The patch enables spread spectrum clocking (SSC) for MPU and LCD PLLs.
As reported by the TI spruh73x RM, SSC is only supported for the
DISP/LCD and MPU PLLs on am33xx device. SSC is not supported for DDR,
PER, and CORE PLLs.
Calculating the required values and setting the registers accordingly
was taken from the set_mpu_spreadspectrum routine contained in the
arch/arm/mach-omap2/am33xx/clock_am33xx.c file of the u-boot project.
In locked condition, DPLL output clock = CLKINP *[M/N]. In case of
SSC enabled, the AM335x reference manual explains that there is a
restriction of range of M values. Since the omap2_dpll_round_rate
routine attempts to select the minimum possible N, the value of M
obtained is not guaranteed to be within the range required. With the new
"ti,min-div" parameter it is possible to increase N and consequently M
to satisfy the constraint imposed by SSC.
Signed-off-by: Dario Binacchi <[email protected]>
---
Changes in v2:
- Move the DT changes to the previous patch in the series.
drivers/clk/ti/dpll.c | 41 +++++++++++++++++++
drivers/clk/ti/dpll3xxx.c | 85 +++++++++++++++++++++++++++++++++++++++
include/linux/clk/ti.h | 24 +++++++++++
3 files changed, 150 insertions(+)
diff --git a/drivers/clk/ti/dpll.c b/drivers/clk/ti/dpll.c
index d6f1ac5b53e1..2738417a47b7 100644
--- a/drivers/clk/ti/dpll.c
+++ b/drivers/clk/ti/dpll.c
@@ -290,7 +290,9 @@ static void __init of_ti_dpll_setup(struct device_node *node,
struct clk_init_data *init = NULL;
const char **parent_names = NULL;
struct dpll_data *dd = NULL;
+ int ssc_clk_index;
u8 dpll_mode = 0;
+ u32 min_div;
dd = kmemdup(ddt, sizeof(*dd), GFP_KERNEL);
clk_hw = kzalloc(sizeof(*clk_hw), GFP_KERNEL);
@@ -345,6 +347,27 @@ static void __init of_ti_dpll_setup(struct device_node *node,
if (dd->autoidle_mask) {
if (ti_clk_get_reg_addr(node, 3, &dd->autoidle_reg))
goto cleanup;
+
+ ssc_clk_index = 4;
+ } else {
+ ssc_clk_index = 3;
+ }
+
+ if (dd->ssc_deltam_int_mask && dd->ssc_deltam_frac_mask &&
+ dd->ssc_modfreq_mant_mask && dd->ssc_modfreq_exp_mask) {
+ if (ti_clk_get_reg_addr(node, ssc_clk_index++,
+ &dd->ssc_deltam_reg))
+ goto cleanup;
+
+ if (ti_clk_get_reg_addr(node, ssc_clk_index++,
+ &dd->ssc_modfreq_reg))
+ goto cleanup;
+
+ of_property_read_u32(node, "ti,ssc-modfreq", &dd->ssc_modfreq);
+ of_property_read_u32(node, "ti,ssc-deltam", &dd->ssc_deltam);
+ if (of_property_read_bool(node, "ti,ssc-downspread"))
+ dd->ssc_downspread = 1;
+
}
if (of_property_read_bool(node, "ti,low-power-stop"))
@@ -356,6 +379,10 @@ static void __init of_ti_dpll_setup(struct device_node *node,
if (of_property_read_bool(node, "ti,lock"))
dpll_mode |= 1 << DPLL_LOCKED;
+ if (!of_property_read_u32(node, "ti,min-div", &min_div) &&
+ min_div > dd->min_divider)
+ dd->min_divider = min_div;
+
if (dpll_mode)
dd->modes = dpll_mode;
@@ -585,8 +612,15 @@ static void __init of_ti_am3_no_gate_dpll_setup(struct device_node *node)
const struct dpll_data dd = {
.idlest_mask = 0x1,
.enable_mask = 0x7,
+ .ssc_enable_mask = 0x1 << 12,
+ .ssc_ack_mask = 0x1 << 13,
+ .ssc_downspread_mask = 0x1 << 14,
.mult_mask = 0x7ff << 8,
.div1_mask = 0x7f,
+ .ssc_deltam_int_mask = 0x3 << 18,
+ .ssc_deltam_frac_mask = 0x3ffff,
+ .ssc_modfreq_mant_mask = 0x7f,
+ .ssc_modfreq_exp_mask = 0x7 << 8,
.max_multiplier = 2047,
.max_divider = 128,
.min_divider = 1,
@@ -645,8 +679,15 @@ static void __init of_ti_am3_dpll_setup(struct device_node *node)
const struct dpll_data dd = {
.idlest_mask = 0x1,
.enable_mask = 0x7,
+ .ssc_enable_mask = 0x1 << 12,
+ .ssc_ack_mask = 0x1 << 13,
+ .ssc_downspread_mask = 0x1 << 14,
.mult_mask = 0x7ff << 8,
.div1_mask = 0x7f,
+ .ssc_deltam_int_mask = 0x3 << 18,
+ .ssc_deltam_frac_mask = 0x3ffff,
+ .ssc_modfreq_mant_mask = 0x7f,
+ .ssc_modfreq_exp_mask = 0x7 << 8,
.max_multiplier = 2047,
.max_divider = 128,
.min_divider = 1,
diff --git a/drivers/clk/ti/dpll3xxx.c b/drivers/clk/ti/dpll3xxx.c
index 94d5b5fe9a2b..e32b3515f9e7 100644
--- a/drivers/clk/ti/dpll3xxx.c
+++ b/drivers/clk/ti/dpll3xxx.c
@@ -291,6 +291,88 @@ static void _lookup_sddiv(struct clk_hw_omap *clk, u8 *sd_div, u16 m, u8 n)
*sd_div = sd;
}
+/**
+ * omap3_noncore_dpll_ssc_program - set spread-spectrum clocking registers
+ * @clk: struct clk * of DPLL to set
+ *
+ * Enable the DPLL spread spectrum clocking if frequency modulation and
+ * frequency spreading have been set, otherwise disable it.
+ */
+static void omap3_noncore_dpll_ssc_program(struct clk_hw_omap *clk)
+{
+ struct dpll_data *dd = clk->dpll_data;
+ unsigned long ref_rate;
+ u32 v, ctrl, mod_freq_divider, exponent, mantissa;
+ u32 deltam_step, deltam_ceil;
+
+ ctrl = ti_clk_ll_ops->clk_readl(&dd->control_reg);
+
+ if (dd->ssc_modfreq && dd->ssc_deltam) {
+ ctrl |= dd->ssc_enable_mask;
+
+ if (dd->ssc_downspread)
+ ctrl |= dd->ssc_downspread_mask;
+ else
+ ctrl &= ~dd->ssc_downspread_mask;
+
+ ref_rate = clk_hw_get_rate(dd->clk_ref);
+ mod_freq_divider =
+ (ref_rate / dd->last_rounded_n) / (4 * dd->ssc_modfreq);
+ if (dd->ssc_modfreq > (ref_rate / 70))
+ pr_warn("clock: SSC modulation frequency of DPLL %s greater than %ld\n",
+ __clk_get_name(clk->hw.clk), ref_rate / 70);
+
+ exponent = 0;
+ mantissa = mod_freq_divider;
+ while ((mantissa > 127) && (exponent < 7)) {
+ exponent++;
+ mantissa /= 2;
+ }
+ if (mantissa > 127)
+ mantissa = 127;
+
+ v = ti_clk_ll_ops->clk_readl(&dd->ssc_modfreq_reg);
+ v &= ~(dd->ssc_modfreq_mant_mask | dd->ssc_modfreq_exp_mask);
+ v |= mantissa << __ffs(dd->ssc_modfreq_mant_mask);
+ v |= exponent << __ffs(dd->ssc_modfreq_exp_mask);
+ ti_clk_ll_ops->clk_writel(v, &dd->ssc_modfreq_reg);
+
+ deltam_step = dd->last_rounded_m * dd->ssc_deltam;
+ deltam_step /= 10;
+ if (dd->ssc_downspread)
+ deltam_step /= 2;
+
+ deltam_step <<= __ffs(dd->ssc_deltam_int_mask);
+ deltam_step /= 100;
+ deltam_step /= mod_freq_divider;
+ if (deltam_step > 0xFFFFF)
+ deltam_step = 0xFFFFF;
+
+ deltam_ceil = (deltam_step & dd->ssc_deltam_int_mask) >>
+ __ffs(dd->ssc_deltam_int_mask);
+ if (deltam_step & dd->ssc_deltam_frac_mask)
+ deltam_ceil++;
+
+ if ((dd->ssc_downspread &&
+ ((dd->last_rounded_m - (2 * deltam_ceil)) < 20 ||
+ dd->last_rounded_m > 2045)) ||
+ ((dd->last_rounded_m - deltam_ceil) < 20 ||
+ (dd->last_rounded_m + deltam_ceil) > 2045))
+ pr_warn("clock: SSC multiplier of DPLL %s is out of range\n",
+ __clk_get_name(clk->hw.clk));
+
+ v = ti_clk_ll_ops->clk_readl(&dd->ssc_deltam_reg);
+ v &= ~(dd->ssc_deltam_int_mask | dd->ssc_deltam_frac_mask);
+ v |= deltam_step << __ffs(dd->ssc_deltam_int_mask |
+ dd->ssc_deltam_frac_mask);
+ ti_clk_ll_ops->clk_writel(v, &dd->ssc_deltam_reg);
+ } else {
+ ctrl &= ~dd->ssc_enable_mask;
+ }
+
+ ti_clk_ll_ops->clk_writel(ctrl, &dd->control_reg);
+}
+
/**
* omap3_noncore_dpll_program - set non-core DPLL M,N values directly
* @clk: struct clk * of DPLL to set
@@ -390,6 +472,9 @@ static int omap3_noncore_dpll_program(struct clk_hw_omap *clk, u16 freqsel)
ti_clk_ll_ops->clk_writel(v, &dd->control_reg);
}
+ if (dd->ssc_enable_mask)
+ omap3_noncore_dpll_ssc_program(clk);
+
/* We let the clock framework set the other output dividers later */
/* REVISIT: Set ramp-up delay? */
diff --git a/include/linux/clk/ti.h b/include/linux/clk/ti.h
index c62f6fa6763d..cba093de62d8 100644
--- a/include/linux/clk/ti.h
+++ b/include/linux/clk/ti.h
@@ -63,6 +63,18 @@ struct clk_omap_reg {
* @auto_recal_bit: bitshift of the driftguard enable bit in @control_reg
* @recal_en_bit: bitshift of the PRM_IRQENABLE_* bit for recalibration IRQs
* @recal_st_bit: bitshift of the PRM_IRQSTATUS_* bit for recalibration IRQs
+ * @ssc_deltam_reg: register containing the DPLL SSC frequency spreading
+ * @ssc_modfreq_reg: register containing the DPLL SSC modulation frequency
+ * @ssc_modfreq_mant_mask: mask of the mantissa component in @ssc_modfreq_reg
+ * @ssc_modfreq_exp_mask: mask of the exponent component in @ssc_modfreq_reg
+ * @ssc_enable_mask: mask of the DPLL SSC enable bit in @control_reg
+ * @ssc_ack_mask: mask of the DPLL SSC turned on/off bit in @control_reg
+ * @ssc_downspread_mask: mask of the DPLL SSC low frequency only bit in
+ * @control_reg
+ * @ssc_modfreq: the DPLL SSC frequency modulation in kHz
+ * @ssc_deltam: the DPLL SSC frequency spreading in permille (10th of percent)
+ * @ssc_downspread: require the only low frequency spread of the DPLL in SSC
+ * mode
* @flags: DPLL type/features (see below)
*
* Possible values for @flags:
@@ -110,6 +122,18 @@ struct dpll_data {
u8 auto_recal_bit;
u8 recal_en_bit;
u8 recal_st_bit;
+ struct clk_omap_reg ssc_deltam_reg;
+ struct clk_omap_reg ssc_modfreq_reg;
+ u32 ssc_deltam_int_mask;
+ u32 ssc_deltam_frac_mask;
+ u32 ssc_modfreq_mant_mask;
+ u32 ssc_modfreq_exp_mask;
+ u32 ssc_enable_mask;
+ u32 ssc_ack_mask;
+ u32 ssc_downspread_mask;
+ u32 ssc_modfreq;
+ u32 ssc_deltam;
+ u8 ssc_downspread;
u8 flags;
};
--
2.17.1