2021-03-04 23:29:48

by Heiko Thiery

[permalink] [raw]
Subject: [PATCH v4 0/2] add Kontron pITX-imx8m board

This patch series adds support for the Kontron pITX-imx8m board:

https://www.kontron.com/products/boards-and-standard-form-factors/single-board-computer/pitx-imx8m.html

Heiko Thiery (2):
dt-bindings: arm: fsl: add Kontron pITX-imx8m board
arm64: dts: fsl: add support for Kontron pitx-imx8m board

.../devicetree/bindings/arm/fsl.yaml | 1 +
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../freescale/imx8mq-kontron-pitx-imx8m.dts | 611 ++++++++++++++++++
3 files changed, 613 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts

--
2.30.0


2021-03-04 23:30:37

by Heiko Thiery

[permalink] [raw]
Subject: [PATCH v4 1/2] dt-bindings: arm: fsl: add Kontron pITX-imx8m board

Add the Kontron pITX-imx8m board.

Signed-off-by: Heiko Thiery <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
---
v2:
- bring in correct alphabetical order

v3:
- no change

v4:
- no change

Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 297c87f45db8..6d121bc9af8d 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -733,6 +733,7 @@ properties:
- einfochips,imx8mq-thor96 # i.MX8MQ Thor96 Board
- fsl,imx8mq-evk # i.MX8MQ EVK Board
- google,imx8mq-phanbell # Google Coral Edge TPU
+ - kontron,pitx-imx8m # Kontron pITX-imx8m Board
- purism,librem5-devkit # Purism Librem5 devkit
- solidrun,hummingboard-pulse # SolidRun Hummingboard Pulse
- technexion,pico-pi-imx8m # TechNexion PICO-PI-8M evk
--
2.30.0

2021-03-04 23:30:59

by Heiko Thiery

[permalink] [raw]
Subject: [PATCH v4 2/2] arm64: dts: fsl: add support for Kontron pitx-imx8m board

The Kontron pitx-imx8m board is based on an i.MX8MQ soc.

Signed-off-by: Heiko Thiery <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Michael Walle <[email protected]>
---
v2:
- bring root nodes in alphabetical order
- remove pinctrl_gpio_keys for pciewake
- remove pinctrl_sai2 and pinctrl_spdfif1 since it is not used yet

Thanks to Michael Walle:
- add pinctrl for regulator-v-3v3-sd
- add name for regulator swbst
- add comment about currently unused audio codec
- put usb_phy entry in correct alphabetical order

Thanks to Krzysztof Kozlowski:
- use generic names for pcie-refclk, tpm, fan-controller, sensor
- remove empty line
- fix group name to match schema (ecspi2cs -> ecspi2csgrp)

v3:
Thanks to Michael Walle:
- set compatible as first in regulator-v-3v3-sd node
- remove audio-codec@1a node

Thanks to Krzysztof Kozlowski:
- use more generic name for pcie reference clock

v4:
Thanks to Fabio Estevam:
- rename regulator node
- remove tpm-reset node
- remove usb-hub-reset
- use reset-gpios for ethernet phy instead of phy-reset-gpios
- remove disable-gpio and ext_osc property from pcie0
- remove ext_osc property from pcie1

arch/arm64/boot/dts/freescale/Makefile | 1 +
.../freescale/imx8mq-kontron-pitx-imx8m.dts | 611 ++++++++++++++++++
2 files changed, 612 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 6438db3822f8..9fc2c6f64407 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -47,6 +47,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-hummingboard-pulse.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mq-kontron-pitx-imx8m.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r2.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r3.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts b/arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts
new file mode 100644
index 000000000000..91a9ceb10305
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts
@@ -0,0 +1,611 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree File for the Kontron pitx-imx8m board.
+ *
+ * Copyright (C) 2021 Heiko Thiery <[email protected]>
+ */
+
+/dts-v1/;
+
+#include "imx8mq.dtsi"
+#include <dt-bindings/net/ti-dp83867.h>
+
+/ {
+ model = "Kontron pITX-imx8m";
+ compatible = "kontron,pitx-imx8m", "fsl,imx8mq";
+
+ aliases {
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
+ i2c2 = &i2c3;
+ mmc0 = &usdhc1;
+ mmc1 = &usdhc2;
+ serial0 = &uart1;
+ serial1 = &uart2;
+ serial2 = &uart3;
+ spi0 = &qspi0;
+ spi1 = &ecspi2;
+ };
+
+ chosen {
+ stdout-path = "serial2:115200n8";
+ };
+
+ pcie0_refclk: pcie0-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ };
+
+ pcie1_refclk: pcie1-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ };
+
+ reg_usdhc2_vmmc: regulator-usdhc2-vmmc {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_usdhc2>;
+ regulator-name = "V_3V3_SD";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+ off-on-delay-us = <20000>;
+ enable-active-high;
+ };
+};
+
+&ecspi2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2 &pinctrl_ecspi2_cs>;
+ cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ tpm@0 {
+ compatible = "infineon,slb9670";
+ reg = <0>;
+ spi-max-frequency = <43000000>;
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec1>;
+ phy-mode = "rgmii-id";
+ phy-handle = <&ethphy0>;
+ fsl,magic-packet;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+ ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ reset-gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ pmic@8 {
+ compatible = "fsl,pfuze100";
+ fsl,pfuze-support-disable-sw;
+ reg = <0x8>;
+
+ regulators {
+ sw1a_reg: sw1ab {
+ regulator-name = "V_0V9_GPU";
+ regulator-min-microvolt = <825000>;
+ regulator-max-microvolt = <1100000>;
+ };
+
+ sw1c_reg: sw1c {
+ regulator-name = "V_0V9_VPU";
+ regulator-min-microvolt = <825000>;
+ regulator-max-microvolt = <1100000>;
+ };
+
+ sw2_reg: sw2 {
+ regulator-name = "V_1V1_NVCC_DRAM";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ sw3a_reg: sw3ab {
+ regulator-name = "V_1V0_DRAM";
+ regulator-min-microvolt = <825000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ sw4_reg: sw4 {
+ regulator-name = "V_1V8_S0";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ swbst_reg: swbst {
+ regulator-name = "NC";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-name = "V_0V9_SNVS";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-name = "V_0V55_VREF_DDR";
+ regulator-always-on;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-name = "V_1V5_CSI";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-name = "V_0V9_PHY";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <975000>;
+ regulator-always-on;
+ };
+
+ vgen3_reg: vgen3 {
+ regulator-name = "V_1V8_PHY";
+ regulator-min-microvolt = <1675000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-always-on;
+ };
+
+ vgen4_reg: vgen4 {
+ regulator-name = "V_1V8_VDDA";
+ regulator-min-microvolt = <1625000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-always-on;
+ };
+
+ vgen5_reg: vgen5 {
+ regulator-name = "V_3V3_PHY";
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3625000>;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vgen6 {
+ regulator-name = "V_2V8_CAM";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+ };
+
+ fan-controller@1b {
+ compatible = "maxim,max6650";
+ reg = <0x1b>;
+ maxim,fan-microvolt = <5000000>;
+ };
+
+ rtc@32 {
+ compatible = "microcrystal,rv8803";
+ reg = <0x32>;
+ };
+
+ sensor@4b {
+ compatible = "national,lm75b";
+ reg = <0x4b>;
+ };
+
+ eeprom@51 {
+ compatible = "atmel,24c32";
+ reg = <0x51>;
+ pagesize = <32>;
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+};
+
+/* M.2 B-key slot */
+&pcie0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie0>;
+ reset-gpio = <&gpio1 9 GPIO_ACTIVE_LOW>;
+ clocks = <&clk IMX8MQ_CLK_PCIE1_ROOT>,
+ <&clk IMX8MQ_CLK_PCIE1_AUX>,
+ <&clk IMX8MQ_CLK_PCIE1_PHY>,
+ <&pcie0_refclk>;
+ clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
+ status = "okay";
+};
+
+/* Intel Ethernet Controller I210/I211 */
+&pcie1 {
+ clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>,
+ <&clk IMX8MQ_CLK_PCIE2_AUX>,
+ <&clk IMX8MQ_CLK_PCIE2_PHY>,
+ <&pcie1_refclk>;
+ clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
+ fsl,max-link-speed = <1>;
+ status = "okay";
+};
+
+&pgc_gpu {
+ power-supply = <&sw1a_reg>;
+};
+
+&pgc_vpu {
+ power-supply = <&sw1c_reg>;
+};
+
+&qspi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qspi>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0>;
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+ m25p,fast-read;
+ spi-max-frequency = <50000000>;
+ };
+};
+
+&snvs_pwrkey {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ assigned-clocks = <&clk IMX8MQ_CLK_UART1>;
+ assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ assigned-clocks = <&clk IMX8MQ_CLK_UART2>;
+ assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ fsl,uart-has-rtscts;
+ assigned-clocks = <&clk IMX8MQ_CLK_UART3>;
+ assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>;
+ status = "okay";
+};
+
+&usb3_phy0 {
+ status = "okay";
+};
+
+&usb3_phy1 {
+ status = "okay";
+};
+
+&usb_dwc3_0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0>;
+ dr_mode = "otg";
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+ maximum-speed = "high-speed";
+ status = "okay";
+};
+
+&usb_dwc3_1 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usdhc1 {
+ assigned-clocks = <&clk IMX8MQ_CLK_USDHC1>;
+ assigned-clock-rates = <400000000>;
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ vqmmc-supply = <&sw4_reg>;
+ bus-width = <8>;
+ non-removable;
+ no-sd;
+ no-sdio;
+ status = "okay";
+};
+
+&usdhc2 {
+ assigned-clocks = <&clk IMX8MQ_CLK_USDHC2>;
+ assigned-clock-rates = <200000000>;
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+ bus-width = <4>;
+ cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>;
+ vmmc-supply = <&reg_usdhc2_vmmc>;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_NAND_CE1_B_GPIO3_IO2 0x19 /* TPM Reset */
+ MX8MQ_IOMUXC_NAND_CE3_B_GPIO3_IO4 0x19 /* USB2 Hub Reset */
+ >;
+ };
+
+ pinctrl_gpio: gpiogrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_NAND_CLE_GPIO3_IO5 0x19 /* GPIO0 */
+ MX8MQ_IOMUXC_NAND_RE_B_GPIO3_IO15 0x19 /* GPIO1 */
+ MX8MQ_IOMUXC_NAND_WE_B_GPIO3_IO17 0x19 /* GPIO2 */
+ MX8MQ_IOMUXC_NAND_WP_B_GPIO3_IO18 0x19 /* GPIO3 */
+ MX8MQ_IOMUXC_NAND_READY_B_GPIO3_IO16 0x19 /* GPIO4 */
+ MX8MQ_IOMUXC_NAND_DATA04_GPIO3_IO10 0x19 /* GPIO5 */
+ MX8MQ_IOMUXC_NAND_DATA05_GPIO3_IO11 0x19 /* GPIO6 */
+ MX8MQ_IOMUXC_NAND_DATA06_GPIO3_IO12 0x19 /* GPIO7 */
+ >;
+ };
+
+ pinctrl_pcie0: pcie0grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x16 /* PCIE_PERST */
+ MX8MQ_IOMUXC_UART4_TXD_GPIO5_IO29 0x16 /* W_DISABLE */
+ >;
+ };
+
+ pinctrl_reg_usdhc2: regusdhc2gpiogrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41
+ >;
+ };
+
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC 0x3
+ MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO 0x23
+ MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
+ MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
+ MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
+ MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
+ MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
+ MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
+ MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
+ MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
+ MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
+ MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
+ MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
+ MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
+ MX8MQ_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x16
+ MX8MQ_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x16
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x4000007f
+ MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x4000007f
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL 0x4000007f
+ MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA 0x4000007f
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL 0x4000007f
+ MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA 0x4000007f
+ >;
+ };
+
+ pinctrl_qspi: qspigrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x82
+ MX8MQ_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82
+ MX8MQ_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82
+ MX8MQ_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82
+ MX8MQ_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82
+ MX8MQ_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x19
+ MX8MQ_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x19
+ MX8MQ_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x19
+ >;
+ };
+
+ pinctrl_ecspi2_cs: ecspi2csgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x19
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX 0x49
+ MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x49
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX 0x49
+ MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX 0x49
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART3_TXD_UART3_DCE_TX 0x49
+ MX8MQ_IOMUXC_UART3_RXD_UART3_DCE_RX 0x49
+ MX8MQ_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B 0x49
+ MX8MQ_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B 0x49
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc3
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc3
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc3
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc3
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc3
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc3
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc3
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc3
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc3
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x83
+ MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1-100grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x8d
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xcd
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xcd
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xcd
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xcd
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xcd
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xcd
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xcd
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xcd
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xcd
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x8d
+ MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1-200grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x9f
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xdf
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xdf
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xdf
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xdf
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xdf
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xdf
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xdf
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xdf
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xdf
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x9f
+ MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12 0x41
+ MX8MQ_IOMUXC_SD2_WP_GPIO2_IO20 0x19
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x83
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc3
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc3
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc3
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc3
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc3
+ MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x8d
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xcd
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xcd
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xcd
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xcd
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xcd
+ MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x9f
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xdf
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xdf
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xdf
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xdf
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xdf
+ MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_usb0: usb0grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO12_USB1_OTG_PWR 0x19
+ MX8MQ_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x19
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
+ >;
+ };
+};
--
2.30.0

2021-03-08 08:36:44

by Shawn Guo

[permalink] [raw]
Subject: Re: [PATCH v4 0/2] add Kontron pITX-imx8m board

On Wed, Mar 03, 2021 at 10:10:01PM +0100, Heiko Thiery wrote:
> This patch series adds support for the Kontron pITX-imx8m board:
>
> https://www.kontron.com/products/boards-and-standard-form-factors/single-board-computer/pitx-imx8m.html
>
> Heiko Thiery (2):
> dt-bindings: arm: fsl: add Kontron pITX-imx8m board
> arm64: dts: fsl: add support for Kontron pitx-imx8m board

Applied both, thanks.

2021-03-08 20:14:02

by Rob Herring (Arm)

[permalink] [raw]
Subject: Re: [PATCH v4 1/2] dt-bindings: arm: fsl: add Kontron pITX-imx8m board

On Wed, 03 Mar 2021 22:10:03 +0100, Heiko Thiery wrote:
> Add the Kontron pITX-imx8m board.
>
> Signed-off-by: Heiko Thiery <[email protected]>
> Reviewed-by: Krzysztof Kozlowski <[email protected]>
> ---
> v2:
> - bring in correct alphabetical order
>
> v3:
> - no change
>
> v4:
> - no change
>
> Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
> 1 file changed, 1 insertion(+)
>

Acked-by: Rob Herring <[email protected]>