The HDMI controllers found in the BCM2711 SoC need some adjustments to the
bindings, especially since the registers have been shuffled around in more
register ranges.
Reviewed-by: Rob Herring <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
---
Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml | 109 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++-
1 file changed, 109 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
diff --git a/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml b/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
new file mode 100644
index 000000000000..6091fe3d315b
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
@@ -0,0 +1,109 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/brcm,bcm2711-hdmi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom BCM2711 HDMI Controller Device Tree Bindings
+
+maintainers:
+ - Eric Anholt <[email protected]>
+
+properties:
+ compatible:
+ enum:
+ - brcm,bcm2711-hdmi0
+ - brcm,bcm2711-hdmi1
+
+ reg:
+ items:
+ - description: HDMI controller register range
+ - description: DVP register range
+ - description: HDMI PHY register range
+ - description: Rate Manager register range
+ - description: Packet RAM register range
+ - description: Metadata RAM register range
+ - description: CSC register range
+ - description: CEC register range
+ - description: HD register range
+
+ reg-names:
+ items:
+ - const: hdmi
+ - const: dvp
+ - const: phy
+ - const: rm
+ - const: packet
+ - const: metadata
+ - const: csc
+ - const: cec
+ - const: hd
+
+ clocks:
+ description: The HDMI state machine clock
+
+ clock-names:
+ const: hdmi
+
+ ddc:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/phandle
+ description: >
+ Phandle of the I2C controller used for DDC EDID probing
+
+ hpd-gpios:
+ description: >
+ The GPIO pin for the HDMI hotplug detect (if it doesn't appear
+ as an interrupt/status bit in the HDMI controller itself)
+
+ dmas:
+ maxItems: 1
+ description: >
+ Should contain one entry pointing to the DMA channel used to
+ transfer audio data.
+
+ dma-names:
+ const: audio-rx
+
+ resets:
+ maxItems: 1
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - clocks
+ - resets
+ - ddc
+
+additionalProperties: false
+
+examples:
+ - |
+ hdmi0: hdmi@7ef00700 {
+ compatible = "brcm,bcm2711-hdmi0";
+ reg = <0x7ef00700 0x300>,
+ <0x7ef00300 0x200>,
+ <0x7ef00f00 0x80>,
+ <0x7ef00f80 0x80>,
+ <0x7ef01b00 0x200>,
+ <0x7ef01f00 0x400>,
+ <0x7ef00200 0x80>,
+ <0x7ef04300 0x100>,
+ <0x7ef20000 0x100>;
+ reg-names = "hdmi",
+ "dvp",
+ "phy",
+ "rm",
+ "packet",
+ "metadata",
+ "csc",
+ "cec",
+ "hd";
+ clocks = <&firmware_clocks 13>;
+ clock-names = "hdmi";
+ resets = <&dvp 0>;
+ ddc = <&ddc0>;
+ };
+
+...
--
git-series 0.9.1
Hi Maxime,
On 7/9/20 2:42 AM, Maxime Ripard wrote:
> The HDMI controllers found in the BCM2711 SoC need some adjustments to the
> bindings, especially since the registers have been shuffled around in more
> register ranges.
>
> Reviewed-by: Rob Herring <[email protected]>
> Signed-off-by: Maxime Ripard <[email protected]>
> ---
> Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml | 109 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++-
> 1 file changed, 109 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
>
> diff --git a/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml b/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
> new file mode 100644
> index 000000000000..6091fe3d315b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
> @@ -0,0 +1,109 @@
> +# SPDX-License-Identifier: GPL-2.0
> +%YAML 1.2
> +---
> +$id: https://protect2.fireeye.com/url?k=556aeb05-08b8fda0-556b604a-0cc47a31bee8-c3a0ebd1d22c3183&q=1&u=http%3A%2F%2Fdevicetree.org%2Fschemas%2Fdisplay%2Fbrcm%2Cbcm2711-hdmi.yaml%23
> +$schema: https://protect2.fireeye.com/url?k=24fa660c-792870a9-24fbed43-0cc47a31bee8-0bf16f4fd60f0ab4&q=1&u=http%3A%2F%2Fdevicetree.org%2Fmeta-schemas%2Fcore.yaml%23
> +
> +title: Broadcom BCM2711 HDMI Controller Device Tree Bindings
> +
> +maintainers:
> + - Eric Anholt <[email protected]>
> +
> +properties:
> + compatible:
> + enum:
> + - brcm,bcm2711-hdmi0
> + - brcm,bcm2711-hdmi1
> +
> + reg:
> + items:
> + - description: HDMI controller register range
> + - description: DVP register range
> + - description: HDMI PHY register range
> + - description: Rate Manager register range
> + - description: Packet RAM register range
> + - description: Metadata RAM register range
> + - description: CSC register range
> + - description: CEC register range
> + - description: HD register range
> +
> + reg-names:
> + items:
> + - const: hdmi
> + - const: dvp
> + - const: phy
> + - const: rm
> + - const: packet
> + - const: metadata
> + - const: csc
> + - const: cec
> + - const: hd
> +
> + clocks:
> + description: The HDMI state machine clock
I'm not sure the following description is correct.
But, this description doesn't contain the information of audio clock.
description: The HDMI state machine and audio clock
> +
> + clock-names:
> + const: hdmi
This patch is missing the following clock information for audio clock.
const: clk-108M
> +
> + ddc:
> + allOf:
> + - $ref: /schemas/types.yaml#/definitions/phandle
> + description: >
> + Phandle of the I2C controller used for DDC EDID probing
> +
> + hpd-gpios:
> + description: >
> + The GPIO pin for the HDMI hotplug detect (if it doesn't appear
> + as an interrupt/status bit in the HDMI controller itself)
> +
> + dmas:
> + maxItems: 1
> + description: >
> + Should contain one entry pointing to the DMA channel used to
> + transfer audio data.
> +
> + dma-names:
> + const: audio-rx
> +
> + resets:
> + maxItems: 1
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - clocks
> + - resets
> + - ddc
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + hdmi0: hdmi@7ef00700 {
> + compatible = "brcm,bcm2711-hdmi0";
> + reg = <0x7ef00700 0x300>,
> + <0x7ef00300 0x200>,
> + <0x7ef00f00 0x80>,
> + <0x7ef00f80 0x80>,
> + <0x7ef01b00 0x200>,
> + <0x7ef01f00 0x400>,
> + <0x7ef00200 0x80>,
> + <0x7ef04300 0x100>,
> + <0x7ef20000 0x100>;
> + reg-names = "hdmi",
> + "dvp",
> + "phy",
> + "rm",
> + "packet",
> + "metadata",
> + "csc",
> + "cec",
> + "hd";
> + clocks = <&firmware_clocks 13>;
> + clock-names = "hdmi";
Also, this example doesn't include the instance of audio clock.
Need to edit them as following:
clock-names = "hdmi", "clk-108M";
clocks = <&firmware_clocks 13>, <&dvp 0>;
> + resets = <&dvp 0>;
> + ddc = <&ddc0>;
> + };
> +
> +...
>
--
Best Regards,
Chanwoo Choi
Samsung Electronics
Hi,
On Tue, Sep 01, 2020 at 01:45:07PM +0900, Chanwoo Choi wrote:
> Hi Maxime,
>
> On 7/9/20 2:42 AM, Maxime Ripard wrote:
> > The HDMI controllers found in the BCM2711 SoC need some adjustments to the
> > bindings, especially since the registers have been shuffled around in more
> > register ranges.
> >
> > Reviewed-by: Rob Herring <[email protected]>
> > Signed-off-by: Maxime Ripard <[email protected]>
> > ---
> > Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml | 109 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++-
> > 1 file changed, 109 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
> >
> > diff --git a/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml b/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
> > new file mode 100644
> > index 000000000000..6091fe3d315b
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
> > @@ -0,0 +1,109 @@
> > +# SPDX-License-Identifier: GPL-2.0
> > +%YAML 1.2
> > +---
> > +$id: https://protect2.fireeye.com/url?k=556aeb05-08b8fda0-556b604a-0cc47a31bee8-c3a0ebd1d22c3183&q=1&u=http%3A%2F%2Fdevicetree.org%2Fschemas%2Fdisplay%2Fbrcm%2Cbcm2711-hdmi.yaml%23
> > +$schema: https://protect2.fireeye.com/url?k=24fa660c-792870a9-24fbed43-0cc47a31bee8-0bf16f4fd60f0ab4&q=1&u=http%3A%2F%2Fdevicetree.org%2Fmeta-schemas%2Fcore.yaml%23
> > +
> > +title: Broadcom BCM2711 HDMI Controller Device Tree Bindings
> > +
> > +maintainers:
> > + - Eric Anholt <[email protected]>
> > +
> > +properties:
> > + compatible:
> > + enum:
> > + - brcm,bcm2711-hdmi0
> > + - brcm,bcm2711-hdmi1
> > +
> > + reg:
> > + items:
> > + - description: HDMI controller register range
> > + - description: DVP register range
> > + - description: HDMI PHY register range
> > + - description: Rate Manager register range
> > + - description: Packet RAM register range
> > + - description: Metadata RAM register range
> > + - description: CSC register range
> > + - description: CEC register range
> > + - description: HD register range
> > +
> > + reg-names:
> > + items:
> > + - const: hdmi
> > + - const: dvp
> > + - const: phy
> > + - const: rm
> > + - const: packet
> > + - const: metadata
> > + - const: csc
> > + - const: cec
> > + - const: hd
> > +
> > + clocks:
> > + description: The HDMI state machine clock
>
> I'm not sure the following description is correct.
> But, this description doesn't contain the information of audio clock.
>
> description: The HDMI state machine and audio clock
>
> > +
> > + clock-names:
> > + const: hdmi
>
> This patch is missing the following clock information for audio clock.
>
> const: clk-108M
>
> > +
> > + ddc:
> > + allOf:
> > + - $ref: /schemas/types.yaml#/definitions/phandle
> > + description: >
> > + Phandle of the I2C controller used for DDC EDID probing
> > +
> > + hpd-gpios:
> > + description: >
> > + The GPIO pin for the HDMI hotplug detect (if it doesn't appear
> > + as an interrupt/status bit in the HDMI controller itself)
> > +
> > + dmas:
> > + maxItems: 1
> > + description: >
> > + Should contain one entry pointing to the DMA channel used to
> > + transfer audio data.
> > +
> > + dma-names:
> > + const: audio-rx
> > +
> > + resets:
> > + maxItems: 1
> > +
> > +required:
> > + - compatible
> > + - reg
> > + - reg-names
> > + - clocks
> > + - resets
> > + - ddc
> > +
> > +additionalProperties: false
> > +
> > +examples:
> > + - |
> > + hdmi0: hdmi@7ef00700 {
> > + compatible = "brcm,bcm2711-hdmi0";
> > + reg = <0x7ef00700 0x300>,
> > + <0x7ef00300 0x200>,
> > + <0x7ef00f00 0x80>,
> > + <0x7ef00f80 0x80>,
> > + <0x7ef01b00 0x200>,
> > + <0x7ef01f00 0x400>,
> > + <0x7ef00200 0x80>,
> > + <0x7ef04300 0x100>,
> > + <0x7ef20000 0x100>;
> > + reg-names = "hdmi",
> > + "dvp",
> > + "phy",
> > + "rm",
> > + "packet",
> > + "metadata",
> > + "csc",
> > + "cec",
> > + "hd";
> > + clocks = <&firmware_clocks 13>;
> > + clock-names = "hdmi";
>
> Also, this example doesn't include the instance of audio clock.
> Need to edit them as following:
>
> clock-names = "hdmi", "clk-108M";
> clocks = <&firmware_clocks 13>, <&dvp 0>;
Indeed, thanks for pointing it out
Maxime