastian