The RRADC is responsible for reading data about the current and
voltage from the USB or DC in jacks, it can also read the battery
ID (resistence) and some temperatures. It is found on the PMI8998 and
PM660 Qualcomm PMICs.
The RRADC has to calibrate some ADC values based on which chip fab
the PMIC was produced in, to facilitate this the patch
("mfd: qcom-spmi-pmic: expose the PMIC revid information to clients")
exposes the PMIC revision information as a struct and registers it
as driver data in the Qualcomm SPMI PMIC driver so that it can be
read by the RRADC.
Changes since v1:
* Rework the RRADC driver based on Jonathan's feedback
* Pick up Rob's reviewed by for the dt-binding patch.
Caleb Connolly (7):
mfd: qcom-spmi-pmic: expose the PMIC revid information to clients
dt-bindings: iio: adc: document qcom-spmi-rradc
iio: adc: qcom-spmi-rradc: introduce round robin adc
arm64: dts: qcom: pmi8998: add rradc node
arm64: dts: qcom: sdm845-oneplus: enable rradc
arm64: dts: qcom: sdm845-db845c: enable rradc
arm64: dts: qcom: sdm845-xiaomi-beryllium: enable RRADC
.../bindings/iio/adc/qcom,spmi-rradc.yaml | 54 +
arch/arm64/boot/dts/qcom/pmi8998.dtsi | 8 +
arch/arm64/boot/dts/qcom/sdm845-db845c.dts | 4 +
.../boot/dts/qcom/sdm845-oneplus-common.dtsi | 4 +
.../boot/dts/qcom/sdm845-xiaomi-beryllium.dts | 4 +
drivers/iio/adc/Kconfig | 13 +
drivers/iio/adc/Makefile | 1 +
drivers/iio/adc/qcom-spmi-rradc.c | 1070 +++++++++++++++++
drivers/mfd/qcom-spmi-pmic.c | 108 +-
include/soc/qcom/qcom-pmic.h | 63 +
10 files changed, 1272 insertions(+), 57 deletions(-)
create mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,spmi-rradc.yaml
create mode 100644 drivers/iio/adc/qcom-spmi-rradc.c
create mode 100644 include/soc/qcom/qcom-pmic.h
--
2.34.1
Enable the RRADC for the OnePlus 6.
Signed-off-by: Caleb Connolly <[email protected]>
---
arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi
index 3e04aeb479d1..9feda49b2f12 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi
@@ -450,6 +450,10 @@ pinconf {
};
};
+&pmi8998_rradc {
+ status = "okay";
+};
+
&qupv3_id_1 {
status = "okay";
};
--
2.34.1
Enable the Round Robin ADC for the db845c.
Signed-off-by: Caleb Connolly <[email protected]>
---
arch/arm64/boot/dts/qcom/sdm845-db845c.dts | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
index 13f80a0b6faa..1c452b458121 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
@@ -595,6 +595,10 @@ resin {
};
};
+&pmi8998_rradc {
+ status = "okay";
+};
+
/* QUAT I2S Uses 4 I2S SD Lines for audio on LT9611 HDMI Bridge */
&q6afedai {
qi2s@22 {
--
2.34.1
Enable the PMI8998 RRADC.
Signed-off-by: Caleb Connolly <[email protected]>
---
arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
index 580d4cc1296f..481132b0cee4 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
@@ -312,6 +312,10 @@ resin {
};
};
+&pmi8998_rradc {
+ status = "okay";
+};
+
/* QUAT I2S Uses 1 I2S SD Line for audio on TAS2559/60 amplifiers */
&q6afedai {
qi2s@22 {
--
2.34.1
Add dt-binding docs for the Qualcomm SPMI RRADC found in PMICs like
PMI8998 and PMI8994
Signed-off-by: Caleb Connolly <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
---
.../bindings/iio/adc/qcom,spmi-rradc.yaml | 54 +++++++++++++++++++
1 file changed, 54 insertions(+)
create mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,spmi-rradc.yaml
diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-rradc.yaml b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-rradc.yaml
new file mode 100644
index 000000000000..11d47c46a48d
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-rradc.yaml
@@ -0,0 +1,54 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/qcom,spmi-rradc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm's SPMI PMIC Round Robin ADC
+
+maintainers:
+ - Caleb Connolly <[email protected]>
+
+description: |
+ The Qualcomm SPMI Round Robin ADC (RRADC) provides interface to clients to read the
+ voltage, current and temperature for supported peripherals such as the battery thermistor
+ die temperature, charger temperature, USB and DC input voltage / current and battery ID
+ resistor.
+
+properties:
+ compatible:
+ enum:
+ - qcom,pmi8998-rradc
+ - qcom,pm660-rradc
+
+ reg:
+ description: rradc base address and length in the SPMI PMIC register map
+ maxItems: 1
+
+ qcom,batt-id-delay-ms:
+ description:
+ Sets the hardware settling time for the battery ID resistor.
+ enum: [0, 1, 4, 12, 20, 40, 60, 80]
+
+ "#io-channel-cells":
+ const: 1
+
+required:
+ - compatible
+ - reg
+
+additionalProperties: false
+
+examples:
+ - |
+ pmic {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmic_rradc: adc@4500 {
+ compatible = "qcom,pmi8998-rradc";
+ reg = <0x4500>;
+ #io-channel-cells = <1>;
+ };
+ };
+...
--
2.34.1
The Round Robin ADC is responsible for reading data about the rate of
charge from the USB or DC in jacks, it can also read the battery
ID (resistence) and some temperatures. It is found on the PMI8998 and
PM660 Qualcomm PMICs.
Signed-off-by: Caleb Connolly <[email protected]>
---
drivers/iio/adc/Kconfig | 13 +
drivers/iio/adc/Makefile | 1 +
drivers/iio/adc/qcom-spmi-rradc.c | 1070 +++++++++++++++++++++++++++++
3 files changed, 1084 insertions(+)
create mode 100644 drivers/iio/adc/qcom-spmi-rradc.c
diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index 3363af15a43f..37f18ee4c4c5 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -812,6 +812,19 @@ config QCOM_PM8XXX_XOADC
To compile this driver as a module, choose M here: the module
will be called qcom-pm8xxx-xoadc.
+config QCOM_SPMI_RRADC
+ tristate "Qualcomm SPMI RRADC"
+ depends on MFD_SPMI_PMIC
+ help
+ This is for the PMIC Round Robin ADC driver.
+
+ This driver exposes the battery ID resistor, battery thermal, PMIC die
+ temperature, charger USB in and DC in voltage and current.
+
+ To compile this driver as a module, choose M here: the module will
+ be called qcom-qpmi-rradc.
+
+
config QCOM_SPMI_IADC
tristate "Qualcomm SPMI PMIC current ADC"
depends on SPMI
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index d3f53549720c..ca8bad549175 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -77,6 +77,7 @@ obj-$(CONFIG_NPCM_ADC) += npcm_adc.o
obj-$(CONFIG_PALMAS_GPADC) += palmas_gpadc.o
obj-$(CONFIG_QCOM_SPMI_ADC5) += qcom-spmi-adc5.o
obj-$(CONFIG_QCOM_SPMI_IADC) += qcom-spmi-iadc.o
+obj-$(CONFIG_QCOM_SPMI_RRADC) += qcom-spmi-rradc.o
obj-$(CONFIG_QCOM_VADC_COMMON) += qcom-vadc-common.o
obj-$(CONFIG_QCOM_SPMI_VADC) += qcom-spmi-vadc.o
obj-$(CONFIG_QCOM_PM8XXX_XOADC) += qcom-pm8xxx-xoadc.o
diff --git a/drivers/iio/adc/qcom-spmi-rradc.c b/drivers/iio/adc/qcom-spmi-rradc.c
new file mode 100644
index 000000000000..e5c3b249bc0f
--- /dev/null
+++ b/drivers/iio/adc/qcom-spmi-rradc.c
@@ -0,0 +1,1070 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2021 Linaro Limited.
+ * Author: Caleb Connolly <[email protected]>
+ *
+ * This driver is for the Round Robin ADC found in the pmi8998 and pm660 PMICs.
+ */
+
+#include <linux/delay.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/types.h>
+#include <linux/kernel.h>
+#include <linux/math64.h>
+#include <linux/minmax.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/power_supply.h>
+#include <linux/regmap.h>
+#include <linux/spmi.h>
+#include <linux/types.h>
+#include <asm-generic/unaligned.h>
+#include <linux/units.h>
+#include <soc/qcom/qcom-pmic.h>
+
+#define RR_ADC_EN_CTL 0x46
+#define RR_ADC_SKIN_TEMP_LSB 0x50
+#define RR_ADC_SKIN_TEMP_MSB 0x51
+#define RR_ADC_RR_ADC_CTL 0x52
+#define RR_ADC_ADC_CTL_CONTINUOUS_SEL BIT(3)
+#define RR_ADC_ADC_LOG 0x53
+#define RR_ADC_ADC_LOG_CLR_CTRL BIT(0)
+
+#define RR_ADC_FAKE_BATT_LOW_LSB 0x58
+#define RR_ADC_FAKE_BATT_LOW_MSB 0x59
+#define RR_ADC_FAKE_BATT_HIGH_LSB 0x5A
+#define RR_ADC_FAKE_BATT_HIGH_MSB 0x5B
+
+#define RR_ADC_BATT_ID_CTRL 0x60
+#define RR_ADC_BATT_ID_CTRL_CHANNEL_CONV BIT(0)
+#define RR_ADC_BATT_ID_TRIGGER 0x61
+#define RR_ADC_BATT_ID_STS 0x62
+#define RR_ADC_BATT_ID_CFG 0x63
+#define BATT_ID_SETTLE_MASK GENMASK(7, 5)
+#define RR_ADC_BATT_ID_5_LSB 0x66
+#define RR_ADC_BATT_ID_5_MSB 0x67
+#define RR_ADC_BATT_ID_15_LSB 0x68
+#define RR_ADC_BATT_ID_15_MSB 0x69
+#define RR_ADC_BATT_ID_150_LSB 0x6A
+#define RR_ADC_BATT_ID_150_MSB 0x6B
+
+#define RR_ADC_BATT_THERM_CTRL 0x70
+#define RR_ADC_BATT_THERM_TRIGGER 0x71
+#define RR_ADC_BATT_THERM_STS 0x72
+#define RR_ADC_BATT_THERM_CFG 0x73
+#define RR_ADC_BATT_THERM_LSB 0x74
+#define RR_ADC_BATT_THERM_MSB 0x75
+#define RR_ADC_BATT_THERM_FREQ 0x76
+
+#define RR_ADC_AUX_THERM_CTRL 0x80
+#define RR_ADC_AUX_THERM_TRIGGER 0x81
+#define RR_ADC_AUX_THERM_STS 0x82
+#define RR_ADC_AUX_THERM_CFG 0x83
+#define RR_ADC_AUX_THERM_LSB 0x84
+#define RR_ADC_AUX_THERM_MSB 0x85
+
+#define RR_ADC_SKIN_HOT 0x86
+#define RR_ADC_SKIN_TOO_HOT 0x87
+
+#define RR_ADC_AUX_THERM_C1 0x88
+#define RR_ADC_AUX_THERM_C2 0x89
+#define RR_ADC_AUX_THERM_C3 0x8A
+#define RR_ADC_AUX_THERM_HALF_RANGE 0x8B
+
+#define RR_ADC_USB_IN_V_CTRL 0x90
+#define RR_ADC_USB_IN_V_TRIGGER 0x91
+#define RR_ADC_USB_IN_V_STS 0x92
+#define RR_ADC_USB_IN_V_LSB 0x94
+#define RR_ADC_USB_IN_V_MSB 0x95
+#define RR_ADC_USB_IN_I_CTRL 0x98
+#define RR_ADC_USB_IN_I_TRIGGER 0x99
+#define RR_ADC_USB_IN_I_STS 0x9A
+#define RR_ADC_USB_IN_I_LSB 0x9C
+#define RR_ADC_USB_IN_I_MSB 0x9D
+
+#define RR_ADC_DC_IN_V_CTRL 0xA0
+#define RR_ADC_DC_IN_V_TRIGGER 0xA1
+#define RR_ADC_DC_IN_V_STS 0xA2
+#define RR_ADC_DC_IN_V_LSB 0xA4
+#define RR_ADC_DC_IN_V_MSB 0xA5
+#define RR_ADC_DC_IN_I_CTRL 0xA8
+#define RR_ADC_DC_IN_I_TRIGGER 0xA9
+#define RR_ADC_DC_IN_I_STS 0xAA
+#define RR_ADC_DC_IN_I_LSB 0xAC
+#define RR_ADC_DC_IN_I_MSB 0xAD
+
+#define RR_ADC_PMI_DIE_TEMP_CTRL 0xB0
+#define RR_ADC_PMI_DIE_TEMP_TRIGGER 0xB1
+#define RR_ADC_PMI_DIE_TEMP_STS 0xB2
+#define RR_ADC_PMI_DIE_TEMP_CFG 0xB3
+#define RR_ADC_PMI_DIE_TEMP_LSB 0xB4
+#define RR_ADC_PMI_DIE_TEMP_MSB 0xB5
+
+#define RR_ADC_CHARGER_TEMP_CTRL 0xB8
+#define RR_ADC_CHARGER_TEMP_TRIGGER 0xB9
+#define RR_ADC_CHARGER_TEMP_STS 0xBA
+#define RR_ADC_CHARGER_TEMP_CFG 0xBB
+#define RR_ADC_CHARGER_TEMP_LSB 0xBC
+#define RR_ADC_CHARGER_TEMP_MSB 0xBD
+#define RR_ADC_CHARGER_HOT 0xBE
+#define RR_ADC_CHARGER_TOO_HOT 0xBF
+
+#define RR_ADC_GPIO_CTRL 0xC0
+#define RR_ADC_GPIO_TRIGGER 0xC1
+#define RR_ADC_GPIO_STS 0xC2
+#define RR_ADC_GPIO_LSB 0xC4
+#define RR_ADC_GPIO_MSB 0xC5
+
+#define RR_ADC_ATEST_CTRL 0xC8
+#define RR_ADC_ATEST_TRIGGER 0xC9
+#define RR_ADC_ATEST_STS 0xCA
+#define RR_ADC_ATEST_LSB 0xCC
+#define RR_ADC_ATEST_MSB 0xCD
+#define RR_ADC_SEC_ACCESS 0xD0
+
+#define RR_ADC_PERPH_RESET_CTL2 0xD9
+#define RR_ADC_PERPH_RESET_CTL3 0xDA
+#define RR_ADC_PERPH_RESET_CTL4 0xDB
+#define RR_ADC_INT_TEST1 0xE0
+#define RR_ADC_INT_TEST_VAL 0xE1
+
+#define RR_ADC_TM_TRIGGER_CTRLS 0xE2
+#define RR_ADC_TM_ADC_CTRLS 0xE3
+#define RR_ADC_TM_CNL_CTRL 0xE4
+#define RR_ADC_TM_BATT_ID_CTRL 0xE5
+#define RR_ADC_TM_THERM_CTRL 0xE6
+#define RR_ADC_TM_CONV_STS 0xE7
+#define RR_ADC_TM_ADC_READ_LSB 0xE8
+#define RR_ADC_TM_ADC_READ_MSB 0xE9
+#define RR_ADC_TM_ATEST_MUX_1 0xEA
+#define RR_ADC_TM_ATEST_MUX_2 0xEB
+#define RR_ADC_TM_REFERENCES 0xED
+#define RR_ADC_TM_MISC_CTL 0xEE
+#define RR_ADC_TM_RR_CTRL 0xEF
+
+#define RR_ADC_TRIGGER_EVERY_CYCLE BIT(7)
+#define RR_ADC_TRIGGER_CTL BIT(0)
+
+#define RR_ADC_BATT_ID_RANGE 820
+
+#define RR_ADC_BITS 10
+#define RR_ADC_CHAN_MAX_VALUE (1 << RR_ADC_BITS)
+#define RR_ADC_FS_VOLTAGE_MV 2500
+
+/* BATT_THERM 0.25K/LSB */
+#define RR_ADC_BATT_THERM_LSB_K 4
+
+#define RR_ADC_TEMP_FS_VOLTAGE_NUM 5000000
+#define RR_ADC_TEMP_FS_VOLTAGE_DEN 3
+#define RR_ADC_DIE_TEMP_OFFSET 601400
+#define RR_ADC_DIE_TEMP_SLOPE 2
+#define RR_ADC_DIE_TEMP_OFFSET_MILLI_DEGC 25000
+
+#define RR_ADC_CHG_TEMP_GF_OFFSET_UV 1303168
+#define RR_ADC_CHG_TEMP_GF_SLOPE_UV_PER_C 3784
+#define RR_ADC_CHG_TEMP_SMIC_OFFSET_UV 1338433
+#define RR_ADC_CHG_TEMP_SMIC_SLOPE_UV_PER_C 3655
+#define RR_ADC_CHG_TEMP_660_GF_OFFSET_UV 1309001
+#define RR_ADC_CHG_TEMP_660_GF_SLOPE_UV_PER_C 3403
+#define RR_ADC_CHG_TEMP_660_SMIC_OFFSET_UV 1295898
+#define RR_ADC_CHG_TEMP_660_SMIC_SLOPE_UV_PER_C 3596
+#define RR_ADC_CHG_TEMP_660_MGNA_OFFSET_UV 1314779
+#define RR_ADC_CHG_TEMP_660_MGNA_SLOPE_UV_PER_C 3496
+#define RR_ADC_CHG_TEMP_OFFSET_MILLI_DEGC 25000
+#define RR_ADC_CHG_THRESHOLD_SCALE 4
+
+#define RR_ADC_VOLT_INPUT_FACTOR 8
+#define RR_ADC_CURR_INPUT_FACTOR 2000
+#define RR_ADC_CURR_USBIN_INPUT_FACTOR_MIL 1886
+#define RR_ADC_CURR_USBIN_660_FACTOR_MIL 9
+#define RR_ADC_CURR_USBIN_660_UV_VAL 579500
+
+#define RR_ADC_GPIO_FS_RANGE 5000
+#define RR_ADC_COHERENT_CHECK_RETRY 5
+#define RR_ADC_CHAN_MAX_CONTINUOUS_BUFFER_LEN 16
+
+#define RR_ADC_STS_CHANNEL_READING_MASK 0x3
+#define RR_ADC_STS_CHANNEL_STS 0x2
+
+#define RR_ADC_TP_REV_VERSION1 21
+#define RR_ADC_TP_REV_VERSION2 29
+#define RR_ADC_TP_REV_VERSION3 32
+
+#define RRADC_BATT_ID_DELAY_MAX 8
+
+enum rradc_channel_id {
+ RR_ADC_BATT_ID = 0,
+ RR_ADC_BATT_THERM,
+ RR_ADC_SKIN_TEMP,
+ RR_ADC_USBIN_I,
+ RR_ADC_USBIN_V,
+ RR_ADC_DCIN_I,
+ RR_ADC_DCIN_V,
+ RR_ADC_DIE_TEMP,
+ RR_ADC_CHG_TEMP,
+ RR_ADC_GPIO,
+ RR_ADC_CHG_HOT_TEMP,
+ RR_ADC_CHG_TOO_HOT_TEMP,
+ RR_ADC_SKIN_HOT_TEMP,
+ RR_ADC_SKIN_TOO_HOT_TEMP,
+ RR_ADC_CHAN_MAX
+};
+
+struct rradc_chip;
+
+/**
+ * struct rradc_channel - rradc channel data
+ * @lsb: Channel least significant byte
+ * @status: Channel status address
+ * @size: number of bytes to read
+ * @trigger_addr: Trigger address, trigger is only used on some channels
+ * @trigger_mask: Trigger mask
+ * @scale: Channel scale callback
+ */
+struct rradc_channel {
+ u8 lsb;
+ u8 status;
+ int size;
+ int trigger_addr;
+ int trigger_mask;
+ int (*scale)(struct rradc_chip *chip, u16 adc_code, int *result);
+};
+
+struct rradc_chip {
+ struct device *dev;
+ struct qcom_spmi_pmic *pmic;
+ struct mutex lock;
+ struct regmap *regmap;
+ u32 base;
+ int batt_id_delay;
+ u16 batt_id_data;
+};
+
+static const int batt_id_delays[] = { 0, 1, 4, 12, 20, 40, 60, 80 };
+static const struct rradc_channel rradc_chans[RR_ADC_CHAN_MAX];
+static const struct iio_chan_spec rradc_iio_chans[RR_ADC_CHAN_MAX];
+
+static int rradc_read(struct rradc_chip *chip, u16 addr, u8 *data, int len)
+{
+ int ret, retry_cnt = 0;
+ u8 data_check[RR_ADC_CHAN_MAX_CONTINUOUS_BUFFER_LEN];
+
+ if (len > RR_ADC_CHAN_MAX_CONTINUOUS_BUFFER_LEN) {
+ dev_err(chip->dev,
+ "Can't read more than %d bytes, but asked to read %d bytes.\n",
+ RR_ADC_CHAN_MAX_CONTINUOUS_BUFFER_LEN, len);
+ return -EINVAL;
+ }
+
+ while (retry_cnt < RR_ADC_COHERENT_CHECK_RETRY) {
+ ret = regmap_bulk_read(chip->regmap, chip->base + addr, data,
+ len);
+ if (ret < 0) {
+ dev_err(chip->dev, "rr_adc reg 0x%x failed :%d\n", addr,
+ ret);
+ return ret;
+ }
+
+ ret = regmap_bulk_read(chip->regmap, chip->base + addr,
+ data_check, len);
+ if (ret < 0) {
+ dev_err(chip->dev, "rr_adc reg 0x%x failed :%d\n", addr,
+ ret);
+ return ret;
+ }
+
+ if (memcmp(data, data_check, len) != 0) {
+ retry_cnt++;
+ dev_dbg(chip->dev,
+ "coherent read error, retry_cnt:%d\n",
+ retry_cnt);
+ continue;
+ }
+
+ break;
+ }
+
+ if (retry_cnt == RR_ADC_COHERENT_CHECK_RETRY)
+ dev_err(chip->dev, "Retry exceeded for coherrency check\n");
+
+ return ret;
+}
+
+static int rradc_get_fab_coeff(struct rradc_chip *chip, int64_t *offset,
+ int64_t *slope)
+{
+ if (chip->pmic->subtype == PM660_SUBTYPE) {
+ switch (chip->pmic->fab_id) {
+ case PM660_FAB_ID_GF:
+ *offset = RR_ADC_CHG_TEMP_660_GF_OFFSET_UV;
+ *slope = RR_ADC_CHG_TEMP_660_GF_SLOPE_UV_PER_C;
+ break;
+ case PM660_FAB_ID_TSMC:
+ *offset = RR_ADC_CHG_TEMP_660_SMIC_OFFSET_UV;
+ *slope = RR_ADC_CHG_TEMP_660_SMIC_SLOPE_UV_PER_C;
+ break;
+ default:
+ *offset = RR_ADC_CHG_TEMP_660_MGNA_OFFSET_UV;
+ *slope = RR_ADC_CHG_TEMP_660_MGNA_SLOPE_UV_PER_C;
+ }
+ } else if (chip->pmic->subtype == PMI8998_SUBTYPE) {
+ switch (chip->pmic->fab_id) {
+ case PMI8998_FAB_ID_GF:
+ *offset = RR_ADC_CHG_TEMP_GF_OFFSET_UV;
+ *slope = RR_ADC_CHG_TEMP_GF_SLOPE_UV_PER_C;
+ break;
+ case PMI8998_FAB_ID_SMIC:
+ *offset = RR_ADC_CHG_TEMP_SMIC_OFFSET_UV;
+ *slope = RR_ADC_CHG_TEMP_SMIC_SLOPE_UV_PER_C;
+ break;
+ default:
+ return -EINVAL;
+ }
+ } else {
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+/*
+ * These functions explicitly cast int64_t to int.
+ * They will never overflow, as the values are small enough.
+ */
+static int rradc_post_process_batt_id(struct rradc_chip *chip, u16 adc_code,
+ int *result_ohms)
+{
+ uint32_t current_value;
+ int64_t r_id;
+
+ current_value = chip->batt_id_data;
+ r_id = ((int64_t)adc_code * RR_ADC_FS_VOLTAGE_MV);
+ r_id = div64_s64(r_id, (RR_ADC_CHAN_MAX_VALUE * current_value));
+ *result_ohms = (int)(r_id * MILLI);
+
+ return 0;
+}
+
+static int rradc_post_process_therm(struct rradc_chip *chip, u16 adc_code,
+ int *result_millidegc)
+{
+ int64_t temp;
+
+ /* K = code/4 */
+ temp = ((int64_t)adc_code * MILLI);
+ temp = div64_s64(temp, RR_ADC_BATT_THERM_LSB_K);
+ *result_millidegc = (int)milli_kelvin_to_millicelsius(temp);
+
+ return 0;
+}
+
+static int rradc_post_process_volt(struct rradc_chip *chip, u16 adc_code,
+ int *result_uv)
+{
+ int64_t uv;
+
+ /* 8x input attenuation; 2.5V ADC full scale */
+ uv = ((int64_t)adc_code * RR_ADC_VOLT_INPUT_FACTOR);
+ uv *= (RR_ADC_FS_VOLTAGE_MV * MILLI);
+ uv = div64_s64(uv, RR_ADC_CHAN_MAX_VALUE);
+ *result_uv = (int)uv;
+
+ return 0;
+}
+
+static int rradc_post_process_usbin_curr(struct rradc_chip *chip, u16 adc_code,
+ int *result_ua)
+{
+ int64_t ua;
+
+ /* scale * V/A; 2.5V ADC full scale */
+ ua = ((int64_t)adc_code * RR_ADC_CURR_USBIN_INPUT_FACTOR_MIL);
+ ua *= (RR_ADC_FS_VOLTAGE_MV * MILLI);
+ ua = div64_s64(ua, (RR_ADC_CHAN_MAX_VALUE * 10));
+ *result_ua = (int)ua;
+
+ return 0;
+}
+
+static int rradc_post_process_dcin_curr(struct rradc_chip *chip, u16 adc_code,
+ int *result_ua)
+{
+ int64_t ua;
+
+ /* 0.5 V/A; 2.5V ADC full scale */
+ ua = ((int64_t)adc_code * RR_ADC_CURR_INPUT_FACTOR);
+ ua *= (RR_ADC_FS_VOLTAGE_MV * MILLI);
+ ua = div64_s64(ua, (RR_ADC_CHAN_MAX_VALUE * 1000));
+ *result_ua = (int)ua;
+
+ return 0;
+}
+
+static int rradc_post_process_die_temp(struct rradc_chip *chip, u16 adc_code,
+ int *result_millidegc)
+{
+ int64_t temp;
+
+ temp = ((int64_t)adc_code * RR_ADC_TEMP_FS_VOLTAGE_NUM);
+ temp = div64_s64(temp,
+ (RR_ADC_TEMP_FS_VOLTAGE_DEN * RR_ADC_CHAN_MAX_VALUE));
+ temp -= RR_ADC_DIE_TEMP_OFFSET;
+ temp = div64_s64(temp, RR_ADC_DIE_TEMP_SLOPE);
+ temp += RR_ADC_DIE_TEMP_OFFSET_MILLI_DEGC;
+ *result_millidegc = (int)temp;
+
+ return 0;
+}
+
+static int rradc_post_process_chg_temp_hot(struct rradc_chip *chip,
+ u16 adc_code, int *result_millidegc)
+{
+ int64_t uv, offset, slope;
+ int ret;
+
+ ret = rradc_get_fab_coeff(chip, &offset, &slope);
+ if (ret < 0) {
+ dev_err(chip->dev, "Unable to get fab id coefficients\n");
+ return -EINVAL;
+ }
+
+ uv = (int64_t)adc_code * RR_ADC_CHG_THRESHOLD_SCALE;
+ uv = uv * RR_ADC_TEMP_FS_VOLTAGE_NUM;
+ uv = div64_s64(uv,
+ (RR_ADC_TEMP_FS_VOLTAGE_DEN * RR_ADC_CHAN_MAX_VALUE));
+ uv = offset - uv;
+ uv = div64_s64((uv * MILLI), slope);
+ uv = uv + RR_ADC_CHG_TEMP_OFFSET_MILLI_DEGC;
+ *result_millidegc = (int)uv;
+
+ return 0;
+}
+
+static int rradc_post_process_skin_temp_hot(struct rradc_chip *chip,
+ u16 adc_code, int *result_millidegc)
+{
+ int64_t temp;
+
+ temp = (int64_t)adc_code;
+ temp = (div64_s64(temp, 2) - 30) * MILLI;
+ *result_millidegc = (int)temp;
+
+ return 0;
+}
+
+static int rradc_post_process_chg_temp(struct rradc_chip *chip, u16 adc_code,
+ int *result_millidegc)
+{
+ int64_t uv, offset, slope;
+ int ret;
+
+ ret = rradc_get_fab_coeff(chip, &offset, &slope);
+ if (ret < 0) {
+ dev_err(chip->dev, "Unable to get fab id coefficients\n");
+ return -EINVAL;
+ }
+
+ uv = ((int64_t)adc_code * RR_ADC_TEMP_FS_VOLTAGE_NUM);
+ uv = div64_s64(uv,
+ (RR_ADC_TEMP_FS_VOLTAGE_DEN * RR_ADC_CHAN_MAX_VALUE));
+ uv = offset - uv;
+ uv = div64_s64((uv * MILLI), slope);
+ uv += RR_ADC_CHG_TEMP_OFFSET_MILLI_DEGC;
+ *result_millidegc = (int)uv;
+
+ return 0;
+}
+
+static int rradc_post_process_gpio(struct rradc_chip *chip, u16 adc_code,
+ int *result_mv)
+{
+ int64_t mv;
+
+ /* 5V ADC full scale, 10 bit */
+ mv = ((int64_t)adc_code * RR_ADC_GPIO_FS_RANGE);
+ mv = div64_s64(mv, RR_ADC_CHAN_MAX_VALUE);
+ *result_mv = (int)mv;
+
+ return 0;
+}
+
+static int rradc_enable_continuous_mode(struct rradc_chip *chip)
+{
+ int ret;
+
+ /* Clear channel log */
+ ret = regmap_update_bits(chip->regmap, chip->base + RR_ADC_ADC_LOG,
+ RR_ADC_ADC_LOG_CLR_CTRL,
+ RR_ADC_ADC_LOG_CLR_CTRL);
+ if (ret < 0) {
+ dev_err(chip->dev, "log ctrl update to clear failed:%d\n", ret);
+ return ret;
+ }
+
+ ret = regmap_update_bits(chip->regmap, chip->base + RR_ADC_ADC_LOG,
+ RR_ADC_ADC_LOG_CLR_CTRL, 0);
+ if (ret < 0) {
+ dev_err(chip->dev, "log ctrl update to not clear failed:%d\n",
+ ret);
+ return ret;
+ }
+
+ /* Switch to continuous mode */
+ ret = regmap_update_bits(chip->regmap, chip->base + RR_ADC_RR_ADC_CTL,
+ RR_ADC_ADC_CTL_CONTINUOUS_SEL,
+ RR_ADC_ADC_CTL_CONTINUOUS_SEL);
+ if (ret < 0)
+ dev_err(chip->dev, "Update to continuous mode failed:%d\n",
+ ret);
+
+ return ret;
+}
+
+static int rradc_disable_continuous_mode(struct rradc_chip *chip)
+{
+ int ret;
+
+ /* Switch to non continuous mode */
+ ret = regmap_update_bits(chip->regmap, chip->base + RR_ADC_RR_ADC_CTL,
+ RR_ADC_ADC_CTL_CONTINUOUS_SEL, 0);
+ if (ret < 0)
+ dev_err(chip->dev, "Update to non-continuous mode failed:%d\n",
+ ret);
+
+ return ret;
+}
+
+static bool rradc_is_ready(struct rradc_chip *chip,
+ enum rradc_channel_id chan_id)
+{
+ const struct rradc_channel *chan = &rradc_chans[chan_id];
+ int ret;
+ unsigned int status, mask;
+
+ /* BATT_ID STS bit does not get set initially */
+ switch (chan_id) {
+ case RR_ADC_BATT_ID:
+ mask = RR_ADC_STS_CHANNEL_STS;
+ break;
+ default:
+ mask = RR_ADC_STS_CHANNEL_READING_MASK;
+ break;
+ }
+
+ ret = regmap_read(chip->regmap, chip->base + chan->status, &status);
+ if (ret < 0 || !(status & mask))
+ return false;
+
+ return true;
+}
+
+static int rradc_read_status_in_cont_mode(struct rradc_chip *chip,
+ enum rradc_channel_id chan_id)
+{
+ const struct rradc_channel *chan = &rradc_chans[chan_id];
+ const struct iio_chan_spec *iio_chan = &rradc_iio_chans[chan_id];
+ int ret;
+
+ if (chan->trigger_mask == 0) {
+ dev_err(chip->dev, "Channel doesn't have a trigger mask\n");
+ return -EINVAL;
+ }
+
+ ret = regmap_update_bits(chip->regmap, chip->base + chan->trigger_addr,
+ chan->trigger_mask, chan->trigger_mask);
+ if (ret < 0) {
+ dev_err(chip->dev,
+ "Failed to apply trigger for channel '%s' ret=%d\n",
+ iio_chan->datasheet_name, ret);
+ return ret;
+ }
+
+ ret = rradc_enable_continuous_mode(chip);
+ if (ret < 0) {
+ dev_err(chip->dev, "Failed to switch to continuous mode\n");
+ goto disable_trigger;
+ }
+
+ if (!rradc_is_ready(chip, chan_id))
+ dev_err(chip->dev, "channel '%s' is not ready\n",
+ iio_chan->datasheet_name);
+
+ ret = rradc_disable_continuous_mode(chip);
+ if (ret < 0)
+ dev_err(chip->dev, "Failed to switch to non continuous mode\n");
+
+disable_trigger:
+ ret = regmap_update_bits(chip->regmap, chip->base + chan->trigger_addr,
+ chan->trigger_mask, 0);
+ if (ret < 0)
+ dev_err(chip->dev,
+ "Failed to apply trigger for channel '%s' ret=%d\n",
+ iio_chan->datasheet_name, ret);
+
+ return ret;
+}
+
+static int rradc_prepare_batt_id_conversion(struct rradc_chip *chip,
+ enum rradc_channel_id chan_id,
+ u16 *data)
+{
+ int ret, batt_id_delay;
+
+ ret = regmap_update_bits(chip->regmap, chip->base + RR_ADC_BATT_ID_CTRL,
+ RR_ADC_BATT_ID_CTRL_CHANNEL_CONV,
+ RR_ADC_BATT_ID_CTRL_CHANNEL_CONV);
+ if (ret < 0) {
+ dev_err(chip->dev, "Enabling BATT ID channel failed:%d\n", ret);
+ return ret;
+ }
+
+ if (chip->batt_id_delay != -EINVAL) {
+ batt_id_delay =
+ FIELD_PREP(BATT_ID_SETTLE_MASK, chip->batt_id_delay);
+ ret = regmap_update_bits(chip->regmap,
+ chip->base + RR_ADC_BATT_ID_CFG,
+ batt_id_delay, batt_id_delay);
+ if (ret < 0) {
+ dev_err(chip->dev,
+ "BATT_ID settling time config failed:%d\n",
+ ret);
+ goto out_disable_batt_id;
+ }
+ }
+
+ ret = regmap_update_bits(chip->regmap,
+ chip->base + RR_ADC_BATT_ID_TRIGGER,
+ RR_ADC_TRIGGER_CTL, RR_ADC_TRIGGER_CTL);
+ if (ret < 0) {
+ dev_err(chip->dev, "BATT_ID trigger set failed:%d\n", ret);
+ goto out_disable_batt_id;
+ }
+
+ ret = rradc_read_status_in_cont_mode(chip, chan_id);
+ if (ret < 0)
+ dev_err(chip->dev, "Error reading in continuous mode:%d\n",
+ ret);
+
+ /*
+ * Reset registers back to default values
+ */
+ ret = regmap_update_bits(chip->regmap,
+ chip->base + RR_ADC_BATT_ID_TRIGGER,
+ RR_ADC_TRIGGER_CTL, 0);
+ if (ret < 0)
+ dev_err(chip->dev, "BATT_ID trigger re-set failed:%d\n", ret);
+
+out_disable_batt_id:
+ ret = regmap_update_bits(chip->regmap, chip->base + RR_ADC_BATT_ID_CTRL,
+ RR_ADC_BATT_ID_CTRL_CHANNEL_CONV, 0);
+ if (ret < 0)
+ dev_err(chip->dev, "Disabling BATT ID channel failed:%d\n",
+ ret);
+
+ return ret;
+}
+
+static int rradc_do_conversion(struct rradc_chip *chip,
+ enum rradc_channel_id chan_id, u16 *data)
+{
+ const struct rradc_channel *chan = &rradc_chans[chan_id];
+ const struct iio_chan_spec *iio_chan = &rradc_iio_chans[chan_id];
+ int ret;
+ u8 buf[6];
+
+ mutex_lock(&chip->lock);
+
+ switch (chan_id) {
+ case RR_ADC_BATT_ID:
+ ret = rradc_prepare_batt_id_conversion(chip, chan_id, data);
+ if (ret < 0) {
+ dev_err(chip->dev, "Battery ID conversion failed:%d\n",
+ ret);
+ goto unlock_out;
+ }
+ break;
+
+ case RR_ADC_USBIN_V:
+ case RR_ADC_DIE_TEMP:
+ ret = rradc_read_status_in_cont_mode(chip, chan_id);
+ if (ret < 0) {
+ dev_err(chip->dev,
+ "Error reading in continuous mode:%d\n", ret);
+ goto unlock_out;
+ }
+ break;
+ case RR_ADC_CHG_HOT_TEMP:
+ case RR_ADC_CHG_TOO_HOT_TEMP:
+ case RR_ADC_SKIN_HOT_TEMP:
+ case RR_ADC_SKIN_TOO_HOT_TEMP:
+ break;
+ default:
+ if (!rradc_is_ready(chip, chan_id)) {
+ /*
+ * Usually this means the channel isn't attached, for example
+ * the in_voltage_usbin_v_input channel will not be ready if
+ * no USB cable is attached
+ */
+ dev_dbg(chip->dev, "channel '%s' is not ready\n",
+ iio_chan->datasheet_name);
+ ret = -ENODATA;
+ goto unlock_out;
+ }
+ break;
+ }
+
+ ret = rradc_read(chip, chan->lsb, buf, chan->size);
+ if (ret) {
+ dev_err(chip->dev, "read data failed\n");
+ goto unlock_out;
+ }
+
+ /*
+ * For the battery ID we read the register for every ID ADC and then
+ * see which one is actually connected.
+ */
+ if (chan_id == RR_ADC_BATT_ID) {
+ u16 batt_id_150 = get_unaligned_le16(buf + 4);
+ u16 batt_id_15 = get_unaligned_le16(buf + 2);
+ u16 batt_id_5 = get_unaligned_le16(buf);
+
+ if (!batt_id_150 && !batt_id_15 && !batt_id_5) {
+ dev_err(chip->dev,
+ "Invalid batt_id values with all zeros\n");
+ ret = -EINVAL;
+ goto unlock_out;
+ }
+
+ if (batt_id_150 <= RR_ADC_BATT_ID_RANGE) {
+ *data = batt_id_150;
+ chip->batt_id_data = 150;
+ } else if (batt_id_15 <= RR_ADC_BATT_ID_RANGE) {
+ *data = batt_id_15;
+ chip->batt_id_data = 15;
+ } else {
+ *data = batt_id_5;
+ chip->batt_id_data = 5;
+ }
+ } else {
+ /*
+ * All of the other channels are either 1 or 2 bytes.
+ * We can rely on the second byte being 0 for 1-byte channels.
+ */
+ *data = get_unaligned_le16(buf);
+ }
+
+unlock_out:
+ mutex_unlock(&chip->lock);
+
+ return ret;
+}
+
+static int rradc_read_raw(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan_spec, int *val,
+ int *val2, long mask)
+{
+ struct rradc_chip *chip = iio_priv(indio_dev);
+ const struct rradc_channel *chan;
+ int ret;
+ u16 adc_code;
+
+ if (chan_spec->address >= RR_ADC_CHAN_MAX) {
+ dev_err(chip->dev, "Invalid channel index:%ld\n",
+ chan_spec->address);
+ return -EINVAL;
+ }
+
+ chan = &rradc_chans[chan_spec->address];
+ ret = rradc_do_conversion(chip, chan_spec->address, &adc_code);
+ if (ret < 0)
+ return ret;
+
+ switch (mask) {
+ case IIO_CHAN_INFO_RAW:
+ *val = adc_code;
+ return IIO_VAL_INT;
+ case IIO_CHAN_INFO_PROCESSED:
+ chan->scale(chip, adc_code, val);
+ return IIO_VAL_INT;
+ default:
+ return -EINVAL;
+ }
+}
+
+static const struct iio_info rradc_info = {
+ .read_raw = &rradc_read_raw,
+};
+
+static const struct rradc_channel rradc_chans[RR_ADC_CHAN_MAX] = {
+ {
+ .scale = rradc_post_process_batt_id,
+ .lsb = RR_ADC_BATT_ID_5_LSB,
+ .status = RR_ADC_BATT_ID_STS,
+ .size = 6,
+ .trigger_addr = RR_ADC_BATT_ID_TRIGGER,
+ .trigger_mask = BIT(0),
+ },
+ {
+ .scale = rradc_post_process_therm,
+ .lsb = RR_ADC_BATT_THERM_LSB,
+ .status = RR_ADC_BATT_THERM_STS,
+ .size = 2,
+ .trigger_addr = RR_ADC_BATT_THERM_TRIGGER,
+ },
+ {
+ .scale = rradc_post_process_therm,
+ .lsb = RR_ADC_SKIN_TEMP_LSB,
+ .status = RR_ADC_AUX_THERM_STS,
+ .size = 2,
+ .trigger_addr = RR_ADC_AUX_THERM_TRIGGER,
+ },
+ {
+ .scale = rradc_post_process_usbin_curr,
+ .lsb = RR_ADC_USB_IN_I_LSB,
+ .status = RR_ADC_USB_IN_I_STS,
+ .size = 2,
+ .trigger_addr = RR_ADC_USB_IN_I_TRIGGER,
+ },
+ {
+ .scale = rradc_post_process_volt,
+ .lsb = RR_ADC_USB_IN_V_LSB,
+ .status = RR_ADC_USB_IN_V_STS,
+ .size = 2,
+ .trigger_addr = RR_ADC_USB_IN_V_TRIGGER,
+ .trigger_mask = BIT(7),
+ },
+ {
+ .scale = rradc_post_process_dcin_curr,
+ .lsb = RR_ADC_DC_IN_I_LSB,
+ .status = RR_ADC_DC_IN_I_STS,
+ .size = 2,
+ .trigger_addr = RR_ADC_DC_IN_I_TRIGGER,
+ },
+ {
+ .scale = rradc_post_process_volt,
+ .lsb = RR_ADC_DC_IN_V_LSB,
+ .status = RR_ADC_DC_IN_V_STS,
+ .size = 2,
+ .trigger_addr = RR_ADC_DC_IN_V_TRIGGER,
+ },
+ {
+ .scale = rradc_post_process_die_temp,
+ .lsb = RR_ADC_PMI_DIE_TEMP_LSB,
+ .status = RR_ADC_PMI_DIE_TEMP_STS,
+ .size = 2,
+ .trigger_addr = RR_ADC_PMI_DIE_TEMP_TRIGGER,
+ .trigger_mask = RR_ADC_TRIGGER_EVERY_CYCLE,
+ },
+ {
+ .scale = rradc_post_process_chg_temp,
+ .lsb = RR_ADC_CHARGER_TEMP_LSB,
+ .status = RR_ADC_CHARGER_TEMP_STS,
+ .size = 2,
+ .trigger_addr = RR_ADC_CHARGER_TEMP_TRIGGER,
+ },
+ {
+ .scale = rradc_post_process_gpio,
+ .lsb = RR_ADC_GPIO_LSB,
+ .status = RR_ADC_GPIO_STS,
+ .size = 2,
+ .trigger_addr = RR_ADC_GPIO_TRIGGER,
+ },
+ {
+ .scale = rradc_post_process_chg_temp_hot,
+ .lsb = RR_ADC_CHARGER_HOT,
+ .status = RR_ADC_CHARGER_TEMP_STS,
+ .size = 1,
+ .trigger_addr = RR_ADC_CHARGER_TEMP_TRIGGER,
+ },
+ {
+ .scale = rradc_post_process_chg_temp_hot,
+ .lsb = RR_ADC_CHARGER_TOO_HOT,
+ .status = RR_ADC_CHARGER_TEMP_STS,
+ .size = 1,
+ .trigger_addr = RR_ADC_CHARGER_TEMP_TRIGGER,
+ },
+ {
+ .scale = rradc_post_process_skin_temp_hot,
+ .lsb = RR_ADC_SKIN_HOT,
+ .status = RR_ADC_AUX_THERM_STS,
+ .size = 1,
+ .trigger_addr = RR_ADC_AUX_THERM_TRIGGER,
+ },
+ {
+ .scale = rradc_post_process_skin_temp_hot,
+ .lsb = RR_ADC_SKIN_TOO_HOT,
+ .status = RR_ADC_AUX_THERM_STS,
+ .size = 1,
+ .trigger_addr = RR_ADC_AUX_THERM_TRIGGER,
+ },
+};
+
+static const struct iio_chan_spec rradc_iio_chans[RR_ADC_CHAN_MAX] = {
+ {
+ .datasheet_name = "batt_id",
+ .type = IIO_RESISTANCE,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
+ .address = RR_ADC_BATT_ID,
+ },
+ {
+ .datasheet_name = "batt_therm",
+ .type = IIO_TEMP,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
+ .address = RR_ADC_BATT_THERM,
+ },
+ {
+ .datasheet_name = "skin_temp",
+ .type = IIO_TEMP,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED)|
+ BIT(IIO_CHAN_INFO_RAW),
+ .address = RR_ADC_SKIN_TEMP,
+ },
+ {
+ .datasheet_name = "usbin_i",
+ .type = IIO_CURRENT,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
+ .address = RR_ADC_USBIN_I,
+ },
+ {
+ .datasheet_name = "usbin_v",
+ .type = IIO_VOLTAGE,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
+ .address = RR_ADC_USBIN_V,
+ },
+ {
+ .datasheet_name = "dcin_i",
+ .type = IIO_CURRENT,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
+ .address = RR_ADC_DCIN_I,
+ },
+ {
+ .datasheet_name = "dcin_v",
+ .type = IIO_VOLTAGE,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
+ .address = RR_ADC_DCIN_V,
+ },
+ {
+ .datasheet_name = "die_temp",
+ .type = IIO_TEMP,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED)|
+ BIT(IIO_CHAN_INFO_RAW),
+ .address = RR_ADC_DIE_TEMP,
+ },
+ {
+ .datasheet_name = "chg_temp",
+ .type = IIO_TEMP,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED)|
+ BIT(IIO_CHAN_INFO_RAW),
+ .address = RR_ADC_CHG_TEMP,
+ },
+ {
+ .datasheet_name = "gpio",
+ .type = IIO_VOLTAGE,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED)|
+ BIT(IIO_CHAN_INFO_RAW),
+ .address = RR_ADC_GPIO,
+ },
+ {
+ .datasheet_name = "chg_temp_hot",
+ .type = IIO_TEMP,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED)|
+ BIT(IIO_CHAN_INFO_RAW),
+ .address = RR_ADC_CHG_HOT_TEMP,
+ },
+ {
+ .datasheet_name = "chg_temp_too_hot",
+ .type = IIO_TEMP,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED)|
+ BIT(IIO_CHAN_INFO_RAW),
+ .address = RR_ADC_CHG_TOO_HOT_TEMP,
+ },
+ {
+ .datasheet_name = "skin_temp_hot",
+ .type = IIO_TEMP,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED)|
+ BIT(IIO_CHAN_INFO_RAW),
+ .address = RR_ADC_SKIN_TEMP,
+ },
+ {
+ .datasheet_name = "skin_temp_too_hot",
+ .type = IIO_TEMP,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED)|
+ BIT(IIO_CHAN_INFO_RAW),
+ .address = RR_ADC_SKIN_TEMP,
+ },
+};
+
+static int rradc_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct iio_dev *indio_dev;
+ struct rradc_chip *chip;
+ int ret, i;
+
+ indio_dev = devm_iio_device_alloc(dev, sizeof(*chip));
+ if (!indio_dev)
+ return -ENOMEM;
+
+ chip = iio_priv(indio_dev);
+ chip->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+ if (!chip->regmap) {
+ dev_err(dev, "Couldn't get parent's regmap\n");
+ return -EINVAL;
+ }
+
+ chip->dev = dev;
+ mutex_init(&chip->lock);
+
+ ret = device_property_read_u32(dev, "reg", &chip->base);
+ if (ret < 0) {
+ dev_err(chip->dev, "Couldn't find reg address, ret = %d\n",
+ ret);
+ return ret;
+ }
+
+ chip->batt_id_delay = -EINVAL;
+ ret = device_property_read_u32(dev, "qcom,batt-id-delay-ms",
+ &chip->batt_id_delay);
+ if (!ret) {
+ for (i = 0; i < RRADC_BATT_ID_DELAY_MAX; i++) {
+ if (chip->batt_id_delay == batt_id_delays[i])
+ break;
+ }
+ if (i == RRADC_BATT_ID_DELAY_MAX)
+ chip->batt_id_delay = -EINVAL;
+ }
+
+ /* Get the PMIC revision ID, we need to handle some varying coefficients */
+ chip->pmic = (struct qcom_spmi_pmic *)spmi_device_get_drvdata(
+ to_spmi_device(pdev->dev.parent));
+ qcom_pmic_print_info(chip->dev, chip->pmic);
+
+ indio_dev->name = pdev->name;
+ indio_dev->modes = INDIO_DIRECT_MODE;
+ indio_dev->info = &rradc_info;
+ indio_dev->channels = rradc_iio_chans;
+ indio_dev->num_channels = RR_ADC_CHAN_MAX;
+
+ return devm_iio_device_register(dev, indio_dev);
+}
+
+static const struct of_device_id rradc_match_table[] = {
+ { .compatible = "qcom,pm660-rradc" },
+ { .compatible = "qcom,pmi8998-rradc" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, rradc_match_table);
+
+static struct platform_driver rradc_driver = {
+ .driver = {
+ .name = "qcom-rradc",
+ .of_match_table = rradc_match_table,
+ },
+ .probe = rradc_probe,
+};
+module_platform_driver(rradc_driver);
+
+MODULE_DESCRIPTION("QCOM SPMI PMIC RR ADC driver");
+MODULE_AUTHOR("Caleb Connolly <[email protected]>");
+MODULE_LICENSE("GPL v2");
--
2.34.1
Add a DT node for the Round Robin ADC found in the PMI8998 PMIC.
Signed-off-by: Caleb Connolly <[email protected]>
---
arch/arm64/boot/dts/qcom/pmi8998.dtsi | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/pmi8998.dtsi b/arch/arm64/boot/dts/qcom/pmi8998.dtsi
index 0fef5f113f05..da10668c361d 100644
--- a/arch/arm64/boot/dts/qcom/pmi8998.dtsi
+++ b/arch/arm64/boot/dts/qcom/pmi8998.dtsi
@@ -18,6 +18,14 @@ pmi8998_gpio: gpios@c000 {
interrupt-controller;
#interrupt-cells = <2>;
};
+
+ pmi8998_rradc: rradc@4500 {
+ compatible = "qcom,pmi8998-rradc";
+ reg = <0x4500>;
+ #io-channel-cells = <1>;
+
+ status = "disabled";
+ };
};
pmi8998_lsid1: pmic@3 {
--
2.34.1
Hi Caleb,
Thank you for the patch! Yet something to improve:
[auto build test ERROR on robh/for-next]
[also build test ERROR on jic23-iio/togreg lee-mfd/for-mfd-next v5.16-rc8 next-20220105]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]
url: https://github.com/0day-ci/linux/commits/Caleb-Connolly/iio-adc-introduce-Qualcomm-SPMI-Round-Robin-ADC/20220106-023716
base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next
config: sh-allmodconfig (https://download.01.org/0day-ci/archive/20220106/[email protected]/config)
compiler: sh4-linux-gcc (GCC) 11.2.0
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# https://github.com/0day-ci/linux/commit/167368793a009e8c1ce75b0b8b0965a4574af527
git remote add linux-review https://github.com/0day-ci/linux
git fetch --no-tags linux-review Caleb-Connolly/iio-adc-introduce-Qualcomm-SPMI-Round-Robin-ADC/20220106-023716
git checkout 167368793a009e8c1ce75b0b8b0965a4574af527
# save the config file to linux build tree
mkdir build_dir
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-11.2.0 make.cross O=build_dir ARCH=sh SHELL=/bin/bash drivers/iio/adc/
If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <[email protected]>
All errors (new ones prefixed by >>):
drivers/iio/adc/qcom-spmi-rradc.c: In function 'rradc_prepare_batt_id_conversion':
>> drivers/iio/adc/qcom-spmi-rradc.c:624:25: error: implicit declaration of function 'FIELD_PREP' [-Werror=implicit-function-declaration]
624 | FIELD_PREP(BATT_ID_SETTLE_MASK, chip->batt_id_delay);
| ^~~~~~~~~~
cc1: some warnings being treated as errors
vim +/FIELD_PREP +624 drivers/iio/adc/qcom-spmi-rradc.c
607
608 static int rradc_prepare_batt_id_conversion(struct rradc_chip *chip,
609 enum rradc_channel_id chan_id,
610 u16 *data)
611 {
612 int ret, batt_id_delay;
613
614 ret = regmap_update_bits(chip->regmap, chip->base + RR_ADC_BATT_ID_CTRL,
615 RR_ADC_BATT_ID_CTRL_CHANNEL_CONV,
616 RR_ADC_BATT_ID_CTRL_CHANNEL_CONV);
617 if (ret < 0) {
618 dev_err(chip->dev, "Enabling BATT ID channel failed:%d\n", ret);
619 return ret;
620 }
621
622 if (chip->batt_id_delay != -EINVAL) {
623 batt_id_delay =
> 624 FIELD_PREP(BATT_ID_SETTLE_MASK, chip->batt_id_delay);
625 ret = regmap_update_bits(chip->regmap,
626 chip->base + RR_ADC_BATT_ID_CFG,
627 batt_id_delay, batt_id_delay);
628 if (ret < 0) {
629 dev_err(chip->dev,
630 "BATT_ID settling time config failed:%d\n",
631 ret);
632 goto out_disable_batt_id;
633 }
634 }
635
636 ret = regmap_update_bits(chip->regmap,
637 chip->base + RR_ADC_BATT_ID_TRIGGER,
638 RR_ADC_TRIGGER_CTL, RR_ADC_TRIGGER_CTL);
639 if (ret < 0) {
640 dev_err(chip->dev, "BATT_ID trigger set failed:%d\n", ret);
641 goto out_disable_batt_id;
642 }
643
644 ret = rradc_read_status_in_cont_mode(chip, chan_id);
645 if (ret < 0)
646 dev_err(chip->dev, "Error reading in continuous mode:%d\n",
647 ret);
648
649 /*
650 * Reset registers back to default values
651 */
652 ret = regmap_update_bits(chip->regmap,
653 chip->base + RR_ADC_BATT_ID_TRIGGER,
654 RR_ADC_TRIGGER_CTL, 0);
655 if (ret < 0)
656 dev_err(chip->dev, "BATT_ID trigger re-set failed:%d\n", ret);
657
658 out_disable_batt_id:
659 ret = regmap_update_bits(chip->regmap, chip->base + RR_ADC_BATT_ID_CTRL,
660 RR_ADC_BATT_ID_CTRL_CHANNEL_CONV, 0);
661 if (ret < 0)
662 dev_err(chip->dev, "Disabling BATT ID channel failed:%d\n",
663 ret);
664
665 return ret;
666 }
667
---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/[email protected]