On Mon, Sep 21, 2020 at 12:35:16AM -0500, YiFei Zhu wrote:
> From: YiFei Zhu <[email protected]>
>
> This series adds a bitmap to cache seccomp filter results if the
> result permits a syscall and is indepenent of syscall arguments.
> This visibly decreases seccomp overhead for most common seccomp
> filters with very little memory footprint.
This is missing some people so expanding the Cc a little. Make sure to
run scripts/get_maintainers.pl next time, in case you forgot. (Adding
Andy, Will, Jann, Aleksa at least.)
Christian
>
> The overhead of running Seccomp filters has been part of some past
> discussions [1][2][3]. Oftentimes, the filters have a large number
> of instructions that check syscall numbers one by one and jump based
> on that. Some users chain BPF filters which further enlarge the
> overhead. A recent work [6] comprehensively measures the Seccomp
> overhead and shows that the overhead is non-negligible and has a
> non-trivial impact on application performance.
>
> We propose SECCOMP_CACHE, a cache-based solution to minimize the
> Seccomp overhead. The basic idea is to cache the result of each
> syscall check to save the subsequent overhead of executing the
> filters. This is feasible, because the check in Seccomp is stateless.
> The checking results of the same syscall ID and argument remains
> the same.
>
> We observed some common filters, such as docker's [4] or
> systemd's [5], will make most decisions based only on the syscall
> numbers, and as past discussions considered, a bitmap where each bit
> represents a syscall makes most sense for these filters.
>
> In the past Kees proposed [2] to have an "add this syscall to the
> reject bitmask". It is indeed much easier to securely make a reject
> accelerator to pre-filter syscalls before passing to the BPF
> filters, considering it could only strengthen the security provided
> by the filter. However, ultimately, filter rejections are an
> exceptional / rare case. Here, instead of accelerating what is
> rejected, we accelerate what is allowed. In order not to compromise
> the security rules the BPF filters defined, any accept-side
> accelerator must complement the BPF filters rather than replacing them.
>
> Statically analyzing BPF bytecode to see if each syscall is going to
> always land in allow or reject is more of a rabbit hole, especially
> there is no current in-kernel infrastructure to enumerate all the
> possible architecture numbers for a given machine. So rather than
> doing that, we propose to cache the results after the BPF filters are
> run. And since there are filters like docker's who will check
> arguments of some syscalls, but not all or none of the syscalls, when
> a filter is loaded we analyze it to find whether each syscall is
> cacheable (does not access syscall argument or instruction pointer) by
> following its control flow graph, and store the result for each filter
> in a bitmap. Changes to architecture number or the filter are expected
> to be rare and simply cause the cache to be cleared. This solution
> shall be fully transparent to userspace.
>
> Ongoing work is to further support arguments with fast hash table
> lookups. We are investigating the performance of doing so [6], and how
> to best integrate with the existing seccomp infrastructure.
>
> We have done some benchmarks with patch applied against bpf-next
> commit 2e80be60c465 ("libbpf: Fix compilation warnings for 64-bit printf args").
>
> Me, in qemu-kvm x86_64 VM, on Intel(R) Core(TM) i5-8250U CPU @ 1.60GHz,
> average results:
>
> Without cache, seccomp_benchmark:
> Current BPF sysctl settings:
> net.core.bpf_jit_enable = 1
> net.core.bpf_jit_harden = 0
> Calibrating sample size for 15 seconds worth of syscalls ...
> Benchmarking 23486415 syscalls...
> 16.079642020 - 1.013345439 = 15066296581 (15.1s)
> getpid native: 641 ns
> 32.080237410 - 16.080763500 = 15999473910 (16.0s)
> getpid RET_ALLOW 1 filter: 681 ns
> 48.609461618 - 32.081296173 = 16528165445 (16.5s)
> getpid RET_ALLOW 2 filters: 703 ns
> Estimated total seccomp overhead for 1 filter: 40 ns
> Estimated total seccomp overhead for 2 filters: 62 ns
> Estimated seccomp per-filter overhead: 22 ns
> Estimated seccomp entry overhead: 18 ns
>
> With cache:
> Current BPF sysctl settings:
> net.core.bpf_jit_enable = 1
> net.core.bpf_jit_harden = 0
> Calibrating sample size for 15 seconds worth of syscalls ...
> Benchmarking 23486415 syscalls...
> 16.059512499 - 1.014108434 = 15045404065 (15.0s)
> getpid native: 640 ns
> 31.651075934 - 16.060637323 = 15590438611 (15.6s)
> getpid RET_ALLOW 1 filter: 663 ns
> 47.367316169 - 31.652302661 = 15715013508 (15.7s)
> getpid RET_ALLOW 2 filters: 669 ns
> Estimated total seccomp overhead for 1 filter: 23 ns
> Estimated total seccomp overhead for 2 filters: 29 ns
> Estimated seccomp per-filter overhead: 6 ns
> Estimated seccomp entry overhead: 17 ns
>
> Depending on the run estimated seccomp overhead for 2 filters can be
> less than seccomp overhead for 1 filter, resulting in underflow to
> estimated seccomp per-filter overhead:
> Estimated total seccomp overhead for 1 filter: 27 ns
> Estimated total seccomp overhead for 2 filters: 21 ns
> Estimated seccomp per-filter overhead: 18446744073709551610 ns
> Estimated seccomp entry overhead: 33 ns
>
> Jack Chen has also run some benchmarks on a bare metal
> Intel(R) Xeon(R) CPU E3-1240 v3 @ 3.40GHz, with side channel
> mitigations off (spec_store_bypass_disable=off spectre_v2=off mds=off
> pti=off l1tf=off), with BPF JIT on and docker default profile,
> and reported:
>
> unixbench syscall mix (https://github.com/kdlucas/byte-unixbench)
> unconfined: 33295685
> docker default: 20661056 60%
> docker default + cache: 25719937 30%
>
> Patch 1 introduces the static analyzer to check for a given filter,
> whether the CFG loads the syscall arguments for each syscall number.
>
> Patch 2 implements the bitmap cache.
>
> [1] https://lore.kernel.org/linux-security-module/[email protected]/T/
> [2] https://lore.kernel.org/lkml/202005181120.971232B7B@keescook/T/
> [3] https://github.com/seccomp/libseccomp/issues/116
> [4] https://github.com/moby/moby/blob/ae0ef82b90356ac613f329a8ef5ee42ca923417d/profiles/seccomp/default.json
> [5] https://github.com/systemd/systemd/blob/6743a1caf4037f03dc51a1277855018e4ab61957/src/shared/seccomp-util.c#L270
> [6] Draco: Architectural and Operating System Support for System Call Security
> https://tianyin.github.io/pub/draco.pdf, MICRO-53, Oct. 2020
>
> YiFei Zhu (2):
> seccomp/cache: Add "emulator" to check if filter is arg-dependent
> seccomp/cache: Cache filter results that allow syscalls
>
> arch/x86/Kconfig | 27 +++
> include/linux/seccomp.h | 22 +++
> kernel/seccomp.c | 400 +++++++++++++++++++++++++++++++++++++++-
> 3 files changed, 446 insertions(+), 3 deletions(-)
>
> --
> 2.28.0
On Mon, Sep 21, 2020 at 3:30 AM Christian Brauner
<[email protected]> wrote:
> This is missing some people so expanding the Cc a little. Make sure to
> run scripts/get_maintainers.pl next time, in case you forgot. (Adding
> Andy, Will, Jann, Aleksa at least.)
>
> Christian
ok noted. Thanks!
YiFei Zhu