During a USB cable disconnect, or soft disconnect scenario, a pending
SETUP transaction may not be completed, leading to the following
error:
dwc3 a600000.dwc3: timed out waiting for SETUP phase
If this occurs, then the entire pullup disable routine is skipped and
proper cleanup and halting of the controller does not complete.
Instead of returning an error (which is ignored from the UDC
perspective), allow the pullup disable routine to continue, which
will also handle disabling of EP0/1. This will end any active
transfers as well. Ensure to clear any delayed_status also, as the
timeout could happen within the STATUS stage.
Cc: <[email protected]>
Fixes: bb0147364850 ("usb: dwc3: gadget: don't clear RUN/STOP when it's invalid to do so")
Reviewed-by: Thinh Nguyen <[email protected]>
Signed-off-by: Wesley Cheng <[email protected]>
---
Changes in v5:
- Added Cc stable and fixes tag
Changes in v4:
- Fixed formatting and typos in commit text
- Removed braces due to the removal of the return statement
Changes in v3:
- Added suggestion by Thinh to change dev_err to dev_warn
Changes in v2:
- Removed calls to dwc3_ep0_end_control_data() and just allow the ep disables
on EP0 handle the proper ending of transfers.
- Ensure that delayed_status is cleared, as ran into enumeration issues if the
SETUP transaction fails on a STATUS stage. Saw delayed_status == TRUE on the
next connect, which blocked further SETUP transactions to be handled.
drivers/usb/dwc3/gadget.c | 7 +++----
1 file changed, 3 insertions(+), 4 deletions(-)
diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
index 5d084542718d..63f6d9f2a692 100644
--- a/drivers/usb/dwc3/gadget.c
+++ b/drivers/usb/dwc3/gadget.c
@@ -2428,10 +2428,8 @@ static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on)
ret = wait_for_completion_timeout(&dwc->ep0_in_setup,
msecs_to_jiffies(DWC3_PULL_UP_TIMEOUT));
- if (ret == 0) {
- dev_err(dwc->dev, "timed out waiting for SETUP phase\n");
- return -ETIMEDOUT;
- }
+ if (ret == 0)
+ dev_warn(dwc->dev, "timed out waiting for SETUP phase\n");
}
/*
@@ -2643,6 +2641,7 @@ static int __dwc3_gadget_start(struct dwc3 *dwc)
/* begin to receive SETUP packets */
dwc->ep0state = EP0_SETUP_PHASE;
dwc->link_state = DWC3_LINK_STATE_SS_DIS;
+ dwc->delayed_status = false;
dwc3_ep0_out_start(dwc);
dwc3_gadget_enable_irq(dwc);
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
Wesley Cheng <[email protected]> writes:
> During a USB cable disconnect, or soft disconnect scenario, a pending
> SETUP transaction may not be completed, leading to the following
> error:
>
> dwc3 a600000.dwc3: timed out waiting for SETUP phase
>
> If this occurs, then the entire pullup disable routine is skipped and
> proper cleanup and halting of the controller does not complete.
>
> Instead of returning an error (which is ignored from the UDC
> perspective), allow the pullup disable routine to continue, which
> will also handle disabling of EP0/1. This will end any active
> transfers as well. Ensure to clear any delayed_status also, as the
> timeout could happen within the STATUS stage.
>
> Cc: <[email protected]>
> Fixes: bb0147364850 ("usb: dwc3: gadget: don't clear RUN/STOP when it's invalid to do so")
> Reviewed-by: Thinh Nguyen <[email protected]>
> Signed-off-by: Wesley Cheng <[email protected]>
Acked-by: Felipe Balbi <[email protected]>
--
balbi