From: Camel Guo <[email protected]>
Add properties for configuring the General Purpose Input Output (GPIO).
There are 2 settings for GPIO, configuration and the output drive type.
Signed-off-by: Camel Guo <[email protected]>
Acked-by: Dan Murphy <[email protected]>
---
v3:
- Fix typo
- Add Acked-By from Dan
.../bindings/sound/tlv320adcx140.yaml | 44 +++++++++++++++++++
1 file changed, 44 insertions(+)
diff --git a/Documentation/devicetree/bindings/sound/tlv320adcx140.yaml b/Documentation/devicetree/bindings/sound/tlv320adcx140.yaml
index f578f17f3e04..2f95ccde4dc3 100644
--- a/Documentation/devicetree/bindings/sound/tlv320adcx140.yaml
+++ b/Documentation/devicetree/bindings/sound/tlv320adcx140.yaml
@@ -134,6 +134,49 @@ patternProperties:
4d - Drive weak low and active high
5d - Drive Hi-Z and active high
+ ti,gpio-config:
+ description: |
+ Defines the configuration and output drive for the General Purpose
+ Input and Output pin (GPIO1). Its value is a pair, the first value is for
+ the configuration type and the second value is for the output drive
+ type. The array is defined as <GPIO1_CFG GPIO1_DRV>
+
+ configuration for the GPIO pin can be one of the following:
+ 0 - disabled
+ 1 - GPIO1 is configured as a general-purpose output (GPO)
+ 2 - (default) GPIO1 is configured as a device interrupt output (IRQ)
+ 3 - GPIO1 is configured as a secondary ASI output (SDOUT2)
+ 4 - GPIO1 is configured as a PDM clock output (PDMCLK)
+ 8 - GPIO1 is configured as an input to control when MICBIAS turns on or
+ off (MICBIAS_EN)
+ 9 - GPIO1 is configured as a general-purpose input (GPI)
+ 10 - GPIO1 is configured as a master clock input (MCLK)
+ 11 - GPIO1 is configured as an ASI input for daisy-chain (SDIN)
+ 12 - GPIO1 is configured as a PDM data input for channel 1 and channel 2
+ (PDMDIN1)
+ 13 - GPIO1 is configured as a PDM data input for channel 3 and channel 4
+ (PDMDIN2)
+ 14 - GPIO1 is configured as a PDM data input for channel 5 and channel 6
+ (PDMDIN3)
+ 15 - GPIO1 is configured as a PDM data input for channel 7 and channel 8
+ (PDMDIN4)
+
+ output drive type for the GPIO pin can be one of the following:
+ 0 - Hi-Z output
+ 1 - Drive active low and active high
+ 2 - (default) Drive active low and weak high
+ 3 - Drive active low and Hi-Z
+ 4 - Drive weak low and active high
+ 5 - Drive Hi-Z and active high
+
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32-array
+ - minItems: 2
+ maxItems: 2
+ items:
+ maximum: 15
+ default: [2, 2]
+
required:
- compatible
- reg
@@ -150,6 +193,7 @@ examples:
ti,mic-bias-source = <6>;
ti,pdm-edge-select = <0 1 0 1>;
ti,gpi-config = <4 5 6 7>;
+ ti,gpio-config = <10 2>;
ti,gpo-config-1 = <0 0>;
ti,gpo-config-2 = <0 0>;
reset-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
--
2.20.1
On Wed, 16 Sep 2020 09:59:48 +0200, Camel Guo wrote:
> Add properties for configuring the General Purpose Input Output (GPIO).
> There are 2 settings for GPIO, configuration and the output drive type.
Applied to
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-next
Thanks!
[1/2] dt-bindings: tlv320adcx140: Add GPIO config and drive config
commit: 15b3d324c8980022071710b5096b705eb6b74fca
[2/2] ASoC: tlv320adcx140: Add support for configuring GPIO pin
commit: d5214321498a43558d9ffcce4153775c2c296bad
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
Thanks,
Mark