Add a binding for the Variscite Symphony evaluation kit board with
VAR-SOM-MX8MN System on Module.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 37cef8653541..8a8284715baf 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -363,6 +363,12 @@ properties:
- fsl,imx8mn-evk # i.MX8MN LPDDR4 EVK Board
- const: fsl,imx8mn
+ - description: Variscite VAR-SOM-MX8MN based boards
+ items:
+ - const: variscite,var-som-mx8mn-symphony
+ - const: variscite,var-som-mx8mn
+ - const: fsl,imx8mn
+
- description: i.MX8MP based Boards
items:
- enum:
--
2.17.1
Add DTSI of Variscite VAR-SOM-MX8MN (Nano) System on Module in a basic
version, delivered with Variscite Symphony Evaluation kit. This version
comes with:
- 1 GB of RAM,
- 16 GB eMMC,
- Gigabit Ethernet PHY,
- 802.11 ac/a/b/g/n WiFi with 4.2 Bluetooth,
- CAN bus,
- Audio codec (not yet configured in DTSI).
Signed-off-by: Krzysztof Kozlowski <[email protected]>
---
Changes since v1:
1. Add Variscite copyright. The work was based on my previous
imx8mm-var-som work which was based on imx8mm-evk, however few device
nodes were configured based on Variscite GPLv2 work.
2. Set PMIC interrupt as edge rising which is not strictly correct, but
it seems to not cause IRQ storm and matches previous GPIO_ACTIVE_LOW
incorrect flag. I reached to Variscite but did not get proper answer
except "there should be a pull up", which does not work in reality.
Something is wrong here...
---
.../boot/dts/freescale/imx8mn-var-som.dtsi | 551 ++++++++++++++++++
1 file changed, 551 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mn-var-som.dtsi
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-var-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-var-som.dtsi
new file mode 100644
index 000000000000..a2d0190921e4
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mn-var-som.dtsi
@@ -0,0 +1,551 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 NXP
+ * Copyright 2019-2020 Variscite Ltd.
+ * Copyright (C) 2020 Krzysztof Kozlowski <[email protected]>
+ */
+
+#include "imx8mn.dtsi"
+
+/ {
+ model = "Variscite VAR-SOM-MX8MN module";
+ compatible = "variscite,var-som-mx8mn", "fsl,imx8mn";
+
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0x0 0x40000000 0 0x40000000>;
+ };
+
+ reg_eth_phy: regulator-eth-phy {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_eth_phy>;
+ regulator-name = "eth_phy_pwr";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&A53_0 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&A53_1 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&A53_2 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&A53_3 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&ecspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ cs-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>,
+ <&gpio1 0 GPIO_ACTIVE_LOW>;
+ /delete-property/ dmas;
+ /delete-property/ dma-names;
+ status = "okay";
+
+ /* Resistive touch controller */
+ touchscreen@0 {
+ reg = <0>;
+ compatible = "ti,ads7846";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_restouch>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+
+ spi-max-frequency = <1500000>;
+ pendown-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+
+ ti,x-min = /bits/ 16 <125>;
+ touchscreen-size-x = /bits/ 16 <4008>;
+ ti,y-min = /bits/ 16 <282>;
+ touchscreen-size-y = /bits/ 16 <3864>;
+ ti,x-plate-ohms = /bits/ 16 <180>;
+ touchscreen-max-pressure = /bits/ 16 <255>;
+ touchscreen-average-samples = /bits/ 16 <10>;
+ ti,debounce-tol = /bits/ 16 <3>;
+ ti,debounce-rep = /bits/ 16 <1>;
+ ti,settle-delay-usec = /bits/ 16 <150>;
+ ti,keep-vref-on;
+ wakeup-source;
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&pinctrl_fec1>;
+ pinctrl-1 = <&pinctrl_fec1_sleep>;
+ phy-mode = "rgmii";
+ phy-handle = <ðphy>;
+ phy-supply = <®_eth_phy>;
+ fsl,magic-packet;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy@4 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <4>;
+ reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ };
+ };
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ pmic@4b {
+ compatible = "rohm,bd71847";
+ reg = <0x4b>;
+ pinctrl-0 = <&pinctrl_pmic>;
+ interrupt-parent = <&gpio2>;
+ /*
+ * The interrupt is not correct. It should be level low,
+ * however with internal pull up this causes IRQ storm.
+ */
+ interrupts = <8 IRQ_TYPE_EDGE_RISING>;
+ rohm,reset-snvs-powered;
+
+ regulators {
+ buck1_reg: BUCK1 {
+ regulator-name = "buck1";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <1250>;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "buck2";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <1250>;
+ rohm,dvs-run-voltage = <1000000>;
+ rohm,dvs-idle-voltage = <900000>;
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "buck3";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck4_reg: BUCK4 {
+ regulator-name = "buck4";
+ regulator-min-microvolt = <2600000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck5_reg: BUCK5 {
+ regulator-name = "buck5";
+ regulator-min-microvolt = <1605000>;
+ regulator-max-microvolt = <1995000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck6_reg: BUCK6 {
+ regulator-name = "buck6";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo1_reg: LDO1 {
+ regulator-name = "ldo1";
+ regulator-min-microvolt = <1600000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "ldo2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "ldo3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "ldo4";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo5_reg: LDO5 {
+ regulator-compatible = "ldo5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "ldo6";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&i2c3 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ /* TODO: configure audio, as of now just put a placeholder */
+ wm8904: codec@1a {
+ compatible = "wlf,wm8904";
+ reg = <0x1a>;
+ status = "disabled";
+ };
+};
+
+&snvs_pwrkey {
+ status = "okay";
+};
+
+/* Bluetooth */
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ assigned-clocks = <&clk IMX8MN_CLK_UART2>;
+ assigned-clock-parents = <&clk IMX8MN_SYS_PLL1_80M>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+/* Console */
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usbotg1 {
+ dr_mode = "otg";
+ usb-role-switch;
+ status = "okay";
+};
+
+/* WIFI */
+&usdhc1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ bus-width = <4>;
+ non-removable;
+ keep-power-in-suspend;
+ status = "okay";
+
+ brcmf: bcrmf@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+/* SD */
+&usdhc2 {
+ assigned-clocks = <&clk IMX8MN_CLK_USDHC2>;
+ assigned-clock-rates = <200000000>;
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+ cd-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+ bus-width = <4>;
+ vmmc-supply = <®_usdhc2_vmmc>;
+ status = "okay";
+};
+
+/* eMMC */
+&usdhc3 {
+ assigned-clocks = <&clk IMX8MN_CLK_USDHC3_ROOT>;
+ assigned-clock-rates = <400000000>;
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x13
+ MX8MN_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x13
+ MX8MN_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x13
+ MX8MN_IOMUXC_GPIO1_IO14_GPIO1_IO14 0x13
+ MX8MN_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x13
+ >;
+ };
+
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_ENET_MDC_ENET1_MDC 0x3
+ MX8MN_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3
+ MX8MN_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
+ MX8MN_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
+ MX8MN_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
+ MX8MN_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
+ MX8MN_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
+ MX8MN_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
+ MX8MN_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
+ MX8MN_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
+ MX8MN_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
+ MX8MN_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
+ MX8MN_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
+ MX8MN_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
+ MX8MN_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19
+ >;
+ };
+
+ pinctrl_fec1_sleep: fec1sleepgrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_ENET_MDC_GPIO1_IO16 0x120
+ MX8MN_IOMUXC_ENET_MDIO_GPIO1_IO17 0x120
+ MX8MN_IOMUXC_ENET_TD3_GPIO1_IO18 0x120
+ MX8MN_IOMUXC_ENET_TD2_GPIO1_IO19 0x120
+ MX8MN_IOMUXC_ENET_TD1_GPIO1_IO20 0x120
+ MX8MN_IOMUXC_ENET_TD0_GPIO1_IO21 0x120
+ MX8MN_IOMUXC_ENET_RD3_GPIO1_IO29 0x120
+ MX8MN_IOMUXC_ENET_RD2_GPIO1_IO28 0x120
+ MX8MN_IOMUXC_ENET_RD1_GPIO1_IO27 0x120
+ MX8MN_IOMUXC_ENET_RD0_GPIO1_IO26 0x120
+ MX8MN_IOMUXC_ENET_TXC_GPIO1_IO23 0x120
+ MX8MN_IOMUXC_ENET_RXC_GPIO1_IO25 0x120
+ MX8MN_IOMUXC_ENET_RX_CTL_GPIO1_IO24 0x120
+ MX8MN_IOMUXC_ENET_TX_CTL_GPIO1_IO22 0x120
+ MX8MN_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x120
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3
+ MX8MN_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3
+ MX8MN_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3
+ >;
+ };
+
+ pinctrl_pmic: pmicirqgrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD1_DATA6_GPIO2_IO8 0x101
+ >;
+ };
+
+ pinctrl_reg_eth_phy: regethphygrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD1_DATA7_GPIO2_IO9 0x41
+ >;
+ };
+
+ pinctrl_restouch: restouchgrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x1c0
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_SAI3_TXFS_UART2_DCE_RX 0x140
+ MX8MN_IOMUXC_SAI3_TXC_UART2_DCE_TX 0x140
+ MX8MN_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x140
+ MX8MN_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x140
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_UART4_RXD_UART4_DCE_RX 0x140
+ MX8MN_IOMUXC_UART4_TXD_UART4_DCE_TX 0x140
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD1_CLK_USDHC1_CLK 0x190
+ MX8MN_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0
+ MX8MN_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0
+ MX8MN_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0
+ MX8MN_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0
+ MX8MN_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD1_CLK_USDHC1_CLK 0x194
+ MX8MN_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4
+ MX8MN_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4
+ MX8MN_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4
+ MX8MN_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4
+ MX8MN_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD1_CLK_USDHC1_CLK 0x196
+ MX8MN_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6
+ MX8MN_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6
+ MX8MN_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6
+ MX8MN_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6
+ MX8MN_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6
+ >;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x41
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x190
+ MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0
+ MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0
+ MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
+ MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
+ MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
+ MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x194
+ MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
+ MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
+ MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
+ MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
+ MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
+ MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x196
+ MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6
+ MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6
+ MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
+ MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
+ MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
+ MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190
+ MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0
+ MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0
+ MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0
+ MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0
+ MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0
+ MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0
+ MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0
+ MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0
+ MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0
+ MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194
+ MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4
+ MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
+ MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
+ MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
+ MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
+ MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
+ MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
+ MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
+ MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
+ MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196
+ MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6
+ MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6
+ MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6
+ MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6
+ MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6
+ MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6
+ MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6
+ MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6
+ MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6
+ MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
+ >;
+ };
+};
--
2.17.1
Add a basic DTS for Variscite Symphony evaluation kit with VAR-SOM-MX8MN
(i.MX 8M Nano) System on Module. This brings up the board with basic
functionalities although still few issues remain (e.g. I2C3 and USB OTG
port, although it might not be the problem of DTS).
Signed-off-by: Krzysztof Kozlowski <[email protected]>
---
Changes since v1:
1. Add Variscite copyright. The work was based on my previous
imx8mm-var-som work which was based on imx8mm-evk, however few device
nodes were configured based on Variscite GPLv2 work.
2. Drop wakeup-source from RTC.
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../dts/freescale/imx8mn-var-som-symphony.dts | 240 ++++++++++++++++++
2 files changed, 241 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mn-var-som-symphony.dts
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 6b3494b6aa99..28904ebd92cf 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -33,6 +33,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-hummingboard-pulse.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-var-som-symphony.dts b/arch/arm64/boot/dts/freescale/imx8mn-var-som-symphony.dts
new file mode 100644
index 000000000000..f61c48776cf3
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mn-var-som-symphony.dts
@@ -0,0 +1,240 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019-2020 Variscite Ltd.
+ * Copyright (C) 2020 Krzysztof Kozlowski <[email protected]>
+ */
+
+/dts-v1/;
+
+#include "imx8mn-var-som.dtsi"
+
+/ {
+ model = "Variscite VAR-SOM-MX8MN Symphony evaluation board";
+ compatible = "variscite,var-som-mx8mn-symphony", "variscite,var-som-mx8mn", "fsl,imx8mn";
+
+ reg_usdhc2_vmmc: regulator-usdhc2-vmmc {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+ regulator-name = "VSD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio4 22 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ back {
+ label = "Back";
+ gpios = <&pca9534 1 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_BACK>;
+ };
+
+ home {
+ label = "Home";
+ gpios = <&pca9534 2 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_HOME>;
+ };
+
+ menu {
+ label = "Menu";
+ gpios = <&pca9534 3 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_MENU>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led {
+ label = "Heartbeat";
+ gpios = <&pca9534 0 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+ðphy {
+ reset-gpios = <&pca9534 5 GPIO_ACTIVE_HIGH>;
+};
+
+&i2c2 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+
+ pca9534: gpio@20 {
+ compatible = "nxp,pca9534";
+ reg = <0x20>;
+ gpio-controller;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pca9534>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+ #gpio-cells = <2>;
+ wakeup-source;
+
+ /* USB 3.0 OTG (usbotg1) / SATA port switch, set to USB 3.0 */
+ usb3-sata-sel-hog {
+ gpio-hog;
+ gpios = <4 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "usb3_sata_sel";
+ };
+
+ som-vselect-hog {
+ gpio-hog;
+ gpios = <6 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "som_vselect";
+ };
+
+ enet-sel-hog {
+ gpio-hog;
+ gpios = <7 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "enet_sel";
+ };
+ };
+
+ extcon_usbotg1: typec@3d {
+ compatible = "nxp,ptn5150";
+ reg = <0x3d>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ptn5150>;
+ status = "okay";
+ };
+};
+
+&i2c3 {
+ /* Capacitive touch controller */
+ ft5x06_ts: touchscreen@38 {
+ compatible = "edt,edt-ft5406";
+ reg = <0x38>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_captouch>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+
+ touchscreen-size-x = <800>;
+ touchscreen-size-y = <480>;
+ touchscreen-inverted-x;
+ touchscreen-inverted-y;
+ };
+
+ rtc@68 {
+ compatible = "dallas,ds1337";
+ reg = <0x68>;
+ };
+};
+
+/* Header */
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+/* Header */
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&usbotg1 {
+ disable-over-current;
+ extcon = <&extcon_usbotg1>, <&extcon_usbotg1>;
+};
+
+&pinctrl_fec1 {
+ fsl,pins = <
+ MX8MN_IOMUXC_ENET_MDC_ENET1_MDC 0x3
+ MX8MN_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3
+ MX8MN_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
+ MX8MN_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
+ MX8MN_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
+ MX8MN_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
+ MX8MN_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
+ MX8MN_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
+ MX8MN_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
+ MX8MN_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
+ MX8MN_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
+ MX8MN_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
+ MX8MN_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
+ MX8MN_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
+ /* Remove the MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 as not used */
+ >;
+};
+
+&pinctrl_fec1_sleep {
+ fsl,pins = <
+ MX8MN_IOMUXC_ENET_MDC_GPIO1_IO16 0x120
+ MX8MN_IOMUXC_ENET_MDIO_GPIO1_IO17 0x120
+ MX8MN_IOMUXC_ENET_TD3_GPIO1_IO18 0x120
+ MX8MN_IOMUXC_ENET_TD2_GPIO1_IO19 0x120
+ MX8MN_IOMUXC_ENET_TD1_GPIO1_IO20 0x120
+ MX8MN_IOMUXC_ENET_TD0_GPIO1_IO21 0x120
+ MX8MN_IOMUXC_ENET_RD3_GPIO1_IO29 0x120
+ MX8MN_IOMUXC_ENET_RD2_GPIO1_IO28 0x120
+ MX8MN_IOMUXC_ENET_RD1_GPIO1_IO27 0x120
+ MX8MN_IOMUXC_ENET_RD0_GPIO1_IO26 0x120
+ MX8MN_IOMUXC_ENET_TXC_GPIO1_IO23 0x120
+ MX8MN_IOMUXC_ENET_RXC_GPIO1_IO25 0x120
+ MX8MN_IOMUXC_ENET_RX_CTL_GPIO1_IO24 0x120
+ MX8MN_IOMUXC_ENET_TX_CTL_GPIO1_IO22 0x120
+ /* Remove the MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 as not used */
+ >;
+};
+
+&iomuxc {
+ pinctrl_captouch: captouchgrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_SPDIF_RX_GPIO5_IO4 0x16
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3
+ MX8MN_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3
+ >;
+ };
+
+ pinctrl_pca9534: pca9534grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x16
+ >;
+ };
+
+ pinctrl_ptn5150: ptn5150grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x16
+ >;
+ };
+
+ pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_SAI2_RXC_GPIO4_IO22 0x41
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140
+ MX8MN_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140
+ MX8MN_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140
+ >;
+ };
+};
--
2.17.1
On Sat, Sep 19, 2020 at 04:13:30PM +0200, Krzysztof Kozlowski wrote:
> Add a binding for the Variscite Symphony evaluation kit board with
> VAR-SOM-MX8MN System on Module.
>
> Signed-off-by: Krzysztof Kozlowski <[email protected]>
> Reviewed-by: Rob Herring <[email protected]>
Applied all, thanks.