Adding Aspeed AST2400 and AST2600 binding for edac driver.
Signed-off-by: Troy Lee <[email protected]>
---
.../devicetree/bindings/edac/aspeed-sdram-edac.txt | 9 ++++++---
1 file changed, 6 insertions(+), 3 deletions(-)
diff --git a/Documentation/devicetree/bindings/edac/aspeed-sdram-edac.txt b/Documentation/devicetree/bindings/edac/aspeed-sdram-edac.txt
index 6a0f3d90d682..8ca9e0a049d8 100644
--- a/Documentation/devicetree/bindings/edac/aspeed-sdram-edac.txt
+++ b/Documentation/devicetree/bindings/edac/aspeed-sdram-edac.txt
@@ -1,6 +1,6 @@
-Aspeed AST2500 SoC EDAC node
+Aspeed BMC SoC EDAC node
-The Aspeed AST2500 SoC supports DDR3 and DDR4 memory with and without ECC (error
+The Aspeed BMC SoC supports DDR3 and DDR4 memory with and without ECC (error
correction check).
The memory controller supports SECDED (single bit error correction, double bit
@@ -11,7 +11,10 @@ Note, the bootloader must configure ECC mode in the memory controller.
Required properties:
-- compatible: should be "aspeed,ast2500-sdram-edac"
+- compatible: should be one of
+ - "aspeed,ast2400-sdram-edac"
+ - "aspeed,ast2500-sdram-edac"
+ - "aspeed,ast2600-sdram-edac"
- reg: sdram controller register set should be <0x1e6e0000 0x174>
- interrupts: should be AVIC interrupt #0
--
2.17.1
Adding Aspeed AST2600 edac node into common devicetree.
Signed-off-by: Troy Lee <[email protected]>
---
arch/arm/boot/dts/aspeed-g6.dtsi | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/arch/arm/boot/dts/aspeed-g6.dtsi b/arch/arm/boot/dts/aspeed-g6.dtsi
index b58220a49cbd..74367ee96f20 100644
--- a/arch/arm/boot/dts/aspeed-g6.dtsi
+++ b/arch/arm/boot/dts/aspeed-g6.dtsi
@@ -69,6 +69,12 @@
always-on;
};
+ edac: sdram@1e6e0000 {
+ compatible = "aspeed,ast2600-sdram-edac", "syscon";
+ reg = <0x1e6e0000 0x174>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
ahb {
compatible = "simple-bus";
#address-cells = <1>;
--
2.17.1
Adding AST2400 and AST2600 edac driver support.
Signed-off-by: Troy Lee <[email protected]>
---
Changes since v2:
- Remove cross dependencies export functions
- Update Kconfig depends on ARCH_ASPEED
- Patch create against latest Linux kernel mainline
---
drivers/edac/Kconfig | 6 +++---
drivers/edac/aspeed_edac.c | 15 +++++----------
2 files changed, 8 insertions(+), 13 deletions(-)
diff --git a/drivers/edac/Kconfig b/drivers/edac/Kconfig
index 7a47680d6f07..c410331e8ee8 100644
--- a/drivers/edac/Kconfig
+++ b/drivers/edac/Kconfig
@@ -515,10 +515,10 @@ config EDAC_QCOM
health, you should probably say 'Y' here.
config EDAC_ASPEED
- tristate "Aspeed AST 2500 SoC"
- depends on MACH_ASPEED_G5
+ tristate "Aspeed AST BMC SoC"
+ depends on ARCH_ASPEED
help
- Support for error detection and correction on the Aspeed AST 2500 SoC.
+ Support for error detection and correction on the Aspeed AST BMC SoC.
First, ECC must be configured in the bootloader. Then, this driver
will expose error counters via the EDAC kernel framework.
diff --git a/drivers/edac/aspeed_edac.c b/drivers/edac/aspeed_edac.c
index fde809efc520..c9d1d8a8fcba 100644
--- a/drivers/edac/aspeed_edac.c
+++ b/drivers/edac/aspeed_edac.c
@@ -239,7 +239,7 @@ static int init_csrows(struct mem_ctl_info *mci)
int rc;
/* retrieve info about physical memory from device tree */
- np = of_find_node_by_path("/memory");
+ np = of_find_node_by_name(NULL, "memory");
if (!np) {
dev_err(mci->pdev, "dt: missing /memory node\n");
return -ENODEV;
@@ -282,7 +282,6 @@ static int aspeed_probe(struct platform_device *pdev)
struct edac_mc_layer layers[2];
struct mem_ctl_info *mci;
void __iomem *regs;
- u32 reg04;
int rc;
regs = devm_platform_ioremap_resource(pdev, 0);
@@ -294,13 +293,6 @@ static int aspeed_probe(struct platform_device *pdev)
if (IS_ERR(aspeed_regmap))
return PTR_ERR(aspeed_regmap);
- /* bail out if ECC mode is not configured */
- regmap_read(aspeed_regmap, ASPEED_MCR_CONF, ®04);
- if (!(reg04 & ASPEED_MCR_CONF_ECC)) {
- dev_err(&pdev->dev, "ECC mode is not configured in u-boot\n");
- return -EPERM;
- }
-
edac_op_state = EDAC_OPSTATE_INT;
/* allocate & init EDAC MC data structure */
@@ -375,10 +367,13 @@ static int aspeed_remove(struct platform_device *pdev)
static const struct of_device_id aspeed_of_match[] = {
+ { .compatible = "aspeed,ast2400-sdram-edac" },
{ .compatible = "aspeed,ast2500-sdram-edac" },
+ { .compatible = "aspeed,ast2600-sdram-edac" },
{},
};
+MODULE_DEVICE_TABLE(of, aspeed_of_match);
static struct platform_driver aspeed_driver = {
.driver = {
@@ -392,5 +387,5 @@ module_platform_driver(aspeed_driver);
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Stefan Schaeckeler <[email protected]>");
-MODULE_DESCRIPTION("Aspeed AST2500 EDAC driver");
+MODULE_DESCRIPTION("Aspeed BMC SoC EDAC driver");
MODULE_VERSION("1.0");
--
2.17.1
On Wed, 2 Dec 2020, at 20:42, Troy Lee wrote:
> Adding AST2400 and AST2600 edac driver support.
>
> Signed-off-by: Troy Lee <[email protected]>
> ---
> Changes since v2:
> - Remove cross dependencies export functions
> - Update Kconfig depends on ARCH_ASPEED
> - Patch create against latest Linux kernel mainline
>
> ---
> drivers/edac/Kconfig | 6 +++---
> drivers/edac/aspeed_edac.c | 15 +++++----------
> 2 files changed, 8 insertions(+), 13 deletions(-)
>
> diff --git a/drivers/edac/Kconfig b/drivers/edac/Kconfig
> index 7a47680d6f07..c410331e8ee8 100644
> --- a/drivers/edac/Kconfig
> +++ b/drivers/edac/Kconfig
> @@ -515,10 +515,10 @@ config EDAC_QCOM
> health, you should probably say 'Y' here.
>
> config EDAC_ASPEED
> - tristate "Aspeed AST 2500 SoC"
> - depends on MACH_ASPEED_G5
> + tristate "Aspeed AST BMC SoC"
> + depends on ARCH_ASPEED
> help
> - Support for error detection and correction on the Aspeed AST 2500 SoC.
> + Support for error detection and correction on the Aspeed AST BMC SoC.
>
> First, ECC must be configured in the bootloader. Then, this driver
> will expose error counters via the EDAC kernel framework.
> diff --git a/drivers/edac/aspeed_edac.c b/drivers/edac/aspeed_edac.c
> index fde809efc520..c9d1d8a8fcba 100644
> --- a/drivers/edac/aspeed_edac.c
> +++ b/drivers/edac/aspeed_edac.c
> @@ -239,7 +239,7 @@ static int init_csrows(struct mem_ctl_info *mci)
> int rc;
>
> /* retrieve info about physical memory from device tree */
> - np = of_find_node_by_path("/memory");
> + np = of_find_node_by_name(NULL, "memory");
> if (!np) {
> dev_err(mci->pdev, "dt: missing /memory node\n");
> return -ENODEV;
> @@ -282,7 +282,6 @@ static int aspeed_probe(struct platform_device *pdev)
> struct edac_mc_layer layers[2];
> struct mem_ctl_info *mci;
> void __iomem *regs;
> - u32 reg04;
> int rc;
>
> regs = devm_platform_ioremap_resource(pdev, 0);
> @@ -294,13 +293,6 @@ static int aspeed_probe(struct platform_device *pdev)
> if (IS_ERR(aspeed_regmap))
> return PTR_ERR(aspeed_regmap);
>
> - /* bail out if ECC mode is not configured */
> - regmap_read(aspeed_regmap, ASPEED_MCR_CONF, ®04);
> - if (!(reg04 & ASPEED_MCR_CONF_ECC)) {
> - dev_err(&pdev->dev, "ECC mode is not configured in u-boot\n");
> - return -EPERM;
> - }
> -
It might pay to separate this out as I think it's unrelated to the supporting
the AST2[45]00?
Other than that I think the patch is on the right track.
Thanks for the quick responses Troy!
Andrew
> edac_op_state = EDAC_OPSTATE_INT;
>
> /* allocate & init EDAC MC data structure */
> @@ -375,10 +367,13 @@ static int aspeed_remove(struct platform_device *pdev)
>
>
> static const struct of_device_id aspeed_of_match[] = {
> + { .compatible = "aspeed,ast2400-sdram-edac" },
> { .compatible = "aspeed,ast2500-sdram-edac" },
> + { .compatible = "aspeed,ast2600-sdram-edac" },
> {},
> };
>
> +MODULE_DEVICE_TABLE(of, aspeed_of_match);
>
> static struct platform_driver aspeed_driver = {
> .driver = {
> @@ -392,5 +387,5 @@ module_platform_driver(aspeed_driver);
>
> MODULE_LICENSE("GPL");
> MODULE_AUTHOR("Stefan Schaeckeler <[email protected]>");
> -MODULE_DESCRIPTION("Aspeed AST2500 EDAC driver");
> +MODULE_DESCRIPTION("Aspeed BMC SoC EDAC driver");
> MODULE_VERSION("1.0");
> --
> 2.17.1
>
>