This watchdog timer is found on Realtek's Otto MIPS platforms, including the
RTL838x, RTL839x, and RTL930x series of ethernet switch SoCs. It has a number
of reset modes (SoC, CPU, software), and can provide pretimeout interrupts.
The timer has two timeout phases. Both phases have a maximum duration of 32
prescaled clock ticks, which is ca. 43s with a clock of 200MHz:
- Phase 1: During this phase, the WDT can be pinged to reset the timeout.
- Phase 2: Starts after phase 1 has timed out, and only serves to give the
system some time to clean up, or notify others that it's going to reset.
During this phase, pinging the WDT has no effect, and a reset is unavoidable.
The driver has been tested on a Zyxel GS1900-8 (RTL8380, mainline kernel and
OpenWrt), a Zyxel GS1900-48 (RTL8393, mainline), a Netgear GS110TPPv1
(RTL8381, mainline), and a Zyxel XGS1250-12 (RTL9203B, Openwrt).
Main changes since v1:
Link: https://lore.kernel.org/all/[email protected]/
- Drop implementation of phase2 irq, since it is only triggered on system reset
- Drop redundant value checks and lock
- Add RTL930x compatibility
Sander Vanheule (2):
dt-bindings: watchdog: Realtek Otto WDT binding
watchdog: Add Realtek Otto watchdog timer
.../bindings/watchdog/realtek,otto-wdt.yaml | 91 +++++
MAINTAINERS | 7 +
drivers/watchdog/Kconfig | 13 +
drivers/watchdog/Makefile | 1 +
drivers/watchdog/realtek_otto_wdt.c | 359 ++++++++++++++++++
5 files changed, 471 insertions(+)
create mode 100644 Documentation/devicetree/bindings/watchdog/realtek,otto-wdt.yaml
create mode 100644 drivers/watchdog/realtek_otto_wdt.c
--
2.31.1
Realtek MIPS SoCs (platform name Otto) have a watchdog timer with
pretimeout notifitication support. The WDT can (partially) hard reset,
or soft reset the SoC.
This driver implements all features as described in the devicetree
binding, except the phase2 interrupt, and also functions as a restart
handler. The cpu reset mode is considered to be a "warm" restart, since
this mode does not reset all peripherals. Being an embedded system
though, the "cpu" and "software" modes will still cause the bootloader
to run on restart.
It is not known how a forced system reset can be disabled on the
supported platforms. This means that the phase2 interrupt will only fire
at the same time as reset, so implementing phase2 is of little use.
Signed-off-by: Sander Vanheule <[email protected]>
--
v2 -> v1:
- drop raw_spinlock, locking is not required
- replace devm_free_irq with disable_irq
- use max_hw_heartbeat_ms instead of max_timeout
- drop redundant timeout value checks
- replace ROUND_CLOSEST by ROUND_UP for tick counts, and flooring
division for timeout values
- change COMMON_CLK 'select' into 'depends on'
- add MODULE_DEVICE_TABLE for OF ID table
- add realtek,rtl9300 compatible
- drop phase2 irq
---
MAINTAINERS | 7 +
drivers/watchdog/Kconfig | 13 +
drivers/watchdog/Makefile | 1 +
drivers/watchdog/realtek_otto_wdt.c | 359 ++++++++++++++++++++++++++++
4 files changed, 380 insertions(+)
create mode 100644 drivers/watchdog/realtek_otto_wdt.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 2c9070aeba2a..54c8f788d3e5 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -15991,6 +15991,13 @@ S: Maintained
F: include/sound/rt*.h
F: sound/soc/codecs/rt*
+REALTEK OTTO WATCHDOG
+M: Sander Vanheule <[email protected]>
+L: [email protected]
+S: Maintained
+F: Documentation/devicetree/bindings/watchdog/realtek,otto-wdt.yaml
+F: driver/watchdog/realtek_otto_wdt.c
+
REALTEK RTL83xx SMI DSA ROUTER CHIPS
M: Linus Walleij <[email protected]>
S: Maintained
diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
index bf59faeb3de1..d308e13a9aa1 100644
--- a/drivers/watchdog/Kconfig
+++ b/drivers/watchdog/Kconfig
@@ -954,6 +954,19 @@ config RTD119X_WATCHDOG
Say Y here to include support for the watchdog timer in
Realtek RTD1295 SoCs.
+config REALTEK_OTTO_WDT
+ tristate "Realtek Otto MIPS watchdog support"
+ depends on MACH_REALTEK_RTL || COMPILE_TEST
+ depends on COMMON_CLK
+ select WATCHDOG_CORE
+ default MACH_REALTEK_RTL
+ help
+ Say Y here to include support for the watchdog timer on Realtek
+ RTL838x, RTL839x, RTL930x SoCs. This watchdog has pretimeout
+ notifications and system reset on timeout.
+
+ When built as a module this will be called realtek_otto_wdt.
+
config SPRD_WATCHDOG
tristate "Spreadtrum watchdog support"
depends on ARCH_SPRD || COMPILE_TEST
diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
index 1bd2d6f37c53..a8dccf819163 100644
--- a/drivers/watchdog/Makefile
+++ b/drivers/watchdog/Makefile
@@ -171,6 +171,7 @@ obj-$(CONFIG_IMGPDC_WDT) += imgpdc_wdt.o
obj-$(CONFIG_MT7621_WDT) += mt7621_wdt.o
obj-$(CONFIG_PIC32_WDT) += pic32-wdt.o
obj-$(CONFIG_PIC32_DMT) += pic32-dmt.o
+obj-$(CONFIG_REALTEK_OTTO_WDT) += realtek_otto_wdt.o
# PARISC Architecture
diff --git a/drivers/watchdog/realtek_otto_wdt.c b/drivers/watchdog/realtek_otto_wdt.c
new file mode 100644
index 000000000000..ba12e0181081
--- /dev/null
+++ b/drivers/watchdog/realtek_otto_wdt.c
@@ -0,0 +1,359 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/*
+ * Realtek Otto MIPS platform watchdog
+ *
+ * Watchdog timer that will reset the system after timeout, using the selected
+ * reset mode.
+ *
+ * Counter scaling and timeouts:
+ * - Base prescale of (2 << 25), providing tick duration T_0: 168ms @ 200MHz
+ * - PRESCALE: logarithmic prescaler adding a factor of {1, 2, 4, 8}
+ * - Phase 1: Times out after (PHASE1 + 1) × PRESCALE × T_0
+ * Generates an interrupt, WDT cannot be stopped after phase 1
+ * - Phase 2: starts after phase 1, times out after (PHASE2 + 1) × PRESCALE × T_0
+ * Resets the system according to RST_MODE
+ */
+
+#include <linux/bits.h>
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/math.h>
+#include <linux/minmax.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+#include <linux/reboot.h>
+#include <linux/watchdog.h>
+
+#define OTTO_WDT_REG_CNTR 0x0
+#define OTTO_WDT_CNTR_PING BIT(31)
+
+#define OTTO_WDT_REG_INTR 0x4
+#define OTTO_WDT_INTR_PHASE_1 BIT(31)
+#define OTTO_WDT_INTR_PHASE_2 BIT(30)
+
+#define OTTO_WDT_REG_CTRL 0x8
+#define OTTO_WDT_CTRL_ENABLE BIT(31)
+#define OTTO_WDT_CTRL_PRESCALE GENMASK(30, 29)
+#define OTTO_WDT_CTRL_PHASE1 GENMASK(26, 22)
+#define OTTO_WDT_CTRL_PHASE2 GENMASK(19, 15)
+#define OTTO_WDT_CTRL_RST_MODE GENMASK(1, 0)
+#define OTTO_WDT_MODE_SOC 0
+#define OTTO_WDT_MODE_CPU 1
+#define OTTO_WDT_MODE_SOFTWARE 2
+#define OTTO_WDT_CTRL_DEFAULT OTTO_WDT_MODE_CPU
+
+#define OTTO_WDT_PRESCALE_MAX 3
+
+/*
+ * One higher than the max values contained in PHASE{1,2}, since a value of 0
+ * corresponds to one tick.
+ */
+#define OTTO_WDT_PHASE_TICKS_MAX 32
+
+/*
+ * The maximum reset delay is actually 2×32 ticks, but that would require large
+ * pretimeout values for timeouts longer than 32 ticks. Limit the maximum timeout
+ * to 32 + 1 to ensure small pretimeout values can be configured as expected.
+ */
+#define OTTO_WDT_TIMEOUT_TICKS_MAX (OTTO_WDT_PHASE_TICKS_MAX + 1)
+
+struct otto_wdt_ctrl {
+ struct watchdog_device wdev;
+ struct device *dev;
+ void __iomem *base;
+ struct clk *clk;
+ int irq_phase1;
+};
+
+static int otto_wdt_start(struct watchdog_device *wdev)
+{
+ struct otto_wdt_ctrl *ctrl = watchdog_get_drvdata(wdev);
+ u32 v;
+
+ v = ioread32(ctrl->base + OTTO_WDT_REG_CTRL);
+ v |= OTTO_WDT_CTRL_ENABLE;
+ iowrite32(v, ctrl->base + OTTO_WDT_REG_CTRL);
+
+ return 0;
+}
+
+static int otto_wdt_stop(struct watchdog_device *wdev)
+{
+ struct otto_wdt_ctrl *ctrl = watchdog_get_drvdata(wdev);
+ u32 v;
+
+ v = ioread32(ctrl->base + OTTO_WDT_REG_CTRL);
+ v &= ~OTTO_WDT_CTRL_ENABLE;
+ iowrite32(v, ctrl->base + OTTO_WDT_REG_CTRL);
+
+ return 0;
+}
+
+static int otto_wdt_ping(struct watchdog_device *wdev)
+{
+ struct otto_wdt_ctrl *ctrl = watchdog_get_drvdata(wdev);
+
+ iowrite32(OTTO_WDT_CNTR_PING, ctrl->base + OTTO_WDT_REG_CNTR);
+
+ return 0;
+}
+
+static int otto_wdt_tick_ms(struct otto_wdt_ctrl *ctrl, int prescale)
+{
+ unsigned int rate_khz = clk_get_rate(ctrl->clk) / 1000;
+
+ if (!rate_khz)
+ return 0;
+
+ return DIV_ROUND_CLOSEST(1 << (25 + prescale), rate_khz);
+}
+
+/*
+ * The timer asserts the PHASE1/PHASE2 IRQs when the number of ticks exceeds
+ * the value stored in those fields. This means each phase will run for at least
+ * one tick, so small values need to be clamped to correctly reflect the timeout.
+ */
+static inline unsigned int div_round_ticks(unsigned int val, unsigned int tick_duration,
+ unsigned int min_ticks)
+{
+ return max(min_ticks, DIV_ROUND_UP(val, tick_duration));
+}
+
+static int otto_wdt_determine_timeouts(struct watchdog_device *wdev, unsigned int timeout,
+ unsigned int pretimeout)
+{
+ struct otto_wdt_ctrl *ctrl = watchdog_get_drvdata(wdev);
+ unsigned int pretimeout_ms = pretimeout * 1000;
+ unsigned int timeout_ms = timeout * 1000;
+ unsigned int prescale = 0;
+ unsigned int phase1_ticks;
+ unsigned int phase2_ticks;
+ unsigned int total_ticks;
+ unsigned int tick_ms;
+ u32 v;
+
+ do {
+ if (prescale > OTTO_WDT_PRESCALE_MAX)
+ return -EINVAL;
+
+ tick_ms = otto_wdt_tick_ms(ctrl, prescale);
+ total_ticks = div_round_ticks(timeout_ms, tick_ms, 2);
+ phase1_ticks = div_round_ticks(timeout_ms - pretimeout_ms, tick_ms, 1);
+ phase2_ticks = total_ticks - phase1_ticks;
+
+ prescale++;
+ } while (phase1_ticks > OTTO_WDT_PHASE_TICKS_MAX
+ || phase2_ticks > OTTO_WDT_PHASE_TICKS_MAX);
+
+ v = ioread32(ctrl->base + OTTO_WDT_REG_CTRL);
+
+ v &= ~(OTTO_WDT_CTRL_PRESCALE | OTTO_WDT_CTRL_PHASE1 | OTTO_WDT_CTRL_PHASE2);
+ v |= FIELD_PREP(OTTO_WDT_CTRL_PHASE1, phase1_ticks - 1);
+ v |= FIELD_PREP(OTTO_WDT_CTRL_PHASE2, phase2_ticks - 1);
+ v |= FIELD_PREP(OTTO_WDT_CTRL_PRESCALE, prescale);
+
+ iowrite32(v, ctrl->base + OTTO_WDT_REG_CTRL);
+
+ timeout_ms = total_ticks * tick_ms;
+ ctrl->wdev.timeout = timeout_ms / 1000;
+
+ pretimeout_ms = phase2_ticks * tick_ms;
+ ctrl->wdev.pretimeout = pretimeout_ms / 1000;
+
+ return 0;
+}
+
+static int otto_wdt_set_timeout(struct watchdog_device *wdev, unsigned int val)
+{
+ return otto_wdt_determine_timeouts(wdev, val, min(wdev->pretimeout, val - 1));
+}
+
+static int otto_wdt_set_pretimeout(struct watchdog_device *wdev, unsigned int val)
+{
+ return otto_wdt_determine_timeouts(wdev, wdev->timeout, val);
+}
+
+static int otto_wdt_restart(struct watchdog_device *wdev, unsigned long reboot_mode,
+ void *data)
+{
+ struct otto_wdt_ctrl *ctrl = watchdog_get_drvdata(wdev);
+ u32 reset_mode;
+ u32 v;
+
+ disable_irq(ctrl->irq_phase1);
+
+ switch (reboot_mode) {
+ case REBOOT_SOFT:
+ reset_mode = OTTO_WDT_MODE_SOFTWARE;
+ break;
+ case REBOOT_WARM:
+ reset_mode = OTTO_WDT_MODE_CPU;
+ break;
+ default:
+ reset_mode = OTTO_WDT_MODE_SOC;
+ break;
+ }
+
+ /* Configure for shortest timeout and wait for reset to occur */
+ v = FIELD_PREP(OTTO_WDT_CTRL_RST_MODE, reset_mode) | OTTO_WDT_CTRL_ENABLE;
+ iowrite32(v, ctrl->base + OTTO_WDT_REG_CTRL);
+
+ mdelay(3 * otto_wdt_tick_ms(ctrl, 0));
+
+ return 0;
+}
+
+static irqreturn_t otto_wdt_phase1_isr(int irq, void *dev_id)
+{
+ struct otto_wdt_ctrl *ctrl = dev_id;
+
+ iowrite32(OTTO_WDT_INTR_PHASE_1, ctrl->base + OTTO_WDT_REG_INTR);
+ dev_crit(ctrl->dev, "phase 1 timeout\n");
+ watchdog_notify_pretimeout(&ctrl->wdev);
+
+ return IRQ_HANDLED;
+}
+
+static const struct watchdog_ops otto_wdt_ops = {
+ .owner = THIS_MODULE,
+ .start = otto_wdt_start,
+ .stop = otto_wdt_stop,
+ .ping = otto_wdt_ping,
+ .set_timeout = otto_wdt_set_timeout,
+ .set_pretimeout = otto_wdt_set_pretimeout,
+ .restart = otto_wdt_restart,
+};
+
+static const struct watchdog_info otto_wdt_info = {
+ .identity = "Realtek Otto watchdog timer",
+ .options = WDIOF_KEEPALIVEPING |
+ WDIOF_MAGICCLOSE |
+ WDIOF_SETTIMEOUT |
+ WDIOF_PRETIMEOUT,
+};
+
+static int otto_wdt_probe_reset_mode(struct otto_wdt_ctrl *ctrl)
+{
+ static const char *mode_property = "realtek,reset-mode";
+ const struct fwnode_handle *node = ctrl->dev->fwnode;
+ int mode_count;
+ u32 mode;
+ u32 v;
+
+ if (!node)
+ return -ENXIO;
+
+ mode_count = fwnode_property_string_array_count(node, mode_property);
+ if (mode_count < 0)
+ return mode_count;
+ else if (mode_count == 0)
+ return 0;
+ else if (mode_count != 1)
+ return -EINVAL;
+
+ if (fwnode_property_match_string(node, mode_property, "soc") == 0)
+ mode = OTTO_WDT_MODE_SOC;
+ else if (fwnode_property_match_string(node, mode_property, "cpu") == 0)
+ mode = OTTO_WDT_MODE_CPU;
+ else if (fwnode_property_match_string(node, mode_property, "software") == 0)
+ mode = OTTO_WDT_MODE_SOFTWARE;
+ else
+ return -EINVAL;
+
+ v = ioread32(ctrl->base + OTTO_WDT_REG_CTRL);
+ v &= ~OTTO_WDT_CTRL_RST_MODE;
+ v |= FIELD_PREP(OTTO_WDT_CTRL_RST_MODE, mode);
+ iowrite32(v, ctrl->base + OTTO_WDT_REG_CTRL);
+
+ return 0;
+}
+
+static int otto_wdt_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct otto_wdt_ctrl *ctrl;
+ unsigned int max_tick_ms;
+ int ret;
+
+ ctrl = devm_kzalloc(dev, sizeof(*ctrl), GFP_KERNEL);
+ if (!ctrl)
+ return -ENOMEM;
+
+ ctrl->dev = dev;
+ ctrl->base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(ctrl->base))
+ return PTR_ERR(ctrl->base);
+
+ /* Clear any old interrupts and reset initial state */
+ iowrite32(OTTO_WDT_INTR_PHASE_1 | OTTO_WDT_INTR_PHASE_2,
+ ctrl->base + OTTO_WDT_REG_INTR);
+ iowrite32(OTTO_WDT_CTRL_DEFAULT, ctrl->base + OTTO_WDT_REG_CTRL);
+
+ ctrl->clk = devm_clk_get(dev, NULL);
+ if (IS_ERR(ctrl->clk))
+ return dev_err_probe(dev, PTR_ERR(ctrl->clk), "Failed to get clock\n");
+
+ ctrl->irq_phase1 = platform_get_irq_byname(pdev, "phase1");
+ if (ctrl->irq_phase1 < 0)
+ return dev_err_probe(dev, ctrl->irq_phase1, "phase1 IRQ not found\n");
+
+ ret = devm_request_irq(dev, ctrl->irq_phase1, otto_wdt_phase1_isr, 0,
+ "realtek-otto-wdt", ctrl);
+ if (ret)
+ return dev_err_probe(dev, ret, "Failed to get IRQ for phase1\n");
+
+ ret = otto_wdt_probe_reset_mode(ctrl);
+ if (ret)
+ return dev_err_probe(dev, ret, "Invalid reset mode specified\n");
+
+ ctrl->wdev.parent = dev;
+ ctrl->wdev.info = &otto_wdt_info;
+ ctrl->wdev.ops = &otto_wdt_ops;
+
+ /*
+ * Since pretimeout cannot be disabled, min. timeout is twice the
+ * subsystem resolution. max. timeout is ca. 43s at a bus clock of 200MHz.
+ */
+ ctrl->wdev.min_timeout = 2;
+ max_tick_ms = otto_wdt_tick_ms(ctrl, OTTO_WDT_PRESCALE_MAX);
+ ctrl->wdev.max_hw_heartbeat_ms = max_tick_ms * OTTO_WDT_TIMEOUT_TICKS_MAX;
+ ctrl->wdev.timeout = min(30U, ctrl->wdev.max_hw_heartbeat_ms / 1000);
+
+ watchdog_set_drvdata(&ctrl->wdev, ctrl);
+ watchdog_init_timeout(&ctrl->wdev, 0, dev);
+ watchdog_stop_on_reboot(&ctrl->wdev);
+ watchdog_set_restart_priority(&ctrl->wdev, 128);
+
+ ret = otto_wdt_determine_timeouts(&ctrl->wdev, ctrl->wdev.timeout, 1);
+ if (ret)
+ return dev_err_probe(dev, ret, "Failed to set timeout\n");
+
+ return devm_watchdog_register_device(dev, &ctrl->wdev);
+}
+
+static const struct of_device_id otto_wdt_ids[] = {
+ { .compatible = "realtek,rtl8380-wdt" },
+ { .compatible = "realtek,rtl8390-wdt" },
+ { .compatible = "realtek,rtl9300-wdt" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, otto_wdt_ids);
+
+static struct platform_driver otto_wdt_driver = {
+ .probe = otto_wdt_probe,
+ .driver = {
+ .name = "realtek-otto-watchdog",
+ .of_match_table = otto_wdt_ids,
+ },
+};
+module_platform_driver(otto_wdt_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Sander Vanheule <[email protected]>");
+MODULE_DESCRIPTION("Realtek Otto watchdog timer driver");
--
2.31.1
Add a binding description for Realtek's watchdog timer as found on
several of their MIPS-based SoCs (codenamed Otto), such as the RTL838x,
RTL839x, and RTL930x series of switch SoCs.
Signed-off-by: Sander Vanheule <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
--
v2:
- add realtek,rtl9300-wdt compatible
- make interrupts property required
- add Rob's Reviewed-by tag
---
.../bindings/watchdog/realtek,otto-wdt.yaml | 91 +++++++++++++++++++
1 file changed, 91 insertions(+)
create mode 100644 Documentation/devicetree/bindings/watchdog/realtek,otto-wdt.yaml
diff --git a/Documentation/devicetree/bindings/watchdog/realtek,otto-wdt.yaml b/Documentation/devicetree/bindings/watchdog/realtek,otto-wdt.yaml
new file mode 100644
index 000000000000..11b220a5e0f6
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/realtek,otto-wdt.yaml
@@ -0,0 +1,91 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/watchdog/realtek,otto-wdt.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Realtek Otto watchdog timer
+
+maintainers:
+ - Sander Vanheule <[email protected]>
+
+description: |
+ The timer has two timeout phases. Both phases have a maximum duration of 32
+ prescaled clock ticks, which is ca. 43s with a bus clock of 200MHz. The
+ minimum duration of each phase is one tick. Each phase can trigger an
+ interrupt, although the phase 2 interrupt will occur with the system reset.
+ - Phase 1: During this phase, the WDT can be pinged to reset the timeout.
+ - Phase 2: Starts after phase 1 has timed out, and only serves to give the
+ system some time to clean up, or notify others that it's going to reset.
+ During this phase, pinging the WDT has no effect, and a reset is
+ unavoidable, unless the WDT is disabled.
+
+allOf:
+ - $ref: watchdog.yaml#
+
+properties:
+ compatible:
+ enum:
+ - realtek,rtl8380-wdt
+ - realtek,rtl8390-wdt
+ - realtek,rtl9300-wdt
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ interrupts:
+ items:
+ - description: interrupt specifier for pretimeout
+ - description: interrupt specifier for timeout
+
+ interrupt-names:
+ items:
+ - const: phase1
+ - const: phase2
+
+ realtek,reset-mode:
+ $ref: /schemas/types.yaml#/definitions/string
+ description: |
+ Specify how the system is reset after a timeout. Defaults to "cpu" if
+ left unspecified.
+ oneOf:
+ - description: Reset the entire chip
+ const: soc
+ - description: |
+ Reset the CPU and IPsec engine, but leave other peripherals untouched
+ const: cpu
+ - description: |
+ Reset the execution pointer, but don't actually reset any hardware
+ const: software
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - interrupts
+
+unevaluatedProperties: false
+
+dependencies:
+ interrupts: [ interrupt-names ]
+
+examples:
+ - |
+ watchdog: watchdog@3150 {
+ compatible = "realtek,rtl8380-wdt";
+ reg = <0x3150 0xc>;
+
+ realtek,reset-mode = "soc";
+
+ clocks = <&lxbus_clock>;
+ timeout-sec = <20>;
+
+ interrupt-parent = <&rtlintc>;
+ interrupt-names = "phase1", "phase2";
+ interrupts = <19>, <18>;
+ };
+
+...
--
2.31.1
On Thu, 2021-11-04 at 09:59 +0100, Sander Vanheule wrote:
> + do {
> + if (prescale > OTTO_WDT_PRESCALE_MAX)
> + return -EINVAL;
> +
> + tick_ms = otto_wdt_tick_ms(ctrl, prescale);
> + total_ticks = div_round_ticks(timeout_ms, tick_ms, 2);
> + phase1_ticks = div_round_ticks(timeout_ms - pretimeout_ms, tick_ms,
> 1);
> + phase2_ticks = total_ticks - phase1_ticks;
> +
> + prescale++;
> + } while (phase1_ticks > OTTO_WDT_PHASE_TICKS_MAX
> + || phase2_ticks > OTTO_WDT_PHASE_TICKS_MAX);
> +
> + v = ioread32(ctrl->base + OTTO_WDT_REG_CTRL);
> +
> + v &= ~(OTTO_WDT_CTRL_PRESCALE | OTTO_WDT_CTRL_PHASE1 |
> OTTO_WDT_CTRL_PHASE2);
> + v |= FIELD_PREP(OTTO_WDT_CTRL_PHASE1, phase1_ticks - 1);
> + v |= FIELD_PREP(OTTO_WDT_CTRL_PHASE2, phase2_ticks - 1);
> + v |= FIELD_PREP(OTTO_WDT_CTRL_PRESCALE, prescale);
I dropped the prescale_next variable here, but now the wrong prescale value is used
after the loop. I'll send out a v3 shortly.
Best,
Sander