Due to changes in the hardware design of the handshaking signal
between i2c and dma, it is necessary to reset the handshaking
signal before each transfer to ensure that the multi-msgs can
be transferred correctly.
Signed-off-by: Kewei Xu <[email protected]>
Reviewed-by: Qii Wang <[email protected]>
---
drivers/i2c/busses/i2c-mt65xx.c | 26 ++++++++++++++++++++++++++
1 file changed, 26 insertions(+)
diff --git a/drivers/i2c/busses/i2c-mt65xx.c b/drivers/i2c/busses/i2c-mt65xx.c
index 72acda59eb39..dad3a85cd499 100644
--- a/drivers/i2c/busses/i2c-mt65xx.c
+++ b/drivers/i2c/busses/i2c-mt65xx.c
@@ -15,6 +15,7 @@
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/io.h>
+#include <linux/iopoll.h>
#include <linux/kernel.h>
#include <linux/mm.h>
#include <linux/module.h>
@@ -49,6 +50,8 @@
#define I2C_RD_TRANAC_VALUE 0x0001
#define I2C_SCL_MIS_COMP_VALUE 0x0000
#define I2C_CHN_CLR_FLAG 0x0000
+#define I2C_RELIABILITY 0x0010
+#define I2C_DMAACK_ENABLE 0x0008
#define I2C_DMA_CON_TX 0x0000
#define I2C_DMA_CON_RX 0x0001
@@ -851,6 +854,7 @@ static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs,
u16 restart_flag = 0;
u16 dma_sync = 0;
u32 reg_4g_mode;
+ u32 reg_dma_reset;
u8 *dma_rd_buf = NULL;
u8 *dma_wr_buf = NULL;
dma_addr_t rpaddr = 0;
@@ -864,6 +868,28 @@ static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs,
reinit_completion(&i2c->msg_complete);
+ if (i2c->dev_comp->apdma_sync &&
+ i2c->op != I2C_MASTER_WRRD && num > 1) {
+ mtk_i2c_writew(i2c, 0x00, OFFSET_DEBUGCTRL);
+ writel(I2C_DMA_HANDSHAKE_RST | I2C_DMA_WARM_RST,
+ i2c->pdmabase + OFFSET_RST);
+
+ ret = readw_poll_timeout(i2c->pdmabase + OFFSET_RST,
+ reg_dma_reset,
+ !(reg_dma_reset & I2C_DMA_WARM_RST),
+ 0, 100);
+ if (ret) {
+ dev_err(i2c->dev, "DMA warm reset timeout\n");
+ return -ETIMEDOUT;
+ }
+
+ writel(I2C_DMA_CLR_FLAG, i2c->pdmabase + OFFSET_RST);
+ mtk_i2c_writew(i2c, I2C_HANDSHAKE_RST, OFFSET_SOFTRESET);
+ mtk_i2c_writew(i2c, I2C_CHN_CLR_FLAG, OFFSET_SOFTRESET);
+ mtk_i2c_writew(i2c, I2C_RELIABILITY | I2C_DMAACK_ENABLE,
+ OFFSET_DEBUGCTRL);
+ }
+
control_reg = mtk_i2c_readw(i2c, OFFSET_CONTROL) &
~(I2C_CONTROL_DIR_CHANGE | I2C_CONTROL_RS);
if ((i2c->speed_hz > I2C_MAX_FAST_MODE_PLUS_FREQ) || (left_num >= 1))
--
2.25.1
On Sun, Oct 10, 2021 at 03:05:12PM +0800, Kewei Xu wrote:
> Due to changes in the hardware design of the handshaking signal
> between i2c and dma, it is necessary to reset the handshaking
> signal before each transfer to ensure that the multi-msgs can
> be transferred correctly.
>
> Signed-off-by: Kewei Xu <[email protected]>
> Reviewed-by: Qii Wang <[email protected]>
Applied to for-next, thanks!