2020-09-11 05:11:12

by Oleksij Rempel

[permalink] [raw]
Subject: [PATCH v2 0/3] mainline Plymovent M2M board

changes v2:
- fsl.yaml: reorder ply,plym2m
- imx6dl-plym2m.dts: use hyphen instead of underscore in phy-clock

Oleksij Rempel (3):
dt-bindings: vendor-prefixes: Add an entry for Plymovent
dt-bindings: arm: fsl: add Plymovent M2M board
ARM: dts: add Plymovent M2M board

.../devicetree/bindings/arm/fsl.yaml | 1 +
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-plym2m.dts | 394 ++++++++++++++++++
4 files changed, 398 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts

--
2.28.0


2020-09-11 05:11:57

by Oleksij Rempel

[permalink] [raw]
Subject: [PATCH v2 3/3] ARM: dts: add Plymovent M2M board

Plymovent M2M is a control interface produced for the Plymovent filter
systems.

Signed-off-by: David Jander <[email protected]>
Signed-off-by: Oleksij Rempel <[email protected]>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-plym2m.dts | 394 ++++++++++++++++++++++++++++
2 files changed, 395 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 4572db3fa5ae..3c3811fd8613 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -455,6 +455,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-pico-hobbit.dtb \
imx6dl-pico-nymph.dtb \
imx6dl-pico-pi.dtb \
+ imx6dl-plym2m.dtb \
imx6dl-prtrvt.dtb \
imx6dl-prtvt7.dtb \
imx6dl-rex-basic.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
new file mode 100644
index 000000000000..4f96e05aa03f
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
@@ -0,0 +1,394 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+// SPDX-FileCopyrightText: 2014 Protonic Holland
+// SPDX-FileCopyrightText: 2020 Oleksij Rempel <[email protected]>, Pengutronix
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx6dl.dtsi"
+
+/ {
+ model = "Plymovent M2M board";
+ compatible = "ply,plym2m", "fsl,imx6dl";
+
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 500000 0>;
+ brightness-levels = <0 1000>;
+ num-interpolated-steps = <20>;
+ default-brightness-level = <19>;
+ power-supply = <&reg_12v0>;
+ };
+
+ display {
+ compatible = "fsl,imx-parallel-display";
+ pinctrl-0 = <&pinctrl_ipu1_disp>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ display_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ led-debug {
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ panel {
+ compatible = "edt,etm0700g0bdh6";
+ backlight = <&backlight>;
+ power-supply = <&reg_3v3>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+
+ clk50m_phy: phy-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <50000000>;
+ };
+
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_5v0: regulator-5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ reg_12v0: regulator-12v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "12v0";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1>;
+ xceiver-supply = <&reg_5v0>;
+ status = "okay";
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rmii";
+ clocks = <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET>,
+ <&clk50m_phy>;
+ clock-names = "ipg", "ahb", "ptp";
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip KSZ8081RNA PHY */
+ rgmii_phy: ethernet-phy@0 {
+ reg = <0>;
+ interrupts-extended = <&gpio5 23 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&gpio1 {
+ gpio-line-names =
+ "CAN1_TERM", "SD1_CD", "", "", "", "", "", "",
+ "DEBUG_0", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio2 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "ECSPI2_SS0", "", "", "", "TSC_BUSY", "";
+};
+
+&gpio3 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "ECSPI1_SS1", "TSC_PENIRQ", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "CAN1_SR", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio5 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "ETH_RESET", "ETH_INTRP",
+ "", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ /* additional i2c devices are added automatically by the boot loader */
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ temperature-sensor@70 {
+ compatible = "ti,tmp103";
+ reg = <0x70>;
+ };
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display_in>;
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usbphynop1 {
+ status = "disabled";
+};
+
+&usbphynop2 {
+ status = "disabled";
+};
+
+&usbotg {
+ phy_type = "utmi";
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ disable-wp;
+ cap-sd-highspeed;
+ no-mmc;
+ no-sdio;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ bus-width = <8>;
+ no-1-8-v;
+ non-removable;
+ no-sd;
+ no-sdio;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_can1: can1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008
+ /* CAN1_SR */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008
+ /* CAN1_TERM */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b088
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x1b000
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x3008
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x3008
+ /* CS */
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x3008
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ /* MX6QDL_ENET_PINGRP4 */
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
+ /* Phy reset */
+ MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0
+ /* nINTRP */
+ MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_ipu1_disp: ipudisp1grp {
+ fsl,pins = <
+ /* DSE 0x30 => 25 Ohm, 0x20 => 37 Ohm, 0x10 => 75 Ohm */
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x30
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x30
+ MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x30
+ MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x30
+ MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x30
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x30
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x30
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x30
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x30
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x30
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x30
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x30
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x30
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x30
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x30
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x30
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x30
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x30
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x30
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x30
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x30
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x30
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__PWM1_OUT 0x8
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
+ MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
+ MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
+ >;
+ };
+};
--
2.28.0

2020-09-11 05:13:17

by Oleksij Rempel

[permalink] [raw]
Subject: [PATCH v2 1/3] dt-bindings: vendor-prefixes: Add an entry for Plymovent

Add "ply" entry for Plymovent Group BV: https://www.plymovent.com/

Signed-off-by: Oleksij Rempel <[email protected]>
---
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 2baee2c817c1..60b59ca04066 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -818,6 +818,8 @@ patternProperties:
description: PLDA
"^plx,.*":
description: Broadcom Corporation (formerly PLX Technology)
+ "^ply,.*":
+ description: Plymovent Group BV
"^pni,.*":
description: PNI Sensor Corporation
"^pocketbook,.*":
--
2.28.0

2020-09-11 06:04:20

by Marco Felsch

[permalink] [raw]
Subject: Re: [PATCH v2 3/3] ARM: dts: add Plymovent M2M board

On 20-09-11 07:09, Oleksij Rempel wrote:
> Plymovent M2M is a control interface produced for the Plymovent filter
> systems.
>
> Signed-off-by: David Jander <[email protected]>
> Signed-off-by: Oleksij Rempel <[email protected]>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx6dl-plym2m.dts | 394 ++++++++++++++++++++++++++++
> 2 files changed, 395 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 4572db3fa5ae..3c3811fd8613 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -455,6 +455,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6dl-pico-hobbit.dtb \
> imx6dl-pico-nymph.dtb \
> imx6dl-pico-pi.dtb \
> + imx6dl-plym2m.dtb \
> imx6dl-prtrvt.dtb \
> imx6dl-prtvt7.dtb \
> imx6dl-rex-basic.dtb \
> diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
> new file mode 100644
> index 000000000000..4f96e05aa03f
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
> @@ -0,0 +1,394 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +// SPDX-FileCopyrightText: 2014 Protonic Holland
> +// SPDX-FileCopyrightText: 2020 Oleksij Rempel <[email protected]>, Pengutronix
^
@shawn: I saw a few patches adding these tags. Are they used in the near
future?

Regards,
Marco

2020-09-13 04:51:14

by Shawn Guo

[permalink] [raw]
Subject: Re: [PATCH v2 3/3] ARM: dts: add Plymovent M2M board

On Fri, Sep 11, 2020 at 08:03:12AM +0200, Marco Felsch wrote:
> On 20-09-11 07:09, Oleksij Rempel wrote:
> > Plymovent M2M is a control interface produced for the Plymovent filter
> > systems.
> >
> > Signed-off-by: David Jander <[email protected]>
> > Signed-off-by: Oleksij Rempel <[email protected]>
> > ---
> > arch/arm/boot/dts/Makefile | 1 +
> > arch/arm/boot/dts/imx6dl-plym2m.dts | 394 ++++++++++++++++++++++++++++
> > 2 files changed, 395 insertions(+)
> > create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts
> >
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index 4572db3fa5ae..3c3811fd8613 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -455,6 +455,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> > imx6dl-pico-hobbit.dtb \
> > imx6dl-pico-nymph.dtb \
> > imx6dl-pico-pi.dtb \
> > + imx6dl-plym2m.dtb \
> > imx6dl-prtrvt.dtb \
> > imx6dl-prtvt7.dtb \
> > imx6dl-rex-basic.dtb \
> > diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
> > new file mode 100644
> > index 000000000000..4f96e05aa03f
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
> > @@ -0,0 +1,394 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> > +// SPDX-FileCopyrightText: 2014 Protonic Holland
> > +// SPDX-FileCopyrightText: 2020 Oleksij Rempel <[email protected]>, Pengutronix
> ^
> @shawn: I saw a few patches adding these tags. Are they used in the near
> future?

I'm not sure. I haven't seen this in Documentation/process/license-rules.rst,
nor the discussion around this.

Shawn

2020-09-21 05:24:43

by Oleksij Rempel

[permalink] [raw]
Subject: Re: [PATCH v2 3/3] ARM: dts: add Plymovent M2M board

On Sun, Sep 13, 2020 at 12:49:45PM +0800, Shawn Guo wrote:
> On Fri, Sep 11, 2020 at 08:03:12AM +0200, Marco Felsch wrote:
> > On 20-09-11 07:09, Oleksij Rempel wrote:
> > > Plymovent M2M is a control interface produced for the Plymovent filter
> > > systems.
> > >
> > > Signed-off-by: David Jander <[email protected]>
> > > Signed-off-by: Oleksij Rempel <[email protected]>
> > > ---
> > > arch/arm/boot/dts/Makefile | 1 +
> > > arch/arm/boot/dts/imx6dl-plym2m.dts | 394 ++++++++++++++++++++++++++++
> > > 2 files changed, 395 insertions(+)
> > > create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts
> > >
> > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > > index 4572db3fa5ae..3c3811fd8613 100644
> > > --- a/arch/arm/boot/dts/Makefile
> > > +++ b/arch/arm/boot/dts/Makefile
> > > @@ -455,6 +455,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> > > imx6dl-pico-hobbit.dtb \
> > > imx6dl-pico-nymph.dtb \
> > > imx6dl-pico-pi.dtb \
> > > + imx6dl-plym2m.dtb \
> > > imx6dl-prtrvt.dtb \
> > > imx6dl-prtvt7.dtb \
> > > imx6dl-rex-basic.dtb \
> > > diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
> > > new file mode 100644
> > > index 000000000000..4f96e05aa03f
> > > --- /dev/null
> > > +++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
> > > @@ -0,0 +1,394 @@
> > > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> > > +// SPDX-FileCopyrightText: 2014 Protonic Holland
> > > +// SPDX-FileCopyrightText: 2020 Oleksij Rempel <[email protected]>, Pengutronix
> > ^
> > @shawn: I saw a few patches adding these tags. Are they used in the near
> > future?
>
> I'm not sure. I haven't seen this in Documentation/process/license-rules.rst,
> nor the discussion around this.

Hi Shawn,

is it a no go? Should I send a patch with old style copyright text?


Regards,
Oleksij
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |

2020-09-22 03:08:56

by Shawn Guo

[permalink] [raw]
Subject: Re: [PATCH v2 3/3] ARM: dts: add Plymovent M2M board

On Mon, Sep 21, 2020 at 07:23:13AM +0200, Oleksij Rempel wrote:
> On Sun, Sep 13, 2020 at 12:49:45PM +0800, Shawn Guo wrote:
> > On Fri, Sep 11, 2020 at 08:03:12AM +0200, Marco Felsch wrote:
> > > On 20-09-11 07:09, Oleksij Rempel wrote:
> > > > Plymovent M2M is a control interface produced for the Plymovent filter
> > > > systems.
> > > >
> > > > Signed-off-by: David Jander <[email protected]>
> > > > Signed-off-by: Oleksij Rempel <[email protected]>
> > > > ---
> > > > arch/arm/boot/dts/Makefile | 1 +
> > > > arch/arm/boot/dts/imx6dl-plym2m.dts | 394 ++++++++++++++++++++++++++++
> > > > 2 files changed, 395 insertions(+)
> > > > create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts
> > > >
> > > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > > > index 4572db3fa5ae..3c3811fd8613 100644
> > > > --- a/arch/arm/boot/dts/Makefile
> > > > +++ b/arch/arm/boot/dts/Makefile
> > > > @@ -455,6 +455,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> > > > imx6dl-pico-hobbit.dtb \
> > > > imx6dl-pico-nymph.dtb \
> > > > imx6dl-pico-pi.dtb \
> > > > + imx6dl-plym2m.dtb \
> > > > imx6dl-prtrvt.dtb \
> > > > imx6dl-prtvt7.dtb \
> > > > imx6dl-rex-basic.dtb \
> > > > diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
> > > > new file mode 100644
> > > > index 000000000000..4f96e05aa03f
> > > > --- /dev/null
> > > > +++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
> > > > @@ -0,0 +1,394 @@
> > > > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> > > > +// SPDX-FileCopyrightText: 2014 Protonic Holland
> > > > +// SPDX-FileCopyrightText: 2020 Oleksij Rempel <[email protected]>, Pengutronix
> > > ^
> > > @shawn: I saw a few patches adding these tags. Are they used in the near
> > > future?
> >
> > I'm not sure. I haven't seen this in Documentation/process/license-rules.rst,
> > nor the discussion around this.
>
> Hi Shawn,
>
> is it a no go? Should I send a patch with old style copyright text?

Yeah, I would rather stay with the existing style before there is a
clear direction to the new one.

Also the vendor-prefixes patch needs an ACK from Rob.

Shawn