TCPM at present lacks the notion of VSAFE0V. There
are three vbus threshold levels that are critical to track:
a. vSafe5V - VBUS “5 volts” as defined by the USB
PD specification.
b. vSinkDisconnect - Threshold used for transition from
Attached.SNK to Unattached.SNK.
c. vSafe0V - VBUS “0 volts” as defined by the USB
PD specification.
Tracking vSafe0V is crucial for entry into Try.SNK and
Attached.SRC and turning vbus back on by the source in
response to hard reset.
From "4.5.2.2.8.2 Exiting from AttachWait.SRC State" section
in the Type-C spec:
"The port shall transition to Attached.SRC when VBUS is at
vSafe0V and the SRC.Rd state is detected on exactly one of
the CC1 or CC2 pins for at least tCCDebounce."
"A DRP that strongly prefers the Sink role may optionally
transition to Try.SNK instead of Attached.SRC when VBUS
is at vSafe0V and the SRC.Rd state is detected on exactly
one of the CC1 or CC2 pins for at least tCCDebounce."
From "7.1.5 Response to Hard Resets" section in the PD spec:
"After establishing the vSafe0V voltage condition on VBUS,
the Source Shall wait tSrcRecover before re-applying VCONN
and restoring VBUS to vSafe5V."
vbus_present in the TCPM code tracks vSafe5V(vbus_present is true)
and vSinkDisconnect(vbus_present is false).
This change adds is_vbus_vsafe0v callback which when set makes
TCPM query for vSafe0V voltage level when needed.
Since not all TCPC controllers might have the capability
to report vSafe0V, TCPM assumes that vSafe0V is same as
vSinkDisconnect when is_vbus_vsafe0v callback is not set.
This allows TCPM to continue to support controllers which don't
have the support for reporting vSafe0V.
Introducing vSafe0V helps fix the failure reported at
"Step 15. CVS verifies PUT remains in AttachWait.SRC for 500ms"
of "TD 4.7.2 Try. SNK DRP Connect DRP Test" of
"Universal Serial Bus Type-C (USB Type-C) Functional Test
Specification Chapters 4 and 5". Here the compliance tester
intentionally maintains vbus at greater than vSafe0V and expects
the Product under test to stay in AttachWait.SRC till vbus drops
to vSafe0V.
Signed-off-by: Badhri Jagan Sridharan <[email protected]>
---
Changes since v1:
- Changed return type to bool instead of int for
is_vbus_vsafe0v as suggested by Guenter and updated
the documentation.
---
drivers/usb/typec/tcpm/tcpm.c | 63 +++++++++++++++++++++++++++++------
include/linux/usb/tcpm.h | 7 ++++
2 files changed, 59 insertions(+), 11 deletions(-)
diff --git a/drivers/usb/typec/tcpm/tcpm.c b/drivers/usb/typec/tcpm/tcpm.c
index 3bbc1f10af49..4cd6e0196f94 100644
--- a/drivers/usb/typec/tcpm/tcpm.c
+++ b/drivers/usb/typec/tcpm/tcpm.c
@@ -258,7 +258,19 @@ struct tcpm_port {
bool attached;
bool connected;
enum typec_port_type port_type;
+
+ /*
+ * Set to true when vbus is greater than VSAFE5V min.
+ * Set to false when vbus falls below vSinkDisconnect max threshold.
+ */
bool vbus_present;
+
+ /*
+ * Set to true when vbus is less than VSAFE0V max.
+ * Set to false when vbus is greater than VSAFE0V max.
+ */
+ bool vbus_vsafe0v;
+
bool vbus_never_low;
bool vbus_source;
bool vbus_charge;
@@ -3094,7 +3106,7 @@ static void run_state_machine(struct tcpm_port *port)
else if (tcpm_port_is_audio(port))
tcpm_set_state(port, AUDIO_ACC_ATTACHED,
PD_T_CC_DEBOUNCE);
- else if (tcpm_port_is_source(port))
+ else if (tcpm_port_is_source(port) && port->vbus_vsafe0v)
tcpm_set_state(port,
tcpm_try_snk(port) ? SNK_TRY
: SRC_ATTACHED,
@@ -4097,6 +4109,12 @@ static void _tcpm_pd_vbus_on(struct tcpm_port *port)
{
tcpm_log_force(port, "VBUS on");
port->vbus_present = true;
+ /*
+ * When vbus_present is true i.e. Voltage at VBUS is greater than VSAFE5V implicitly
+ * states that vbus is not at VSAFE0V, hence clear the vbus_vsafe0v flag here.
+ */
+ port->vbus_vsafe0v = false;
+
switch (port->state) {
case SNK_TRANSITION_SINK_VBUS:
port->explicit_contract = true;
@@ -4186,16 +4204,8 @@ static void _tcpm_pd_vbus_off(struct tcpm_port *port)
case SNK_HARD_RESET_SINK_OFF:
tcpm_set_state(port, SNK_HARD_RESET_WAIT_VBUS, 0);
break;
- case SRC_HARD_RESET_VBUS_OFF:
- /*
- * After establishing the vSafe0V voltage condition on VBUS, the Source Shall wait
- * tSrcRecover before re-applying VCONN and restoring VBUS to vSafe5V.
- */
- tcpm_set_state(port, SRC_HARD_RESET_VBUS_ON, PD_T_SRC_RECOVER);
- break;
case HARD_RESET_SEND:
break;
-
case SNK_TRY:
/* Do nothing, waiting for timeout */
break;
@@ -4266,6 +4276,28 @@ static void _tcpm_pd_vbus_off(struct tcpm_port *port)
}
}
+static void _tcpm_pd_vbus_vsafe0v(struct tcpm_port *port)
+{
+ tcpm_log_force(port, "VBUS VSAFE0V");
+ port->vbus_vsafe0v = true;
+ switch (port->state) {
+ case SRC_HARD_RESET_VBUS_OFF:
+ /*
+ * After establishing the vSafe0V voltage condition on VBUS, the Source Shall wait
+ * tSrcRecover before re-applying VCONN and restoring VBUS to vSafe5V.
+ */
+ tcpm_set_state(port, SRC_HARD_RESET_VBUS_ON, PD_T_SRC_RECOVER);
+ break;
+ case SRC_ATTACH_WAIT:
+ if (tcpm_port_is_source(port))
+ tcpm_set_state(port, tcpm_try_snk(port) ? SNK_TRY : SRC_ATTACHED,
+ PD_T_CC_DEBOUNCE);
+ break;
+ default:
+ break;
+ }
+}
+
static void _tcpm_pd_hard_reset(struct tcpm_port *port)
{
tcpm_log_force(port, "Received hard reset");
@@ -4301,10 +4333,19 @@ static void tcpm_pd_event_handler(struct kthread_work *work)
bool vbus;
vbus = port->tcpc->get_vbus(port->tcpc);
- if (vbus)
+ if (vbus) {
_tcpm_pd_vbus_on(port);
- else
+ } else {
_tcpm_pd_vbus_off(port);
+ /*
+ * When TCPC does not support detecting vsafe0v voltage level,
+ * treat vbus absent as vsafe0v. Else invoke is_vbus_vsafe0v
+ * to see if vbus has discharge to VSAFE0V.
+ */
+ if (!port->tcpc->is_vbus_vsafe0v ||
+ port->tcpc->is_vbus_vsafe0v(port->tcpc))
+ _tcpm_pd_vbus_vsafe0v(port);
+ }
}
if (events & TCPM_CC_EVENT) {
enum typec_cc_status cc1, cc2;
diff --git a/include/linux/usb/tcpm.h b/include/linux/usb/tcpm.h
index e68aaa12886f..3e39874cfac4 100644
--- a/include/linux/usb/tcpm.h
+++ b/include/linux/usb/tcpm.h
@@ -98,6 +98,12 @@ enum tcpm_transmit_type {
* will be turned on. requested_vbus_voltage is set to 0 when vbus
* is going to disappear knowingly i.e. during PR_SWAP and
* HARD_RESET etc.
+ * @is_vbus_vsafe0v:
+ * Optional; TCPCI spec based TCPC implementations are expected to
+ * detect VSAFE0V voltage level at vbus. When detection of VSAFE0V
+ * is supported by TCPC, set this callback for TCPM to query
+ * whether vbus is at VSAFE0V when needed.
+ * Returns true when vbus is at VSAFE0V, false otherwise.
*/
struct tcpc_dev {
struct fwnode_handle *fwnode;
@@ -128,6 +134,7 @@ struct tcpc_dev {
int (*enable_auto_vbus_discharge)(struct tcpc_dev *dev, bool enable);
int (*set_auto_vbus_discharge_threshold)(struct tcpc_dev *dev, enum typec_pwr_opmode mode,
bool pps_active, u32 requested_vbus_voltage);
+ bool (*is_vbus_vsafe0v)(struct tcpc_dev *dev);
};
struct tcpm_port;
--
2.29.2.576.ga3fc446d84-goog
Unmask EXTENDED_STATUS_MASK.vSafe0V, ALERT.Extended_Status
and set vbus_vsafe0v to enable VSAFE0V signalling.
Signed-off-by: Badhri Jagan Sridharan <[email protected]>
---
Changes since v1:
- Setting auto_discharge_disconnect to true instead of 1 as
suggested by Guenter.
---
drivers/usb/typec/tcpm/tcpci_maxim.c | 16 +++++++++++++++-
1 file changed, 15 insertions(+), 1 deletion(-)
diff --git a/drivers/usb/typec/tcpm/tcpci_maxim.c b/drivers/usb/typec/tcpm/tcpci_maxim.c
index c1797239bf08..319266329b42 100644
--- a/drivers/usb/typec/tcpm/tcpci_maxim.c
+++ b/drivers/usb/typec/tcpm/tcpci_maxim.c
@@ -112,11 +112,18 @@ static void max_tcpci_init_regs(struct max_tcpci_chip *chip)
return;
}
+ /* Enable VSAFE0V detection */
+ ret = max_tcpci_write8(chip, TCPC_EXTENDED_STATUS_MASK, TCPC_EXTENDED_STATUS_VSAFE0V);
+ if (ret < 0) {
+ dev_err(chip->dev, "Unable to unmask TCPC_EXTENDED_STATUS_VSAFE0V ret:%d\n", ret);
+ return;
+ }
+
alert_mask = TCPC_ALERT_TX_SUCCESS | TCPC_ALERT_TX_DISCARDED | TCPC_ALERT_TX_FAILED |
TCPC_ALERT_RX_HARD_RST | TCPC_ALERT_RX_STATUS | TCPC_ALERT_CC_STATUS |
TCPC_ALERT_VBUS_DISCNCT | TCPC_ALERT_RX_BUF_OVF | TCPC_ALERT_POWER_STATUS |
/* Enable Extended alert for detecting Fast Role Swap Signal */
- TCPC_ALERT_EXTND;
+ TCPC_ALERT_EXTND | TCPC_ALERT_EXTENDED_STATUS;
ret = max_tcpci_write16(chip, TCPC_ALERT_MASK, alert_mask);
if (ret < 0) {
@@ -315,6 +322,12 @@ static irqreturn_t _max_tcpci_irq(struct max_tcpci_chip *chip, u16 status)
}
}
+ if (status & TCPC_ALERT_EXTENDED_STATUS) {
+ ret = max_tcpci_read8(chip, TCPC_EXTENDED_STATUS, (u8 *)®_status);
+ if (ret >= 0 && (reg_status & TCPC_EXTENDED_STATUS_VSAFE0V))
+ tcpm_vbus_change(chip->port);
+ }
+
if (status & TCPC_ALERT_RX_STATUS)
process_rx(chip, status);
@@ -442,6 +455,7 @@ static int max_tcpci_probe(struct i2c_client *client, const struct i2c_device_id
chip->data.init = tcpci_init;
chip->data.frs_sourcing_vbus = max_tcpci_frs_sourcing_vbus;
chip->data.auto_discharge_disconnect = true;
+ chip->data.vbus_vsafe0v = true;
max_tcpci_init_regs(chip);
chip->tcpci = tcpci_register_port(chip->dev, &chip->data);
--
2.29.2.576.ga3fc446d84-goog
On Tue, Dec 01, 2020 at 08:08:40PM -0800, Badhri Jagan Sridharan wrote:
> Unmask EXTENDED_STATUS_MASK.vSafe0V, ALERT.Extended_Status
> and set vbus_vsafe0v to enable VSAFE0V signalling.
>
> Signed-off-by: Badhri Jagan Sridharan <[email protected]>
Acked-by: Heikki Krogerus <[email protected]>
> ---
> Changes since v1:
> - Setting auto_discharge_disconnect to true instead of 1 as
> suggested by Guenter.
> ---
> drivers/usb/typec/tcpm/tcpci_maxim.c | 16 +++++++++++++++-
> 1 file changed, 15 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/usb/typec/tcpm/tcpci_maxim.c b/drivers/usb/typec/tcpm/tcpci_maxim.c
> index c1797239bf08..319266329b42 100644
> --- a/drivers/usb/typec/tcpm/tcpci_maxim.c
> +++ b/drivers/usb/typec/tcpm/tcpci_maxim.c
> @@ -112,11 +112,18 @@ static void max_tcpci_init_regs(struct max_tcpci_chip *chip)
> return;
> }
>
> + /* Enable VSAFE0V detection */
> + ret = max_tcpci_write8(chip, TCPC_EXTENDED_STATUS_MASK, TCPC_EXTENDED_STATUS_VSAFE0V);
> + if (ret < 0) {
> + dev_err(chip->dev, "Unable to unmask TCPC_EXTENDED_STATUS_VSAFE0V ret:%d\n", ret);
> + return;
> + }
> +
> alert_mask = TCPC_ALERT_TX_SUCCESS | TCPC_ALERT_TX_DISCARDED | TCPC_ALERT_TX_FAILED |
> TCPC_ALERT_RX_HARD_RST | TCPC_ALERT_RX_STATUS | TCPC_ALERT_CC_STATUS |
> TCPC_ALERT_VBUS_DISCNCT | TCPC_ALERT_RX_BUF_OVF | TCPC_ALERT_POWER_STATUS |
> /* Enable Extended alert for detecting Fast Role Swap Signal */
> - TCPC_ALERT_EXTND;
> + TCPC_ALERT_EXTND | TCPC_ALERT_EXTENDED_STATUS;
>
> ret = max_tcpci_write16(chip, TCPC_ALERT_MASK, alert_mask);
> if (ret < 0) {
> @@ -315,6 +322,12 @@ static irqreturn_t _max_tcpci_irq(struct max_tcpci_chip *chip, u16 status)
> }
> }
>
> + if (status & TCPC_ALERT_EXTENDED_STATUS) {
> + ret = max_tcpci_read8(chip, TCPC_EXTENDED_STATUS, (u8 *)®_status);
> + if (ret >= 0 && (reg_status & TCPC_EXTENDED_STATUS_VSAFE0V))
> + tcpm_vbus_change(chip->port);
> + }
> +
> if (status & TCPC_ALERT_RX_STATUS)
> process_rx(chip, status);
>
> @@ -442,6 +455,7 @@ static int max_tcpci_probe(struct i2c_client *client, const struct i2c_device_id
> chip->data.init = tcpci_init;
> chip->data.frs_sourcing_vbus = max_tcpci_frs_sourcing_vbus;
> chip->data.auto_discharge_disconnect = true;
> + chip->data.vbus_vsafe0v = true;
>
> max_tcpci_init_regs(chip);
> chip->tcpci = tcpci_register_port(chip->dev, &chip->data);
> --
> 2.29.2.576.ga3fc446d84-goog
--
heikki
On Tue, Dec 01, 2020 at 08:08:38PM -0800, Badhri Jagan Sridharan wrote:
> TCPM at present lacks the notion of VSAFE0V. There
> are three vbus threshold levels that are critical to track:
> a. vSafe5V - VBUS “5 volts” as defined by the USB
> PD specification.
> b. vSinkDisconnect - Threshold used for transition from
> Attached.SNK to Unattached.SNK.
> c. vSafe0V - VBUS “0 volts” as defined by the USB
> PD specification.
>
> Tracking vSafe0V is crucial for entry into Try.SNK and
> Attached.SRC and turning vbus back on by the source in
> response to hard reset.
>
> >From "4.5.2.2.8.2 Exiting from AttachWait.SRC State" section
> in the Type-C spec:
>
> "The port shall transition to Attached.SRC when VBUS is at
> vSafe0V and the SRC.Rd state is detected on exactly one of
> the CC1 or CC2 pins for at least tCCDebounce."
>
> "A DRP that strongly prefers the Sink role may optionally
> transition to Try.SNK instead of Attached.SRC when VBUS
> is at vSafe0V and the SRC.Rd state is detected on exactly
> one of the CC1 or CC2 pins for at least tCCDebounce."
>
> >From "7.1.5 Response to Hard Resets" section in the PD spec:
>
> "After establishing the vSafe0V voltage condition on VBUS,
> the Source Shall wait tSrcRecover before re-applying VCONN
> and restoring VBUS to vSafe5V."
>
> vbus_present in the TCPM code tracks vSafe5V(vbus_present is true)
> and vSinkDisconnect(vbus_present is false).
>
> This change adds is_vbus_vsafe0v callback which when set makes
> TCPM query for vSafe0V voltage level when needed.
>
> Since not all TCPC controllers might have the capability
> to report vSafe0V, TCPM assumes that vSafe0V is same as
> vSinkDisconnect when is_vbus_vsafe0v callback is not set.
> This allows TCPM to continue to support controllers which don't
> have the support for reporting vSafe0V.
>
> Introducing vSafe0V helps fix the failure reported at
> "Step 15. CVS verifies PUT remains in AttachWait.SRC for 500ms"
> of "TD 4.7.2 Try. SNK DRP Connect DRP Test" of
> "Universal Serial Bus Type-C (USB Type-C) Functional Test
> Specification Chapters 4 and 5". Here the compliance tester
> intentionally maintains vbus at greater than vSafe0V and expects
> the Product under test to stay in AttachWait.SRC till vbus drops
> to vSafe0V.
>
> Signed-off-by: Badhri Jagan Sridharan <[email protected]>
Guenter really should check these, but FWIW:
Acked-by: Heikki Krogerus <[email protected]>
> ---
> Changes since v1:
> - Changed return type to bool instead of int for
> is_vbus_vsafe0v as suggested by Guenter and updated
> the documentation.
> ---
> drivers/usb/typec/tcpm/tcpm.c | 63 +++++++++++++++++++++++++++++------
> include/linux/usb/tcpm.h | 7 ++++
> 2 files changed, 59 insertions(+), 11 deletions(-)
>
> diff --git a/drivers/usb/typec/tcpm/tcpm.c b/drivers/usb/typec/tcpm/tcpm.c
> index 3bbc1f10af49..4cd6e0196f94 100644
> --- a/drivers/usb/typec/tcpm/tcpm.c
> +++ b/drivers/usb/typec/tcpm/tcpm.c
> @@ -258,7 +258,19 @@ struct tcpm_port {
> bool attached;
> bool connected;
> enum typec_port_type port_type;
> +
> + /*
> + * Set to true when vbus is greater than VSAFE5V min.
> + * Set to false when vbus falls below vSinkDisconnect max threshold.
> + */
> bool vbus_present;
> +
> + /*
> + * Set to true when vbus is less than VSAFE0V max.
> + * Set to false when vbus is greater than VSAFE0V max.
> + */
> + bool vbus_vsafe0v;
> +
> bool vbus_never_low;
> bool vbus_source;
> bool vbus_charge;
> @@ -3094,7 +3106,7 @@ static void run_state_machine(struct tcpm_port *port)
> else if (tcpm_port_is_audio(port))
> tcpm_set_state(port, AUDIO_ACC_ATTACHED,
> PD_T_CC_DEBOUNCE);
> - else if (tcpm_port_is_source(port))
> + else if (tcpm_port_is_source(port) && port->vbus_vsafe0v)
> tcpm_set_state(port,
> tcpm_try_snk(port) ? SNK_TRY
> : SRC_ATTACHED,
> @@ -4097,6 +4109,12 @@ static void _tcpm_pd_vbus_on(struct tcpm_port *port)
> {
> tcpm_log_force(port, "VBUS on");
> port->vbus_present = true;
> + /*
> + * When vbus_present is true i.e. Voltage at VBUS is greater than VSAFE5V implicitly
> + * states that vbus is not at VSAFE0V, hence clear the vbus_vsafe0v flag here.
> + */
> + port->vbus_vsafe0v = false;
> +
> switch (port->state) {
> case SNK_TRANSITION_SINK_VBUS:
> port->explicit_contract = true;
> @@ -4186,16 +4204,8 @@ static void _tcpm_pd_vbus_off(struct tcpm_port *port)
> case SNK_HARD_RESET_SINK_OFF:
> tcpm_set_state(port, SNK_HARD_RESET_WAIT_VBUS, 0);
> break;
> - case SRC_HARD_RESET_VBUS_OFF:
> - /*
> - * After establishing the vSafe0V voltage condition on VBUS, the Source Shall wait
> - * tSrcRecover before re-applying VCONN and restoring VBUS to vSafe5V.
> - */
> - tcpm_set_state(port, SRC_HARD_RESET_VBUS_ON, PD_T_SRC_RECOVER);
> - break;
> case HARD_RESET_SEND:
> break;
> -
> case SNK_TRY:
> /* Do nothing, waiting for timeout */
> break;
> @@ -4266,6 +4276,28 @@ static void _tcpm_pd_vbus_off(struct tcpm_port *port)
> }
> }
>
> +static void _tcpm_pd_vbus_vsafe0v(struct tcpm_port *port)
> +{
> + tcpm_log_force(port, "VBUS VSAFE0V");
> + port->vbus_vsafe0v = true;
> + switch (port->state) {
> + case SRC_HARD_RESET_VBUS_OFF:
> + /*
> + * After establishing the vSafe0V voltage condition on VBUS, the Source Shall wait
> + * tSrcRecover before re-applying VCONN and restoring VBUS to vSafe5V.
> + */
> + tcpm_set_state(port, SRC_HARD_RESET_VBUS_ON, PD_T_SRC_RECOVER);
> + break;
> + case SRC_ATTACH_WAIT:
> + if (tcpm_port_is_source(port))
> + tcpm_set_state(port, tcpm_try_snk(port) ? SNK_TRY : SRC_ATTACHED,
> + PD_T_CC_DEBOUNCE);
> + break;
> + default:
> + break;
> + }
> +}
> +
> static void _tcpm_pd_hard_reset(struct tcpm_port *port)
> {
> tcpm_log_force(port, "Received hard reset");
> @@ -4301,10 +4333,19 @@ static void tcpm_pd_event_handler(struct kthread_work *work)
> bool vbus;
>
> vbus = port->tcpc->get_vbus(port->tcpc);
> - if (vbus)
> + if (vbus) {
> _tcpm_pd_vbus_on(port);
> - else
> + } else {
> _tcpm_pd_vbus_off(port);
> + /*
> + * When TCPC does not support detecting vsafe0v voltage level,
> + * treat vbus absent as vsafe0v. Else invoke is_vbus_vsafe0v
> + * to see if vbus has discharge to VSAFE0V.
> + */
> + if (!port->tcpc->is_vbus_vsafe0v ||
> + port->tcpc->is_vbus_vsafe0v(port->tcpc))
> + _tcpm_pd_vbus_vsafe0v(port);
> + }
> }
> if (events & TCPM_CC_EVENT) {
> enum typec_cc_status cc1, cc2;
> diff --git a/include/linux/usb/tcpm.h b/include/linux/usb/tcpm.h
> index e68aaa12886f..3e39874cfac4 100644
> --- a/include/linux/usb/tcpm.h
> +++ b/include/linux/usb/tcpm.h
> @@ -98,6 +98,12 @@ enum tcpm_transmit_type {
> * will be turned on. requested_vbus_voltage is set to 0 when vbus
> * is going to disappear knowingly i.e. during PR_SWAP and
> * HARD_RESET etc.
> + * @is_vbus_vsafe0v:
> + * Optional; TCPCI spec based TCPC implementations are expected to
> + * detect VSAFE0V voltage level at vbus. When detection of VSAFE0V
> + * is supported by TCPC, set this callback for TCPM to query
> + * whether vbus is at VSAFE0V when needed.
> + * Returns true when vbus is at VSAFE0V, false otherwise.
> */
> struct tcpc_dev {
> struct fwnode_handle *fwnode;
> @@ -128,6 +134,7 @@ struct tcpc_dev {
> int (*enable_auto_vbus_discharge)(struct tcpc_dev *dev, bool enable);
> int (*set_auto_vbus_discharge_threshold)(struct tcpc_dev *dev, enum typec_pwr_opmode mode,
> bool pps_active, u32 requested_vbus_voltage);
> + bool (*is_vbus_vsafe0v)(struct tcpc_dev *dev);
> };
>
> struct tcpm_port;
> --
> 2.29.2.576.ga3fc446d84-goog
--
heikki
On Tue, Dec 01, 2020 at 08:08:40PM -0800, Badhri Jagan Sridharan wrote:
> Unmask EXTENDED_STATUS_MASK.vSafe0V, ALERT.Extended_Status
> and set vbus_vsafe0v to enable VSAFE0V signalling.
>
> Signed-off-by: Badhri Jagan Sridharan <[email protected]>
Reviewed-by: Guenter Roeck <[email protected]>
> ---
> Changes since v1:
> - Setting auto_discharge_disconnect to true instead of 1 as
> suggested by Guenter.
> ---
> drivers/usb/typec/tcpm/tcpci_maxim.c | 16 +++++++++++++++-
> 1 file changed, 15 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/usb/typec/tcpm/tcpci_maxim.c b/drivers/usb/typec/tcpm/tcpci_maxim.c
> index c1797239bf08..319266329b42 100644
> --- a/drivers/usb/typec/tcpm/tcpci_maxim.c
> +++ b/drivers/usb/typec/tcpm/tcpci_maxim.c
> @@ -112,11 +112,18 @@ static void max_tcpci_init_regs(struct max_tcpci_chip *chip)
> return;
> }
>
> + /* Enable VSAFE0V detection */
> + ret = max_tcpci_write8(chip, TCPC_EXTENDED_STATUS_MASK, TCPC_EXTENDED_STATUS_VSAFE0V);
> + if (ret < 0) {
> + dev_err(chip->dev, "Unable to unmask TCPC_EXTENDED_STATUS_VSAFE0V ret:%d\n", ret);
> + return;
> + }
> +
> alert_mask = TCPC_ALERT_TX_SUCCESS | TCPC_ALERT_TX_DISCARDED | TCPC_ALERT_TX_FAILED |
> TCPC_ALERT_RX_HARD_RST | TCPC_ALERT_RX_STATUS | TCPC_ALERT_CC_STATUS |
> TCPC_ALERT_VBUS_DISCNCT | TCPC_ALERT_RX_BUF_OVF | TCPC_ALERT_POWER_STATUS |
> /* Enable Extended alert for detecting Fast Role Swap Signal */
> - TCPC_ALERT_EXTND;
> + TCPC_ALERT_EXTND | TCPC_ALERT_EXTENDED_STATUS;
>
> ret = max_tcpci_write16(chip, TCPC_ALERT_MASK, alert_mask);
> if (ret < 0) {
> @@ -315,6 +322,12 @@ static irqreturn_t _max_tcpci_irq(struct max_tcpci_chip *chip, u16 status)
> }
> }
>
> + if (status & TCPC_ALERT_EXTENDED_STATUS) {
> + ret = max_tcpci_read8(chip, TCPC_EXTENDED_STATUS, (u8 *)®_status);
> + if (ret >= 0 && (reg_status & TCPC_EXTENDED_STATUS_VSAFE0V))
> + tcpm_vbus_change(chip->port);
> + }
> +
> if (status & TCPC_ALERT_RX_STATUS)
> process_rx(chip, status);
>
> @@ -442,6 +455,7 @@ static int max_tcpci_probe(struct i2c_client *client, const struct i2c_device_id
> chip->data.init = tcpci_init;
> chip->data.frs_sourcing_vbus = max_tcpci_frs_sourcing_vbus;
> chip->data.auto_discharge_disconnect = true;
> + chip->data.vbus_vsafe0v = true;
>
> max_tcpci_init_regs(chip);
> chip->tcpci = tcpci_register_port(chip->dev, &chip->data);
> --
> 2.29.2.576.ga3fc446d84-goog
>
On Tue, Dec 01, 2020 at 08:08:38PM -0800, Badhri Jagan Sridharan wrote:
> TCPM at present lacks the notion of VSAFE0V. There
> are three vbus threshold levels that are critical to track:
> a. vSafe5V - VBUS “5 volts” as defined by the USB
> PD specification.
> b. vSinkDisconnect - Threshold used for transition from
> Attached.SNK to Unattached.SNK.
> c. vSafe0V - VBUS “0 volts” as defined by the USB
> PD specification.
>
> Tracking vSafe0V is crucial for entry into Try.SNK and
> Attached.SRC and turning vbus back on by the source in
> response to hard reset.
>
> From "4.5.2.2.8.2 Exiting from AttachWait.SRC State" section
> in the Type-C spec:
>
> "The port shall transition to Attached.SRC when VBUS is at
> vSafe0V and the SRC.Rd state is detected on exactly one of
> the CC1 or CC2 pins for at least tCCDebounce."
>
> "A DRP that strongly prefers the Sink role may optionally
> transition to Try.SNK instead of Attached.SRC when VBUS
> is at vSafe0V and the SRC.Rd state is detected on exactly
> one of the CC1 or CC2 pins for at least tCCDebounce."
>
> From "7.1.5 Response to Hard Resets" section in the PD spec:
>
> "After establishing the vSafe0V voltage condition on VBUS,
> the Source Shall wait tSrcRecover before re-applying VCONN
> and restoring VBUS to vSafe5V."
>
> vbus_present in the TCPM code tracks vSafe5V(vbus_present is true)
> and vSinkDisconnect(vbus_present is false).
>
> This change adds is_vbus_vsafe0v callback which when set makes
> TCPM query for vSafe0V voltage level when needed.
>
> Since not all TCPC controllers might have the capability
> to report vSafe0V, TCPM assumes that vSafe0V is same as
> vSinkDisconnect when is_vbus_vsafe0v callback is not set.
> This allows TCPM to continue to support controllers which don't
> have the support for reporting vSafe0V.
>
> Introducing vSafe0V helps fix the failure reported at
> "Step 15. CVS verifies PUT remains in AttachWait.SRC for 500ms"
> of "TD 4.7.2 Try. SNK DRP Connect DRP Test" of
> "Universal Serial Bus Type-C (USB Type-C) Functional Test
> Specification Chapters 4 and 5". Here the compliance tester
> intentionally maintains vbus at greater than vSafe0V and expects
> the Product under test to stay in AttachWait.SRC till vbus drops
> to vSafe0V.
>
> Signed-off-by: Badhri Jagan Sridharan <[email protected]>
Reviewed-by: Guenter Roeck <[email protected]>
> ---
> Changes since v1:
> - Changed return type to bool instead of int for
> is_vbus_vsafe0v as suggested by Guenter and updated
> the documentation.
> ---
> drivers/usb/typec/tcpm/tcpm.c | 63 +++++++++++++++++++++++++++++------
> include/linux/usb/tcpm.h | 7 ++++
> 2 files changed, 59 insertions(+), 11 deletions(-)
>
> diff --git a/drivers/usb/typec/tcpm/tcpm.c b/drivers/usb/typec/tcpm/tcpm.c
> index 3bbc1f10af49..4cd6e0196f94 100644
> --- a/drivers/usb/typec/tcpm/tcpm.c
> +++ b/drivers/usb/typec/tcpm/tcpm.c
> @@ -258,7 +258,19 @@ struct tcpm_port {
> bool attached;
> bool connected;
> enum typec_port_type port_type;
> +
> + /*
> + * Set to true when vbus is greater than VSAFE5V min.
> + * Set to false when vbus falls below vSinkDisconnect max threshold.
> + */
> bool vbus_present;
> +
> + /*
> + * Set to true when vbus is less than VSAFE0V max.
> + * Set to false when vbus is greater than VSAFE0V max.
> + */
> + bool vbus_vsafe0v;
> +
> bool vbus_never_low;
> bool vbus_source;
> bool vbus_charge;
> @@ -3094,7 +3106,7 @@ static void run_state_machine(struct tcpm_port *port)
> else if (tcpm_port_is_audio(port))
> tcpm_set_state(port, AUDIO_ACC_ATTACHED,
> PD_T_CC_DEBOUNCE);
> - else if (tcpm_port_is_source(port))
> + else if (tcpm_port_is_source(port) && port->vbus_vsafe0v)
> tcpm_set_state(port,
> tcpm_try_snk(port) ? SNK_TRY
> : SRC_ATTACHED,
> @@ -4097,6 +4109,12 @@ static void _tcpm_pd_vbus_on(struct tcpm_port *port)
> {
> tcpm_log_force(port, "VBUS on");
> port->vbus_present = true;
> + /*
> + * When vbus_present is true i.e. Voltage at VBUS is greater than VSAFE5V implicitly
> + * states that vbus is not at VSAFE0V, hence clear the vbus_vsafe0v flag here.
> + */
> + port->vbus_vsafe0v = false;
> +
> switch (port->state) {
> case SNK_TRANSITION_SINK_VBUS:
> port->explicit_contract = true;
> @@ -4186,16 +4204,8 @@ static void _tcpm_pd_vbus_off(struct tcpm_port *port)
> case SNK_HARD_RESET_SINK_OFF:
> tcpm_set_state(port, SNK_HARD_RESET_WAIT_VBUS, 0);
> break;
> - case SRC_HARD_RESET_VBUS_OFF:
> - /*
> - * After establishing the vSafe0V voltage condition on VBUS, the Source Shall wait
> - * tSrcRecover before re-applying VCONN and restoring VBUS to vSafe5V.
> - */
> - tcpm_set_state(port, SRC_HARD_RESET_VBUS_ON, PD_T_SRC_RECOVER);
> - break;
> case HARD_RESET_SEND:
> break;
> -
> case SNK_TRY:
> /* Do nothing, waiting for timeout */
> break;
> @@ -4266,6 +4276,28 @@ static void _tcpm_pd_vbus_off(struct tcpm_port *port)
> }
> }
>
> +static void _tcpm_pd_vbus_vsafe0v(struct tcpm_port *port)
> +{
> + tcpm_log_force(port, "VBUS VSAFE0V");
> + port->vbus_vsafe0v = true;
> + switch (port->state) {
> + case SRC_HARD_RESET_VBUS_OFF:
> + /*
> + * After establishing the vSafe0V voltage condition on VBUS, the Source Shall wait
> + * tSrcRecover before re-applying VCONN and restoring VBUS to vSafe5V.
> + */
> + tcpm_set_state(port, SRC_HARD_RESET_VBUS_ON, PD_T_SRC_RECOVER);
> + break;
> + case SRC_ATTACH_WAIT:
> + if (tcpm_port_is_source(port))
> + tcpm_set_state(port, tcpm_try_snk(port) ? SNK_TRY : SRC_ATTACHED,
> + PD_T_CC_DEBOUNCE);
> + break;
> + default:
> + break;
> + }
> +}
> +
> static void _tcpm_pd_hard_reset(struct tcpm_port *port)
> {
> tcpm_log_force(port, "Received hard reset");
> @@ -4301,10 +4333,19 @@ static void tcpm_pd_event_handler(struct kthread_work *work)
> bool vbus;
>
> vbus = port->tcpc->get_vbus(port->tcpc);
> - if (vbus)
> + if (vbus) {
> _tcpm_pd_vbus_on(port);
> - else
> + } else {
> _tcpm_pd_vbus_off(port);
> + /*
> + * When TCPC does not support detecting vsafe0v voltage level,
> + * treat vbus absent as vsafe0v. Else invoke is_vbus_vsafe0v
> + * to see if vbus has discharge to VSAFE0V.
> + */
> + if (!port->tcpc->is_vbus_vsafe0v ||
> + port->tcpc->is_vbus_vsafe0v(port->tcpc))
> + _tcpm_pd_vbus_vsafe0v(port);
> + }
> }
> if (events & TCPM_CC_EVENT) {
> enum typec_cc_status cc1, cc2;
> diff --git a/include/linux/usb/tcpm.h b/include/linux/usb/tcpm.h
> index e68aaa12886f..3e39874cfac4 100644
> --- a/include/linux/usb/tcpm.h
> +++ b/include/linux/usb/tcpm.h
> @@ -98,6 +98,12 @@ enum tcpm_transmit_type {
> * will be turned on. requested_vbus_voltage is set to 0 when vbus
> * is going to disappear knowingly i.e. during PR_SWAP and
> * HARD_RESET etc.
> + * @is_vbus_vsafe0v:
> + * Optional; TCPCI spec based TCPC implementations are expected to
> + * detect VSAFE0V voltage level at vbus. When detection of VSAFE0V
> + * is supported by TCPC, set this callback for TCPM to query
> + * whether vbus is at VSAFE0V when needed.
> + * Returns true when vbus is at VSAFE0V, false otherwise.
> */
> struct tcpc_dev {
> struct fwnode_handle *fwnode;
> @@ -128,6 +134,7 @@ struct tcpc_dev {
> int (*enable_auto_vbus_discharge)(struct tcpc_dev *dev, bool enable);
> int (*set_auto_vbus_discharge_threshold)(struct tcpc_dev *dev, enum typec_pwr_opmode mode,
> bool pps_active, u32 requested_vbus_voltage);
> + bool (*is_vbus_vsafe0v)(struct tcpc_dev *dev);
> };
>
> struct tcpm_port;
> --
> 2.29.2.576.ga3fc446d84-goog
>