Use the typical startup times from the data sheet so boards get a
reasonable default. Not setting any enable time can lead to board hangs
when e.g. clocks are enabled too soon afterwards.
This fixes gpu power domain resume on the Librem 5.
Signed-off-by: Guido Günther <[email protected]>
---
v2
- As per review comment by Matti Vaittinen
https://lore.kernel.org/lkml/[email protected]/
Use defines instead of plain values
- As per review comment by Mark Brown
https://lore.kernel.org/lkml/[email protected]/
Drop cover letter
---
drivers/regulator/bd718x7-regulator.c | 27 ++++++++++++++++++++++++
include/linux/mfd/rohm-bd718x7.h | 30 +++++++++++++++++++++++++++
2 files changed, 57 insertions(+)
diff --git a/drivers/regulator/bd718x7-regulator.c b/drivers/regulator/bd718x7-regulator.c
index e6d5d98c3cea..f7597832d2c5 100644
--- a/drivers/regulator/bd718x7-regulator.c
+++ b/drivers/regulator/bd718x7-regulator.c
@@ -613,6 +613,7 @@ static struct bd718xx_regulator_data bd71847_regulators[] = {
.vsel_mask = DVS_BUCK_RUN_MASK,
.enable_reg = BD718XX_REG_BUCK1_CTRL,
.enable_mask = BD718XX_BUCK_EN,
+ .enable_time = BD71847_BUCK1_STARTUP_TIME,
.owner = THIS_MODULE,
.of_parse_cb = buck_set_hw_dvs_levels,
},
@@ -646,6 +647,7 @@ static struct bd718xx_regulator_data bd71847_regulators[] = {
.vsel_mask = DVS_BUCK_RUN_MASK,
.enable_reg = BD718XX_REG_BUCK2_CTRL,
.enable_mask = BD718XX_BUCK_EN,
+ .enable_time = BD71847_BUCK2_STARTUP_TIME,
.owner = THIS_MODULE,
.of_parse_cb = buck_set_hw_dvs_levels,
},
@@ -680,6 +682,7 @@ static struct bd718xx_regulator_data bd71847_regulators[] = {
.linear_range_selectors = bd71847_buck3_volt_range_sel,
.enable_reg = BD718XX_REG_1ST_NODVS_BUCK_CTRL,
.enable_mask = BD718XX_BUCK_EN,
+ .enable_time = BD71847_BUCK3_STARTUP_TIME,
.owner = THIS_MODULE,
},
.init = {
@@ -706,6 +709,7 @@ static struct bd718xx_regulator_data bd71847_regulators[] = {
.vsel_range_mask = BD71847_BUCK4_RANGE_MASK,
.linear_range_selectors = bd71847_buck4_volt_range_sel,
.enable_mask = BD718XX_BUCK_EN,
+ .enable_time = BD71847_BUCK4_STARTUP_TIME,
.owner = THIS_MODULE,
},
.init = {
@@ -727,6 +731,7 @@ static struct bd718xx_regulator_data bd71847_regulators[] = {
.vsel_mask = BD718XX_3RD_NODVS_BUCK_MASK,
.enable_reg = BD718XX_REG_3RD_NODVS_BUCK_CTRL,
.enable_mask = BD718XX_BUCK_EN,
+ .enable_time = BD71847_BUCK5_STARTUP_TIME,
.owner = THIS_MODULE,
},
.init = {
@@ -750,6 +755,7 @@ static struct bd718xx_regulator_data bd71847_regulators[] = {
.vsel_mask = BD718XX_4TH_NODVS_BUCK_MASK,
.enable_reg = BD718XX_REG_4TH_NODVS_BUCK_CTRL,
.enable_mask = BD718XX_BUCK_EN,
+ .enable_time = BD71847_BUCK6_STARTUP_TIME,
.owner = THIS_MODULE,
},
.init = {
@@ -775,6 +781,7 @@ static struct bd718xx_regulator_data bd71847_regulators[] = {
.linear_range_selectors = bd718xx_ldo1_volt_range_sel,
.enable_reg = BD718XX_REG_LDO1_VOLT,
.enable_mask = BD718XX_LDO_EN,
+ .enable_time = BD71847_LDO1_STARTUP_TIME,
.owner = THIS_MODULE,
},
.init = {
@@ -796,6 +803,7 @@ static struct bd718xx_regulator_data bd71847_regulators[] = {
.n_voltages = ARRAY_SIZE(ldo_2_volts),
.enable_reg = BD718XX_REG_LDO2_VOLT,
.enable_mask = BD718XX_LDO_EN,
+ .enable_time = BD71847_LDO2_STARTUP_TIME,
.owner = THIS_MODULE,
},
.init = {
@@ -818,6 +826,7 @@ static struct bd718xx_regulator_data bd71847_regulators[] = {
.vsel_mask = BD718XX_LDO3_MASK,
.enable_reg = BD718XX_REG_LDO3_VOLT,
.enable_mask = BD718XX_LDO_EN,
+ .enable_time = BD71847_LDO3_STARTUP_TIME,
.owner = THIS_MODULE,
},
.init = {
@@ -840,6 +849,7 @@ static struct bd718xx_regulator_data bd71847_regulators[] = {
.vsel_mask = BD718XX_LDO4_MASK,
.enable_reg = BD718XX_REG_LDO4_VOLT,
.enable_mask = BD718XX_LDO_EN,
+ .enable_time = BD71847_LDO4_STARTUP_TIME,
.owner = THIS_MODULE,
},
.init = {
@@ -865,6 +875,7 @@ static struct bd718xx_regulator_data bd71847_regulators[] = {
.linear_range_selectors = bd71847_ldo5_volt_range_sel,
.enable_reg = BD718XX_REG_LDO5_VOLT,
.enable_mask = BD718XX_LDO_EN,
+ .enable_time = BD71847_LDO5_STARTUP_TIME,
.owner = THIS_MODULE,
},
.init = {
@@ -889,6 +900,7 @@ static struct bd718xx_regulator_data bd71847_regulators[] = {
.vsel_mask = BD718XX_LDO6_MASK,
.enable_reg = BD718XX_REG_LDO6_VOLT,
.enable_mask = BD718XX_LDO_EN,
+ .enable_time = BD71847_LDO6_STARTUP_TIME,
.owner = THIS_MODULE,
},
.init = {
@@ -942,6 +954,7 @@ static struct bd718xx_regulator_data bd71837_regulators[] = {
.vsel_mask = DVS_BUCK_RUN_MASK,
.enable_reg = BD718XX_REG_BUCK1_CTRL,
.enable_mask = BD718XX_BUCK_EN,
+ .enable_time = BD71837_BUCK1_STARTUP_TIME,
.owner = THIS_MODULE,
.of_parse_cb = buck_set_hw_dvs_levels,
},
@@ -975,6 +988,7 @@ static struct bd718xx_regulator_data bd71837_regulators[] = {
.vsel_mask = DVS_BUCK_RUN_MASK,
.enable_reg = BD718XX_REG_BUCK2_CTRL,
.enable_mask = BD718XX_BUCK_EN,
+ .enable_time = BD71837_BUCK2_STARTUP_TIME,
.owner = THIS_MODULE,
.of_parse_cb = buck_set_hw_dvs_levels,
},
@@ -1005,6 +1019,7 @@ static struct bd718xx_regulator_data bd71837_regulators[] = {
.vsel_mask = DVS_BUCK_RUN_MASK,
.enable_reg = BD71837_REG_BUCK3_CTRL,
.enable_mask = BD718XX_BUCK_EN,
+ .enable_time = BD71837_BUCK3_STARTUP_TIME,
.owner = THIS_MODULE,
.of_parse_cb = buck_set_hw_dvs_levels,
},
@@ -1033,6 +1048,7 @@ static struct bd718xx_regulator_data bd71837_regulators[] = {
.vsel_mask = DVS_BUCK_RUN_MASK,
.enable_reg = BD71837_REG_BUCK4_CTRL,
.enable_mask = BD718XX_BUCK_EN,
+ .enable_time = BD71837_BUCK4_STARTUP_TIME,
.owner = THIS_MODULE,
.of_parse_cb = buck_set_hw_dvs_levels,
},
@@ -1065,6 +1081,7 @@ static struct bd718xx_regulator_data bd71837_regulators[] = {
.linear_range_selectors = bd71837_buck5_volt_range_sel,
.enable_reg = BD718XX_REG_1ST_NODVS_BUCK_CTRL,
.enable_mask = BD718XX_BUCK_EN,
+ .enable_time = BD71837_BUCK5_STARTUP_TIME,
.owner = THIS_MODULE,
},
.init = {
@@ -1088,6 +1105,7 @@ static struct bd718xx_regulator_data bd71837_regulators[] = {
.vsel_mask = BD71837_BUCK6_MASK,
.enable_reg = BD718XX_REG_2ND_NODVS_BUCK_CTRL,
.enable_mask = BD718XX_BUCK_EN,
+ .enable_time = BD71837_BUCK6_STARTUP_TIME,
.owner = THIS_MODULE,
},
.init = {
@@ -1109,6 +1127,7 @@ static struct bd718xx_regulator_data bd71837_regulators[] = {
.vsel_mask = BD718XX_3RD_NODVS_BUCK_MASK,
.enable_reg = BD718XX_REG_3RD_NODVS_BUCK_CTRL,
.enable_mask = BD718XX_BUCK_EN,
+ .enable_time = BD71837_BUCK7_STARTUP_TIME,
.owner = THIS_MODULE,
},
.init = {
@@ -1132,6 +1151,7 @@ static struct bd718xx_regulator_data bd71837_regulators[] = {
.vsel_mask = BD718XX_4TH_NODVS_BUCK_MASK,
.enable_reg = BD718XX_REG_4TH_NODVS_BUCK_CTRL,
.enable_mask = BD718XX_BUCK_EN,
+ .enable_time = BD71837_BUCK8_STARTUP_TIME,
.owner = THIS_MODULE,
},
.init = {
@@ -1157,6 +1177,7 @@ static struct bd718xx_regulator_data bd71837_regulators[] = {
.linear_range_selectors = bd718xx_ldo1_volt_range_sel,
.enable_reg = BD718XX_REG_LDO1_VOLT,
.enable_mask = BD718XX_LDO_EN,
+ .enable_time = BD71837_LDO1_STARTUP_TIME,
.owner = THIS_MODULE,
},
.init = {
@@ -1178,6 +1199,7 @@ static struct bd718xx_regulator_data bd71837_regulators[] = {
.n_voltages = ARRAY_SIZE(ldo_2_volts),
.enable_reg = BD718XX_REG_LDO2_VOLT,
.enable_mask = BD718XX_LDO_EN,
+ .enable_time = BD71837_LDO2_STARTUP_TIME,
.owner = THIS_MODULE,
},
.init = {
@@ -1200,6 +1222,7 @@ static struct bd718xx_regulator_data bd71837_regulators[] = {
.vsel_mask = BD718XX_LDO3_MASK,
.enable_reg = BD718XX_REG_LDO3_VOLT,
.enable_mask = BD718XX_LDO_EN,
+ .enable_time = BD71837_LDO3_STARTUP_TIME,
.owner = THIS_MODULE,
},
.init = {
@@ -1222,6 +1245,7 @@ static struct bd718xx_regulator_data bd71837_regulators[] = {
.vsel_mask = BD718XX_LDO4_MASK,
.enable_reg = BD718XX_REG_LDO4_VOLT,
.enable_mask = BD718XX_LDO_EN,
+ .enable_time = BD71837_LDO4_STARTUP_TIME,
.owner = THIS_MODULE,
},
.init = {
@@ -1246,6 +1270,7 @@ static struct bd718xx_regulator_data bd71837_regulators[] = {
.vsel_mask = BD71837_LDO5_MASK,
.enable_reg = BD718XX_REG_LDO5_VOLT,
.enable_mask = BD718XX_LDO_EN,
+ .enable_time = BD71837_LDO5_STARTUP_TIME,
.owner = THIS_MODULE,
},
.init = {
@@ -1272,6 +1297,7 @@ static struct bd718xx_regulator_data bd71837_regulators[] = {
.vsel_mask = BD718XX_LDO6_MASK,
.enable_reg = BD718XX_REG_LDO6_VOLT,
.enable_mask = BD718XX_LDO_EN,
+ .enable_time = BD71837_LDO6_STARTUP_TIME,
.owner = THIS_MODULE,
},
.init = {
@@ -1296,6 +1322,7 @@ static struct bd718xx_regulator_data bd71837_regulators[] = {
.vsel_mask = BD71837_LDO7_MASK,
.enable_reg = BD71837_REG_LDO7_VOLT,
.enable_mask = BD718XX_LDO_EN,
+ .enable_time = BD71837_LDO7_STARTUP_TIME,
.owner = THIS_MODULE,
},
.init = {
diff --git a/include/linux/mfd/rohm-bd718x7.h b/include/linux/mfd/rohm-bd718x7.h
index bee2474a8f9f..fba80dc2c1d5 100644
--- a/include/linux/mfd/rohm-bd718x7.h
+++ b/include/linux/mfd/rohm-bd718x7.h
@@ -323,4 +323,34 @@ struct bd718xx {
struct regmap_irq_chip_data *irq_data;
};
+/* Typical regulator startup times as per data sheet in uS */
+#define BD71847_BUCK1_STARTUP_TIME 144
+#define BD71847_BUCK2_STARTUP_TIME 162
+#define BD71847_BUCK3_STARTUP_TIME 162
+#define BD71847_BUCK4_STARTUP_TIME 240
+#define BD71847_BUCK5_STARTUP_TIME 270
+#define BD71847_BUCK6_STARTUP_TIME 200
+#define BD71847_LDO1_STARTUP_TIME 440
+#define BD71847_LDO2_STARTUP_TIME 370
+#define BD71847_LDO3_STARTUP_TIME 310
+#define BD71847_LDO4_STARTUP_TIME 400
+#define BD71847_LDO5_STARTUP_TIME 530
+#define BD71847_LDO6_STARTUP_TIME 400
+
+#define BD71837_BUCK1_STARTUP_TIME 160
+#define BD71837_BUCK2_STARTUP_TIME 180
+#define BD71837_BUCK3_STARTUP_TIME 180
+#define BD71837_BUCK4_STARTUP_TIME 180
+#define BD71837_BUCK5_STARTUP_TIME 160
+#define BD71837_BUCK6_STARTUP_TIME 240
+#define BD71837_BUCK7_STARTUP_TIME 220
+#define BD71837_BUCK8_STARTUP_TIME 200
+#define BD71837_LDO1_STARTUP_TIME 440
+#define BD71837_LDO2_STARTUP_TIME 370
+#define BD71837_LDO3_STARTUP_TIME 310
+#define BD71837_LDO4_STARTUP_TIME 400
+#define BD71837_LDO5_STARTUP_TIME 310
+#define BD71837_LDO6_STARTUP_TIME 400
+#define BD71837_LDO7_STARTUP_TIME 530
+
#endif /* __LINUX_MFD_BD718XX_H__ */
--
2.29.2
On Fri, 2020-12-18 at 19:38 +0100, Guido Günther wrote:
> Use the typical startup times from the data sheet so boards get a
> reasonable default. Not setting any enable time can lead to board
> hangs
> when e.g. clocks are enabled too soon afterwards.
>
> This fixes gpu power domain resume on the Librem 5.
>
> Signed-off-by: Guido Günther <[email protected]>
>
> ---
> v2
> - As per review comment by Matti Vaittinen
>
> https://lore.kernel.org/lkml/[email protected]/
> Use defines instead of plain values
> - As per review comment by Mark Brown
> https://lore.kernel.org/lkml/[email protected]/
> Drop cover letter
> ---
> drivers/regulator/bd718x7-regulator.c | 27 ++++++++++++++++++++++++
> include/linux/mfd/rohm-bd718x7.h | 30
Thanks again Guido.
I might have preferred having the defines in bd718x7-regulator.c as
they are not likely to be used outside this file. That would have
strictly limited the change to regulator subsystem. Having them in the
header is still fine with me if it works for Mark & others. (I don't
think these defines need much of changes in the future).
Reviewed-by: Matti Vaittinen <[email protected]>
Best Regards
Matti Vaittinen
Hi,
On Mon, Dec 21, 2020 at 06:08:15AM +0000, Vaittinen, Matti wrote:
>
> On Fri, 2020-12-18 at 19:38 +0100, Guido G?nther wrote:
> > Use the typical startup times from the data sheet so boards get a
> > reasonable default. Not setting any enable time can lead to board
> > hangs
> > when e.g. clocks are enabled too soon afterwards.
> >
> > This fixes gpu power domain resume on the Librem 5.
> >
> > Signed-off-by: Guido G?nther <[email protected]>
> >
> > ---
> > v2
> > - As per review comment by Matti Vaittinen
> >
> > https://lore.kernel.org/lkml/[email protected]/
> > Use defines instead of plain values
> > - As per review comment by Mark Brown
> > https://lore.kernel.org/lkml/[email protected]/
> > Drop cover letter
> > ---
> > drivers/regulator/bd718x7-regulator.c | 27 ++++++++++++++++++++++++
> > include/linux/mfd/rohm-bd718x7.h | 30
>
> Thanks again Guido.
> I might have preferred having the defines in bd718x7-regulator.c as
> they are not likely to be used outside this file. That would have
In fact that's where I had them first, then noticing other regulator
related defines in the mfd header. I can shift those around need be.
Cheers,
-- Guido
> strictly limited the change to regulator subsystem. Having them in the
> header is still fine with me if it works for Mark & others. (I don't
> think these defines need much of changes in the future).
>
> Reviewed-by: Matti Vaittinen <[email protected]>
>
>
> Best Regards
> Matti Vaittinen
>
On Fri, Dec 18, 2020 at 07:38:07PM +0100, Guido G?nther wrote:
> Use the typical startup times from the data sheet so boards get a
> reasonable default. Not setting any enable time can lead to board hangs
> when e.g. clocks are enabled too soon afterwards.
Please submit patches using subject lines reflecting the style for the
subsystem, this makes it easier for people to identify relevant patches.
Look at what existing commits in the area you're changing are doing and
make sure your subject lines visually resemble what they're doing.
There's no need to resubmit to fix this alone.