From: Tao Ren <[email protected]>
The patch series introuces 3 new Facebook AST2600 Network BMC platforms.
Patch #1 adds dtsi file to describe the fixed flash layout of 128MB mtd
device. The flash layout is used by all the 3 AST2600 BMC as well as
Wedge400 (AST2500).
Patch #2 simplies Wedge400 dts by including the flash layout dtsi.
Patch #3 adds common dtsi which is included by all the new Facebook
AST2600 Network BMC platforms.
Patch #4 adds the device tree for Facebook Cloudripper (AST2600) BMC.
Patch #5 adds the device tree for Facebook Elbert (AST2600) BMC.
Patch #6 adds the device tree for Facebook Fuji (AST2600) BMC.
Tao Ren (6):
ARM: dts: Add Facebook BMC 128MB flash layout
ARM: dts: aspeed: wedge400: Use common flash layout
ARM: dts: aspeed: Common dtsi for Facebook AST2600 Network BMCs
ARM: dts: aspeed: Add Facebook Cloudripper (AST2600) BMC
ARM: dts: aspeed: Add Facebook Elbert (AST2600) BMC
ARM: dts: aspeed: Add Facebook Fuji (AST2600) BMC
arch/arm/boot/dts/Makefile | 3 +
.../dts/aspeed-bmc-facebook-cloudripper.dts | 564 ++++++++
.../boot/dts/aspeed-bmc-facebook-elbert.dts | 185 +++
.../arm/boot/dts/aspeed-bmc-facebook-fuji.dts | 1276 +++++++++++++++++
.../boot/dts/aspeed-bmc-facebook-wedge400.dts | 48 +-
.../dts/ast2600-facebook-netbmc-common.dtsi | 176 +++
.../dts/facebook-bmc-flash-layout-128.dtsi | 60 +
7 files changed, 2265 insertions(+), 47 deletions(-)
create mode 100644 arch/arm/boot/dts/aspeed-bmc-facebook-cloudripper.dts
create mode 100644 arch/arm/boot/dts/aspeed-bmc-facebook-elbert.dts
create mode 100644 arch/arm/boot/dts/aspeed-bmc-facebook-fuji.dts
create mode 100644 arch/arm/boot/dts/ast2600-facebook-netbmc-common.dtsi
create mode 100644 arch/arm/boot/dts/facebook-bmc-flash-layout-128.dtsi
--
2.17.1
From: Tao Ren <[email protected]>
This is the layout used by Facebook BMC systems. It describes the fixed
flash layout of a 128MB mtd device.
Signed-off-by: Tao Ren <[email protected]>
---
.../dts/facebook-bmc-flash-layout-128.dtsi | 60 +++++++++++++++++++
1 file changed, 60 insertions(+)
create mode 100644 arch/arm/boot/dts/facebook-bmc-flash-layout-128.dtsi
diff --git a/arch/arm/boot/dts/facebook-bmc-flash-layout-128.dtsi b/arch/arm/boot/dts/facebook-bmc-flash-layout-128.dtsi
new file mode 100644
index 000000000000..7f3652dea550
--- /dev/null
+++ b/arch/arm/boot/dts/facebook-bmc-flash-layout-128.dtsi
@@ -0,0 +1,60 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2020 Facebook Inc.
+
+partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /*
+ * u-boot partition: 896KB.
+ */
+ u-boot@0 {
+ reg = <0x0 0xe0000>;
+ label = "u-boot";
+ };
+
+ /*
+ * u-boot environment variables: 64KB.
+ */
+ u-boot-env@e0000 {
+ reg = <0xe0000 0x10000>;
+ label = "env";
+ };
+
+ /*
+ * image metadata partition (64KB), used by Facebook internal
+ * tools.
+ */
+ image-meta@f0000 {
+ reg = <0xf0000 0x10000>;
+ label = "meta";
+ };
+
+ /*
+ * FIT image: 119 MB.
+ */
+ fit@100000 {
+ reg = <0x100000 0x7700000>;
+ label = "fit";
+ };
+
+ /*
+ * "data0" partition (8MB) is used by Facebook BMC platforms as
+ * persistent data store.
+ */
+ data0@7800000 {
+ reg = <0x7800000 0x800000>;
+ label = "data0";
+ };
+
+ /*
+ * Although the master partition can be created by enabling
+ * MTD_PARTITIONED_MASTER option, below "flash0" partition is
+ * explicitly created to avoid breaking legacy applications.
+ */
+ flash0@0 {
+ reg = <0x0 0x8000000>;
+ label = "flash0";
+ };
+};
--
2.17.1
From: Tao Ren <[email protected]>
This common descirption is included by all Facebook AST2600 Network BMC
platforms to minimize duplicated device entries across Facebook Network
BMC device trees.
Signed-off-by: Tao Ren <[email protected]>
---
.../dts/ast2600-facebook-netbmc-common.dtsi | 176 ++++++++++++++++++
1 file changed, 176 insertions(+)
create mode 100644 arch/arm/boot/dts/ast2600-facebook-netbmc-common.dtsi
diff --git a/arch/arm/boot/dts/ast2600-facebook-netbmc-common.dtsi b/arch/arm/boot/dts/ast2600-facebook-netbmc-common.dtsi
new file mode 100644
index 000000000000..e3b350c824d2
--- /dev/null
+++ b/arch/arm/boot/dts/ast2600-facebook-netbmc-common.dtsi
@@ -0,0 +1,176 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2020 Facebook Inc.
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+ aliases {
+ mmc0 = &emmc;
+ spi1 = &spi1;
+ spi2 = &spi_gpio;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,9600n8 root=/dev/ram rw vmalloc=640M";
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x80000000>;
+ };
+
+ /*
+ * GPIO-based SPI Master is required to access SPI TPM, because
+ * full-duplex SPI transactions are not supported by ASPEED SPI
+ * Controllers.
+ */
+ spi_gpio: spi-gpio {
+ status = "okay";
+ compatible = "spi-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio-sck = <&gpio0 ASPEED_GPIO(X, 3) GPIO_ACTIVE_HIGH>;
+ gpio-mosi = <&gpio0 ASPEED_GPIO(X, 4) GPIO_ACTIVE_HIGH>;
+ gpio-miso = <&gpio0 ASPEED_GPIO(X, 5) GPIO_ACTIVE_HIGH>;
+
+ tpmdev@0 {
+ compatible = "tcg,tpm_tis-spi";
+ spi-max-frequency = <33000000>;
+ reg = <0>;
+ };
+ };
+};
+
+&fmc {
+ status = "okay";
+
+ flash@0 {
+ status = "okay";
+ m25p,fast-read;
+ label = "spi0.0";
+
+#include "facebook-bmc-flash-layout-128.dtsi"
+ };
+
+ flash@1 {
+ status = "okay";
+ m25p,fast-read;
+ label = "spi0.1";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ flash1@0 {
+ reg = <0x0 0x8000000>;
+ label = "flash1";
+ };
+ };
+ };
+};
+
+&spi1 {
+ status = "okay";
+};
+
+&mac3 {
+ status = "okay";
+ phy-mode = "rgmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rgmii4_default>;
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart5 {
+ status = "okay";
+};
+
+&wdt1 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+&i2c2 {
+ status = "okay";
+};
+
+&i2c3 {
+ status = "okay";
+};
+
+&i2c4 {
+ status = "okay";
+};
+
+&i2c5 {
+ status = "okay";
+};
+
+&i2c6 {
+ status = "okay";
+};
+
+&i2c7 {
+ status = "okay";
+};
+
+&i2c8 {
+ status = "okay";
+};
+
+&i2c9 {
+ status = "okay";
+};
+
+&i2c10 {
+ status = "okay";
+};
+
+&i2c12 {
+ status = "okay";
+};
+
+&i2c13 {
+ status = "okay";
+};
+
+&i2c15 {
+ status = "okay";
+};
+
+&vhub {
+ status = "okay";
+};
+
+&emmc_controller {
+ status = "okay";
+};
+
+&emmc {
+ status = "okay";
+
+ non-removable;
+ max-frequency = <25000000>;
+ bus-width = <4>;
+};
+
+&rtc {
+ status = "okay";
+};
--
2.17.1
From: Tao Ren <[email protected]>
Add initial version of device tree for Facebook Cloudripper (AST2600) BMC.
Signed-off-by: Tao Ren <[email protected]>
---
arch/arm/boot/dts/Makefile | 1 +
.../dts/aspeed-bmc-facebook-cloudripper.dts | 564 ++++++++++++++++++
2 files changed, 565 insertions(+)
create mode 100644 arch/arm/boot/dts/aspeed-bmc-facebook-cloudripper.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 90aed2c2959a..74c760038f28 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1409,6 +1409,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
aspeed-bmc-arm-stardragon4800-rep2.dtb \
aspeed-bmc-asrock-e3c246d4i.dtb \
aspeed-bmc-bytedance-g220a.dtb \
+ aspeed-bmc-facebook-cloudripper.dtb \
aspeed-bmc-facebook-cmm.dtb \
aspeed-bmc-facebook-galaxy100.dtb \
aspeed-bmc-facebook-minipack.dtb \
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-cloudripper.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-cloudripper.dts
new file mode 100644
index 000000000000..1a9808ba8107
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-facebook-cloudripper.dts
@@ -0,0 +1,564 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2020 Facebook Inc.
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include "ast2600-facebook-netbmc-common.dtsi"
+
+/ {
+ model = "Facebook Cloudripper BMC";
+ compatible = "facebook,cloudripper-bmc", "aspeed,ast2600";
+
+ aliases {
+ /*
+ * PCA9548 (1-0070) provides 8 channels connecting to
+ * SMB (Switch Main Board).
+ */
+ i2c16 = &imux16;
+ i2c17 = &imux17;
+ i2c18 = &imux18;
+ i2c19 = &imux19;
+ i2c20 = &imux20;
+ i2c21 = &imux21;
+ i2c22 = &imux22;
+ i2c23 = &imux23;
+
+ /*
+ * PCA9548 (2-0070) provides 8 channels connecting to
+ * SCM (System Controller Module).
+ */
+ i2c24 = &imux24;
+ i2c25 = &imux25;
+ i2c26 = &imux26;
+ i2c27 = &imux27;
+ i2c28 = &imux28;
+ i2c29 = &imux29;
+ i2c30 = &imux30;
+ i2c31 = &imux31;
+
+ /*
+ * PCA9548 (3-0070) provides 8 channels connecting to
+ * SMB (Switch Main Board).
+ */
+ i2c32 = &imux32;
+ i2c33 = &imux33;
+ i2c34 = &imux34;
+ i2c35 = &imux35;
+ i2c36 = &imux36;
+ i2c37 = &imux37;
+ i2c38 = &imux38;
+ i2c39 = &imux39;
+
+ /*
+ * PCA9548 (8-0070) provides 8 channels connecting to
+ * PDB (Power Delivery Board).
+ */
+ i2c40 = &imux40;
+ i2c41 = &imux41;
+ i2c42 = &imux42;
+ i2c43 = &imux43;
+ i2c44 = &imux44;
+ i2c45 = &imux45;
+ i2c46 = &imux46;
+ i2c47 = &imux47;
+
+ /*
+ * PCA9548 (15-0076) provides 8 channels connecting to
+ * FCM (Fan Controller Module).
+ */
+ i2c48 = &imux48;
+ i2c49 = &imux49;
+ i2c50 = &imux50;
+ i2c51 = &imux51;
+ i2c52 = &imux52;
+ i2c53 = &imux53;
+ i2c54 = &imux54;
+ i2c55 = &imux55;
+ };
+
+ spi_gpio: spi-gpio {
+ num-chipselects = <2>;
+ cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>,
+ <&gpio0 ASPEED_GPIO(X, 1) GPIO_ACTIVE_HIGH>;
+
+ eeprom@1 {
+ compatible = "atmel,at93c46d";
+ spi-max-frequency = <250000>;
+ data-size = <16>;
+ spi-cs-high;
+ reg = <1>;
+ };
+ };
+};
+
+&spi1 {
+ status = "okay";
+
+ /*
+ * Customize spi1 flash memory size to 16MB (maximum flash size on
+ * the bus) to save vmalloc space.
+ */
+ reg = < 0x1e630000 0xc4
+ 0x30000000 0x1000000 >;
+
+ flash@0 {
+ status = "okay";
+ m25p,fast-read;
+ label = "spi1.0";
+ spi-max-frequency = <5000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ flash1@0 {
+ reg = <0x0 0x1000000>;
+ label = "system-flash";
+ };
+ };
+ };
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&mdio1 {
+ status = "okay";
+};
+
+&mdio3 {
+ status = "okay";
+
+ ethphy1: ethernet-phy@13 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0x0d>;
+ };
+};
+
+&mac3 {
+ phy-handle = <ðphy1>;
+};
+
+&i2c0 {
+ multi-master;
+ bus-frequency = <1000000>;
+};
+
+&i2c1 {
+ /*
+ * PCA9548 (1-0070) provides 8 channels connecting to SMB (Switch
+ * Main Board).
+ */
+ i2c-switch@70 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x70>;
+ i2c-mux-idle-disconnect;
+
+ imux16: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux17: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ imux18: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux19: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+
+ imux20: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ };
+
+ imux21: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ imux22: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ };
+
+ imux23: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+ };
+};
+
+&i2c2 {
+ /*
+ * PCA9548 (2-0070) provides 8 channels connecting to SCM (System
+ * Controller Module).
+ */
+ i2c-switch@70 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x70>;
+ i2c-mux-idle-disconnect;
+
+ imux24: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux25: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ imux26: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux27: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+
+ imux28: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ };
+
+ imux29: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ imux30: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ };
+
+ imux31: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+ };
+};
+
+&i2c3 {
+ /*
+ * PCA9548 (3-0070) provides 8 channels connecting to SMB (Switch
+ * Main Board).
+ */
+ i2c-switch@70 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x70>;
+ i2c-mux-idle-disconnect;
+
+ imux32: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux33: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ imux34: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux35: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+
+ imux36: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ };
+
+ imux37: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ imux38: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ };
+
+ imux39: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+ };
+};
+
+&i2c6 {
+ lp5012@14 {
+ compatible = "ti,lp5012";
+ reg = <0x14>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ multi-led@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ color = <LED_COLOR_ID_MULTI>;
+ function = LED_FUNCTION_ACTIVITY;
+ label = "sys";
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_RED>;
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_BLUE>;
+ };
+
+ led@2 {
+ reg = <2>;
+ color = <LED_COLOR_ID_GREEN>;
+ };
+ };
+
+ multi-led@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ color = <LED_COLOR_ID_MULTI>;
+ function = LED_FUNCTION_ACTIVITY;
+ label = "fan";
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_RED>;
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_BLUE>;
+ };
+
+ led@2 {
+ reg = <2>;
+ color = <LED_COLOR_ID_GREEN>;
+ };
+ };
+
+ multi-led@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ color = <LED_COLOR_ID_MULTI>;
+ function = LED_FUNCTION_ACTIVITY;
+ label = "psu";
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_RED>;
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_BLUE>;
+ };
+
+ led@2 {
+ reg = <2>;
+ color = <LED_COLOR_ID_GREEN>;
+ };
+ };
+
+ multi-led@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ color = <LED_COLOR_ID_MULTI>;
+ function = LED_FUNCTION_ACTIVITY;
+ label = "scm";
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_RED>;
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_BLUE>;
+ };
+
+ led@2 {
+ reg = <2>;
+ color = <LED_COLOR_ID_GREEN>;
+ };
+ };
+ };
+};
+
+&i2c8 {
+ /*
+ * PCA9548 (8-0070) provides 8 channels connecting to PDB (Power
+ * Delivery Board).
+ */
+ i2c-switch@70 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x70>;
+ i2c-mux-idle-disconnect;
+
+ imux40: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux41: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ imux42: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux43: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+
+ imux44: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ };
+
+ imux45: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ imux46: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ };
+
+ imux47: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+
+ };
+};
+
+&i2c15 {
+ /*
+ * PCA9548 (15-0076) provides 8 channels connecting to FCM (Fan
+ * Controller Module).
+ */
+ i2c-switch@76 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x76>;
+ i2c-mux-idle-disconnect;
+
+ imux48: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux49: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ imux50: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux51: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+
+ imux52: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ };
+
+ imux53: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ imux54: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ };
+
+ imux55: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+ };
+};
--
2.17.1
From: Tao Ren <[email protected]>
Add initial version of device tree for Facebook Fuji (AST2600) BMC.
Signed-off-by: Tao Ren <[email protected]>
---
arch/arm/boot/dts/Makefile | 1 +
.../arm/boot/dts/aspeed-bmc-facebook-fuji.dts | 1276 +++++++++++++++++
2 files changed, 1277 insertions(+)
create mode 100644 arch/arm/boot/dts/aspeed-bmc-facebook-fuji.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 7cbb982a7c8b..9765e2ff5bfe 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1412,6 +1412,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
aspeed-bmc-facebook-cloudripper.dtb \
aspeed-bmc-facebook-cmm.dtb \
aspeed-bmc-facebook-elbert.dtb \
+ aspeed-bmc-facebook-fuji.dtb \
aspeed-bmc-facebook-galaxy100.dtb \
aspeed-bmc-facebook-minipack.dtb \
aspeed-bmc-facebook-tiogapass.dtb \
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-fuji.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-fuji.dts
new file mode 100644
index 000000000000..382cbbcf908d
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-facebook-fuji.dts
@@ -0,0 +1,1276 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2020 Facebook Inc.
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include "ast2600-facebook-netbmc-common.dtsi"
+
+/ {
+ model = "Facebook Fuji BMC";
+ compatible = "facebook,fuji-bmc", "aspeed,ast2600";
+
+ aliases {
+ /*
+ * PCA9548 (2-0070) provides 8 channels connecting to
+ * SCM (System Controller Module).
+ */
+ i2c16 = &imux16;
+ i2c17 = &imux17;
+ i2c18 = &imux18;
+ i2c19 = &imux19;
+ i2c20 = &imux20;
+ i2c21 = &imux21;
+ i2c22 = &imux22;
+ i2c23 = &imux23;
+
+ /*
+ * PCA9548 (8-0070) provides 8 channels connecting to
+ * SMB (Switch Main Board).
+ */
+ i2c24 = &imux24;
+ i2c25 = &imux25;
+ i2c26 = &imux26;
+ i2c27 = &imux27;
+ i2c28 = &imux28;
+ i2c29 = &imux29;
+ i2c30 = &imux30;
+ i2c31 = &imux31;
+
+ /*
+ * PCA9548 (11-0077) provides 8 channels connecting to
+ * SMB (Switch Main Board).
+ */
+ i2c40 = &imux40;
+ i2c41 = &imux41;
+ i2c42 = &imux42;
+ i2c43 = &imux43;
+ i2c44 = &imux44;
+ i2c45 = &imux45;
+ i2c46 = &imux46;
+ i2c47 = &imux47;
+
+ /*
+ * PCA9548 (24-0071) provides 8 channels connecting to
+ * PDB-Left.
+ */
+ i2c48 = &imux48;
+ i2c49 = &imux49;
+ i2c50 = &imux50;
+ i2c51 = &imux51;
+ i2c52 = &imux52;
+ i2c53 = &imux53;
+ i2c54 = &imux54;
+ i2c55 = &imux55;
+
+ /*
+ * PCA9548 (25-0072) provides 8 channels connecting to
+ * PDB-Right.
+ */
+ i2c56 = &imux56;
+ i2c57 = &imux57;
+ i2c58 = &imux58;
+ i2c59 = &imux59;
+ i2c60 = &imux60;
+ i2c61 = &imux61;
+ i2c62 = &imux62;
+ i2c63 = &imux63;
+
+ /*
+ * PCA9548 (26-0076) provides 8 channels connecting to
+ * FCM1.
+ */
+ i2c64 = &imux64;
+ i2c65 = &imux65;
+ i2c66 = &imux66;
+ i2c67 = &imux67;
+ i2c68 = &imux68;
+ i2c69 = &imux69;
+ i2c70 = &imux70;
+ i2c71 = &imux71;
+
+ /*
+ * PCA9548 (27-0076) provides 8 channels connecting to
+ * FCM2.
+ */
+ i2c72 = &imux72;
+ i2c73 = &imux73;
+ i2c74 = &imux74;
+ i2c75 = &imux75;
+ i2c76 = &imux76;
+ i2c77 = &imux77;
+ i2c78 = &imux78;
+ i2c79 = &imux79;
+
+ /*
+ * PCA9548 (40-0076) provides 8 channels connecting to
+ * PIM1.
+ */
+ i2c80 = &imux80;
+ i2c81 = &imux81;
+ i2c82 = &imux82;
+ i2c83 = &imux83;
+ i2c84 = &imux84;
+ i2c85 = &imux85;
+ i2c86 = &imux86;
+ i2c87 = &imux87;
+
+ /*
+ * PCA9548 (41-0076) provides 8 channels connecting to
+ * PIM2.
+ */
+ i2c88 = &imux88;
+ i2c89 = &imux89;
+ i2c90 = &imux90;
+ i2c91 = &imux91;
+ i2c92 = &imux92;
+ i2c93 = &imux93;
+ i2c94 = &imux94;
+ i2c95 = &imux95;
+
+ /*
+ * PCA9548 (42-0076) provides 8 channels connecting to
+ * PIM3.
+ */
+ i2c96 = &imux96;
+ i2c97 = &imux97;
+ i2c98 = &imux98;
+ i2c99 = &imux99;
+ i2c100 = &imux100;
+ i2c101 = &imux101;
+ i2c102 = &imux102;
+ i2c103 = &imux103;
+
+ /*
+ * PCA9548 (43-0076) provides 8 channels connecting to
+ * PIM4.
+ */
+ i2c104 = &imux104;
+ i2c105 = &imux105;
+ i2c106 = &imux106;
+ i2c107 = &imux107;
+ i2c108 = &imux108;
+ i2c109 = &imux109;
+ i2c110 = &imux110;
+ i2c111 = &imux111;
+
+ /*
+ * PCA9548 (44-0076) provides 8 channels connecting to
+ * PIM5.
+ */
+ i2c112 = &imux112;
+ i2c113 = &imux113;
+ i2c114 = &imux114;
+ i2c115 = &imux115;
+ i2c116 = &imux116;
+ i2c117 = &imux117;
+ i2c118 = &imux118;
+ i2c119 = &imux119;
+
+ /*
+ * PCA9548 (45-0076) provides 8 channels connecting to
+ * PIM6.
+ */
+ i2c120 = &imux120;
+ i2c121 = &imux121;
+ i2c122 = &imux122;
+ i2c123 = &imux123;
+ i2c124 = &imux124;
+ i2c125 = &imux125;
+ i2c126 = &imux126;
+ i2c127 = &imux127;
+
+ /*
+ * PCA9548 (46-0076) provides 8 channels connecting to
+ * PIM7.
+ */
+ i2c128 = &imux128;
+ i2c129 = &imux129;
+ i2c130 = &imux130;
+ i2c131 = &imux131;
+ i2c132 = &imux132;
+ i2c133 = &imux133;
+ i2c134 = &imux134;
+ i2c135 = &imux135;
+
+ /*
+ * PCA9548 (47-0076) provides 8 channels connecting to
+ * PIM8.
+ */
+ i2c136 = &imux136;
+ i2c137 = &imux137;
+ i2c138 = &imux138;
+ i2c139 = &imux139;
+ i2c140 = &imux140;
+ i2c141 = &imux141;
+ i2c142 = &imux142;
+ i2c143 = &imux143;
+ };
+
+ spi_gpio: spi-gpio {
+ num-chipselects = <3>;
+ cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>,
+ <0>, /* device reg=<1> does not exist */
+ <&gpio0 ASPEED_GPIO(X, 2) GPIO_ACTIVE_HIGH>;
+
+ eeprom@2 {
+ compatible = "atmel,at93c46d";
+ spi-max-frequency = <250000>;
+ data-size = <16>;
+ spi-cs-high;
+ reg = <2>;
+ };
+ };
+};
+
+&spi1 {
+ status = "okay";
+
+ /*
+ * Customize spi1 flash memory size to 32MB (maximum flash size on
+ * the bus) to save vmalloc space.
+ */
+ reg = < 0x1e630000 0xc4
+ 0x30000000 0x2000000 >;
+
+ flash@0 {
+ status = "okay";
+ m25p,fast-read;
+ label = "spi1.0";
+ spi-max-frequency = <5000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ flash1@0 {
+ reg = <0x0 0x2000000>;
+ label = "system-flash";
+ };
+ };
+ };
+};
+
+&i2c0 {
+ multi-master;
+ bus-frequency = <1000000>;
+};
+
+&i2c2 {
+ /*
+ * PCA9548 (2-0070) provides 8 channels connecting to SCM (System
+ * Controller Module).
+ */
+ i2c-switch@70 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x70>;
+ i2c-mux-idle-disconnect;
+
+ imux16: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ adm1278@10 {
+ compatible = "adi,adm1278";
+ reg = <0x10>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ shunt-resistor-micro-ohms = <1500>;
+ };
+ };
+
+ imux17: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ imux18: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux19: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+
+ imux20: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ };
+
+ imux21: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ imux22: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ };
+
+ imux23: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+ };
+};
+
+&i2c8 {
+ /*
+ * PCA9548 (8-0070) provides 8 channels connecting to SMB (Switch
+ * Main Board).
+ */
+ i2c-switch@70 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x70>;
+ i2c-mux-idle-disconnect;
+
+ imux24: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ i2c-switch@71 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x71>;
+ i2c-mux-idle-disconnect;
+
+ imux48: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux49: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ imux50: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+
+ lp5012@14 {
+ compatible = "ti,lp5012";
+ reg = <0x14>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ multi-led@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ color = <LED_COLOR_ID_MULTI>;
+ function = LED_FUNCTION_ACTIVITY;
+ label = "sys";
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_RED>;
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_BLUE>;
+ };
+
+ led@2 {
+ reg = <2>;
+ color = <LED_COLOR_ID_GREEN>;
+ };
+ };
+
+ multi-led@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ color = <LED_COLOR_ID_MULTI>;
+ function = LED_FUNCTION_ACTIVITY;
+ label = "fan";
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_RED>;
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_BLUE>;
+ };
+
+ led@2 {
+ reg = <2>;
+ color = <LED_COLOR_ID_GREEN>;
+ };
+ };
+
+ multi-led@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ color = <LED_COLOR_ID_MULTI>;
+ function = LED_FUNCTION_ACTIVITY;
+ label = "psu";
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_RED>;
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_BLUE>;
+ };
+
+ led@2 {
+ reg = <2>;
+ color = <LED_COLOR_ID_GREEN>;
+ };
+ };
+
+ multi-led@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ color = <LED_COLOR_ID_MULTI>;
+ function = LED_FUNCTION_ACTIVITY;
+ label = "smb";
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_RED>;
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_BLUE>;
+ };
+
+ led@2 {
+ reg = <2>;
+ color = <LED_COLOR_ID_GREEN>;
+ };
+ };
+ };
+ };
+
+ imux51: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+
+ imux52: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ };
+
+ imux53: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ imux54: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ };
+
+ imux55: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+ };
+
+ };
+
+ imux25: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ i2c-switch@72 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x72>;
+ i2c-mux-idle-disconnect;
+
+ imux56: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux57: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ imux58: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux59: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+
+ imux60: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ };
+
+ imux61: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ imux62: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ };
+
+ imux63: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+ };
+
+ };
+
+ imux26: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+
+ i2c-switch@76 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x76>;
+ i2c-mux-idle-disconnect;
+
+ imux64: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux65: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ imux66: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux67: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+
+ adm1278@10 {
+ compatible = "adi,adm1278";
+ reg = <0x10>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ shunt-resistor-micro-ohms = <250>;
+ };
+ };
+
+ imux68: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ };
+
+ imux69: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ imux70: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ };
+
+ imux71: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+ };
+
+ };
+
+ imux27: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+
+ i2c-switch@76 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x76>;
+ i2c-mux-idle-disconnect;
+
+ imux72: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux73: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ imux74: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux75: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+
+ adm1278@10 {
+ compatible = "adi,adm1278";
+ reg = <0x10>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ shunt-resistor-micro-ohms = <250>;
+ };
+ };
+
+ imux76: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ };
+
+ imux77: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ imux78: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ };
+
+ imux79: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+ };
+
+ };
+
+ imux28: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ };
+
+ imux29: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ imux30: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ };
+
+ imux31: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+
+ };
+};
+
+&i2c11 {
+ status = "okay";
+
+ /*
+ * PCA9548 (11-0077) provides 8 channels connecting to SMB (Switch
+ * Main Board).
+ */
+ i2c-switch@77 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x77>;
+ i2c-mux-idle-disconnect;
+
+ imux40: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ i2c-switch@76 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x76>;
+ i2c-mux-idle-disconnect;
+
+ imux80: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux81: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ imux82: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux83: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+
+ imux84: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ };
+
+ imux85: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ imux86: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ };
+
+ imux87: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+ };
+
+ };
+
+ imux41: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ i2c-switch@76 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x76>;
+ i2c-mux-idle-disconnect;
+
+ imux88: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux89: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ imux90: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux91: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+
+ imux92: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ };
+
+ imux93: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ imux94: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ };
+
+ imux95: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+ };
+
+ };
+
+ imux42: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+
+ i2c-switch@76 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x76>;
+ i2c-mux-idle-disconnect;
+
+ imux96: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux97: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ imux98: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux99: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+
+ imux100: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ };
+
+ imux101: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ imux102: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ };
+
+ imux103: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+ };
+
+ };
+
+ imux43: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+
+ i2c-switch@76 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x76>;
+ i2c-mux-idle-disconnect;
+
+ imux104: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux105: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ imux106: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux107: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+
+ imux108: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ };
+
+ imux109: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ imux110: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ };
+
+ imux111: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+ };
+
+ };
+
+ imux44: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+
+ i2c-switch@76 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x76>;
+ i2c-mux-idle-disconnect;
+
+ imux112: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux113: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ imux114: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux115: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+
+ imux116: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ };
+
+ imux117: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ imux118: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ };
+
+ imux119: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+ };
+
+ };
+
+ imux45: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+
+ i2c-switch@76 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x76>;
+ i2c-mux-idle-disconnect;
+
+ imux120: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux121: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ imux122: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux123: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+
+ imux124: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ };
+
+ imux125: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ imux126: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ };
+
+ imux127: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+ };
+
+ };
+
+ imux46: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+
+ i2c-switch@76 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x76>;
+ i2c-mux-idle-disconnect;
+
+ imux128: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux129: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ imux130: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux131: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+
+ imux132: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ };
+
+ imux133: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ imux134: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ };
+
+ imux135: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+ };
+
+ };
+
+ imux47: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+
+ i2c-switch@76 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x76>;
+ i2c-mux-idle-disconnect;
+
+ imux136: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux137: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ imux138: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux139: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+
+ imux140: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ };
+
+ imux141: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ imux142: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ };
+
+ imux143: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+ };
+
+ };
+
+ };
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&mdio1 {
+ status = "okay";
+
+ ethphy3: ethernet-phy@13 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0x0d>;
+ };
+};
+
+&mac3 {
+ phy-handle = <ðphy3>;
+};
--
2.17.1
From: Tao Ren <[email protected]>
Add initial version of device tree for Facebook Elbert (AST2600) BMC.
Signed-off-by: Tao Ren <[email protected]>
---
arch/arm/boot/dts/Makefile | 1 +
.../boot/dts/aspeed-bmc-facebook-elbert.dts | 185 ++++++++++++++++++
2 files changed, 186 insertions(+)
create mode 100644 arch/arm/boot/dts/aspeed-bmc-facebook-elbert.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 74c760038f28..7cbb982a7c8b 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1411,6 +1411,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
aspeed-bmc-bytedance-g220a.dtb \
aspeed-bmc-facebook-cloudripper.dtb \
aspeed-bmc-facebook-cmm.dtb \
+ aspeed-bmc-facebook-elbert.dtb \
aspeed-bmc-facebook-galaxy100.dtb \
aspeed-bmc-facebook-minipack.dtb \
aspeed-bmc-facebook-tiogapass.dtb \
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-elbert.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-elbert.dts
new file mode 100644
index 000000000000..27b43fe099f1
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-facebook-elbert.dts
@@ -0,0 +1,185 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2020 Facebook Inc.
+
+/dts-v1/;
+
+#include "ast2600-facebook-netbmc-common.dtsi"
+
+/ {
+ model = "Facebook Elbert BMC";
+ compatible = "facebook,elbert-bmc", "aspeed,ast2600";
+
+ aliases {
+ serial0 = &uart5;
+ serial1 = &uart1;
+ serial2 = &uart2;
+ serial3 = &uart3;
+
+ /*
+ * 8 child channels of PCA9548 2-0075.
+ */
+ i2c16 = &imux16;
+ i2c17 = &imux17;
+ i2c18 = &imux18;
+ i2c19 = &imux19;
+ i2c20 = &imux20;
+ i2c21 = &imux21;
+ i2c22 = &imux22;
+ i2c23 = &imux23;
+
+ /*
+ * 8 child channels of PCA9548 5-0075.
+ */
+ i2c24 = &imux24;
+ i2c25 = &imux25;
+ i2c26 = &imux26;
+ i2c27 = &imux27;
+ i2c28 = &imux28;
+ i2c29 = &imux29;
+ i2c30 = &imux30;
+ i2c31 = &imux31;
+ };
+
+ chosen {
+ stdout-path = &uart5;
+ };
+
+ spi_gpio: spi-gpio {
+ num-chipselects = <1>;
+ cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>;
+ };
+};
+
+&lpc_ctrl {
+ status = "okay";
+};
+
+&kcs2 {
+ status = "okay";
+ aspeed,lpc-io-reg = <0xca8>;
+};
+
+&kcs3 {
+ status = "okay";
+ aspeed,lpc-io-reg = <0xca2>;
+};
+
+&i2c2 {
+ i2c-switch@75 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x75>;
+ i2c-mux-idle-disconnect;
+
+ imux16: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux17: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ imux18: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux19: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+
+ imux20: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ };
+
+ imux21: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ imux22: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ };
+
+ imux23: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+ };
+};
+
+&i2c5 {
+ i2c-switch@75 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x75>;
+ i2c-mux-idle-disconnect;
+
+ imux24: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux25: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ imux26: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux27: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+
+ imux28: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ };
+
+ imux29: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ imux30: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ };
+
+ imux31: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+ };
+};
+
+&i2c11 {
+ status = "okay";
+};
--
2.17.1
On Thu, 5 Aug 2021 at 01:20, Tao Ren <[email protected]> wrote:
>
> On Thu, Aug 05, 2021 at 12:28:02AM +0000, Joel Stanley wrote:
> > On Wed, 28 Jul 2021 at 23:38, <[email protected]> wrote:
> > >
> > > From: Tao Ren <[email protected]>
> > >
> > > Add initial version of device tree for Facebook Fuji (AST2600) BMC.
> >
> > I like to read what kind of platform the BMC is going into if you can
> > add that detail, but it's not essential.
>
> Sure. I will add more details in v2.
>
> > > +&spi1 {
> > > + status = "okay";
> > > +
> > > + /*
> > > + * Customize spi1 flash memory size to 32MB (maximum flash size on
> > > + * the bus) to save vmalloc space.
> > > + */
> > > + reg = < 0x1e630000 0xc4
> > > + 0x30000000 0x2000000 >;
> >
> > Which driver supports this?
> >
> > It would be great to see Facebook work to get the SPI NOR driver for
> > the ast2600 merged to mainline.
> >
> > I doubt the IBM team will get to this, as we are using eMMC instead.
>
> Ah, I just checked aspeed-g6.dtsi (ast2600-spi) in mainline and I thought
> the driver patches were also upstreamed. Let me remove the entry for now,
> and will add it back when the driver is ready.
If it helps you, I don't mind it staying in your dts. I would like to
see some effort on the driver though.
>
> >
> > > +
> > > + flash@0 {
> > > + status = "okay";
> > > + m25p,fast-read;
> > > + label = "spi1.0";
> > > + spi-max-frequency = <5000000>;
> > > +
> > > + partitions {
> > > + compatible = "fixed-partitions";
> > > + #address-cells = <1>;
> > > + #size-cells = <1>;
> > > +
> > > + flash1@0 {
> > > + reg = <0x0 0x2000000>;
> > > + label = "system-flash";
> > > + };
> > > + };
> > > + };
> > > +};
> >
> > > +&ehci1 {
> > > + status = "okay";
> > > +};
> >
> > Have you verified that USB works with mainline? I've had reports of it
> > working on 5.8 but it seems to have regressed as of v5.10.
>
> It stopped working on ASPEED since commit 280a9045bb18 ("ehci: fix EHCI
> host controller initialization sequence"): ehci_handshake() returns
> error because HCHalted bit EHCI24[12] stays at 1.
>
> I have a dirty hack in my tree (ignoring the halt bit) and it "works" on
> AST2500 and AST2600. Let me send an email to openbmc and aspeed email
> groups to see if anyone has more context.
We discovered the same, except in my testing it wasn't actually
"working" on my EVB. I have a A3 EVB on my desk and when plugging in a
USB key nothing happened.
>
> Meanwhile, should I delete the entry until the fix is ready in driver?
Again, leave it in I think.
>
> > > +&mdio1 {
> > > + status = "okay";
> > > +
> > > + ethphy3: ethernet-phy@13 {
> > > + compatible = "ethernet-phy-ieee802.3-c22";
> > > + reg = <0x0d>;
> > > + };
> > > +};
> > > +
> > > +&mac3 {
> > > + phy-handle = <ðphy3>;
> >
> > status = okay?
> >
> > You should specify the pinmux too I think, even if the default happens
> > to work, so that other devices cannot claim the pins.
>
> status is set in ast2600 common dtsi, but let me set it here to avoid
> confusion. Will update pinmux in v2. Thanks.
Are you looking at mainline? I think it's disabled by default there:
https://elixir.bootlin.com/linux/latest/source/arch/arm/boot/dts/aspeed-g6.dtsi#L246
>
> >
> > Cheers,
> >
> > Joel
>
> Cheers,
>
> Tao
On Thu, 5 Aug 2021 at 02:09, Tao Ren <[email protected]> wrote:
>
> On Thu, Aug 05, 2021 at 01:37:29AM +0000, Joel Stanley wrote:
> > On Thu, 5 Aug 2021 at 01:20, Tao Ren <[email protected]> wrote:
> > > > > +&ehci1 {
> > > > > + status = "okay";
> > > > > +};
> > > >
> > > > Have you verified that USB works with mainline? I've had reports of it
> > > > working on 5.8 but it seems to have regressed as of v5.10.
> > >
> > > It stopped working on ASPEED since commit 280a9045bb18 ("ehci: fix EHCI
> > > host controller initialization sequence"): ehci_handshake() returns
> > > error because HCHalted bit EHCI24[12] stays at 1.
> > >
> > > I have a dirty hack in my tree (ignoring the halt bit) and it "works" on
> > > AST2500 and AST2600. Let me send an email to openbmc and aspeed email
> > > groups to see if anyone has more context.
> >
> > We discovered the same, except in my testing it wasn't actually
> > "working" on my EVB. I have a A3 EVB on my desk and when plugging in a
> > USB key nothing happened.
>
> We have a non-removable USB device on Fuji (AST2600) BMC and it can be
> enumerated successfully (after applying the hack). Let me vist the lab
> and plug a USB key to CMM (AST2500) BMC sometime next week. Will collect
> results and send out email then.
Thanks!
> > > status is set in ast2600 common dtsi, but let me set it here to avoid
> > > confusion. Will update pinmux in v2. Thanks.
> >
> > Are you looking at mainline? I think it's disabled by default there:
> >
> > https://elixir.bootlin.com/linux/latest/source/arch/arm/boot/dts/aspeed-g6.dtsi#L246
>
> Sorry for the confusion, Joel. I mean the device is enabled in
> "ast2600-facebook-netbmc-common.dtsi" (patch #3 in the series). Do we
> still need to set status to "okay" explicitly in platform dts (to avoid
> confusion)?
I see, thanks for explaining. It's a downside of the device tree
bindings for the ethernet device.
Given you will be the one working with the board, I think it's up to
you how you lay it out. You could choose to add a comment to the
platform dts, or put the hunk you currently have in the common.dtsi in
the platform.
>
> &mac3 {
> status = "okay";
> phy-mode = "rgmii";
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_rgmii4_default>;
> };
On Wed, 28 Jul 2021 at 23:38, <[email protected]> wrote:
>
> From: Tao Ren <[email protected]>
>
> Add initial version of device tree for Facebook Fuji (AST2600) BMC.
I like to read what kind of platform the BMC is going into if you can
add that detail, but it's not essential.
> +&spi1 {
> + status = "okay";
> +
> + /*
> + * Customize spi1 flash memory size to 32MB (maximum flash size on
> + * the bus) to save vmalloc space.
> + */
> + reg = < 0x1e630000 0xc4
> + 0x30000000 0x2000000 >;
Which driver supports this?
It would be great to see Facebook work to get the SPI NOR driver for
the ast2600 merged to mainline.
I doubt the IBM team will get to this, as we are using eMMC instead.
> +
> + flash@0 {
> + status = "okay";
> + m25p,fast-read;
> + label = "spi1.0";
> + spi-max-frequency = <5000000>;
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + flash1@0 {
> + reg = <0x0 0x2000000>;
> + label = "system-flash";
> + };
> + };
> + };
> +};
> +&ehci1 {
> + status = "okay";
> +};
Have you verified that USB works with mainline? I've had reports of it
working on 5.8 but it seems to have regressed as of v5.10.
> +&mdio1 {
> + status = "okay";
> +
> + ethphy3: ethernet-phy@13 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0x0d>;
> + };
> +};
> +
> +&mac3 {
> + phy-handle = <ðphy3>;
status = okay?
You should specify the pinmux too I think, even if the default happens
to work, so that other devices cannot claim the pins.
Cheers,
Joel
On Thu, Aug 05, 2021 at 01:37:29AM +0000, Joel Stanley wrote:
> On Thu, 5 Aug 2021 at 01:20, Tao Ren <[email protected]> wrote:
> >
> > On Thu, Aug 05, 2021 at 12:28:02AM +0000, Joel Stanley wrote:
> > > On Wed, 28 Jul 2021 at 23:38, <[email protected]> wrote:
> > > >
> > > > From: Tao Ren <[email protected]>
> > > >
> > > > Add initial version of device tree for Facebook Fuji (AST2600) BMC.
> > >
> > > I like to read what kind of platform the BMC is going into if you can
> > > add that detail, but it's not essential.
> >
> > Sure. I will add more details in v2.
> >
> > > > +&spi1 {
> > > > + status = "okay";
> > > > +
> > > > + /*
> > > > + * Customize spi1 flash memory size to 32MB (maximum flash size on
> > > > + * the bus) to save vmalloc space.
> > > > + */
> > > > + reg = < 0x1e630000 0xc4
> > > > + 0x30000000 0x2000000 >;
> > >
> > > Which driver supports this?
> > >
> > > It would be great to see Facebook work to get the SPI NOR driver for
> > > the ast2600 merged to mainline.
> > >
> > > I doubt the IBM team will get to this, as we are using eMMC instead.
> >
> > Ah, I just checked aspeed-g6.dtsi (ast2600-spi) in mainline and I thought
> > the driver patches were also upstreamed. Let me remove the entry for now,
> > and will add it back when the driver is ready.
>
> If it helps you, I don't mind it staying in your dts. I would like to
> see some effort on the driver though.
>
> >
> > >
> > > > +
> > > > + flash@0 {
> > > > + status = "okay";
> > > > + m25p,fast-read;
> > > > + label = "spi1.0";
> > > > + spi-max-frequency = <5000000>;
> > > > +
> > > > + partitions {
> > > > + compatible = "fixed-partitions";
> > > > + #address-cells = <1>;
> > > > + #size-cells = <1>;
> > > > +
> > > > + flash1@0 {
> > > > + reg = <0x0 0x2000000>;
> > > > + label = "system-flash";
> > > > + };
> > > > + };
> > > > + };
> > > > +};
> > >
> > > > +&ehci1 {
> > > > + status = "okay";
> > > > +};
> > >
> > > Have you verified that USB works with mainline? I've had reports of it
> > > working on 5.8 but it seems to have regressed as of v5.10.
> >
> > It stopped working on ASPEED since commit 280a9045bb18 ("ehci: fix EHCI
> > host controller initialization sequence"): ehci_handshake() returns
> > error because HCHalted bit EHCI24[12] stays at 1.
> >
> > I have a dirty hack in my tree (ignoring the halt bit) and it "works" on
> > AST2500 and AST2600. Let me send an email to openbmc and aspeed email
> > groups to see if anyone has more context.
>
> We discovered the same, except in my testing it wasn't actually
> "working" on my EVB. I have a A3 EVB on my desk and when plugging in a
> USB key nothing happened.
We have a non-removable USB device on Fuji (AST2600) BMC and it can be
enumerated successfully (after applying the hack). Let me vist the lab
and plug a USB key to CMM (AST2500) BMC sometime next week. Will collect
results and send out email then.
>
> >
> > Meanwhile, should I delete the entry until the fix is ready in driver?
>
> Again, leave it in I think.
>
> >
> > > > +&mdio1 {
> > > > + status = "okay";
> > > > +
> > > > + ethphy3: ethernet-phy@13 {
> > > > + compatible = "ethernet-phy-ieee802.3-c22";
> > > > + reg = <0x0d>;
> > > > + };
> > > > +};
> > > > +
> > > > +&mac3 {
> > > > + phy-handle = <ðphy3>;
> > >
> > > status = okay?
> > >
> > > You should specify the pinmux too I think, even if the default happens
> > > to work, so that other devices cannot claim the pins.
> >
> > status is set in ast2600 common dtsi, but let me set it here to avoid
> > confusion. Will update pinmux in v2. Thanks.
>
> Are you looking at mainline? I think it's disabled by default there:
>
> https://elixir.bootlin.com/linux/latest/source/arch/arm/boot/dts/aspeed-g6.dtsi#L246
Sorry for the confusion, Joel. I mean the device is enabled in
"ast2600-facebook-netbmc-common.dtsi" (patch #3 in the series). Do we
still need to set status to "okay" explicitly in platform dts (to avoid
confusion)?
&mac3 {
status = "okay";
phy-mode = "rgmii";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_rgmii4_default>;
};
>
> >
> > >
> > > Cheers,
> > >
> > > Joel
> >
> > Cheers,
> >
> > Tao
On Thu, Aug 05, 2021 at 12:28:02AM +0000, Joel Stanley wrote:
> On Wed, 28 Jul 2021 at 23:38, <[email protected]> wrote:
> >
> > From: Tao Ren <[email protected]>
> >
> > Add initial version of device tree for Facebook Fuji (AST2600) BMC.
>
> I like to read what kind of platform the BMC is going into if you can
> add that detail, but it's not essential.
Sure. I will add more details in v2.
> > +&spi1 {
> > + status = "okay";
> > +
> > + /*
> > + * Customize spi1 flash memory size to 32MB (maximum flash size on
> > + * the bus) to save vmalloc space.
> > + */
> > + reg = < 0x1e630000 0xc4
> > + 0x30000000 0x2000000 >;
>
> Which driver supports this?
>
> It would be great to see Facebook work to get the SPI NOR driver for
> the ast2600 merged to mainline.
>
> I doubt the IBM team will get to this, as we are using eMMC instead.
Ah, I just checked aspeed-g6.dtsi (ast2600-spi) in mainline and I thought
the driver patches were also upstreamed. Let me remove the entry for now,
and will add it back when the driver is ready.
>
> > +
> > + flash@0 {
> > + status = "okay";
> > + m25p,fast-read;
> > + label = "spi1.0";
> > + spi-max-frequency = <5000000>;
> > +
> > + partitions {
> > + compatible = "fixed-partitions";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + flash1@0 {
> > + reg = <0x0 0x2000000>;
> > + label = "system-flash";
> > + };
> > + };
> > + };
> > +};
>
> > +&ehci1 {
> > + status = "okay";
> > +};
>
> Have you verified that USB works with mainline? I've had reports of it
> working on 5.8 but it seems to have regressed as of v5.10.
It stopped working on ASPEED since commit 280a9045bb18 ("ehci: fix EHCI
host controller initialization sequence"): ehci_handshake() returns
error because HCHalted bit EHCI24[12] stays at 1.
I have a dirty hack in my tree (ignoring the halt bit) and it "works" on
AST2500 and AST2600. Let me send an email to openbmc and aspeed email
groups to see if anyone has more context.
Meanwhile, should I delete the entry until the fix is ready in driver?
> > +&mdio1 {
> > + status = "okay";
> > +
> > + ethphy3: ethernet-phy@13 {
> > + compatible = "ethernet-phy-ieee802.3-c22";
> > + reg = <0x0d>;
> > + };
> > +};
> > +
> > +&mac3 {
> > + phy-handle = <ðphy3>;
>
> status = okay?
>
> You should specify the pinmux too I think, even if the default happens
> to work, so that other devices cannot claim the pins.
status is set in ast2600 common dtsi, but let me set it here to avoid
confusion. Will update pinmux in v2. Thanks.
>
> Cheers,
>
> Joel
Cheers,
Tao