The KSZ9031 PHY skew timings for rxc/txc, originally set to achieve
the desired phase shift between clock- and data-signal, now trigger a
kernel warning when used in rgmii-id mode:
*-skew-ps values should be used only with phy-mode = "rgmii"
This is because commit bcf3440c6dd7 ("net: phy: micrel: add phy-mode
support for the KSZ9031 PHY") now configures own timings when
phy-mode = "rgmii-id". Device trees wanting to set their own delays
should use phy-mode "rgmii" instead as the warning prescribes.
The "standard" timings now used with "rgmii-id" work fine on this
board, so drop the explicit timings in the device tree and thereby
silence the warning.
Fixes: 666b5ca85cd3 ("ARM: dts: stm32: add STM32MP1-based Linux Automation MC-1 board")
Signed-off-by: Holger Assmann <[email protected]>
---
arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts | 2 --
1 file changed, 2 deletions(-)
diff --git a/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts b/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts
index 5700e6b700d3..b85025d00943 100644
--- a/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts
+++ b/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts
@@ -121,8 +121,6 @@
reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>; /* ETH_RST# */
interrupt-parent = <&gpioa>;
interrupts = <6 IRQ_TYPE_EDGE_FALLING>; /* ETH_MDINT# */
- rxc-skew-ps = <1860>;
- txc-skew-ps = <1860>;
reset-assert-us = <10000>;
reset-deassert-us = <300>;
micrel,force-master;
--
2.20.1
On 8/7/20 5:03 PM, Holger Assmann wrote:
> The KSZ9031 PHY skew timings for rxc/txc, originally set to achieve
> the desired phase shift between clock- and data-signal, now trigger a
> kernel warning when used in rgmii-id mode:
>
> *-skew-ps values should be used only with phy-mode = "rgmii"
>
> This is because commit bcf3440c6dd7 ("net: phy: micrel: add phy-mode
> support for the KSZ9031 PHY") now configures own timings when
> phy-mode = "rgmii-id". Device trees wanting to set their own delays
> should use phy-mode "rgmii" instead as the warning prescribes.
>
> The "standard" timings now used with "rgmii-id" work fine on this
> board, so drop the explicit timings in the device tree and thereby
> silence the warning.
>
> Fixes: 666b5ca85cd3 ("ARM: dts: stm32: add STM32MP1-based Linux Automation MC-1 board")
> Signed-off-by: Holger Assmann <[email protected]>
Acked-by: Ahmad Fatoum <[email protected]>
> ---
> arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts | 2 --
> 1 file changed, 2 deletions(-)
>
> diff --git a/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts b/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts
> index 5700e6b700d3..b85025d00943 100644
> --- a/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts
> +++ b/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts
> @@ -121,8 +121,6 @@
> reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>; /* ETH_RST# */
> interrupt-parent = <&gpioa>;
> interrupts = <6 IRQ_TYPE_EDGE_FALLING>; /* ETH_MDINT# */
> - rxc-skew-ps = <1860>;
> - txc-skew-ps = <1860>;
> reset-assert-us = <10000>;
> reset-deassert-us = <300>;
> micrel,force-master;
>
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
On 8/7/20 5:24 PM, Ahmad Fatoum wrote:
> On 8/7/20 5:03 PM, Holger Assmann wrote:
>> The KSZ9031 PHY skew timings for rxc/txc, originally set to achieve
>> the desired phase shift between clock- and data-signal, now trigger a
>> kernel warning when used in rgmii-id mode:
>>
>> *-skew-ps values should be used only with phy-mode = "rgmii"
>>
>> This is because commit bcf3440c6dd7 ("net: phy: micrel: add phy-mode
>> support for the KSZ9031 PHY") now configures own timings when
>> phy-mode = "rgmii-id". Device trees wanting to set their own delays
>> should use phy-mode "rgmii" instead as the warning prescribes.
>>
>> The "standard" timings now used with "rgmii-id" work fine on this
>> board, so drop the explicit timings in the device tree and thereby
>> silence the warning.
>>
>> Fixes: 666b5ca85cd3 ("ARM: dts: stm32: add STM32MP1-based Linux Automation MC-1 board")
>> Signed-off-by: Holger Assmann <[email protected]>
>
> Acked-by: Ahmad Fatoum <[email protected]>
Typo Correction: Acked-by: Ahmad Fatoum <[email protected]>
:-)
>
>> ---
>> arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts | 2 --
>> 1 file changed, 2 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts b/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts
>> index 5700e6b700d3..b85025d00943 100644
>> --- a/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts
>> +++ b/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts
>> @@ -121,8 +121,6 @@
>> reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>; /* ETH_RST# */
>> interrupt-parent = <&gpioa>;
>> interrupts = <6 IRQ_TYPE_EDGE_FALLING>; /* ETH_MDINT# */
>> - rxc-skew-ps = <1860>;
>> - txc-skew-ps = <1860>;
>> reset-assert-us = <10000>;
>> reset-deassert-us = <300>;
>> micrel,force-master;
>>
>
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Hi Holger
On 8/7/20 5:03 PM, Holger Assmann wrote:
> The KSZ9031 PHY skew timings for rxc/txc, originally set to achieve
> the desired phase shift between clock- and data-signal, now trigger a
> kernel warning when used in rgmii-id mode:
>
> *-skew-ps values should be used only with phy-mode = "rgmii"
>
> This is because commit bcf3440c6dd7 ("net: phy: micrel: add phy-mode
> support for the KSZ9031 PHY") now configures own timings when
> phy-mode = "rgmii-id". Device trees wanting to set their own delays
> should use phy-mode "rgmii" instead as the warning prescribes.
>
> The "standard" timings now used with "rgmii-id" work fine on this
> board, so drop the explicit timings in the device tree and thereby
> silence the warning.
>
> Fixes: 666b5ca85cd3 ("ARM: dts: stm32: add STM32MP1-based Linux Automation MC-1 board")
> Signed-off-by: Holger Assmann <[email protected]>
> ---
> arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts | 2 --
> 1 file changed, 2 deletions(-)
>
> diff --git a/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts b/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts
> index 5700e6b700d3..b85025d00943 100644
> --- a/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts
> +++ b/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts
> @@ -121,8 +121,6 @@
> reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>; /* ETH_RST# */
> interrupt-parent = <&gpioa>;
> interrupts = <6 IRQ_TYPE_EDGE_FALLING>; /* ETH_MDINT# */
> - rxc-skew-ps = <1860>;
> - txc-skew-ps = <1860>;
> reset-assert-us = <10000>;
> reset-deassert-us = <300>;
> micrel,force-master;
>
Applied on stm32-next.
Thanks.
Alex