Add support for Samsung Mobile Displays(SMD) Samsung S6D27A1 panel.
This display panel is used on Samsung mobile devices such as
Samsung Galaxy Ace 2 (GT-I8160) also known as Codina.
Markuss Broks (2):
drm/panel: Add DT bindings for Samsung S6D27A1 display panel
drm/panel: s6d27a1: Add driver for Samsung S6D27A1 display panel
.../display/panel/samsung,s6d27a1.yaml | 97 ++++++
drivers/gpu/drm/panel/Kconfig | 11 +
drivers/gpu/drm/panel/Makefile | 1 +
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c | 323 ++++++++++++++++++
4 files changed, 432 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6d27a1.yaml
create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6d27a1.c
--
2.32.0
This adds device-tree bindings for the Samsung S6D27A1 RGB
DPI display panel.
Signed-off-by: Markuss Broks <[email protected]>
v1 -> v2:
changed additionalProperties to unevaluatedProperties;
added vci-supply and vccio-supply as required;
---
.../display/panel/samsung,s6d27a1.yaml | 98 +++++++++++++++++++
1 file changed, 98 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6d27a1.yaml
diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6d27a1.yaml b/Documentation/devicetree/bindings/display/panel/samsung,s6d27a1.yaml
new file mode 100644
index 0000000000..26e3c820a2
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/samsung,s6d27a1.yaml
@@ -0,0 +1,98 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/samsung,s6d27a1.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung S6D27A1 display panel
+
+description: The S6D27A1 is a 480x800 DPI display panel from Samsung Mobile
+ Displays (SMD). The panel must obey the rules for a SPI slave device
+ as specified in spi/spi-controller.yaml
+
+maintainers:
+ - Markuss Broks <[email protected]>
+
+allOf:
+ - $ref: panel-common.yaml#
+
+properties:
+ compatible:
+ const: samsung,s6d27a1
+
+ reg: true
+
+ interrupts:
+ description: provides an optional ESD (electrostatic discharge)
+ interrupt that signals abnormalities in the display hardware.
+ This can also be raised for other reasons like erroneous
+ configuration.
+ maxItems: 1
+
+ reset-gpios: true
+
+ vci-supply:
+ description: regulator that supplies the VCI analog voltage
+ usually around 3.0 V
+
+ vccio-supply:
+ description: regulator that supplies the VCCIO voltage usually
+ around 1.8 V
+
+ backlight: true
+
+ spi-cpha: true
+
+ spi-cpol: true
+
+ spi-max-frequency:
+ maximum: 1200000
+
+ port: true
+
+required:
+ - compatible
+ - reg
+ - vci-supply
+ - vccio-supply
+ - spi-cpha
+ - spi-cpol
+ - port
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ spi {
+ compatible = "spi-gpio";
+ sck-gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
+ miso-gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
+ mosi-gpios = <&gpio 2 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&gpio 3 GPIO_ACTIVE_HIGH>;
+ num-chipselects = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ panel@0 {
+ compatible = "samsung,s6d27a1";
+ spi-max-frequency = <1200000>;
+ spi-cpha;
+ spi-cpol;
+ reg = <0>;
+ vci-supply = <&lcd_3v0_reg>;
+ vccio-supply = <&lcd_1v8_reg>;
+ reset-gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+ interrupt-parent = <&gpio>;
+ interrupts = <5 IRQ_TYPE_EDGE_RISING>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+ };
+
+...
--
2.32.0
This adds a driver for Samsung S6D27A1 display controller and panel.
This panel is found in the Samsung GT-I8160 mobile phone,
and possibly some other mobile phones.
This display needs manufacturer commands to configure it;
the commands used in this driver were taken from downstream driver
by Gareth Phillips; sadly, there is almost no documentation on what they
actually do.
This driver re-uses the DBI infrastructure to communicate with the display.
This driver is heavily based on WideChips WS2401 display controller
driver by Linus Walleij and on other panel drivers for reference.
Signed-off-by: Markuss Broks <[email protected]>
v2 -> v3:
fixed checkpatch warnings - not sure about MAINTAINERS, should I
put my name up there?
v3 -> v4:
- add a MAINTAINERS entry;
- drop s6d27a1_command macro; use mipi_dbi_command directly;
- dropped "panel initialized" dev_dbg message;
- add drm_panel_of_backlight call to handle backlight
on panel turn on/off;
- reorder drm_mipi_dbi and drm_modes headers:
I think they should be in alphabetic order?
---
MAINTAINERS | 6 +
drivers/gpu/drm/panel/Kconfig | 11 +
drivers/gpu/drm/panel/Makefile | 1 +
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c | 320 ++++++++++++++++++
4 files changed, 338 insertions(+)
create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6d27a1.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 851255b71c..c363209130 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -5962,6 +5962,12 @@ T: git git://anongit.freedesktop.org/drm/drm-misc
F: Documentation/devicetree/bindings/display/panel/samsung,lms397kf04.yaml
F: drivers/gpu/drm/panel/panel-samsung-db7430.c
+DRM DRIVER FOR SAMSUNG S6D27A1 PANELS
+M: Markuss Broks <[email protected]>
+S: Maintained
+F: Documentation/devicetree/bindings/display/panel/samsung,s6d27a1.yaml
+F: driver/gpu/drm/panel/panel-samsung-s6d27a1.c
+
DRM DRIVER FOR SITRONIX ST7703 PANELS
M: Guido Günther <[email protected]>
R: Purism Kernel Team <[email protected]>
diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
index beb581b96e..0b37849413 100644
--- a/drivers/gpu/drm/panel/Kconfig
+++ b/drivers/gpu/drm/panel/Kconfig
@@ -392,6 +392,17 @@ config DRM_PANEL_SAMSUNG_S6D16D0
depends on DRM_MIPI_DSI
select VIDEOMODE_HELPERS
+config DRM_PANEL_SAMSUNG_S6D27A1
+ tristate "Samsung S6D27A1 DPI panel driver"
+ depends on OF && SPI && GPIOLIB
+ select DRM_MIPI_DBI
+ help
+ Say Y here if you want to enable support for the Samsung
+ S6D27A1 DPI 480x800 panel.
+
+ This panel can be found in Samsung Galaxy Ace 2
+ GT-I8160 mobile phone.
+
config DRM_PANEL_SAMSUNG_S6E3HA2
tristate "Samsung S6E3HA2 DSI video mode panel"
depends on OF
diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
index c8132050bc..60c0149fc5 100644
--- a/drivers/gpu/drm/panel/Makefile
+++ b/drivers/gpu/drm/panel/Makefile
@@ -39,6 +39,7 @@ obj-$(CONFIG_DRM_PANEL_SAMSUNG_ATNA33XC20) += panel-samsung-atna33xc20.o
obj-$(CONFIG_DRM_PANEL_SAMSUNG_DB7430) += panel-samsung-db7430.o
obj-$(CONFIG_DRM_PANEL_SAMSUNG_LD9040) += panel-samsung-ld9040.o
obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6D16D0) += panel-samsung-s6d16d0.o
+obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6D27A1) += panel-samsung-s6d27a1.o
obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E3HA2) += panel-samsung-s6e3ha2.o
obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E63J0X03) += panel-samsung-s6e63j0x03.o
obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E63M0) += panel-samsung-s6e63m0.o
diff --git a/drivers/gpu/drm/panel/panel-samsung-s6d27a1.c b/drivers/gpu/drm/panel/panel-samsung-s6d27a1.c
new file mode 100644
index 0000000000..2dfcf48f2b
--- /dev/null
+++ b/drivers/gpu/drm/panel/panel-samsung-s6d27a1.c
@@ -0,0 +1,320 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Panel driver for the Samsung S6D27A1 480x800 DPI RGB panel.
+ * Found in the Samsung Galaxy Ace 2 GT-I8160 mobile phone.
+ */
+
+#include <drm/drm_mipi_dbi.h>
+#include <drm/drm_modes.h>
+#include <drm/drm_panel.h>
+
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/media-bus-format.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/regulator/consumer.h>
+#include <linux/spi/spi.h>
+
+#include <video/mipi_display.h>
+
+#define S6D27A1_PASSWD_L2 0xF0 /* Password Command for Level 2 Control */
+#define S6D27A1_RESCTL 0xB3 /* Resolution Select Control */
+#define S6D27A1_PANELCTL2 0xB4 /* ASG Signal Control */
+#define S6D27A1_READID1 0xDA /* Read panel ID 1 */
+#define S6D27A1_READID2 0xDB /* Read panel ID 2 */
+#define S6D27A1_READID3 0xDC /* Read panel ID 3 */
+#define S6D27A1_DISPCTL 0xF2 /* Display Control */
+#define S6D27A1_MANPWR 0xF3 /* Manual Control */
+#define S6D27A1_PWRCTL1 0xF4 /* Power Control */
+#define S6D27A1_SRCCTL 0xF6 /* Source Control */
+#define S6D27A1_PANELCTL 0xF7 /* Panel Control*/
+
+static const u8 s6d27a1_dbi_read_commands[] = {
+ S6D27A1_READID1,
+ S6D27A1_READID2,
+ S6D27A1_READID3,
+ 0, /* sentinel */
+};
+
+struct s6d27a1 {
+ struct device *dev;
+ struct mipi_dbi dbi;
+ struct drm_panel panel;
+ struct gpio_desc *reset;
+ struct regulator_bulk_data regulators[2];
+};
+
+static const struct drm_display_mode s6d27a1_480_800_mode = {
+ /*
+ * The vendor driver states that the S6D27A1 panel
+ * has a pixel clock frequency of 49920000 Hz / 2 = 24960000 Hz.
+ */
+ .clock = 24960,
+ .hdisplay = 480,
+ .hsync_start = 480 + 63,
+ .hsync_end = 480 + 63 + 2,
+ .htotal = 480 + 63 + 2 + 63,
+ .vdisplay = 800,
+ .vsync_start = 800 + 11,
+ .vsync_end = 800 + 11 + 2,
+ .vtotal = 800 + 11 + 2 + 10,
+ .width_mm = 50,
+ .height_mm = 84,
+ .flags = DRM_MODE_FLAG_NVSYNC | DRM_MODE_FLAG_NHSYNC,
+};
+
+static inline struct s6d27a1 *to_s6d27a1(struct drm_panel *panel)
+{
+ return container_of(panel, struct s6d27a1, panel);
+}
+
+static void s6d27a1_read_mtp_id(struct s6d27a1 *ctx)
+{
+ struct mipi_dbi *dbi = &ctx->dbi;
+ u8 id1, id2, id3;
+ int ret;
+
+ ret = mipi_dbi_command_read(dbi, S6D27A1_READID1, &id1);
+ if (ret) {
+ dev_err(ctx->dev, "unable to read MTP ID 1\n");
+ return;
+ }
+ ret = mipi_dbi_command_read(dbi, S6D27A1_READID2, &id2);
+ if (ret) {
+ dev_err(ctx->dev, "unable to read MTP ID 2\n");
+ return;
+ }
+ ret = mipi_dbi_command_read(dbi, S6D27A1_READID3, &id3);
+ if (ret) {
+ dev_err(ctx->dev, "unable to read MTP ID 3\n");
+ return;
+ }
+ dev_info(ctx->dev, "MTP ID: %02x %02x %02x\n", id1, id2, id3);
+}
+
+static int s6d27a1_power_on(struct s6d27a1 *ctx)
+{
+ struct mipi_dbi *dbi = &ctx->dbi;
+ int ret;
+
+ /* Power up */
+ ret = regulator_bulk_enable(ARRAY_SIZE(ctx->regulators),
+ ctx->regulators);
+ if (ret) {
+ dev_err(ctx->dev, "failed to enable regulators: %d\n", ret);
+ return ret;
+ }
+
+ msleep(20);
+
+ /* Assert reset >=1 ms */
+ gpiod_set_value_cansleep(ctx->reset, 1);
+ usleep_range(1000, 5000);
+ /* De-assert reset */
+ gpiod_set_value_cansleep(ctx->reset, 0);
+ /* Wait >= 10 ms */
+ msleep(20);
+
+ /*
+ * Exit sleep mode and initialize display - some hammering is
+ * necessary.
+ */
+ mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE);
+ mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE);
+ msleep(50);
+
+ /* Magic to unlock level 2 control of the display */
+ mipi_dbi_command(dbi, S6D27A1_PASSWD_L2, 0x5A, 0x5A);
+
+ /* Configure resolution to 480RGBx800 */
+ mipi_dbi_command(dbi, S6D27A1_RESCTL, 0x22);
+
+ mipi_dbi_command(dbi, S6D27A1_PANELCTL2, 0x00, 0x02, 0x03, 0x04, 0x05, 0x08, 0x00, 0x0c);
+
+ mipi_dbi_command(dbi, S6D27A1_MANPWR, 0x01, 0x00, 0x00, 0x08, 0x08, 0x02, 0x00);
+
+ mipi_dbi_command(dbi, S6D27A1_DISPCTL, 0x19, 0x00, 0x08, 0x0D, 0x03, 0x41, 0x3F);
+
+ mipi_dbi_command(dbi, S6D27A1_PWRCTL1, 0x00, 0x00, 0x00, 0x00, 0x55,
+ 0x44, 0x05, 0x88, 0x4B, 0x50);
+
+ mipi_dbi_command(dbi, S6D27A1_SRCCTL, 0x03, 0x09, 0x8A, 0x00, 0x01, 0x16);
+
+ mipi_dbi_command(dbi, S6D27A1_PANELCTL, 0x00, 0x05, 0x06, 0x07, 0x08,
+ 0x01, 0x09, 0x0D, 0x0A, 0x0E,
+ 0x0B, 0x0F, 0x0C, 0x10, 0x01,
+ 0x11, 0x12, 0x13, 0x14, 0x05,
+ 0x06, 0x07, 0x08, 0x01, 0x09,
+ 0x0D, 0x0A, 0x0E, 0x0B, 0x0F,
+ 0x0C, 0x10, 0x01, 0x11, 0x12,
+ 0x13, 0x14);
+
+ /* lock the level 2 control */
+ mipi_dbi_command(dbi, S6D27A1_PASSWD_L2, 0xA5, 0xA5);
+
+ s6d27a1_read_mtp_id(ctx);
+
+ return 0;
+}
+
+static int s6d27a1_power_off(struct s6d27a1 *ctx)
+{
+ /* Go into RESET and disable regulators */
+ gpiod_set_value_cansleep(ctx->reset, 1);
+ return regulator_bulk_disable(ARRAY_SIZE(ctx->regulators),
+ ctx->regulators);
+}
+
+static int s6d27a1_unprepare(struct drm_panel *panel)
+{
+ struct s6d27a1 *ctx = to_s6d27a1(panel);
+ struct mipi_dbi *dbi = &ctx->dbi;
+
+ mipi_dbi_command(dbi, MIPI_DCS_ENTER_SLEEP_MODE);
+ msleep(120);
+ return s6d27a1_power_off(to_s6d27a1(panel));
+}
+
+static int s6d27a1_disable(struct drm_panel *panel)
+{
+ struct s6d27a1 *ctx = to_s6d27a1(panel);
+ struct mipi_dbi *dbi = &ctx->dbi;
+
+ mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_OFF);
+ msleep(25);
+
+ return 0;
+}
+
+static int s6d27a1_prepare(struct drm_panel *panel)
+{
+ return s6d27a1_power_on(to_s6d27a1(panel));
+}
+
+static int s6d27a1_enable(struct drm_panel *panel)
+{
+ struct s6d27a1 *ctx = to_s6d27a1(panel);
+ struct mipi_dbi *dbi = &ctx->dbi;
+
+ mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_ON);
+
+ return 0;
+}
+
+static int s6d27a1_get_modes(struct drm_panel *panel,
+ struct drm_connector *connector)
+{
+ struct s6d27a1 *ctx = to_s6d27a1(panel);
+ struct drm_display_mode *mode;
+ static const u32 bus_format = MEDIA_BUS_FMT_RGB888_1X24;
+
+ mode = drm_mode_duplicate(connector->dev, &s6d27a1_480_800_mode);
+ if (!mode) {
+ dev_err(ctx->dev, "failed to add mode\n");
+ return -ENOMEM;
+ }
+
+ connector->display_info.bpc = 8;
+ connector->display_info.width_mm = mode->width_mm;
+ connector->display_info.height_mm = mode->height_mm;
+ connector->display_info.bus_flags =
+ DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE;
+ drm_display_info_set_bus_formats(&connector->display_info,
+ &bus_format, 1);
+
+ drm_mode_set_name(mode);
+ mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
+
+ drm_mode_probed_add(connector, mode);
+
+ return 1;
+}
+
+static const struct drm_panel_funcs s6d27a1_drm_funcs = {
+ .disable = s6d27a1_disable,
+ .unprepare = s6d27a1_unprepare,
+ .prepare = s6d27a1_prepare,
+ .enable = s6d27a1_enable,
+ .get_modes = s6d27a1_get_modes,
+};
+
+static int s6d27a1_probe(struct spi_device *spi)
+{
+ struct device *dev = &spi->dev;
+ struct s6d27a1 *ctx;
+ int ret;
+
+ ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
+ if (!ctx)
+ return -ENOMEM;
+
+ ctx->dev = dev;
+
+ /*
+ * VCI is the analog voltage supply
+ * VCCIO is the digital I/O voltage supply
+ */
+ ctx->regulators[0].supply = "vci";
+ ctx->regulators[1].supply = "vccio";
+ ret = devm_regulator_bulk_get(dev,
+ ARRAY_SIZE(ctx->regulators),
+ ctx->regulators);
+ if (ret)
+ return dev_err_probe(dev, ret, "failed to get regulators\n");
+
+ ctx->reset = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
+ if (IS_ERR(ctx->reset)) {
+ ret = PTR_ERR(ctx->reset);
+ return dev_err_probe(dev, ret, "no RESET GPIO\n");
+ }
+
+ ret = mipi_dbi_spi_init(spi, &ctx->dbi, NULL);
+ if (ret)
+ return dev_err_probe(dev, ret, "MIPI DBI init failed\n");
+
+ ctx->dbi.read_commands = s6d27a1_dbi_read_commands;
+
+ drm_panel_init(&ctx->panel, dev, &s6d27a1_drm_funcs,
+ DRM_MODE_CONNECTOR_DPI);
+
+ ret = drm_panel_of_backlight(&ctx->panel);
+ if (ret)
+ return dev_err_probe(dev, ret, "failed to add backlight\n");
+
+ spi_set_drvdata(spi, ctx);
+
+ drm_panel_add(&ctx->panel);
+
+ return 0;
+}
+
+static int s6d27a1_remove(struct spi_device *spi)
+{
+ struct s6d27a1 *ctx = spi_get_drvdata(spi);
+
+ drm_panel_remove(&ctx->panel);
+ return 0;
+}
+
+static const struct of_device_id s6d27a1_match[] = {
+ { .compatible = "samsung,s6d27a1", },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, s6d27a1_match);
+
+static struct spi_driver s6d27a1_driver = {
+ .probe = s6d27a1_probe,
+ .remove = s6d27a1_remove,
+ .driver = {
+ .name = "s6d27a1-panel",
+ .of_match_table = s6d27a1_match,
+ },
+};
+module_spi_driver(s6d27a1_driver);
+
+MODULE_AUTHOR("Markuss Broks <[email protected]>");
+MODULE_DESCRIPTION("Samsung S6D27A1 panel driver");
+MODULE_LICENSE("GPL v2");
--
2.32.0
Hi Markuss,
this is looking really good, the following is just nitty gritty details
I could fix while applying, we're mostly waiting for DT review now.
On Sat, Aug 7, 2021 at 3:31 PM Markuss Broks <[email protected]> wrote:
> + /*
> + * Exit sleep mode and initialize display - some hammering is
> + * necessary.
> + */
> + mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE);
> + mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE);
Check if this hammering is really necessary on s6d27a1, on Widechips
this is just a bug, what happens if you put just one of them?
> + msleep(50);
This should be msleep(120) on s6d27a1 (according to board-codina-mcde.c)
Yours,
Linus Walleij
On Sat, Aug 7, 2021 at 3:31 PM Markuss Broks <[email protected]> wrote:
> This adds device-tree bindings for the Samsung S6D27A1 RGB
> DPI display panel.
>
> Signed-off-by: Markuss Broks <[email protected]>
>
> v1 -> v2:
> changed additionalProperties to unevaluatedProperties;
> added vci-supply and vccio-supply as required;
These bindings look good to me:
Reviewed-by: Linus Walleij <[email protected]>
Will give DT reviewers some slack before applying the patches.
Yours,
Linus Walleij
On Sat, Aug 7, 2021 at 3:31 PM Markuss Broks <[email protected]> wrote:
> This adds a driver for Samsung S6D27A1 display controller and panel.
> This panel is found in the Samsung GT-I8160 mobile phone,
> and possibly some other mobile phones.
>
> This display needs manufacturer commands to configure it;
> the commands used in this driver were taken from downstream driver
> by Gareth Phillips; sadly, there is almost no documentation on what they
> actually do.
>
> This driver re-uses the DBI infrastructure to communicate with the display.
>
> This driver is heavily based on WideChips WS2401 display controller
> driver by Linus Walleij and on other panel drivers for reference.
>
> Signed-off-by: Markuss Broks <[email protected]>
>
> v2 -> v3:
Both v3 patches applied to drm-misc-next and pushed.
Yours,
Linus Walleij
On Sat, 07 Aug 2021 16:31:10 +0300, Markuss Broks wrote:
> This adds device-tree bindings for the Samsung S6D27A1 RGB
> DPI display panel.
>
> Signed-off-by: Markuss Broks <[email protected]>
>
> v1 -> v2:
> changed additionalProperties to unevaluatedProperties;
> added vci-supply and vccio-supply as required;
> ---
> .../display/panel/samsung,s6d27a1.yaml | 98 +++++++++++++++++++
> 1 file changed, 98 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6d27a1.yaml
>
Reviewed-by: Rob Herring <[email protected]>