Currently xhci-mtk needs software-managed bandwidth allocation for
periodic endpoints, it allocates the microframe index for the first
start-split packet for each endpoint. As this index allocation logic
should avoid the conflicts with other full/low-speed periodic endpoints,
it uses the worst case byte budgets on high-speed bus bandwidth
For example, for an isochronos IN endpoint with 192 bytes budget,
it will consume the whole 4 u-frames(188 * 4) while the actual
full-speed bus budget should be just 192bytes.
This patch changes the low/full-speed bandwidth allocation logic
to use "approximate" best case budget for lower speed bandwidth
management. For the same endpoint from the above example, the
approximate best case budget is now reduced to (188 * 2) bytes.
Without this patch, many usb audio headsets with 3 interfaces
(audio input, audio output, and HID) cannot be configured
on xhci-mtk.
Signed-off-by: Ikjoon Jang <[email protected]>
---
drivers/usb/host/xhci-mtk-sch.c | 20 +++++++++++++-------
1 file changed, 13 insertions(+), 7 deletions(-)
diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index f9b4d27ce449..46cbf5d54f4f 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -459,16 +459,17 @@ static int check_fs_bus_bw(struct mu3h_sch_ep_info *sch_ep, int offset)
u32 num_esit, tmp;
int base;
int i, j;
+ u8 uframes = DIV_ROUND_UP(sch_ep->maxpkt, FS_PAYLOAD_MAX);
num_esit = XHCI_MTK_MAX_ESIT / sch_ep->esit;
+
+ if (sch_ep->ep_type == INT_IN_EP || sch_ep->ep_type == ISOC_IN_EP)
+ offset++;
+
for (i = 0; i < num_esit; i++) {
base = offset + i * sch_ep->esit;
- /*
- * Compared with hs bus, no matter what ep type,
- * the hub will always delay one uframe to send data
- */
- for (j = 0; j < sch_ep->cs_count; j++) {
+ for (j = 0; j < uframes; j++) {
tmp = tt->fs_bus_bw[base + j] + sch_ep->bw_cost_per_microframe;
if (tmp > FS_PAYLOAD_MAX)
return -ESCH_BW_OVERFLOW;
@@ -546,6 +547,8 @@ static void update_sch_tt(struct mu3h_sch_ep_info *sch_ep, bool used)
u32 base, num_esit;
int bw_updated;
int i, j;
+ int offset = sch_ep->offset;
+ u8 uframes = DIV_ROUND_UP(sch_ep->maxpkt, FS_PAYLOAD_MAX);
num_esit = XHCI_MTK_MAX_ESIT / sch_ep->esit;
@@ -554,10 +557,13 @@ static void update_sch_tt(struct mu3h_sch_ep_info *sch_ep, bool used)
else
bw_updated = -sch_ep->bw_cost_per_microframe;
+ if (sch_ep->ep_type == INT_IN_EP || sch_ep->ep_type == ISOC_IN_EP)
+ offset++;
+
for (i = 0; i < num_esit; i++) {
- base = sch_ep->offset + i * sch_ep->esit;
+ base = offset + i * sch_ep->esit;
- for (j = 0; j < sch_ep->cs_count; j++)
+ for (j = 0; j < uframes; j++)
tt->fs_bus_bw[base + j] += bw_updated;
}
--
2.32.0.554.ge1b32706d8-goog
On Thu, 2021-08-05 at 13:39 +0800, Ikjoon Jang wrote:
> Currently xhci-mtk needs software-managed bandwidth allocation for
> periodic endpoints, it allocates the microframe index for the first
> start-split packet for each endpoint. As this index allocation logic
> should avoid the conflicts with other full/low-speed periodic
> endpoints,
> it uses the worst case byte budgets on high-speed bus bandwidth
> For example, for an isochronos IN endpoint with 192 bytes budget,
> it will consume the whole 4 u-frames(188 * 4) while the actual
> full-speed bus budget should be just 192bytes.
>
> This patch changes the low/full-speed bandwidth allocation logic
> to use "approximate" best case budget for lower speed bandwidth
> management. For the same endpoint from the above example, the
> approximate best case budget is now reduced to (188 * 2) bytes.
>
> Without this patch, many usb audio headsets with 3 interfaces
> (audio input, audio output, and HID) cannot be configured
> on xhci-mtk.
>
> Signed-off-by: Ikjoon Jang <[email protected]>
> ---
>
> drivers/usb/host/xhci-mtk-sch.c | 20 +++++++++++++-------
> 1 file changed, 13 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-
> mtk-sch.c
> index f9b4d27ce449..46cbf5d54f4f 100644
> --- a/drivers/usb/host/xhci-mtk-sch.c
> +++ b/drivers/usb/host/xhci-mtk-sch.c
> @@ -459,16 +459,17 @@ static int check_fs_bus_bw(struct
> mu3h_sch_ep_info *sch_ep, int offset)
> u32 num_esit, tmp;
> int base;
> int i, j;
> + u8 uframes = DIV_ROUND_UP(sch_ep->maxpkt, FS_PAYLOAD_MAX);
>
> num_esit = XHCI_MTK_MAX_ESIT / sch_ep->esit;
> +
> + if (sch_ep->ep_type == INT_IN_EP || sch_ep->ep_type ==
> ISOC_IN_EP)
> + offset++;
> +
> for (i = 0; i < num_esit; i++) {
> base = offset + i * sch_ep->esit;
>
> - /*
> - * Compared with hs bus, no matter what ep type,
> - * the hub will always delay one uframe to send data
> - */
> - for (j = 0; j < sch_ep->cs_count; j++) {
> + for (j = 0; j < uframes; j++) {
Please don't calculate new value, should use the value calculated by
check_sch_tt().
See usb2.0 spec Figure 11-64, sometime will use 2 extra CS.
> tmp = tt->fs_bus_bw[base + j] + sch_ep-
> >bw_cost_per_microframe;
> if (tmp > FS_PAYLOAD_MAX)
> return -ESCH_BW_OVERFLOW;
> @@ -546,6 +547,8 @@ static void update_sch_tt(struct mu3h_sch_ep_info
> *sch_ep, bool used)
> u32 base, num_esit;
> int bw_updated;
> int i, j;
> + int offset = sch_ep->offset;
> + u8 uframes = DIV_ROUND_UP(sch_ep->maxpkt, FS_PAYLOAD_MAX);
>
> num_esit = XHCI_MTK_MAX_ESIT / sch_ep->esit;
>
> @@ -554,10 +557,13 @@ static void update_sch_tt(struct
> mu3h_sch_ep_info *sch_ep, bool used)
> else
> bw_updated = -sch_ep->bw_cost_per_microframe;
>
> + if (sch_ep->ep_type == INT_IN_EP || sch_ep->ep_type ==
> ISOC_IN_EP)
> + offset++;
> +
> for (i = 0; i < num_esit; i++) {
> - base = sch_ep->offset + i * sch_ep->esit;
> + base = offset + i * sch_ep->esit;
>
> - for (j = 0; j < sch_ep->cs_count; j++)
> + for (j = 0; j < uframes; j++)
> tt->fs_bus_bw[base + j] += bw_updated;
> }
>