This fixed some problem identified in my last release. I made updates
based on comments from Christophe Leroy.
I added scripted updates to the defconfig file for mips and powerpc.
This is required in order to maintain the status quo for those platforms
which used the prior builtin command line system.
These were tested on all effected architectures.
Daniel Walker (7):
CMDLINE: add generic builtin command line
CMDLINE: drivers: of: ifdef out cmdline section
powerpc: convert config files to generic cmdline
CMDLINE: powerpc: convert to generic builtin command line
mips: convert config files to generic cmdline
CMDLINE: mips: convert to generic builtin command line
CMDLINE: x86: convert to generic builtin command line
arch/mips/Kconfig | 4 +-
arch/mips/Kconfig.debug | 44 ---------
arch/mips/configs/ar7_defconfig | 9 +-
arch/mips/configs/bcm47xx_defconfig | 8 +-
arch/mips/configs/bcm63xx_defconfig | 15 ++--
arch/mips/configs/bmips_be_defconfig | 11 +--
arch/mips/configs/bmips_stb_defconfig | 11 +--
arch/mips/configs/capcella_defconfig | 11 +--
arch/mips/configs/ci20_defconfig | 10 +--
arch/mips/configs/cu1000-neo_defconfig | 10 +--
arch/mips/configs/cu1830-neo_defconfig | 10 +--
arch/mips/configs/e55_defconfig | 4 +-
arch/mips/configs/generic_defconfig | 6 +-
arch/mips/configs/gpr_defconfig | 18 +---
arch/mips/configs/loongson3_defconfig | 13 +--
arch/mips/configs/mpc30x_defconfig | 7 +-
arch/mips/configs/tb0219_defconfig | 7 +-
arch/mips/configs/tb0226_defconfig | 7 +-
arch/mips/configs/tb0287_defconfig | 7 +-
arch/mips/configs/workpad_defconfig | 11 +--
arch/mips/kernel/setup.c | 36 +-------
arch/powerpc/Kconfig | 37 +-------
arch/powerpc/configs/44x/fsp2_defconfig | 33 ++++---
arch/powerpc/configs/44x/iss476-smp_defconfig | 25 +++---
arch/powerpc/configs/44x/warp_defconfig | 17 ++--
arch/powerpc/configs/holly_defconfig | 13 +--
arch/powerpc/configs/mvme5100_defconfig | 23 ++---
arch/powerpc/configs/skiroot_defconfig | 12 ++-
arch/powerpc/configs/storcenter_defconfig | 18 ++--
arch/powerpc/kernel/prom.c | 1 +
arch/powerpc/kernel/prom_init.c | 35 +++++---
arch/x86/Kconfig | 44 +--------
arch/x86/kernel/setup.c | 18 +---
drivers/firmware/efi/libstub/x86-stub.c | 2 +-
drivers/of/fdt.c | 12 +++
include/linux/cmdline.h | 89 +++++++++++++++++++
init/Kconfig | 68 ++++++++++++++
37 files changed, 321 insertions(+), 385 deletions(-)
create mode 100644 include/linux/cmdline.h
--
2.25.1
On 3/8/21 3:53 PM, Daniel Walker wrote:
> This fixed some problem identified in my last release. I made updates
> based on comments from Christophe Leroy.
>
> I added scripted updates to the defconfig file for mips and powerpc.
> This is required in order to maintain the status quo for those platforms
> which used the prior builtin command line system.
>
> These were tested on all effected architectures.
>
> Daniel Walker (7):
> CMDLINE: add generic builtin command line
> CMDLINE: drivers: of: ifdef out cmdline section
> powerpc: convert config files to generic cmdline
> CMDLINE: powerpc: convert to generic builtin command line
> mips: convert config files to generic cmdline
> CMDLINE: mips: convert to generic builtin command line
> CMDLINE: x86: convert to generic builtin command line
>
Hi Daniel,
These patches (1 - 7) should be sent as a Reply-to patch #0.
In .gitconfig, could you use
thread = true
or use --thread on the command line?
HTH.
thanks.
--
~Randy