Add support for new home automation devices.
JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features:
- DIN Rail Mounting
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB LPDDR4
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE
JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation controller with the following features:
- square plastic case
- Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1GB LPDDR4
- 8/16GB eMMC flash
- 2 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- MicroSD 2.x/3.x/4.x DS/HS cards.
- 1 x gpio LED
- ADC user Button
- DC source 5V microUSB
Changes from v4:
- add 1wire-gpio node in meson-axg-jethome-jethub-j100.dts
Changes from v3:
- add pinctrl for spicc1 in meson-axg-jethome-jethub-j100.dts
Changes from v2:
- add new vendor to vendor-prefixes
- sync board compatible dt-bindings to jethome,jethub-*
- fix efuse fields
- fix gpio-line-names
- fix spaces and blank lines
- recheck via checkpatch
Changes from v1:
- rearrange patches
- add SPDX license and copyright header
- remove attributes without bindings
- small fixes with spaces
Vyacheslav Bocharov (4):
dt-bindings: arm: amlogic: add bindings for Jethub D1/H1
dt-bindings: vendor-prefixes: add jethome prefix
arm64: dts: meson-gxl: add support for JetHub H1
arm64: dts: meson-axg: add support for JetHub D1
.../devicetree/bindings/arm/amlogic.yaml | 2 +
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
arch/arm64/boot/dts/amlogic/Makefile | 2 +
.../amlogic/meson-axg-jethome-jethub-j100.dts | 361 ++++++++++++++++++
.../meson-gxl-s905w-jethome-jethub-j80.dts | 241 ++++++++++++
5 files changed, 608 insertions(+)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts
--
2.30.2
JetHome is a series of home automation controllers:
- Jethub D1 based on Amlogic A113X
- Jethub H1 based on AmLogic S905W
Signed-off-by: Vyacheslav Bocharov <[email protected]>
Acked-by: Rob Herring <[email protected]>
---
Documentation/devicetree/bindings/arm/amlogic.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
index 6423377710ee..b223d7829c3d 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@@ -86,6 +86,7 @@ properties:
- enum:
- amlogic,p281
- oranth,tx3-mini
+ - jethome,jethub-j80
- const: amlogic,s905w
- const: amlogic,meson-gxl
@@ -133,6 +134,7 @@ properties:
items:
- enum:
- amlogic,s400
+ - jethome,jethub-j100
- const: amlogic,a113d
- const: amlogic,meson-axg
--
2.30.2
JetHome is trademark of IP Sokolov P.A., manufacturer of home automation
devices.
Signed-off-by: Vyacheslav Bocharov <[email protected]>
---
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index a867f7102c35..c52f0d3261bb 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -577,6 +577,8 @@ patternProperties:
description: JEDEC Solid State Technology Association
"^jesurun,.*":
description: Shenzhen Jesurun Electronics Business Dept.
+ "^jethome,.*":
+ description: JetHome (IP Sokolov P.A.)
"^jianda,.*":
description: Jiandangjing Technology Co., Ltd.
"^kam,.*":
--
2.30.2
JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation
controller with the following features:
- square plastic case
- Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1GB LPDDR4
- 8/16GB eMMC flash
- 2 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power
and Zigbee 3.0 support.
- MicroSD 2.x/3.x/4.x DS/HS cards.
- 1 x gpio LED
- ADC user Button
- DC source 5V microUSB
Signed-off-by: Vyacheslav Bocharov <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
---
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../meson-gxl-s905w-jethome-jethub-j80.dts | 241 ++++++++++++++++++
2 files changed, 242 insertions(+)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index faa0a79a34f5..2c3ce7c401a5 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -38,6 +38,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-p281.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-tx3-mini.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-libretech-pc.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-jethome-jethub-j80.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxm-khadas-vim2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxm-mecool-kiii-pro.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxm-minix-neo-u9h.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts
new file mode 100644
index 000000000000..6eafb908695f
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts
@@ -0,0 +1,241 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Vyacheslav Bocharov <[email protected]>
+ * Copyright (c) 2020 JetHome
+ * Author: Aleksandr Kazantsev <[email protected]>
+ * Author: Alexey Shevelkin <[email protected]>
+ * Author: Vyacheslav Bocharov <[email protected]>
+ */
+
+/dts-v1/;
+
+#include "meson-gxl.dtsi"
+
+/ {
+ compatible = "jethome,jethub-j80", "amlogic,s905w", "amlogic,meson-gxl";
+ model = "JetHome JetHub J80";
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ reserved-memory {
+ linux,cma {
+ size = <0x0 0x1000000>;
+ };
+ };
+
+ aliases {
+ serial0 = &uart_AO; /* Console */
+ serial1 = &uart_A; /* Bluetooth */
+ serial2 = &uart_AO_B; /* Wireless module 1 */
+ serial3 = &uart_C; /* Wireless module 2 */
+ ethernet0 = ðmac;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ vddio_ao18: regulator-vddio_ao18 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vddio_boot: regulator-vddio_boot {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_BOOT";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vddao_3v3: regulator-vddao_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vcc_3v3: regulator-vcc_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+ };
+
+ wifi32k: wifi32k {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+ clocks = <&wifi32k>;
+ clock-names = "ext_clock";
+ };
+};
+
+&efuse {
+ bt_mac: bt_mac@6 {
+ reg = <0x6 0x6>;
+ };
+
+ wifi_mac: wifi_mac@C {
+ reg = <0xc 0x6>;
+ };
+};
+
+&sn {
+ reg = <0x32 0x20>;
+};
+
+ð_mac {
+ reg = <0x0 0x6>;
+};
+
+&bid {
+ reg = <0x12 0x20>;
+};
+
+&usb {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&pwm_ef {
+ status = "okay";
+ pinctrl-0 = <&pwm_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&clkc CLKID_FCLK_DIV4>;
+ clock-names = "clkin0";
+};
+
+&saradc {
+ status = "okay";
+ vref-supply = <&vddio_ao18>;
+};
+
+/* Wireless SDIO Module */
+&sd_emmc_a {
+ status = "okay";
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <50000000>;
+
+ non-removable;
+ disable-wp;
+
+ /* WiFi firmware requires power to be kept while in suspend */
+ keep-power-in-suspend;
+
+ mmc-pwrseq = <&sdio_pwrseq>;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
+
+/* SD card */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <50000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ max-frequency = <200000000>;
+ non-removable;
+ disable-wp;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
+
+/* Console UART */
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+/* S905W only has access to its internal PHY */
+ðmac {
+ status = "okay";
+ phy-mode = "rmii";
+ phy-handle = <&internal_phy>;
+};
+
+&internal_phy {
+ status = "okay";
+ pinctrl-0 = <ð_link_led_pins>, <ð_act_led_pins>;
+ pinctrl-names = "default";
+};
+
+&uart_A {
+ status = "okay";
+ pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+};
+
+&uart_C {
+ status = "okay";
+ pinctrl-0 = <&uart_c_pins>;
+ pinctrl-names = "default";
+};
+
+&uart_AO_B {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_b_pins>, <&uart_ao_b_cts_rts_pins>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+};
+
+&i2c_B {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c_b_pins>;
+
+ pcf8563: pcf8563@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ status = "okay";
+ };
+};
--
2.30.2
JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation
controller with the following features:
- DIN Rail Mounting
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB LPDDR4
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac,
Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power
and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE
Changes from v4:
- add node for 1wire-gpio for JetHub D1 v2 device
Signed-off-by: Vyacheslav Bocharov <[email protected]>
---
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../amlogic/meson-axg-jethome-jethub-j100.dts | 361 ++++++++++++++++++
2 files changed, 362 insertions(+)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 2c3ce7c401a5..3ba6f58b9833 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -1,5 +1,6 @@
# SPDX-License-Identifier: GPL-2.0
dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j100.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
new file mode 100644
index 000000000000..c25b03a91e12
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
@@ -0,0 +1,361 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Vyacheslav Bocharov <[email protected]>
+ * Copyright (c) 2020 JetHome
+ * Author: Aleksandr Kazantsev <[email protected]>
+ * Author: Alexey Shevelkin <[email protected]>
+ * Author: Vyacheslav Bocharov <[email protected]>
+ */
+
+/dts-v1/;
+
+#include "meson-axg.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+ compatible = "jethome,jethub-j100", "amlogic,a113d", "amlogic,meson-axg";
+ model = "JetHome JetHub J100";
+ aliases {
+ serial0 = &uart_AO; /* Console */
+ serial1 = &uart_AO_B; /* External UART (Wireless Module) */
+ ethernet0 = ðmac;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ /* 1024MB RAM */
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ reserved-memory {
+ linux,cma {
+ size = <0x0 0x400000>;
+ };
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+ };
+
+ vcc_3v3: regulator-vcc_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vcc_5v: regulator-vcc_5v {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ vddao_3v3: regulator-vddao_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_5v>;
+ regulator-always-on;
+ };
+
+ vddio_ao18: regulator-vddio_ao18 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vddio_boot: regulator-vddio_boot {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_BOOT";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ usb_pwr: regulator-usb_pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "USB_PWR";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_5v>;
+ regulator-always-on;
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
+ clocks = <&wifi32k>;
+ clock-names = "ext_clock";
+ };
+
+ wifi32k: wifi32k {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ pwms = <&pwm_ab 0 30518 0>; /* PWM_A at 32.768KHz */
+ };
+
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+ thermal-sensors = <&scpi_sensors 0>;
+ trips {
+ cpu_passive: cpu-passive {
+ temperature = <70000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "passive";
+ };
+
+ cpu_hot: cpu-hot {
+ temperature = <80000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "hot";
+ };
+
+ cpu_critical: cpu-critical {
+ temperature = <100000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "critical";
+ };
+ };
+ };
+
+ cpu_cooling_maps: cooling-maps {
+ map0 {
+ trip = <&cpu_passive>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+
+ map1 {
+ trip = <&cpu_hot>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+ onewire {
+ compatible = "w1-gpio";
+ gpios = <&gpio GPIOA_14 GPIO_ACTIVE_HIGH>;
+ #gpio-cells = <1>;
+ };
+};
+
+&efuse {
+ sn: sn@32 {
+ reg = <0x32 0x20>;
+ };
+
+ eth_mac: eth_mac@0 {
+ reg = <0x0 0x6>;
+ };
+
+ bt_mac: bt_mac@6 {
+ reg = <0x6 0x6>;
+ };
+
+ wifi_mac: wifi_mac@c {
+ reg = <0xc 0x6>;
+ };
+
+ bid: bid@12 {
+ reg = <0x12 0x20>;
+ };
+};
+
+ðmac {
+ status = "okay";
+ pinctrl-0 = <ð_rmii_x_pins>;
+ pinctrl-names = "default";
+ phy-handle = <ð_phy0>;
+ phy-mode = "rmii";
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* ICPlus IP101A/G Ethernet PHY (vendor_id=0x0243, model_id=0x0c54) */
+ eth_phy0: ethernet-phy@0 {
+ /* compatible = "ethernet-phy-id0243.0c54";*/
+ max-speed = <100>;
+ reg = <0>;
+
+ reset-assert-us = <10000>;
+ reset-deassert-us = <10000>;
+ reset-gpios = <&gpio GPIOZ_5 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+/* Internal I2C bus (on CPU module) */
+&i2c1 {
+ status = "okay";
+ pinctrl-0 = <&i2c1_z_pins>;
+ pinctrl-names = "default";
+
+ /* RTC */
+ pcf8563: pcf8563@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ status = "okay";
+ };
+};
+
+/* Peripheral I2C bus (on motherboard) */
+&i2c_AO {
+ status = "okay";
+ pinctrl-0 = <&i2c_ao_sck_10_pins>, <&i2c_ao_sda_11_pins>;
+ pinctrl-names = "default";
+};
+
+&pwm_ab {
+ status = "okay";
+ pinctrl-0 = <&pwm_a_x20_pins>;
+ pinctrl-names = "default";
+};
+
+/* wifi module */
+&sd_emmc_b {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ sd-uhs-sdr104;
+ max-frequency = <200000000>;
+ non-removable;
+ disable-wp;
+
+ mmc-pwrseq = <&sdio_pwrseq>;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+/* emmc storage */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ max-frequency = <200000000>;
+ non-removable;
+ disable-wp;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
+
+/* UART Bluetooth */
+&uart_B {
+ status = "okay";
+ pinctrl-0 = <&uart_b_z_pins>, <&uart_b_z_cts_rts_pins>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ shutdown-gpios = <&gpio GPIOZ_7 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+/* UART Console */
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+/* UART Wireless module */
+&uart_AO_B {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_b_pins>;
+ pinctrl-names = "default";
+};
+
+&usb {
+ status = "okay";
+ phy-supply = <&usb_pwr>;
+};
+
+&spicc1 {
+ status = "okay";
+ pinctrl-0 = <&spi1_x_pins>, <&spi1_ss0_x_pins>;
+ pinctrl-names = "default";
+};
+
+&gpio {
+ gpio-line-names =
+ "", "", "", "", "", // 0 - 4
+ "", "", "", "", "", // 5 - 9
+ "UserButton", "", "", "", "", // 10 - 14
+ "", "", "", "", "", // 15 - 19
+ "", "", "", "", "", // 20 - 24
+ "", "LedRed", "LedGreen", "Output3", "Output2", // 25 - 29
+ "Output1", "", "", "", "", // 30 - 34
+ "", "ZigBeeBOOT", "", "", "", // 35 - 39
+ "1Wire", "ZigBeeRESET", "", "Input4", "Input3", // 40 - 44
+ "Input2", "Input1", "", "", "", // 45 - 49
+ "", "", "", "", "", // 50 - 54
+ "", "", "", "", "", // 55 - 59
+ "", "", "", "", "", // 60 - 64
+ "", "", "", "", "", // 65 - 69
+ "", "", "", "", "", // 70 - 74
+ "", "", "", "", "", // 75 - 79
+ "", "", "", "", "", // 80 - 84
+ "", ""; // 85-86
+};
+
+&cpu0 {
+ #cooling-cells = <2>;
+};
+
+&cpu1 {
+ #cooling-cells = <2>;
+};
+
+&cpu2 {
+ #cooling-cells = <2>;
+};
+
+&cpu3 {
+ #cooling-cells = <2>;
+};
--
2.30.2
On Wed, 15 Sep 2021 11:57:15 +0300, Vyacheslav Bocharov wrote:
> JetHome is trademark of IP Sokolov P.A., manufacturer of home automation
> devices.
>
> Signed-off-by: Vyacheslav Bocharov <[email protected]>
> ---
> Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
> 1 file changed, 2 insertions(+)
>
Acked-by: Rob Herring <[email protected]>
Hi,
On Wed, 15 Sep 2021 11:57:11 +0300, Vyacheslav Bocharov wrote:
> Add support for new home automation devices.
>
> JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features:
> - DIN Rail Mounting
> - Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
> - no video out
> - 512Mb/1GB LPDDR4
> - 8/16GB eMMC flash
> - 1 x USB 2.0
> - 1 x 10/100Mbps ethernet
> - WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2.
> - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
> - 2 x gpio LEDS
> - GPIO user Button
> - 1 x 1-Wire
> - 2 x RS-485
> - 4 x dry contact digital GPIO inputs
> - 3 x relay GPIO outputs
> - DC source with a voltage of 9 to 56 V / Passive POE
>
> [...]
Thanks, Applied to https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux.git (v5.16/dt64)
[1/4] dt-bindings: arm: amlogic: add bindings for Jethub D1/H1
https://git.kernel.org/amlogic/c/c649e25c0fcd53e0f1e83f710fefbda9d2809c32
[2/4] dt-bindings: vendor-prefixes: add jethome prefix
https://git.kernel.org/amlogic/c/a1732cca0ed3d1ac2a256d16302c93443d636146
[3/4] arm64: dts: meson-gxl: add support for JetHub H1
https://git.kernel.org/amlogic/c/abfaae24ecf3e7f00508b60fa05e2b6789b8f607
[4/4] arm64: dts: meson-axg: add support for JetHub D1
https://git.kernel.org/amlogic/c/8e279fb2903990cc6296ec56b3b80b2f854b6c79
--
Neil
On 15/09/2021 10:57, Vyacheslav Bocharov wrote:
> JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation
> controller with the following features:
> - DIN Rail Mounting
> - Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
> - no video out
> - 512Mb/1GB LPDDR4
> - 8/16GB eMMC flash
> - 1 x USB 2.0
> - 1 x 10/100Mbps ethernet
> - WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac,
> Bluetooth 4.2.
> - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power
> and Zigbee 3.0 support.
> - 2 x gpio LEDS
> - GPIO user Button
> - 1 x 1-Wire
> - 2 x RS-485
> - 4 x dry contact digital GPIO inputs
> - 3 x relay GPIO outputs
> - DC source with a voltage of 9 to 56 V / Passive POE
>
> Changes from v4:
> - add node for 1wire-gpio for JetHub D1 v2 device
>
> Signed-off-by: Vyacheslav Bocharov <[email protected]>
>
>
> ---
> arch/arm64/boot/dts/amlogic/Makefile | 1 +
> .../amlogic/meson-axg-jethome-jethub-j100.dts | 361 ++++++++++++++++++
> 2 files changed, 362 insertions(+)
> create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
>
> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
> index 2c3ce7c401a5..3ba6f58b9833 100644
> --- a/arch/arm64/boot/dts/amlogic/Makefile
> +++ b/arch/arm64/boot/dts/amlogic/Makefile
> @@ -1,5 +1,6 @@
> # SPDX-License-Identifier: GPL-2.0
> dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
> +dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j100.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
> diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
> new file mode 100644
> index 000000000000..c25b03a91e12
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
> @@ -0,0 +1,361 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2021 Vyacheslav Bocharov <[email protected]>
> + * Copyright (c) 2020 JetHome
> + * Author: Aleksandr Kazantsev <[email protected]>
> + * Author: Alexey Shevelkin <[email protected]>
> + * Author: Vyacheslav Bocharov <[email protected]>
> + */
> +
> +/dts-v1/;
> +
> +#include "meson-axg.dtsi"
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/thermal/thermal.h>
> +
> +/ {
> + compatible = "jethome,jethub-j100", "amlogic,a113d", "amlogic,meson-axg";
> + model = "JetHome JetHub J100";
> + aliases {
> + serial0 = &uart_AO; /* Console */
> + serial1 = &uart_AO_B; /* External UART (Wireless Module) */
> + ethernet0 = ðmac;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + /* 1024MB RAM */
> + memory@0 {
> + device_type = "memory";
> + reg = <0x0 0x0 0x0 0x40000000>;
> + };
> +
> + reserved-memory {
> + linux,cma {
> + size = <0x0 0x400000>;
> + };
> + };
> +
> + emmc_pwrseq: emmc-pwrseq {
> + compatible = "mmc-pwrseq-emmc";
> + reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
> + };
> +
> + vcc_3v3: regulator-vcc_3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vddao_3v3>;
> + regulator-always-on;
> + };
> +
> + vcc_5v: regulator-vcc_5v {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC5V";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + };
> +
> + vddao_3v3: regulator-vddao_3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDAO_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc_5v>;
> + regulator-always-on;
> + };
> +
> + vddio_ao18: regulator-vddio_ao18 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDIO_AO18";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vddao_3v3>;
> + regulator-always-on;
> + };
> +
> + vddio_boot: regulator-vddio_boot {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDIO_BOOT";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vddao_3v3>;
> + regulator-always-on;
> + };
> +
> + usb_pwr: regulator-usb_pwr {
> + compatible = "regulator-fixed";
> + regulator-name = "USB_PWR";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc_5v>;
> + regulator-always-on;
> + };
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + reset-gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
> + clocks = <&wifi32k>;
> + clock-names = "ext_clock";
> + };
> +
> + wifi32k: wifi32k {
> + compatible = "pwm-clock";
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + pwms = <&pwm_ab 0 30518 0>; /* PWM_A at 32.768KHz */
> + };
> +
> + thermal-zones {
> + cpu_thermal: cpu-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> + thermal-sensors = <&scpi_sensors 0>;
> + trips {
> + cpu_passive: cpu-passive {
> + temperature = <70000>; /* millicelsius */
> + hysteresis = <2000>; /* millicelsius */
> + type = "passive";
> + };
> +
> + cpu_hot: cpu-hot {
> + temperature = <80000>; /* millicelsius */
> + hysteresis = <2000>; /* millicelsius */
> + type = "hot";
> + };
> +
> + cpu_critical: cpu-critical {
> + temperature = <100000>; /* millicelsius */
> + hysteresis = <2000>; /* millicelsius */
> + type = "critical";
> + };
> + };
> + };
> +
> + cpu_cooling_maps: cooling-maps {
> + map0 {
> + trip = <&cpu_passive>;
> + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> +
> + map1 {
> + trip = <&cpu_hot>;
> + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> + };
> + };
Newline is missing here, I'll add while applying.
> + onewire {
> + compatible = "w1-gpio";
> + gpios = <&gpio GPIOA_14 GPIO_ACTIVE_HIGH>;
> + #gpio-cells = <1>;
> + };
> +};
> +
> +&efuse {
> + sn: sn@32 {
> + reg = <0x32 0x20>;
> + };
> +
> + eth_mac: eth_mac@0 {
> + reg = <0x0 0x6>;
> + };
> +
> + bt_mac: bt_mac@6 {
> + reg = <0x6 0x6>;
> + };
> +
> + wifi_mac: wifi_mac@c {
> + reg = <0xc 0x6>;
> + };
> +
> + bid: bid@12 {
> + reg = <0x12 0x20>;
> + };
> +};
> +
> +ðmac {
> + status = "okay";
> + pinctrl-0 = <ð_rmii_x_pins>;
> + pinctrl-names = "default";
> + phy-handle = <ð_phy0>;
> + phy-mode = "rmii";
> +
> + mdio {
> + compatible = "snps,dwmac-mdio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* ICPlus IP101A/G Ethernet PHY (vendor_id=0x0243, model_id=0x0c54) */
> + eth_phy0: ethernet-phy@0 {
> + /* compatible = "ethernet-phy-id0243.0c54";*/
> + max-speed = <100>;
> + reg = <0>;
> +
> + reset-assert-us = <10000>;
> + reset-deassert-us = <10000>;
> + reset-gpios = <&gpio GPIOZ_5 GPIO_ACTIVE_LOW>;
> + };
> + };
> +};
> +
> +/* Internal I2C bus (on CPU module) */
> +&i2c1 {
> + status = "okay";
> + pinctrl-0 = <&i2c1_z_pins>;
> + pinctrl-names = "default";
> +
> + /* RTC */
> + pcf8563: pcf8563@51 {
> + compatible = "nxp,pcf8563";
> + reg = <0x51>;
> + status = "okay";
> + };
> +};
> +
> +/* Peripheral I2C bus (on motherboard) */
> +&i2c_AO {
> + status = "okay";
> + pinctrl-0 = <&i2c_ao_sck_10_pins>, <&i2c_ao_sda_11_pins>;
> + pinctrl-names = "default";
> +};
> +
> +&pwm_ab {
> + status = "okay";
> + pinctrl-0 = <&pwm_a_x20_pins>;
> + pinctrl-names = "default";
> +};
> +
> +/* wifi module */
> +&sd_emmc_b {
> + status = "okay";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pinctrl-0 = <&sdio_pins>;
> + pinctrl-1 = <&sdio_clk_gate_pins>;
> + pinctrl-names = "default", "clk-gate";
> +
> + bus-width = <4>;
> + cap-sd-highspeed;
> + sd-uhs-sdr104;
> + max-frequency = <200000000>;
> + non-removable;
> + disable-wp;
> +
> + mmc-pwrseq = <&sdio_pwrseq>;
> +
> + vmmc-supply = <&vddao_3v3>;
> + vqmmc-supply = <&vddio_boot>;
> +
> + brcmf: wifi@1 {
> + reg = <1>;
> + compatible = "brcm,bcm4329-fmac";
> + };
> +};
> +
> +/* emmc storage */
> +&sd_emmc_c {
> + status = "okay";
> + pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
> + pinctrl-1 = <&emmc_clk_gate_pins>;
> + pinctrl-names = "default", "clk-gate";
> +
> + bus-width = <8>;
> + cap-mmc-highspeed;
> + max-frequency = <200000000>;
> + non-removable;
> + disable-wp;
> + mmc-ddr-1_8v;
> + mmc-hs200-1_8v;
> +
> + mmc-pwrseq = <&emmc_pwrseq>;
> +
> + vmmc-supply = <&vcc_3v3>;
> + vqmmc-supply = <&vddio_boot>;
> +};
> +
> +/* UART Bluetooth */
> +&uart_B {
> + status = "okay";
> + pinctrl-0 = <&uart_b_z_pins>, <&uart_b_z_cts_rts_pins>;
> + pinctrl-names = "default";
> + uart-has-rtscts;
> +
> + bluetooth {
> + compatible = "brcm,bcm43438-bt";
> + shutdown-gpios = <&gpio GPIOZ_7 GPIO_ACTIVE_HIGH>;
> + };
> +};
> +
> +/* UART Console */
> +&uart_AO {
> + status = "okay";
> + pinctrl-0 = <&uart_ao_a_pins>;
> + pinctrl-names = "default";
> +};
> +
> +/* UART Wireless module */
> +&uart_AO_B {
> + status = "okay";
> + pinctrl-0 = <&uart_ao_b_pins>;
> + pinctrl-names = "default";
> +};
> +
> +&usb {
> + status = "okay";
> + phy-supply = <&usb_pwr>;
> +};
> +
> +&spicc1 {
> + status = "okay";
> + pinctrl-0 = <&spi1_x_pins>, <&spi1_ss0_x_pins>;
> + pinctrl-names = "default";
> +};
> +
> +&gpio {
> + gpio-line-names =
> + "", "", "", "", "", // 0 - 4
> + "", "", "", "", "", // 5 - 9
> + "UserButton", "", "", "", "", // 10 - 14
> + "", "", "", "", "", // 15 - 19
> + "", "", "", "", "", // 20 - 24
> + "", "LedRed", "LedGreen", "Output3", "Output2", // 25 - 29
> + "Output1", "", "", "", "", // 30 - 34
> + "", "ZigBeeBOOT", "", "", "", // 35 - 39
> + "1Wire", "ZigBeeRESET", "", "Input4", "Input3", // 40 - 44
> + "Input2", "Input1", "", "", "", // 45 - 49
> + "", "", "", "", "", // 50 - 54
> + "", "", "", "", "", // 55 - 59
> + "", "", "", "", "", // 60 - 64
> + "", "", "", "", "", // 65 - 69
> + "", "", "", "", "", // 70 - 74
> + "", "", "", "", "", // 75 - 79
> + "", "", "", "", "", // 80 - 84
> + "", ""; // 85-86
> +};
> +
> +&cpu0 {
> + #cooling-cells = <2>;
> +};
> +
> +&cpu1 {
> + #cooling-cells = <2>;
> +};
> +
> +&cpu2 {
> + #cooling-cells = <2>;
> +};
> +
> +&cpu3 {
> + #cooling-cells = <2>;
> +};
>
Reviewed-by: Neil Armstrong <[email protected]>
Thanks,
Neil
17.09.2021 10:27, Neil Armstrong wrote:
> Hi,
>
> Thanks, Applied to https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux.git (v5.16/dt64)
Thanks