Add LPC uart routing driver and the device tree nodes.
Chia-Wei Wang (2):
soc: aspeed: Add LPC UART routing support
ARM: dts: aspeed: Add uart routing to device tree
arch/arm/boot/dts/aspeed-g5.dtsi | 6 +
arch/arm/boot/dts/aspeed-g6.dtsi | 6 +
drivers/soc/aspeed/Kconfig | 11 +
drivers/soc/aspeed/Makefile | 9 +-
drivers/soc/aspeed/aspeed-lpc-uart-routing.c | 621 +++++++++++++++++++
5 files changed, 649 insertions(+), 4 deletions(-)
create mode 100644 drivers/soc/aspeed/aspeed-lpc-uart-routing.c
--
2.17.1
Add driver support for the LPC UART routing control. Users can perform
runtime configuration of the RX muxes among the UART controllers and the
UART TXD/RXD IO pins. This is achieved through the exported sysfs interface.
Signed-off-by: Chia-Wei Wang <[email protected]>
---
drivers/soc/aspeed/Kconfig | 11 +
drivers/soc/aspeed/Makefile | 9 +-
drivers/soc/aspeed/aspeed-lpc-uart-routing.c | 621 +++++++++++++++++++
3 files changed, 637 insertions(+), 4 deletions(-)
create mode 100644 drivers/soc/aspeed/aspeed-lpc-uart-routing.c
diff --git a/drivers/soc/aspeed/Kconfig b/drivers/soc/aspeed/Kconfig
index 243ca196e6ad..6866757e6be2 100644
--- a/drivers/soc/aspeed/Kconfig
+++ b/drivers/soc/aspeed/Kconfig
@@ -24,6 +24,17 @@ config ASPEED_LPC_SNOOP
allows the BMC to listen on and save the data written by
the host to an arbitrary LPC I/O port.
+config ASPEED_LPC_UART_ROUTING
+ tristate "ASPEED LPC uart routing control"
+ select REGMAP
+ select MFD_SYSCON
+ default ARCH_ASPEED
+ help
+ Provides a driver to control the LPC UART routing paths.
+ An sysfs interface is exported allowing users to perform
+ runtime configuration of the RX muxes between the UART
+ controllers and I/O pins.
+
config ASPEED_P2A_CTRL
tristate "ASPEED P2A (VGA MMIO to BMC) bridge control"
select REGMAP
diff --git a/drivers/soc/aspeed/Makefile b/drivers/soc/aspeed/Makefile
index fcab7192e1a4..87ad6578ddbb 100644
--- a/drivers/soc/aspeed/Makefile
+++ b/drivers/soc/aspeed/Makefile
@@ -1,5 +1,6 @@
# SPDX-License-Identifier: GPL-2.0-only
-obj-$(CONFIG_ASPEED_LPC_CTRL) += aspeed-lpc-ctrl.o
-obj-$(CONFIG_ASPEED_LPC_SNOOP) += aspeed-lpc-snoop.o
-obj-$(CONFIG_ASPEED_P2A_CTRL) += aspeed-p2a-ctrl.o
-obj-$(CONFIG_ASPEED_SOCINFO) += aspeed-socinfo.o
+obj-$(CONFIG_ASPEED_LPC_CTRL) += aspeed-lpc-ctrl.o
+obj-$(CONFIG_ASPEED_LPC_SNOOP) += aspeed-lpc-snoop.o
+obj-$(CONFIG_ASPEED_LPC_UART_ROUTING) += aspeed-lpc-uart-routing.o
+obj-$(CONFIG_ASPEED_P2A_CTRL) += aspeed-p2a-ctrl.o
+obj-$(CONFIG_ASPEED_SOCINFO) += aspeed-socinfo.o
diff --git a/drivers/soc/aspeed/aspeed-lpc-uart-routing.c b/drivers/soc/aspeed/aspeed-lpc-uart-routing.c
new file mode 100644
index 000000000000..141d0d08b4ff
--- /dev/null
+++ b/drivers/soc/aspeed/aspeed-lpc-uart-routing.c
@@ -0,0 +1,621 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (c) 2018 Google LLC
+ * Copyright (c) 2021 Aspeed Technology Inc.
+ */
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/of_address.h>
+#include <linux/of_platform.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+#include <linux/platform_device.h>
+
+/* register offsets */
+#define HICR9 0x98
+#define HICRA 0x9c
+
+/* attributes options */
+#define UART_ROUTING_IO1 "io1"
+#define UART_ROUTING_IO2 "io2"
+#define UART_ROUTING_IO3 "io3"
+#define UART_ROUTING_IO4 "io4"
+#define UART_ROUTING_IO5 "io5"
+#define UART_ROUTING_IO6 "io6"
+#define UART_ROUTING_IO10 "io10"
+#define UART_ROUTING_UART1 "uart1"
+#define UART_ROUTING_UART2 "uart2"
+#define UART_ROUTING_UART3 "uart3"
+#define UART_ROUTING_UART4 "uart4"
+#define UART_ROUTING_UART5 "uart5"
+#define UART_ROUTING_UART6 "uart6"
+#define UART_ROUTING_UART10 "uart10"
+#define UART_ROUTING_RES "reserved"
+
+struct aspeed_uart_routing {
+ struct regmap *map;
+ spinlock_t lock;
+ struct attribute_group const *attr_grp;
+};
+
+struct aspeed_uart_routing_selector {
+ struct device_attribute dev_attr;
+ uint32_t reg;
+ uint32_t mask;
+ uint32_t shift;
+ const char *const options[];
+};
+
+#define to_routing_selector(_dev_attr) \
+ container_of(_dev_attr, struct aspeed_uart_routing_selector, dev_attr)
+
+static ssize_t aspeed_uart_routing_show(struct device *dev,
+ struct device_attribute *attr,
+ char *buf);
+
+static ssize_t aspeed_uart_routing_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count);
+
+#define ROUTING_ATTR(_name) { \
+ .attr = {.name = _name, \
+ .mode = VERIFY_OCTAL_PERMISSIONS(0644) }, \
+ .show = aspeed_uart_routing_show, \
+ .store = aspeed_uart_routing_store, \
+}
+
+/* routing selector for AST25xx */
+static struct aspeed_uart_routing_selector ast2500_io6_sel = {
+ .dev_attr = ROUTING_ATTR(UART_ROUTING_IO6),
+ .reg = HICR9,
+ .shift = 8,
+ .mask = 0xf,
+ .options = {
+ UART_ROUTING_UART1,
+ UART_ROUTING_UART2,
+ UART_ROUTING_UART3,
+ UART_ROUTING_UART4,
+ UART_ROUTING_UART5,
+ UART_ROUTING_IO1,
+ UART_ROUTING_IO2,
+ UART_ROUTING_IO3,
+ UART_ROUTING_IO4,
+ UART_ROUTING_IO5,
+ NULL,
+ },
+};
+
+static struct aspeed_uart_routing_selector ast2500_uart5_sel = {
+ .dev_attr = ROUTING_ATTR(UART_ROUTING_UART5),
+ .reg = HICRA,
+ .shift = 28,
+ .mask = 0xf,
+ .options = {
+ UART_ROUTING_IO5,
+ UART_ROUTING_IO1,
+ UART_ROUTING_IO2,
+ UART_ROUTING_IO3,
+ UART_ROUTING_IO4,
+ UART_ROUTING_UART1,
+ UART_ROUTING_UART2,
+ UART_ROUTING_UART3,
+ UART_ROUTING_UART4,
+ UART_ROUTING_IO6,
+ NULL,
+ },
+};
+
+static struct aspeed_uart_routing_selector ast2500_uart4_sel = {
+ .dev_attr = ROUTING_ATTR(UART_ROUTING_UART4),
+ .reg = HICRA,
+ .shift = 25,
+ .mask = 0x7,
+ .options = {
+ UART_ROUTING_IO4,
+ UART_ROUTING_IO1,
+ UART_ROUTING_IO2,
+ UART_ROUTING_IO3,
+ UART_ROUTING_UART1,
+ UART_ROUTING_UART2,
+ UART_ROUTING_UART3,
+ UART_ROUTING_IO6,
+ NULL,
+ },
+};
+
+static struct aspeed_uart_routing_selector ast2500_uart3_sel = {
+ .dev_attr = ROUTING_ATTR(UART_ROUTING_UART3),
+ .reg = HICRA,
+ .shift = 22,
+ .mask = 0x7,
+ .options = {
+ UART_ROUTING_IO3,
+ UART_ROUTING_IO4,
+ UART_ROUTING_IO1,
+ UART_ROUTING_IO2,
+ UART_ROUTING_UART4,
+ UART_ROUTING_UART1,
+ UART_ROUTING_UART2,
+ UART_ROUTING_IO6,
+ NULL,
+ },
+};
+
+static struct aspeed_uart_routing_selector ast2500_uart2_sel = {
+ .dev_attr = ROUTING_ATTR(UART_ROUTING_UART2),
+ .reg = HICRA,
+ .shift = 19,
+ .mask = 0x7,
+ .options = {
+ UART_ROUTING_IO2,
+ UART_ROUTING_IO3,
+ UART_ROUTING_IO4,
+ UART_ROUTING_IO1,
+ UART_ROUTING_UART3,
+ UART_ROUTING_UART4,
+ UART_ROUTING_UART1,
+ UART_ROUTING_IO6,
+ NULL,
+ },
+};
+
+static struct aspeed_uart_routing_selector ast2500_uart1_sel = {
+ .dev_attr = ROUTING_ATTR(UART_ROUTING_UART1),
+ .reg = HICRA,
+ .shift = 16,
+ .mask = 0x7,
+ .options = {
+ UART_ROUTING_IO1,
+ UART_ROUTING_IO2,
+ UART_ROUTING_IO3,
+ UART_ROUTING_IO4,
+ UART_ROUTING_UART2,
+ UART_ROUTING_UART3,
+ UART_ROUTING_UART4,
+ UART_ROUTING_IO6,
+ NULL,
+ },
+};
+
+static struct aspeed_uart_routing_selector ast2500_io5_sel = {
+ .dev_attr = ROUTING_ATTR(UART_ROUTING_IO5),
+ .reg = HICRA,
+ .shift = 12,
+ .mask = 0x7,
+ .options = {
+ UART_ROUTING_UART5,
+ UART_ROUTING_UART1,
+ UART_ROUTING_UART2,
+ UART_ROUTING_UART3,
+ UART_ROUTING_UART4,
+ UART_ROUTING_IO1,
+ UART_ROUTING_IO3,
+ UART_ROUTING_IO6,
+ NULL,
+ },
+};
+
+static struct aspeed_uart_routing_selector ast2500_io4_sel = {
+ .dev_attr = ROUTING_ATTR(UART_ROUTING_IO4),
+ .reg = HICRA,
+ .shift = 9,
+ .mask = 0x7,
+ .options = {
+ UART_ROUTING_UART4,
+ UART_ROUTING_UART5,
+ UART_ROUTING_UART1,
+ UART_ROUTING_UART2,
+ UART_ROUTING_UART3,
+ UART_ROUTING_IO1,
+ UART_ROUTING_IO2,
+ UART_ROUTING_IO6,
+ NULL,
+ },
+};
+
+static struct aspeed_uart_routing_selector ast2500_io3_sel = {
+ .dev_attr = ROUTING_ATTR(UART_ROUTING_IO3),
+ .reg = HICRA,
+ .shift = 6,
+ .mask = 0x7,
+ .options = {
+ UART_ROUTING_UART3,
+ UART_ROUTING_UART4,
+ UART_ROUTING_UART5,
+ UART_ROUTING_UART1,
+ UART_ROUTING_UART2,
+ UART_ROUTING_IO1,
+ UART_ROUTING_IO2,
+ UART_ROUTING_IO6,
+ NULL,
+ },
+};
+
+static struct aspeed_uart_routing_selector ast2500_io2_sel = {
+ .dev_attr = ROUTING_ATTR(UART_ROUTING_IO2),
+ .reg = HICRA,
+ .shift = 3,
+ .mask = 0x7,
+ .options = {
+ UART_ROUTING_UART2,
+ UART_ROUTING_UART3,
+ UART_ROUTING_UART4,
+ UART_ROUTING_UART5,
+ UART_ROUTING_UART1,
+ UART_ROUTING_IO3,
+ UART_ROUTING_IO4,
+ UART_ROUTING_IO6,
+ NULL,
+ },
+};
+
+static struct aspeed_uart_routing_selector ast2500_io1_sel = {
+ .dev_attr = ROUTING_ATTR(UART_ROUTING_IO1),
+ .reg = HICRA,
+ .shift = 0,
+ .mask = 0x7,
+ .options = {
+ UART_ROUTING_UART1,
+ UART_ROUTING_UART2,
+ UART_ROUTING_UART3,
+ UART_ROUTING_UART4,
+ UART_ROUTING_UART5,
+ UART_ROUTING_IO3,
+ UART_ROUTING_IO4,
+ UART_ROUTING_IO6,
+ NULL,
+ },
+};
+
+static struct attribute *ast2500_uart_routing_attrs[] = {
+ &ast2500_io6_sel.dev_attr.attr,
+ &ast2500_uart5_sel.dev_attr.attr,
+ &ast2500_uart4_sel.dev_attr.attr,
+ &ast2500_uart3_sel.dev_attr.attr,
+ &ast2500_uart2_sel.dev_attr.attr,
+ &ast2500_uart1_sel.dev_attr.attr,
+ &ast2500_io5_sel.dev_attr.attr,
+ &ast2500_io4_sel.dev_attr.attr,
+ &ast2500_io3_sel.dev_attr.attr,
+ &ast2500_io2_sel.dev_attr.attr,
+ &ast2500_io1_sel.dev_attr.attr,
+ NULL,
+};
+
+static const struct attribute_group ast2500_uart_routing_attr_group = {
+ .attrs = ast2500_uart_routing_attrs,
+};
+
+/* routing selector for AST26xx */
+static struct aspeed_uart_routing_selector ast2600_uart10_sel = {
+ .dev_attr = ROUTING_ATTR(UART_ROUTING_UART10),
+ .reg = HICR9,
+ .shift = 12,
+ .mask = 0xf,
+ .options = {
+ UART_ROUTING_IO10,
+ UART_ROUTING_IO1,
+ UART_ROUTING_IO2,
+ UART_ROUTING_IO3,
+ UART_ROUTING_IO4,
+ UART_ROUTING_RES,
+ UART_ROUTING_UART1,
+ UART_ROUTING_UART2,
+ UART_ROUTING_UART3,
+ UART_ROUTING_UART4,
+ NULL,
+ },
+};
+
+static struct aspeed_uart_routing_selector ast2600_io10_sel = {
+ .dev_attr = ROUTING_ATTR(UART_ROUTING_IO10),
+ .reg = HICR9,
+ .shift = 8,
+ .mask = 0xf,
+ .options = {
+ UART_ROUTING_UART1,
+ UART_ROUTING_UART2,
+ UART_ROUTING_UART3,
+ UART_ROUTING_UART4,
+ UART_ROUTING_RES,
+ UART_ROUTING_IO1,
+ UART_ROUTING_IO2,
+ UART_ROUTING_IO3,
+ UART_ROUTING_IO4,
+ UART_ROUTING_RES,
+ UART_ROUTING_UART10,
+ NULL,
+ },
+};
+
+static struct aspeed_uart_routing_selector ast2600_uart4_sel = {
+ .dev_attr = ROUTING_ATTR(UART_ROUTING_UART4),
+ .reg = HICRA,
+ .shift = 25,
+ .mask = 0x7,
+ .options = {
+ UART_ROUTING_IO4,
+ UART_ROUTING_IO1,
+ UART_ROUTING_IO2,
+ UART_ROUTING_IO3,
+ UART_ROUTING_UART1,
+ UART_ROUTING_UART2,
+ UART_ROUTING_UART3,
+ UART_ROUTING_IO10,
+ NULL,
+ },
+};
+
+static struct aspeed_uart_routing_selector ast2600_uart3_sel = {
+ .dev_attr = ROUTING_ATTR(UART_ROUTING_UART3),
+ .reg = HICRA,
+ .shift = 22,
+ .mask = 0x7,
+ .options = {
+ UART_ROUTING_IO3,
+ UART_ROUTING_IO4,
+ UART_ROUTING_IO1,
+ UART_ROUTING_IO2,
+ UART_ROUTING_UART4,
+ UART_ROUTING_UART1,
+ UART_ROUTING_UART2,
+ UART_ROUTING_IO10,
+ NULL,
+ },
+};
+
+static struct aspeed_uart_routing_selector ast2600_uart2_sel = {
+ .dev_attr = ROUTING_ATTR(UART_ROUTING_UART2),
+ .reg = HICRA,
+ .shift = 19,
+ .mask = 0x7,
+ .options = {
+ UART_ROUTING_IO2,
+ UART_ROUTING_IO3,
+ UART_ROUTING_IO4,
+ UART_ROUTING_IO1,
+ UART_ROUTING_UART3,
+ UART_ROUTING_UART4,
+ UART_ROUTING_UART1,
+ UART_ROUTING_IO10,
+ NULL,
+ },
+};
+
+static struct aspeed_uart_routing_selector ast2600_uart1_sel = {
+ .dev_attr = ROUTING_ATTR(UART_ROUTING_UART1),
+ .reg = HICRA,
+ .shift = 16,
+ .mask = 0x7,
+ .options = {
+ UART_ROUTING_IO1,
+ UART_ROUTING_IO2,
+ UART_ROUTING_IO3,
+ UART_ROUTING_IO4,
+ UART_ROUTING_UART2,
+ UART_ROUTING_UART3,
+ UART_ROUTING_UART4,
+ UART_ROUTING_IO10,
+ NULL,
+ },
+};
+
+static struct aspeed_uart_routing_selector ast2600_io4_sel = {
+ .dev_attr = ROUTING_ATTR(UART_ROUTING_IO4),
+ .reg = HICRA,
+ .shift = 9,
+ .mask = 0x7,
+ .options = {
+ UART_ROUTING_UART4,
+ UART_ROUTING_UART10,
+ UART_ROUTING_UART1,
+ UART_ROUTING_UART2,
+ UART_ROUTING_UART3,
+ UART_ROUTING_IO1,
+ UART_ROUTING_IO2,
+ UART_ROUTING_IO10,
+ NULL,
+ },
+};
+
+static struct aspeed_uart_routing_selector ast2600_io3_sel = {
+ .dev_attr = ROUTING_ATTR(UART_ROUTING_IO3),
+ .reg = HICRA,
+ .shift = 6,
+ .mask = 0x7,
+ .options = {
+ UART_ROUTING_UART3,
+ UART_ROUTING_UART4,
+ UART_ROUTING_UART10,
+ UART_ROUTING_UART1,
+ UART_ROUTING_UART2,
+ UART_ROUTING_IO1,
+ UART_ROUTING_IO2,
+ UART_ROUTING_IO10,
+ NULL,
+ },
+};
+
+static struct aspeed_uart_routing_selector ast2600_io2_sel = {
+ .dev_attr = ROUTING_ATTR(UART_ROUTING_IO2),
+ .reg = HICRA,
+ .shift = 3,
+ .mask = 0x7,
+ .options = {
+ UART_ROUTING_UART2,
+ UART_ROUTING_UART3,
+ UART_ROUTING_UART4,
+ UART_ROUTING_UART10,
+ UART_ROUTING_UART1,
+ UART_ROUTING_IO3,
+ UART_ROUTING_IO4,
+ UART_ROUTING_IO10,
+ NULL,
+ },
+};
+
+static struct aspeed_uart_routing_selector ast2600_io1_sel = {
+ .dev_attr = ROUTING_ATTR(UART_ROUTING_IO1),
+ .reg = HICRA,
+ .shift = 0,
+ .mask = 0x7,
+ .options = {
+ UART_ROUTING_UART1,
+ UART_ROUTING_UART2,
+ UART_ROUTING_UART3,
+ UART_ROUTING_UART4,
+ UART_ROUTING_UART10,
+ UART_ROUTING_IO3,
+ UART_ROUTING_IO4,
+ UART_ROUTING_IO10,
+ NULL,
+ },
+};
+
+static struct attribute *ast2600_uart_routing_attrs[] = {
+ &ast2600_uart10_sel.dev_attr.attr,
+ &ast2600_io10_sel.dev_attr.attr,
+ &ast2600_uart4_sel.dev_attr.attr,
+ &ast2600_uart3_sel.dev_attr.attr,
+ &ast2600_uart2_sel.dev_attr.attr,
+ &ast2600_uart1_sel.dev_attr.attr,
+ &ast2600_io4_sel.dev_attr.attr,
+ &ast2600_io3_sel.dev_attr.attr,
+ &ast2600_io2_sel.dev_attr.attr,
+ &ast2600_io1_sel.dev_attr.attr,
+ NULL,
+};
+
+static const struct attribute_group ast2600_uart_routing_attr_group = {
+ .attrs = ast2600_uart_routing_attrs,
+};
+
+static ssize_t aspeed_uart_routing_show(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct aspeed_uart_routing *uart_routing = dev_get_drvdata(dev);
+ struct aspeed_uart_routing_selector *sel = to_routing_selector(attr);
+ int val, pos, len;
+
+ regmap_read(uart_routing->map, sel->reg, &val);
+ val = (val >> sel->shift) & sel->mask;
+
+ len = 0;
+ for (pos = 0; sel->options[pos] != NULL; ++pos) {
+ if (pos == val) {
+ len += snprintf(buf + len, PAGE_SIZE - 1 - len,
+ "[%s] ", sel->options[pos]);
+ } else {
+ len += snprintf(buf + len, PAGE_SIZE - 1 - len,
+ "%s ", sel->options[pos]);
+ }
+ }
+
+ if (val >= pos) {
+ len += snprintf(buf + len, PAGE_SIZE - 1 - len,
+ "[unknown(%d)]", val);
+ }
+
+ len += snprintf(buf + len, PAGE_SIZE - 1 - len, "\n");
+
+ return len;
+}
+
+static ssize_t aspeed_uart_routing_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ unsigned long flags;
+ struct aspeed_uart_routing *uart_routing = dev_get_drvdata(dev);
+ struct aspeed_uart_routing_selector *sel = to_routing_selector(attr);
+ int val;
+
+ val = match_string(sel->options, -1, buf);
+ if (val < 0) {
+ dev_err(dev, "invalid value \"%s\"\n", buf);
+ return -EINVAL;
+ }
+
+ spin_lock_irqsave(&uart_routing->lock, flags);
+
+ regmap_update_bits(uart_routing->map, sel->reg,
+ (sel->mask << sel->shift),
+ (val & sel->mask) << sel->shift);
+
+ spin_unlock_irqrestore(&uart_routing->lock, flags);
+
+ return count;
+}
+
+static int aspeed_uart_routing_probe(struct platform_device *pdev)
+{
+ int rc;
+ struct device *dev = &pdev->dev;
+ struct aspeed_uart_routing *uart_routing;
+
+ uart_routing = devm_kzalloc(&pdev->dev,
+ sizeof(*uart_routing),
+ GFP_KERNEL);
+ if (!uart_routing) {
+ dev_err(dev, "cannot allocate memory\n");
+ return -ENOMEM;
+ }
+
+ uart_routing->map = syscon_node_to_regmap(dev->parent->of_node);
+ if (IS_ERR(uart_routing->map)) {
+ dev_err(dev, "cannot get regmap\n");
+ return PTR_ERR(uart_routing->map);
+ }
+
+ uart_routing->attr_grp = of_device_get_match_data(dev);
+
+ spin_lock_init(&uart_routing->lock);
+
+ rc = sysfs_create_group(&dev->kobj,
+ uart_routing->attr_grp);
+ if (rc < 0)
+ return rc;
+
+ dev_set_drvdata(dev, uart_routing);
+
+ dev_info(dev, "module loaded\n");
+
+ return 0;
+}
+
+static int aspeed_uart_routing_remove(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct aspeed_uart_routing *uart_routing = platform_get_drvdata(pdev);
+
+ sysfs_remove_group(&dev->kobj,
+ uart_routing->attr_grp);
+
+ return 0;
+}
+
+static const struct of_device_id aspeed_uart_routing_table[] = {
+ { .compatible = "aspeed,ast2500-lpc-uart-routing",
+ .data = &ast2500_uart_routing_attr_group },
+ { .compatible = "aspeed,ast2600-lpc-uart-routing",
+ .data = &ast2600_uart_routing_attr_group },
+ { },
+};
+
+static struct platform_driver aspeed_uart_routing_driver = {
+ .driver = {
+ .name = "aspeed-lpc-uart-routing",
+ .of_match_table = aspeed_uart_routing_table,
+ },
+ .probe = aspeed_uart_routing_probe,
+ .remove = aspeed_uart_routing_remove,
+};
+
+module_platform_driver(aspeed_uart_routing_driver);
+
+MODULE_AUTHOR("Oskar Senft <[email protected]>");
+MODULE_AUTHOR("Chia-Wei Wang <[email protected]>");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Driver to configure Aspeed UART routing");
--
2.17.1
On Wed, 1 Sept 2021 at 06:22, Chia-Wei Wang <[email protected]> wrote:
>
> Add LPC uart routing driver and the device tree nodes.
Thanks for submitting this driver. There are many parties who are
interested in this, so hopefully they can step forward and review.
Is this LPC UART routing, or UART routing in general? I know the
register to control the routing is hidden in the LPC space, but I
thought it was just general routing. I would drop the LPC part of the
name.
You also need to update the bindings document with the new compatible
string. Send a patch for
Documentation/devicetree/bindings/mfd/aspeed-lpc.txt.
Cheers,
Joel
>
> Chia-Wei Wang (2):
> soc: aspeed: Add LPC UART routing support
> ARM: dts: aspeed: Add uart routing to device tree
>
> arch/arm/boot/dts/aspeed-g5.dtsi | 6 +
> arch/arm/boot/dts/aspeed-g6.dtsi | 6 +
> drivers/soc/aspeed/Kconfig | 11 +
> drivers/soc/aspeed/Makefile | 9 +-
> drivers/soc/aspeed/aspeed-lpc-uart-routing.c | 621 +++++++++++++++++++
> 5 files changed, 649 insertions(+), 4 deletions(-)
> create mode 100644 drivers/soc/aspeed/aspeed-lpc-uart-routing.c
>
> --
> 2.17.1
>