2020-10-01 15:16:14

by Frieder Schrempf

[permalink] [raw]
Subject: [PATCH v5 1/2] arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards

From: Frieder Schrempf <[email protected]>

Kontron Electronics GmbH offers small and powerful SoMs based on the
i.MX8M Mini SoC including PMIC, LPDDR4-RAM, eMMC and SPI NOR.

The matching baseboards have the same form factor and similar interfaces
as the other boards from the Kontron "Board-Line" family, including
SD card, 1G Ethernet, 100M Ethernet, USB Host/OTG, digital IOs, RS232,
RS485, CAN, LVDS or HDMI, RTC and much more.

Signed-off-by: Frieder Schrempf <[email protected]>
---
Changes for v5:
* Add Makefile entry to build dtb

Changes for v4:
* Remove one more needless status property
* Use local-mac-address instead of mac-address
* Add missing pinctrl-names in PMIC node
* Fix interrupt flags in PMIC node
* Use lowercase regulator names
* Enable pullup for PMIC IRQ line
* Fix pinctrl grp names to match schema

Changes for v3:
* Remove needless status properties
* Remove needless regulator properties for reg_vdd_5v
* Use proper PHY reset properties in PHY node
* Use phy-connection-type instead of phy-mode
* Adjust PMIC node name and label
* Add over-current-active-low to usbotg1 node
* Remove redundant bus-width property from usdhc2 node
* Remove needless regulator-compatible from reg_vdd_snvs
* Set minimum voltage to 85mV for reg_vdd_snvs

Changes for v2:
* Make the licensing less strict (GPL-2.0+ OR MIT)
* Merge the SoM and baseboard DTs for N8010 and N8011 into one as
they only differ in DDR and eMMC size.
* Change compatibles and model strings to "n810x" and "N8010X".
* Only use a common memory node that will be updated by the
bootloader reflecting the detected DDR size.
* Improve naming for 16MHz CAN fixed oscillator and set
"clock-output-names".
* Consistently use "reg_" prefix for regulators.
* Remove "userspi" node.
* Slightly improve commit message.
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../dts/freescale/imx8mm-kontron-n801x-s.dts | 322 ++++++++++++++++++
.../freescale/imx8mm-kontron-n801x-som.dtsi | 294 ++++++++++++++++
3 files changed, 617 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index f8d59433af01..e43254f1294d 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -31,6 +31,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-beacon-kit.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-n801x-s.dts
dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
new file mode 100644
index 000000000000..d17abb515835
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
@@ -0,0 +1,322 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2019 Kontron Electronics GmbH
+ */
+
+/dts-v1/;
+
+#include "imx8mm-kontron-n801x-som.dtsi"
+
+/ {
+ model = "Kontron i.MX8MM N801X S";
+ compatible = "kontron,imx8mm-n801x-s", "kontron,imx8mm-n801x-som", "fsl,imx8mm";
+
+ aliases {
+ ethernet1 = &usbnet;
+ };
+
+ /* fixed crystal dedicated to mcp2515 */
+ osc_can: clock-osc-can {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <16000000>;
+ clock-output-names = "osc-can";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_led>;
+
+ led1 {
+ label = "led1";
+ gpios = <&gpio4 17 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led2 {
+ label = "led2";
+ gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
+ };
+
+ led3 {
+ label = "led3";
+ gpios = <&gpio4 18 GPIO_ACTIVE_LOW>;
+ };
+
+ led4 {
+ label = "led4";
+ gpios = <&gpio4 8 GPIO_ACTIVE_LOW>;
+ };
+
+ led5 {
+ label = "led5";
+ gpios = <&gpio4 9 GPIO_ACTIVE_LOW>;
+ };
+
+ led6 {
+ label = "led6";
+ gpios = <&gpio4 7 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ pwm-beeper {
+ compatible = "pwm-beeper";
+ pwms = <&pwm2 0 5000 0>;
+ };
+
+ reg_rst_eth2: regulator-rst-eth2 {
+ compatible = "regulator-fixed";
+ regulator-name = "rst-usb-eth2";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_eth2>;
+ gpio = <&gpio3 2 GPIO_ACTIVE_LOW>;
+ };
+
+ reg_vdd_5v: regulator-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+};
+
+&ecspi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ can0: can@0 {
+ compatible = "microchip,mcp2515";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can>;
+ clocks = <&osc_can>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
+ spi-max-frequency = <100000>;
+ vdd-supply = <&reg_vdd_3v3>;
+ xceiver-supply = <&reg_vdd_5v>;
+ };
+};
+
+&ecspi3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3>;
+ cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-connection-type = "rgmii";
+ phy-handle = <&ethphy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy@0 {
+ reg = <0>;
+ reset-assert-us = <100>;
+ reset-deassert-us = <100>;
+ reset-gpios = <&gpio4 27 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&i2c4 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ status = "okay";
+
+ rtc@32 {
+ compatible = "epson,rx8900";
+ reg = <0x32>;
+ };
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ linux,rs485-enabled-at-boot-time;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&usbotg1 {
+ dr_mode = "otg";
+ over-current-active-low;
+ status = "okay";
+};
+
+&usbotg2 {
+ dr_mode = "host";
+ disable-over-current;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ usb1@1 {
+ compatible = "usb424,9514";
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usbnet: usbether@1 {
+ compatible = "usb424,ec00";
+ reg = <1>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ };
+ };
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ vmmc-supply = <&reg_vdd_3v3>;
+ vqmmc-supply = <&reg_nvcc_sd>;
+ cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio>;
+
+ pinctrl_can: cangrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28 0x19
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x82
+ MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x82
+ MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x82
+ MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x19
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_UART2_RXD_ECSPI3_MISO 0x82
+ MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI 0x82
+ MX8MM_IOMUXC_UART1_RXD_ECSPI3_SCLK 0x82
+ MX8MM_IOMUXC_UART2_TXD_GPIO5_IO25 0x19
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3
+ MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3
+ MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
+ MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
+ MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
+ MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
+ MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
+ MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
+ MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
+ MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
+ MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
+ MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
+ MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
+ MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
+ MX8MM_IOMUXC_SAI2_MCLK_GPIO4_IO27 0x19 /* PHY RST */
+ MX8MM_IOMUXC_SAI2_TXC_GPIO4_IO25 0x19 /* ETH IRQ */
+ >;
+ };
+
+ pinctrl_gpio_led: gpioledgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x19
+ MX8MM_IOMUXC_SAI1_RXD5_GPIO4_IO7 0x19
+ MX8MM_IOMUXC_SAI1_RXD6_GPIO4_IO8 0x19
+ MX8MM_IOMUXC_SAI1_RXD7_GPIO4_IO9 0x19
+ MX8MM_IOMUXC_SAI1_TXD5_GPIO4_IO17 0x19
+ MX8MM_IOMUXC_SAI1_TXD6_GPIO4_IO18 0x19
+ MX8MM_IOMUXC_SAI1_TXD7_GPIO4_IO19 0x19
+ >;
+ };
+
+ pinctrl_gpio: gpiogrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x19
+ MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x19
+ MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19
+ MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x19
+ MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x19
+ MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x19
+ MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x19
+ MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2 0x19
+ >;
+ };
+
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x400001c3
+ MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA 0x400001c3
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT 0x19
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX 0x140
+ MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX 0x140
+ MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B 0x140
+ MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B 0x140
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX 0x140
+ MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX 0x140
+ MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x140
+ MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x140
+ >;
+ };
+
+ pinctrl_usb_eth2: usbeth2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2 0x19
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
+ MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x019
+ >;
+ };
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
new file mode 100644
index 000000000000..d0456daefda8
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
@@ -0,0 +1,294 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2019 Kontron Electronics GmbH
+ */
+
+#include "imx8mm.dtsi"
+
+/ {
+ model = "Kontron i.MX8MM N801X SoM";
+ compatible = "kontron,imx8mm-n801x-som", "fsl,imx8mm";
+
+ memory@40000000 {
+ device_type = "memory";
+ /*
+ * There are multiple SoM flavors with different DDR sizes.
+ * The smallest is 1GB. For larger sizes the bootloader will
+ * update the reg property.
+ */
+ reg = <0x0 0x40000000 0 0x80000000>;
+ };
+
+ chosen {
+ stdout-path = &uart3;
+ };
+};
+
+&A53_0 {
+ cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_1 {
+ cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_2 {
+ cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_3 {
+ cpu-supply = <&reg_vdd_arm>;
+};
+
+&ddrc {
+ operating-points-v2 = <&ddrc_opp_table>;
+
+ ddrc_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-25M {
+ opp-hz = /bits/ 64 <25000000>;
+ };
+
+ opp-100M {
+ opp-hz = /bits/ 64 <100000000>;
+ };
+
+ opp-750M {
+ opp-hz = /bits/ 64 <750000000>;
+ };
+ };
+};
+
+&ecspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ cs-gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ spi-flash@0 {
+ compatible = "mxicy,mx25r1635f", "jedec,spi-nor";
+ spi-max-frequency = <80000000>;
+ reg = <0>;
+ };
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ pca9450: pmic@25 {
+ compatible = "nxp,pca9450a";
+ reg = <0x25>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pmic>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ reg_vdd_soc: BUCK1 {
+ regulator-name = "buck1";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <3125>;
+ };
+
+ reg_vdd_arm: BUCK2 {
+ regulator-name = "buck2";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <950000>;
+ regulator-boot-on;
+ regulator-ramp-delay = <3125>;
+ nxp,dvs-run-voltage = <950000>;
+ nxp,dvs-standby-voltage = <850000>;
+ };
+
+ reg_vdd_dram: BUCK3 {
+ regulator-name = "buck3";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_vdd_3v3: BUCK4 {
+ regulator-name = "buck4";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_vdd_1v8: BUCK5 {
+ regulator-name = "buck5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_nvcc_dram: BUCK6 {
+ regulator-name = "buck6";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_nvcc_snvs: LDO1 {
+ regulator-name = "ldo1";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_vdd_snvs: LDO2 {
+ regulator-name = "ldo2";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_vdda: LDO3 {
+ regulator-name = "ldo3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_vdd_phy: LDO4 {
+ regulator-name = "ldo4";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_nvcc_sd: LDO5 {
+ regulator-name = "ldo5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+ };
+};
+
+&uart3 { /* console */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ vmmc-supply = <&reg_vdd_3v3>;
+ vqmmc-supply = <&reg_vdd_1v8>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x82
+ MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x82
+ MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x82
+ MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x19
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3
+ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3
+ >;
+ };
+
+ pinctrl_pmic: pmicgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x141
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140
+ MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190
+ MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0
+ MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0
+ MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0
+ MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0
+ MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0
+ MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d0
+ MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d0
+ MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d0
+ MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d0
+ MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x019
+ MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x190
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x194
+ MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4
+ MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4
+ MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4
+ MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4
+ MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4
+ MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d4
+ MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d4
+ MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d4
+ MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d4
+ MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x019
+ MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x194
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x196
+ MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6
+ MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6
+ MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6
+ MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6
+ MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6
+ MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d6
+ MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d6
+ MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d6
+ MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d6
+ MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x019
+ MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x196
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
+ >;
+ };
+};
--
2.17.1


2020-10-01 15:19:03

by Frieder Schrempf

[permalink] [raw]
Subject: [PATCH v5 2/2] dt-bindings: arm: fsl: Add Kontron i.MX8M Mini SoMs and boards

From: Frieder Schrempf <[email protected]>

Add entries for the SoMs and boards based on i.MX8MM from Kontron
Electronics GmbH.

Signed-off-by: Frieder Schrempf <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
---
Changes for v5:
* None

Changes for v4:
* Rebase on next-20201001
* Enhance SoM and board description

Changes for v3:
* None

Changes for v2:
* Merge the SoMs and baseboards N8010 and N8011 into a single
configuration (N801X).
* Add Rob's R-b tag
---
Documentation/devicetree/bindings/arm/fsl.yaml | 7 +++++++
1 file changed, 7 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 1ca9dfa8ce9a..6daf4c046785 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -405,9 +405,16 @@ properties:
- beacon,imx8mm-beacon-kit # i.MX8MM Beacon Development Kit
- fsl,imx8mm-ddr4-evk # i.MX8MM DDR4 EVK Board
- fsl,imx8mm-evk # i.MX8MM EVK Board
+ - kontron,imx8mm-n801x-som # i.MX8MM Kontron SL (N801X) SOM
- variscite,var-som-mx8mm # i.MX8MM Variscite VAR-SOM-MX8MM module
- const: fsl,imx8mm

+ - description: Kontron BL i.MX8MM (N801X S) Board
+ items:
+ - const: kontron,imx8mm-n801x-s
+ - const: kontron,imx8mm-n801x-som
+ - const: fsl,imx8mm
+
- description: Variscite VAR-SOM-MX8MM based boards
items:
- const: variscite,var-som-mx8mm-symphony
--
2.17.1

2020-10-01 15:21:41

by Krzysztof Kozlowski

[permalink] [raw]
Subject: Re: [PATCH v5 2/2] dt-bindings: arm: fsl: Add Kontron i.MX8M Mini SoMs and boards

On Thu, Oct 01, 2020 at 05:13:38PM +0200, Schrempf Frieder wrote:
> From: Frieder Schrempf <[email protected]>
>
> Add entries for the SoMs and boards based on i.MX8MM from Kontron
> Electronics GmbH.
>
> Signed-off-by: Frieder Schrempf <[email protected]>
> Reviewed-by: Rob Herring <[email protected]>
> ---
> Changes for v5:
> * None
>
> Changes for v4:
> * Rebase on next-20201001
> * Enhance SoM and board description
>
> Changes for v3:
> * None
>
> Changes for v2:
> * Merge the SoMs and baseboards N8010 and N8011 into a single
> configuration (N801X).
> * Add Rob's R-b tag
> ---
> Documentation/devicetree/bindings/arm/fsl.yaml | 7 +++++++
> 1 file changed, 7 insertions(+)

Reviewed-by: Krzysztof Kozlowski <[email protected]>

Best regards,
Krzysztof

2020-10-01 15:23:16

by Krzysztof Kozlowski

[permalink] [raw]
Subject: Re: [PATCH v5 1/2] arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards

On Thu, Oct 01, 2020 at 05:13:37PM +0200, Schrempf Frieder wrote:
> From: Frieder Schrempf <[email protected]>
>
> Kontron Electronics GmbH offers small and powerful SoMs based on the
> i.MX8M Mini SoC including PMIC, LPDDR4-RAM, eMMC and SPI NOR.
>
> The matching baseboards have the same form factor and similar interfaces
> as the other boards from the Kontron "Board-Line" family, including
> SD card, 1G Ethernet, 100M Ethernet, USB Host/OTG, digital IOs, RS232,
> RS485, CAN, LVDS or HDMI, RTC and much more.
>
> Signed-off-by: Frieder Schrempf <[email protected]>
> ---
> Changes for v5:
> * Add Makefile entry to build dtb
>
> Changes for v4:
> * Remove one more needless status property
> * Use local-mac-address instead of mac-address
> * Add missing pinctrl-names in PMIC node
> * Fix interrupt flags in PMIC node
> * Use lowercase regulator names
> * Enable pullup for PMIC IRQ line
> * Fix pinctrl grp names to match schema
>
> Changes for v3:
> * Remove needless status properties
> * Remove needless regulator properties for reg_vdd_5v
> * Use proper PHY reset properties in PHY node
> * Use phy-connection-type instead of phy-mode
> * Adjust PMIC node name and label
> * Add over-current-active-low to usbotg1 node
> * Remove redundant bus-width property from usdhc2 node
> * Remove needless regulator-compatible from reg_vdd_snvs
> * Set minimum voltage to 85mV for reg_vdd_snvs
>
> Changes for v2:
> * Make the licensing less strict (GPL-2.0+ OR MIT)
> * Merge the SoM and baseboard DTs for N8010 and N8011 into one as
> they only differ in DDR and eMMC size.
> * Change compatibles and model strings to "n810x" and "N8010X".
> * Only use a common memory node that will be updated by the
> bootloader reflecting the detected DDR size.
> * Improve naming for 16MHz CAN fixed oscillator and set
> "clock-output-names".
> * Consistently use "reg_" prefix for regulators.
> * Remove "userspi" node.
> * Slightly improve commit message.
> ---
> arch/arm64/boot/dts/freescale/Makefile | 1 +
> .../dts/freescale/imx8mm-kontron-n801x-s.dts | 322 ++++++++++++++++++
> .../freescale/imx8mm-kontron-n801x-som.dtsi | 294 ++++++++++++++++
> 3 files changed, 617 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile

Reviewed-by: Krzysztof Kozlowski <[email protected]>

Best regards,
Krzysztof

2020-10-30 07:05:41

by Shawn Guo

[permalink] [raw]
Subject: Re: [PATCH v5 1/2] arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards

On Thu, Oct 01, 2020 at 05:13:37PM +0200, Schrempf Frieder wrote:
> From: Frieder Schrempf <[email protected]>
>
> Kontron Electronics GmbH offers small and powerful SoMs based on the
> i.MX8M Mini SoC including PMIC, LPDDR4-RAM, eMMC and SPI NOR.
>
> The matching baseboards have the same form factor and similar interfaces
> as the other boards from the Kontron "Board-Line" family, including
> SD card, 1G Ethernet, 100M Ethernet, USB Host/OTG, digital IOs, RS232,
> RS485, CAN, LVDS or HDMI, RTC and much more.
>
> Signed-off-by: Frieder Schrempf <[email protected]>

Applied both, thanks.