This allows to keep PHY link up and prevents any channel resets during
the host load. On BMC it prevents channel reconfiguration:
eth1: NCSI: No channel with link found, configuring channel 0
which brings problem with BMC accessibility.
It is KEEP_PHY_LINK_UP option(Veto bit) in i210 datasheet which
blocks PHY reset and power state changes.
Signed-off-by: Ivan Mikhaylov <[email protected]>
---
net/ncsi/Kconfig | 6 ++++++
net/ncsi/internal.h | 5 +++++
net/ncsi/ncsi-manage.c | 48 ++++++++++++++++++++++++++++++++++++++++++
3 files changed, 59 insertions(+)
diff --git a/net/ncsi/Kconfig b/net/ncsi/Kconfig
index 93309081f5a4..ea1dd32b6b1f 100644
--- a/net/ncsi/Kconfig
+++ b/net/ncsi/Kconfig
@@ -17,3 +17,9 @@ config NCSI_OEM_CMD_GET_MAC
help
This allows to get MAC address from NCSI firmware and set them back to
controller.
+config NCSI_OEM_CMD_KEEP_PHY
+ bool "Keep PHY Link up"
+ depends on NET_NCSI
+ help
+ This allows to keep PHY link up and prevents any channel resets during
+ the host load.
diff --git a/net/ncsi/internal.h b/net/ncsi/internal.h
index 49031f804276..0a232f3eb343 100644
--- a/net/ncsi/internal.h
+++ b/net/ncsi/internal.h
@@ -78,6 +78,9 @@ enum {
/* OEM Vendor Manufacture ID */
#define NCSI_OEM_MFR_MLX_ID 0x8119
#define NCSI_OEM_MFR_BCM_ID 0x113d
+#define NCSI_OEM_MFR_INL_ID 0x157
+/* Intel specific OEM command */
+#define NCSI_OEM_INL_CMD_KEEP_PHY 0x20 /* CMD ID for Keep PHY up */
/* Broadcom specific OEM Command */
#define NCSI_OEM_BCM_CMD_GMA 0x01 /* CMD ID for Get MAC */
/* Mellanox specific OEM Command */
@@ -86,6 +89,7 @@ enum {
#define NCSI_OEM_MLX_CMD_SMAF 0x01 /* CMD ID for Set MC Affinity */
#define NCSI_OEM_MLX_CMD_SMAF_PARAM 0x07 /* Parameter for SMAF */
/* OEM Command payload lengths*/
+#define NCSI_OEM_INL_CMD_KEEP_PHY_LEN 7
#define NCSI_OEM_BCM_CMD_GMA_LEN 12
#define NCSI_OEM_MLX_CMD_GMA_LEN 8
#define NCSI_OEM_MLX_CMD_SMAF_LEN 60
@@ -270,6 +274,7 @@ enum {
ncsi_dev_state_probe_channel,
ncsi_dev_state_probe_mlx_gma,
ncsi_dev_state_probe_mlx_smaf,
+ ncsi_dev_state_probe_keep_phy,
ncsi_dev_state_probe_cis,
ncsi_dev_state_probe_gvi,
ncsi_dev_state_probe_gc,
diff --git a/net/ncsi/ncsi-manage.c b/net/ncsi/ncsi-manage.c
index ffff8da707b8..d78cca2a2b26 100644
--- a/net/ncsi/ncsi-manage.c
+++ b/net/ncsi/ncsi-manage.c
@@ -689,6 +689,37 @@ static int set_one_vid(struct ncsi_dev_priv *ndp, struct ncsi_channel *nc,
return 0;
}
+#if IS_ENABLED(CONFIG_NCSI_OEM_CMD_KEEP_PHY)
+
+static int ncsi_oem_keep_phy_inl(struct ncsi_cmd_arg *nca)
+{
+ unsigned char data[NCSI_OEM_INL_CMD_KEEP_PHY_LEN];
+ int ret = 0;
+
+ nca->payload = NCSI_OEM_INL_CMD_KEEP_PHY_LEN;
+
+ memset(data, 0, NCSI_OEM_INL_CMD_KEEP_PHY_LEN);
+ *(unsigned int *)data = ntohl(NCSI_OEM_MFR_INL_ID);
+
+ /* Predefined data */
+ data[4] = NCSI_OEM_INL_CMD_KEEP_PHY;
+ data[5] = 0x0;
+
+ /* PHY Link up attribute */
+ data[6] = 0x1;
+
+ nca->data = data;
+
+ ret = ncsi_xmit_cmd(nca);
+ if (ret)
+ netdev_err(nca->ndp->ndev.dev,
+ "NCSI: Failed to transmit cmd 0x%x during configure\n",
+ nca->type);
+ return ret;
+}
+
+#endif
+
#if IS_ENABLED(CONFIG_NCSI_OEM_CMD_GET_MAC)
/* NCSI OEM Command APIs */
@@ -1350,8 +1381,25 @@ static void ncsi_probe_channel(struct ncsi_dev_priv *ndp)
ndp->mlx_multi_host)
nd->state = ncsi_dev_state_probe_mlx_gma;
+ if (IS_ENABLED(CONFIG_NCSI_OEM_CMD_KEEP_PHY))
+ nd->state = ncsi_dev_state_probe_keep_phy;
+
schedule_work(&ndp->work);
break;
+#if IS_ENABLED(CONFIG_NCSI_OEM_CMD_KEEP_PHY)
+ case ncsi_dev_state_probe_keep_phy:
+ ndp->pending_req_num = 1;
+
+ nca.type = NCSI_PKT_CMD_OEM;
+ nca.package = ndp->active_package->id;
+ nca.channel = 0;
+ ret = ncsi_oem_keep_phy_inl(&nca);
+ if (ret)
+ goto error;
+
+ nd->state = ncsi_dev_state_probe_cis;
+ break;
+#endif /* CONFIG_NCSI_OEM_CMD_KEEP_PHY */
#if IS_ENABLED(CONFIG_NCSI_OEM_CMD_GET_MAC)
case ncsi_dev_state_probe_mlx_gma:
ndp->pending_req_num = 1;
--
2.31.1