There might be some requests pending in the buffer when the
interface close sequence occurs. In some devices, these
pending requests might lead to the module not shutting down
properly when m_can_clk_stop() is called.
Therefore, move the device to init state before potentially
powering it down.
Signed-off-by: Faiz Abbas <[email protected]>
---
changes since v1: Rebased to latest mainline
drivers/net/can/m_can/m_can.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/net/can/m_can/m_can.c b/drivers/net/can/m_can/m_can.c
index 02c5795b7393..d0c458f7f6e1 100644
--- a/drivers/net/can/m_can/m_can.c
+++ b/drivers/net/can/m_can/m_can.c
@@ -1414,6 +1414,9 @@ static void m_can_stop(struct net_device *dev)
/* disable all interrupts */
m_can_disable_all_interrupts(cdev);
+ /* Set init mode to disengage from the network */
+ m_can_config_endisable(cdev, true);
+
/* set the state as STOPPED */
cdev->can.state = CAN_STATE_STOPPED;
}
--
2.17.1
Faiz
On 8/25/20 12:54 AM, Faiz Abbas wrote:
> There might be some requests pending in the buffer when the
> interface close sequence occurs. In some devices, these
> pending requests might lead to the module not shutting down
> properly when m_can_clk_stop() is called.
>
> Therefore, move the device to init state before potentially
> powering it down.
>
> Signed-off-by: Faiz Abbas <[email protected]>
> ---
>
> changes since v1: Rebased to latest mainline
>
> drivers/net/can/m_can/m_can.c | 3 +++
> 1 file changed, 3 insertions(+)
>
> diff --git a/drivers/net/can/m_can/m_can.c b/drivers/net/can/m_can/m_can.c
> index 02c5795b7393..d0c458f7f6e1 100644
> --- a/drivers/net/can/m_can/m_can.c
> +++ b/drivers/net/can/m_can/m_can.c
> @@ -1414,6 +1414,9 @@ static void m_can_stop(struct net_device *dev)
> /* disable all interrupts */
> m_can_disable_all_interrupts(cdev);
>
> + /* Set init mode to disengage from the network */
> + m_can_config_endisable(cdev, true);
> +
> /* set the state as STOPPED */
> cdev->can.state = CAN_STATE_STOPPED;
> }
Acked-by: Dan Murphy <[email protected]>
On 8/25/20 7:54 AM, Faiz Abbas wrote:
> There might be some requests pending in the buffer when the
> interface close sequence occurs. In some devices, these
> pending requests might lead to the module not shutting down
> properly when m_can_clk_stop() is called.
>
> Therefore, move the device to init state before potentially
> powering it down.
>
> Signed-off-by: Faiz Abbas <[email protected]>
Added to linux-can/testing.
Tnx,
Marc
--
Pengutronix e.K. | Marc Kleine-Budde |
Embedded Linux | https://www.pengutronix.de |
Vertretung West/Dortmund | Phone: +49-231-2826-924 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |