Gpiolib core code has been updated to support setting
friendly names through properly 'gpio-line-names'.
Instead of redefine behaviour here to skip the core
to be executed, just properly assign the desired offset
per bank to get in the core the expected behaviour.
Reviewed-by: Andy Shevchenko <[email protected]>
Acked-by: Gregory Fong <[email protected]>
Signed-off-by: Sergio Paracuellos <[email protected]>
---
drivers/gpio/gpio-brcmstb.c | 45 +------------------------------------
1 file changed, 1 insertion(+), 44 deletions(-)
diff --git a/drivers/gpio/gpio-brcmstb.c b/drivers/gpio/gpio-brcmstb.c
index fcfc1a1f1a5c..a7275159052e 100644
--- a/drivers/gpio/gpio-brcmstb.c
+++ b/drivers/gpio/gpio-brcmstb.c
@@ -603,49 +603,6 @@ static const struct dev_pm_ops brcmstb_gpio_pm_ops = {
.resume_noirq = brcmstb_gpio_resume,
};
-static void brcmstb_gpio_set_names(struct device *dev,
- struct brcmstb_gpio_bank *bank)
-{
- struct device_node *np = dev->of_node;
- const char **names;
- int nstrings, base;
- unsigned int i;
-
- base = bank->id * MAX_GPIO_PER_BANK;
-
- nstrings = of_property_count_strings(np, "gpio-line-names");
- if (nstrings <= base)
- /* Line names not present */
- return;
-
- names = devm_kcalloc(dev, MAX_GPIO_PER_BANK, sizeof(*names),
- GFP_KERNEL);
- if (!names)
- return;
-
- /*
- * Make sure to not index beyond the end of the number of descriptors
- * of the GPIO device.
- */
- for (i = 0; i < bank->width; i++) {
- const char *name;
- int ret;
-
- ret = of_property_read_string_index(np, "gpio-line-names",
- base + i, &name);
- if (ret) {
- if (ret != -ENODATA)
- dev_err(dev, "unable to name line %d: %d\n",
- base + i, ret);
- break;
- }
- if (*name)
- names[i] = name;
- }
-
- bank->gc.names = names;
-}
-
static int brcmstb_gpio_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
@@ -759,6 +716,7 @@ static int brcmstb_gpio_probe(struct platform_device *pdev)
gc->of_xlate = brcmstb_gpio_of_xlate;
/* not all ngpio lines are valid, will use bank width later */
gc->ngpio = MAX_GPIO_PER_BANK;
+ gc->offset = bank->id * MAX_GPIO_PER_BANK;
if (priv->parent_irq > 0)
gc->to_irq = brcmstb_gpio_to_irq;
@@ -769,7 +727,6 @@ static int brcmstb_gpio_probe(struct platform_device *pdev)
need_wakeup_event |= !!__brcmstb_gpio_get_active_irqs(bank);
gc->write_reg(reg_base + GIO_MASK(bank->id), 0);
- brcmstb_gpio_set_names(dev, bank);
err = gpiochip_add_data(gc, bank);
if (err) {
dev_err(dev, "Could not add gpiochip for bank %d\n",
--
2.25.1
On Tue, Jul 27, 2021 at 5:48 PM Sergio Paracuellos
<[email protected]> wrote:
>
> Gpiolib core code has been updated to support setting
> friendly names through properly 'gpio-line-names'.
> Instead of redefine behaviour here to skip the core
> to be executed, just properly assign the desired offset
> per bank to get in the core the expected behaviour.
Since it will be a v3, reflow commit messages to occupy a little bit
more available space (per line). Something ~72-75 characters per line
is good balance.
--
With Best Regards,
Andy Shevchenko
On Tue, Jul 27, 2021 at 5:07 PM Andy Shevchenko
<[email protected]> wrote:
>
> On Tue, Jul 27, 2021 at 5:48 PM Sergio Paracuellos
> <[email protected]> wrote:
> >
> > Gpiolib core code has been updated to support setting
> > friendly names through properly 'gpio-line-names'.
> > Instead of redefine behaviour here to skip the core
> > to be executed, just properly assign the desired offset
> > per bank to get in the core the expected behaviour.
>
> Since it will be a v3, reflow commit messages to occupy a little bit
> more available space (per line). Something ~72-75 characters per line
> is good balance.
Sure.
Thanks,
Sergio Paracuellos
>
> --
> With Best Regards,
> Andy Shevchenko