2021-07-02 03:41:05

by Wesley Sheng

[permalink] [raw]
Subject: [PATCH v2] Documentation: PCI: pci-error-recovery: swap sequence between MMIO Enabled and Link Reset

Reset_link() callback function (named with reset_subordinates()
in pcie_do_recovery() function) was called before mmio_enabled(),
so exchange the sequence between step 2 MMIO Enabled and step 3
Link Reset accordingly.

Signed-off-by: Wesley Sheng <[email protected]>
---
Documentation/PCI/pci-error-recovery.rst | 25 ++++++++++++------------
1 file changed, 13 insertions(+), 12 deletions(-)

diff --git a/Documentation/PCI/pci-error-recovery.rst b/Documentation/PCI/pci-error-recovery.rst
index 187f43a03200..0e2f3f77bf0a 100644
--- a/Documentation/PCI/pci-error-recovery.rst
+++ b/Documentation/PCI/pci-error-recovery.rst
@@ -157,7 +157,7 @@ drivers.
If all drivers on the segment/slot return PCI_ERS_RESULT_CAN_RECOVER,
then the platform should re-enable IOs on the slot (or do nothing in
particular, if the platform doesn't isolate slots), and recovery
-proceeds to STEP 2 (MMIO Enable).
+proceeds to STEP 3 (MMIO Enable).

If any driver requested a slot reset (by returning PCI_ERS_RESULT_NEED_RESET),
then recovery proceeds to STEP 4 (Slot Reset).
@@ -184,7 +184,14 @@ is STEP 6 (Permanent Failure).
and prints an error to syslog. A reboot is then required to
get the device working again.

-STEP 2: MMIO Enabled
+STEP 2: Link Reset
+------------------
+The platform resets the link. This is a PCI-Express specific step
+and is done whenever a fatal error has been detected that can be
+"solved" by resetting the link.
+
+
+STEP 3: MMIO Enabled
--------------------
The platform re-enables MMIO to the device (but typically not the
DMA), and then calls the mmio_enabled() callback on all affected
@@ -197,8 +204,8 @@ information, if any, and eventually do things like trigger a device local
reset or some such, but not restart operations. This callback is made if
all drivers on a segment agree that they can try to recover and if no automatic
link reset was performed by the HW. If the platform can't just re-enable IOs
-without a slot reset or a link reset, it will not call this callback, and
-instead will have gone directly to STEP 3 (Link Reset) or STEP 4 (Slot Reset)
+without a slot reset, it will not call this callback, and
+instead will have gone directly to STEP 4 (Slot Reset)

.. note::

@@ -210,7 +217,7 @@ instead will have gone directly to STEP 3 (Link Reset) or STEP 4 (Slot Reset)
such an error might cause IOs to be re-blocked for the whole
segment, and thus invalidate the recovery that other devices
on the same segment might have done, forcing the whole segment
- into one of the next states, that is, link reset or slot reset.
+ into the next states, that is, slot reset.

The driver should return one of the following result codes:
- PCI_ERS_RESULT_RECOVERED
@@ -233,17 +240,11 @@ The driver should return one of the following result codes:

The next step taken depends on the results returned by the drivers.
If all drivers returned PCI_ERS_RESULT_RECOVERED, then the platform
-proceeds to either STEP3 (Link Reset) or to STEP 5 (Resume Operations).
+proceeds to STEP 5 (Resume Operations).

If any driver returned PCI_ERS_RESULT_NEED_RESET, then the platform
proceeds to STEP 4 (Slot Reset)

-STEP 3: Link Reset
-------------------
-The platform resets the link. This is a PCI-Express specific step
-and is done whenever a fatal error has been detected that can be
-"solved" by resetting the link.
-
STEP 4: Slot Reset
------------------

--
2.25.1