Samsung's tablet Galaxy Tab S 10.5" (wifi) has codename Chagall WiFi
and is one of several tablets released in 2014 based on Exynos 5420.
This initial devicetree adds support for accessing device over USB or
UART, and allows using a rootfs in either the internal eMMC or an
external sdcard. 4 out of 8 CPUs are brought up when device boots,
which is the same as on the somewhat similar board
exynos5420-arndale-octa.
Patch 2 is necessary after a secure-firmware node is added, otherwise
device hangs during the CPU1BOOT secure monitor call. Without the
secure-firmware node we are not able to bring up any secondary CPUs.
Changes since v3:
=================
* Rename device specific regulators LDOx -> VDD_LDOx for consistency
* Make LDO32 vary with device and add on/off-in-suspend to a couple
of more regulators, to match vendor kernel
* Fix mmc2 card-detect, with cd-gpios defined and pin config
pin-pud=pin_pull_none sdcard insertion is detected and seen in dmesg
* Rename sd2-cd-pins -> mmc2-cd-pins
Changes since v2
================
Addressing Krzysztof's feedback:
* chagallwifi -> chagall-wifi and Chagall WiFi in messages and comments
* Re-write commit message for patch 3, use commit hash and ("subject"),
move hint about bootloader issue to galaxy-tab-common.dtsi
* Fix s2mps11 regulator nodes, use &ldoXX_reg handle for device customisation
* Re-add usbdrd supplies (works after fixing regulator nodes)
* Remove unnecessary, duplicate, compatible in galaxy-tab-common.dtsi
* Remove extra clocks xxti and xusbxti
* Prefix key- to gpio-keys
* Add pinctrl pins to mmc_2. card-detect pin is different than for other
Exynos 5420 devices, so define and use mmc2_cd node under pinctrl_0
Additional changes:
* Add/fix supplies of mmc_0 and mmc_2 (vmmc-supply for mmc0 is unknown)
* Sort mmc_X properties alphabetically
* Fix IRQ pin for s2mps11, it was wrong (gpx3-2 -> gpx3-0)
* Mark LDO31 as varying between devices as well, it differs between WiFi
and LTE tablet versions
* Fix typo for LDO5 (regulato-name -> regulator-name)
* Remove regulator-ramp-delay from buck regulators, based on
exynos5420-arndale-octa there should be no need to set it
Changes since v1
================
Fix mmc_0 and usbdrd in patch 3:
* Remove extra, non supported, options from mmc_0 node
* Do not set usbdrd supplies. Usb networking does not work with them
specified, but it works fine with dummy regulators
Henrik Grimler (3):
dt-bindings: arm: samsung: document Chagall WiFi board binding
ARM: exynos: only do SMC_CMD_CPU1BOOT call on Exynos4
ARM: dts: Add support for Samsung Chagall WiFi
.../bindings/arm/samsung/samsung-boards.yaml | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/exynos5420-chagall-wifi.dts | 75 ++
.../dts/exynos5420-galaxy-tab-common.dtsi | 692 ++++++++++++++++++
arch/arm/mach-exynos/firmware.c | 4 +-
5 files changed, 772 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/exynos5420-chagall-wifi.dts
create mode 100644 arch/arm/boot/dts/exynos5420-galaxy-tab-common.dtsi
--
2.34.1
Add binding for Samsung Galaxy Tab S 10.5", based on Exynos 5420 with
codename chagall-wifi. It was released in 2014 and has several siblings
with similar hardware.
Signed-off-by: Henrik Grimler <[email protected]>
---
.../devicetree/bindings/arm/samsung/samsung-boards.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.yaml b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.yaml
index 052cd94113d4..a2a8bf44fe9b 100644
--- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.yaml
+++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.yaml
@@ -140,6 +140,7 @@ properties:
items:
- enum:
- insignal,arndale-octa # Insignal Arndale Octa
+ - samsung,chagall-wifi # Samsung SM-T800
- samsung,smdk5420 # Samsung SMDK5420 eval
- const: samsung,exynos5420
- const: samsung,exynos5
--
2.34.1
On Exynos5 the call is simply ignored by most variants of the
trustzone firmware. However, on some devices it instead causes the
device to hang, so let's avoid the call for the SoCs where it should
not be needed.
To see that the call is ignored, we can look into sboot/tzsw. On most
of the Exynos{4,5} devices the part of sboot/tzsw that seem to handle
the secure monitor calls is quite easy to recognise, the SMC number is
compared to known ones, and if equal it branches to the relevant
function. In assembly this looks something like:
;-- handle_smc:
0x00000514 650070e3 cmn r0, 0x65
0x00000518 0a00000a beq loc.smc_cmd_reg
0x0000051c 010070e3 cmn r0, 1
0x00000520 6c00000a beq loc.smc_cmd_init
0x00000524 020070e3 cmn r0, 2
0x00000528 6b00000a beq loc.smc_cmd_info
0x0000052c 030070e3 cmn r0, 3
0x00000530 6e00000a beq loc.smc_cmd_sleep
0x00000534 060070e3 cmn r0, 6
0x00000538 ae00000a beq loc.smc_cmd_save_state
0x0000053c 070070e3 cmn r0, 7
0x00000540 b400000a beq loc.smc_cmd_standby
0x00000544 2b01001a bne loc.smc_return_minus1
where above example is from exynos5420-arndale-octa. As can be seen
the case where r0 is 4 (i.e. SMC_CMD_CPU1BOOT) is not handled. The
annotations are taken from github.com/hsnaves/exynos5410-firmware,
where a large part of the exynos5410 trustzone firmware has been
reverse-engineered.
Signed-off-by: Henrik Grimler <[email protected]>
Tested-by: Marek Szyprowski <[email protected]>
---
Sent previously as RFC
---
arch/arm/mach-exynos/firmware.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/arch/arm/mach-exynos/firmware.c b/arch/arm/mach-exynos/firmware.c
index 2eaf2dbb8e81..2da5b60b59e2 100644
--- a/arch/arm/mach-exynos/firmware.c
+++ b/arch/arm/mach-exynos/firmware.c
@@ -60,8 +60,10 @@ static int exynos_cpu_boot(int cpu)
/*
* Exynos3250 doesn't need to send smc command for secondary CPU boot
* because Exynos3250 removes WFE in secure mode.
+ *
+ * On Exynos5 devices the call is ignored by trustzone firmware.
*/
- if (soc_is_exynos3250())
+ if (!soc_is_exynos4210() && !soc_is_exynos4412())
return 0;
/*
--
2.34.1
Chagall WiFi, with product name Samsung Galaxy Tab S 10.5", is based
on Exynos 5420. This device is one of several tablet models released
in 2014 based on Exynos 5420.
The device tree added here contains support for:
- UART
- eMMC
- SD card
- USB
CCI has been disabled in the hardware, enabling it would require
(de-)soldering a resistor on the board. Trying to boot with it
enabled in kernel makes the device hang when CCI is probed.
Exynos5420-arndale-octa also has had CCI disabled due to issues, see
commit 25217fef3551 ("ARM: dts: disable CCI on exynos5420 based
arndale-octa").
Signed-off-by: Henrik Grimler <[email protected]>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/exynos5420-chagall-wifi.dts | 75 ++
.../dts/exynos5420-galaxy-tab-common.dtsi | 692 ++++++++++++++++++
3 files changed, 768 insertions(+)
create mode 100644 arch/arm/boot/dts/exynos5420-chagall-wifi.dts
create mode 100644 arch/arm/boot/dts/exynos5420-galaxy-tab-common.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 0de64f237cd8..088fcedb3212 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -220,6 +220,7 @@ dtb-$(CONFIG_ARCH_EXYNOS5) += \
exynos5420-arndale-octa.dtb \
exynos5420-peach-pit.dtb \
exynos5420-smdk5420.dtb \
+ exynos5420-chagall-wifi.dtb \
exynos5422-odroidhc1.dtb \
exynos5422-odroidxu3.dtb \
exynos5422-odroidxu3-lite.dtb \
diff --git a/arch/arm/boot/dts/exynos5420-chagall-wifi.dts b/arch/arm/boot/dts/exynos5420-chagall-wifi.dts
new file mode 100644
index 000000000000..1319344a2c74
--- /dev/null
+++ b/arch/arm/boot/dts/exynos5420-chagall-wifi.dts
@@ -0,0 +1,75 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's Exynos5420 Chagall WiFi board device tree source
+ *
+ * Copyright (c) 2012-2013 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ * Copyright (c) 2022 Henrik Grimler
+ */
+
+/dts-v1/;
+#include "exynos5420-galaxy-tab-common.dtsi"
+
+/ {
+ model = "Samsung Chagall WiFi based on Exynos5420";
+ compatible = "samsung,chagall-wifi", "samsung,exynos5420", \
+ "samsung,exynos5";
+};
+
+&ldo15_reg {
+ /* Unused */
+ regulator-name = "VDD_LDO15";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+};
+
+&ldo17_reg {
+ regulator-name = "VDD_IRLED_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3350000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+};
+
+&ldo28_reg {
+ /* Unused */
+ regulator-name = "VDD_LDO28";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+};
+
+&ldo29_reg {
+ regulator-name = "VDD_TCON_1V8";
+ regulator-min-microvolt = <1900000>;
+ regulator-max-microvolt = <1900000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+};
+
+&ldo31_reg {
+ regulator-name = "VDD_GRIP_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+};
+
+&ldo32_reg {
+ regulator-name = "VDD_TSP_1V8";
+ regulator-min-microvolt = <1900000>;
+ regulator-max-microvolt = <1900000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+};
diff --git a/arch/arm/boot/dts/exynos5420-galaxy-tab-common.dtsi b/arch/arm/boot/dts/exynos5420-galaxy-tab-common.dtsi
new file mode 100644
index 000000000000..e4ed0fd153f4
--- /dev/null
+++ b/arch/arm/boot/dts/exynos5420-galaxy-tab-common.dtsi
@@ -0,0 +1,692 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Base DT for Samsung's family of tablets based on Exynos5420.
+ *
+ * Copyright (c) 2012-2013 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ * Copyright (c) 2022 Henrik Grimler
+ */
+
+/dts-v1/;
+#include "exynos5420.dtsi"
+#include "exynos5420-cpus.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/samsung,s2mps11.h>
+
+/ {
+ chassis-type = "tablet";
+
+ /*
+ * To successfully boot the mainline kernel with the stock
+ * bootloader (SBOOT), the tlb needs to be flushed after the
+ * page table pointer has been updated in __common_mmu_cache_on.
+ * The same hack is also needed to boot exynos4412-i9300 with
+ * stock bootloader, and probably other Samsung devices of
+ * similar age. See
+ * https://lore.kernel.org/all/[email protected]
+ * for more details.
+ */
+
+ chosen {
+ stdout-path = "serial2:115200n8";
+ };
+
+ memory@20000000 {
+ device_type = "memory";
+ reg = <0x20000000 0xc0000000>;
+ };
+
+ firmware@2073000 {
+ compatible = "samsung,secure-firmware";
+ reg = <0x02073000 0x1000>;
+ };
+
+ fixed-rate-clocks {
+ oscclk {
+ compatible = "samsung,exynos5420-oscclk";
+ clock-frequency = <24000000>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+
+ key-power {
+ debounce-interval = <10>;
+ gpios = <&gpx2 2 GPIO_ACTIVE_LOW>;
+ label = "Power";
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+
+ key-home {
+ debounce-interval = <10>;
+ gpios = <&gpx0 5 GPIO_ACTIVE_LOW>;
+ label = "Home";
+ linux,code = <KEY_HOME>;
+ wakeup-source;
+ };
+
+ key-volume-up {
+ debounce-interval = <10>;
+ gpios = <&gpx0 2 GPIO_ACTIVE_LOW>;
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ };
+
+ key-volume-down {
+ debounce-interval = <10>;
+ gpios = <&gpx0 3 GPIO_ACTIVE_LOW>;
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+ };
+};
+
+&cci {
+ /* CCI is disabled in hardware */
+ status = "disabled";
+};
+
+&cpu0 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&cpu4 {
+ cpu-supply = <&buck6_reg>;
+};
+
+&gpu {
+ status = "okay";
+ mali-supply = <&buck4_reg>;
+};
+
+&hsi2c_7 {
+ status = "okay";
+
+ pmic@66 {
+ compatible = "samsung,s2mps11-pmic";
+ reg = <0x66>;
+
+ interrupt-parent = <&gpx3>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&s2mps11_irq>;
+
+ s2mps11_osc: clocks {
+ compatible = "samsung,s2mps11-clk";
+ #clock-cells = <1>;
+ clock-output-names = "s2mps11_ap", "s2mps11_cp",
+ "s2mps11_bt";
+ };
+
+ regulators {
+ buck1_reg: BUCK1 {
+ regulator-name = "VDD_MIF_1V1";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "VDD_ARM_1V0";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "VDD_INT_1V0";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ buck4_reg: BUCK4 {
+ regulator-name = "VDD_G3D_1V0";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ buck5_reg: BUCK5 {
+ regulator-name = "VDD_MEM_1V2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+
+ };
+
+ buck6_reg: BUCK6 {
+ regulator-name = "VDD_KFC_1V0";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ buck7_reg: BUCK7 {
+ regulator-name = "VIN_LLDO_1V4";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ };
+
+ buck8_reg: BUCK8 {
+ regulator-name = "VIN_MLDO_2V0";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2100000>;
+ regulator-always-on;
+ };
+
+ buck9_reg: BUCK9 {
+ regulator-name = "VIN_HLDO_3V5";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3500000>;
+ regulator-always-on;
+ };
+
+ buck10_reg: BUCK10 {
+ regulator-name = "VDD_CAM_ISP_1V0";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <3550000>;
+ };
+
+ ldo1_reg: LDO1 {
+ regulator-name = "VDD_ALIVE_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "VDD_APIO_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "VDD_APIO_MMC01_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "VDD_ADC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ ldo5_reg: LDO5 {
+ /* Unused */
+ regulator-name = "VDD_LDO5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "VDD_MIPI_1V0";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo7_reg: LDO7 {
+ regulator-name = "VDD_MIPI_PLL_ABB1_18V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo8_reg: LDO8 {
+ /* Unused */
+ regulator-name = "VDD_LDO8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo9_reg: LDO9 {
+ regulator-name = "VDD_UOTG_3V0";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ ldo10_reg: LDO10 {
+ regulator-name = "VDDQ_PRE_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ ldo11_reg: LDO11 {
+ regulator-name = "VDD_HSIC_1V0";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ ldo12_reg: LDO12 {
+ regulator-name = "VDD_HSIC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ ldo13_reg: LDO13 {
+ regulator-name = "VDD_APIO_MMC2_2V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo14_reg: LDO14 {
+ regulator-name = "VDD_MOTOR_3V0";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo15_reg: LDO15 {
+ regulator-name = "VDD_LDO15";
+ /*
+ * LDO15 varies between devices and is
+ * specified in the device dts
+ */
+ };
+
+ ldo16_reg: LDO16 {
+ regulator-name = "VDD_AP_2V8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ ldo17_reg: LDO17 {
+ regulator-name = "VDD_LDO17";
+ /*
+ * LDO17 varies between devices and is
+ * specified in the device dts
+ */
+ };
+
+ ldo18_reg: LDO18 {
+ /* Unused */
+ regulator-name = "VDD_LDO18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+
+ ldo19_reg: LDO19 {
+ regulator-name = "VDD_VTF_2V8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo20_reg: LDO20 {
+ regulator-name = "VDD_CAM1_CAM_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo21_reg: LDO21 {
+ regulator-name = "VDD_CAM_IO_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo22_reg: LDO22 {
+ regulator-name = "VDD_CAM0_S_CORE_1V1";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1200000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo23_reg: LDO23 {
+ regulator-name = "VDD_MIFS_1V1";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ ldo24_reg: LDO24 {
+ regulator-name = "VDD_TSP_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo25_reg: LDO25 {
+ /* Unused */
+ regulator-name = "VDD_LDO25";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3950000>;
+ };
+
+ ldo26_reg: LDO26 {
+ regulator-name = "VDD_CAM0_AF_2V8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo27_reg: LDO27 {
+ regulator-name = "VDD_G3DS_1V0";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ ldo28_reg: LDO28 {
+ regulator-name = "VDD_LDO28";
+ /*
+ * LDO28 varies between devices and is
+ * specified in the device dts
+ */
+ };
+
+ ldo29_reg: LDO29 {
+ regulator-name = "VDD_LDO29";
+ /*
+ * LDO29 varies between devices and is
+ * specified in the device dts
+ */
+ };
+
+ ldo30_reg: LDO30 {
+ regulator-name = "VDD_TOUCH_1V8";
+ regulator-min-microvolt = <1900000>;
+ regulator-max-microvolt = <1900000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo31_reg: LDO31 {
+ regulator-name = "VDD_LDO31";
+ /*
+ * LDO31 varies between devices and is
+ * specified in the device dts
+ */
+ };
+
+ ldo32_reg: LDO32 {
+ regulator-name = "VDD_LDO32";
+ /*
+ * LDO32 varies between devices and is
+ * specified in the device dts
+ */
+ };
+
+ ldo33_reg: LDO33 {
+ regulator-name = "VDD_MHL_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo34_reg: LDO34 {
+ regulator-name = "VDD_MHL_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo35_reg: LDO35 {
+ regulator-name = "VDD_SIL_1V2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo36_reg: LDO36 {
+ /* Unused */
+ regulator-name = "VDD_LDO36";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3950000>;
+ };
+
+ ldo37_reg: LDO37 {
+ /* Unused */
+ regulator-name = "VDD_LDO37";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3950000>;
+ };
+
+ ldo38_reg: LDO38 {
+ regulator-name = "VDD_KEY_LED_3V3";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&mixer {
+ status = "okay";
+};
+
+/* Internal storage */
+&mmc_0 {
+ status = "okay";
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ card-detect-delay = <200>;
+ mmc-hs200-1_8v;
+ non-removable;
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>;
+ pinctrl-names = "default";
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-ddr-timing = <0 2>;
+ samsung,dw-mshc-sdr-timing = <0 4>;
+ vqmmc-supply = <&ldo3_reg>;
+};
+
+/* External sdcard */
+&mmc_2 {
+ status = "okay";
+ bus-width = <4>;
+ cap-sd-highspeed;
+ card-detect-delay = <200>;
+ cd-gpios = <&gpx2 4 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&sd2_clk &sd2_cmd &mmc2_cd &sd2_bus1 &sd2_bus4>;
+ pinctrl-names = "default";
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-ddr-timing = <0 2>;
+ samsung,dw-mshc-sdr-timing = <0 4>;
+ sd-uhs-sdr50;
+ vmmc-supply = <&ldo19_reg>;
+ vqmmc-supply = <&ldo13_reg>;
+};
+
+&pinctrl_0 {
+ mmc2_cd: mmc2-cd-pins {
+ samsung,pins = "gpx2-4";
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ };
+
+ s2mps11_irq: s2mps11-irq-pins {
+ samsung,pins = "gpx3-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+ };
+};
+
+&rtc {
+ status = "okay";
+ clocks = <&clock CLK_RTC>, <&s2mps11_osc S2MPS11_CLK_AP>;
+ clock-names = "rtc", "rtc_src";
+};
+
+&tmu_cpu0 {
+ vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_cpu1 {
+ vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_cpu2 {
+ vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_cpu3 {
+ vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_gpu {
+ vtmu-supply = <&ldo10_reg>;
+};
+
+&usbdrd_dwc3_0 {
+ dr_mode = "peripheral";
+};
+
+&usbdrd_dwc3_1 {
+ dr_mode = "peripheral";
+};
+
+&usbdrd3_0 {
+ vdd33-supply = <&ldo9_reg>;
+ vdd10-supply = <&ldo11_reg>;
+};
+
+&usbdrd3_1 {
+ vdd33-supply = <&ldo9_reg>;
+ vdd10-supply = <&ldo11_reg>;
+};
--
2.34.1
Hi Henrik,
>-----Original Message-----
>From: Henrik Grimler [mailto:[email protected]]
>Sent: Wednesday, January 19, 2022 12:28 AM
>To: [email protected]; [email protected];
>[email protected]; [email protected];
>[email protected]; [email protected];
>[email protected]; [email protected];
>[email protected]; [email protected]; linux-arm-
>[email protected]; [email protected];
>~postmarketos/[email protected]
>Cc: Henrik Grimler <[email protected]>
>Subject: [PATCH v4 3/3] ARM: dts: Add support for Samsung Chagall WiFi
>
>Chagall WiFi, with product name Samsung Galaxy Tab S 10.5", is based on
>Exynos 5420. This device is one of several tablet models released in 2014
>based on Exynos 5420.
>
>The device tree added here contains support for:
>
>- UART
>- eMMC
>- SD card
>- USB
>
>CCI has been disabled in the hardware, enabling it would require (de-
>)soldering a resistor on the board. Trying to boot with it enabled in
kernel
>makes the device hang when CCI is probed.
>Exynos5420-arndale-octa also has had CCI disabled due to issues, see commit
>25217fef3551 ("ARM: dts: disable CCI on exynos5420 based arndale-octa").
>
>Signed-off-by: Henrik Grimler <[email protected]>
>---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/exynos5420-chagall-wifi.dts | 75 ++
> .../dts/exynos5420-galaxy-tab-common.dtsi | 692 ++++++++++++++++++
> 3 files changed, 768 insertions(+)
> create mode 100644 arch/arm/boot/dts/exynos5420-chagall-wifi.dts
> create mode 100644 arch/arm/boot/dts/exynos5420-galaxy-tab-common.dtsi
>
>diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index
>0de64f237cd8..088fcedb3212 100644
>--- a/arch/arm/boot/dts/Makefile
>+++ b/arch/arm/boot/dts/Makefile
>@@ -220,6 +220,7 @@ dtb-$(CONFIG_ARCH_EXYNOS5) += \
> exynos5420-arndale-octa.dtb \
> exynos5420-peach-pit.dtb \
> exynos5420-smdk5420.dtb \
>+ exynos5420-chagall-wifi.dtb \
> exynos5422-odroidhc1.dtb \
> exynos5422-odroidxu3.dtb \
> exynos5422-odroidxu3-lite.dtb \
>diff --git a/arch/arm/boot/dts/exynos5420-chagall-wifi.dts
>b/arch/arm/boot/dts/exynos5420-chagall-wifi.dts
>new file mode 100644
>index 000000000000..1319344a2c74
>--- /dev/null
>+++ b/arch/arm/boot/dts/exynos5420-chagall-wifi.dts
>@@ -0,0 +1,75 @@
>+// SPDX-License-Identifier: GPL-2.0
>+/*
>+ * Samsung's Exynos5420 Chagall WiFi board device tree source
>+ *
>+ * Copyright (c) 2012-2013 Samsung Electronics Co., Ltd.
>+ * http://www.samsung.com
>+ * Copyright (c) 2022 Henrik Grimler
>+ */
>+
>+/dts-v1/;
>+#include "exynos5420-galaxy-tab-common.dtsi"
>+
>+/ {
>+ model = "Samsung Chagall WiFi based on Exynos5420";
>+ compatible = "samsung,chagall-wifi", "samsung,exynos5420", \
>+ "samsung,exynos5";
>+};
>+
>+&ldo15_reg {
>+ /* Unused */
>+ regulator-name = "VDD_LDO15";
>+ regulator-min-microvolt = <3300000>;
>+ regulator-max-microvolt = <3300000>;
>+};
>+
>+&ldo17_reg {
>+ regulator-name = "VDD_IRLED_3V3";
>+ regulator-min-microvolt = <3300000>;
>+ regulator-max-microvolt = <3350000>;
>+ regulator-always-on;
>+ regulator-boot-on;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+};
>+
>+&ldo28_reg {
>+ /* Unused */
>+ regulator-name = "VDD_LDO28";
>+ regulator-min-microvolt = <3300000>;
>+ regulator-max-microvolt = <3300000>;
>+};
>+
>+&ldo29_reg {
>+ regulator-name = "VDD_TCON_1V8";
>+ regulator-min-microvolt = <1900000>;
>+ regulator-max-microvolt = <1900000>;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+};
>+
>+&ldo31_reg {
>+ regulator-name = "VDD_GRIP_1V8";
>+ regulator-min-microvolt = <1800000>;
>+ regulator-max-microvolt = <1800000>;
>+ regulator-always-on;
>+ regulator-boot-on;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+};
>+
>+&ldo32_reg {
>+ regulator-name = "VDD_TSP_1V8";
>+ regulator-min-microvolt = <1900000>;
>+ regulator-max-microvolt = <1900000>;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+};
>diff --git a/arch/arm/boot/dts/exynos5420-galaxy-tab-common.dtsi
>b/arch/arm/boot/dts/exynos5420-galaxy-tab-common.dtsi
>new file mode 100644
>index 000000000000..e4ed0fd153f4
>--- /dev/null
>+++ b/arch/arm/boot/dts/exynos5420-galaxy-tab-common.dtsi
>@@ -0,0 +1,692 @@
>+// SPDX-License-Identifier: GPL-2.0
>+/*
>+ * Base DT for Samsung's family of tablets based on Exynos5420.
>+ *
>+ * Copyright (c) 2012-2013 Samsung Electronics Co., Ltd.
>+ * http://www.samsung.com
>+ * Copyright (c) 2022 Henrik Grimler
>+ */
>+
>+/dts-v1/;
>+#include "exynos5420.dtsi"
>+#include "exynos5420-cpus.dtsi"
>+#include <dt-bindings/input/input.h>
>+#include <dt-bindings/gpio/gpio.h>
>+#include <dt-bindings/clock/samsung,s2mps11.h>
>+
>+/ {
>+ chassis-type = "tablet";
>+
>+ /*
>+ * To successfully boot the mainline kernel with the stock
>+ * bootloader (SBOOT), the tlb needs to be flushed after the
>+ * page table pointer has been updated in
>__common_mmu_cache_on.
>+ * The same hack is also needed to boot exynos4412-i9300 with
>+ * stock bootloader, and probably other Samsung devices of
>+ * similar age. See
>+ * https://lore.kernel.org/all/1355276466-18295-1-git-send-email-
>[email protected]
>+ * for more details.
>+ */
>+
>+ chosen {
>+ stdout-path = "serial2:115200n8";
>+ };
>+
>+ memory@20000000 {
>+ device_type = "memory";
>+ reg = <0x20000000 0xc0000000>;
>+ };
>+
>+ firmware@2073000 {
>+ compatible = "samsung,secure-firmware";
>+ reg = <0x02073000 0x1000>;
>+ };
>+
>+ fixed-rate-clocks {
>+ oscclk {
>+ compatible = "samsung,exynos5420-oscclk";
>+ clock-frequency = <24000000>;
>+ };
>+ };
>+
>+ gpio-keys {
>+ compatible = "gpio-keys";
>+ pinctrl-names = "default";
>+
>+ key-power {
>+ debounce-interval = <10>;
>+ gpios = <&gpx2 2 GPIO_ACTIVE_LOW>;
>+ label = "Power";
>+ linux,code = <KEY_POWER>;
>+ wakeup-source;
>+ };
>+
>+ key-home {
>+ debounce-interval = <10>;
>+ gpios = <&gpx0 5 GPIO_ACTIVE_LOW>;
>+ label = "Home";
>+ linux,code = <KEY_HOME>;
>+ wakeup-source;
>+ };
>+
>+ key-volume-up {
>+ debounce-interval = <10>;
>+ gpios = <&gpx0 2 GPIO_ACTIVE_LOW>;
>+ label = "Volume Up";
>+ linux,code = <KEY_VOLUMEUP>;
>+ };
>+
>+ key-volume-down {
>+ debounce-interval = <10>;
>+ gpios = <&gpx0 3 GPIO_ACTIVE_LOW>;
>+ label = "Volume Down";
>+ linux,code = <KEY_VOLUMEDOWN>;
>+ };
>+ };
>+};
>+
>+&cci {
>+ /* CCI is disabled in hardware */
>+ status = "disabled";
>+};
>+
>+&cpu0 {
>+ cpu-supply = <&buck2_reg>;
>+};
>+
>+&cpu4 {
>+ cpu-supply = <&buck6_reg>;
>+};
>+
>+&gpu {
>+ status = "okay";
>+ mali-supply = <&buck4_reg>;
>+};
>+
>+&hsi2c_7 {
>+ status = "okay";
>+
>+ pmic@66 {
>+ compatible = "samsung,s2mps11-pmic";
>+ reg = <0x66>;
>+
>+ interrupt-parent = <&gpx3>;
>+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
>+ pinctrl-names = "default";
>+ pinctrl-0 = <&s2mps11_irq>;
>+
>+ s2mps11_osc: clocks {
>+ compatible = "samsung,s2mps11-clk";
>+ #clock-cells = <1>;
>+ clock-output-names = "s2mps11_ap", "s2mps11_cp",
>+ "s2mps11_bt";
>+ };
>+
>+ regulators {
>+ buck1_reg: BUCK1 {
>+ regulator-name = "VDD_MIF_1V1";
>+ regulator-min-microvolt = <700000>;
>+ regulator-max-microvolt = <1300000>;
>+ regulator-always-on;
>+ regulator-boot-on;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+ };
>+
>+ buck2_reg: BUCK2 {
>+ regulator-name = "VDD_ARM_1V0";
>+ regulator-min-microvolt = <800000>;
>+ regulator-max-microvolt = <1500000>;
>+ regulator-always-on;
>+ regulator-boot-on;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+ };
>+
>+ buck3_reg: BUCK3 {
>+ regulator-name = "VDD_INT_1V0";
>+ regulator-min-microvolt = <800000>;
>+ regulator-max-microvolt = <1400000>;
>+ regulator-always-on;
>+ regulator-boot-on;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+ };
>+
>+ buck4_reg: BUCK4 {
>+ regulator-name = "VDD_G3D_1V0";
>+ regulator-min-microvolt = <700000>;
>+ regulator-max-microvolt = <1400000>;
>+ regulator-always-on;
>+ regulator-boot-on;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+ };
>+
>+ buck5_reg: BUCK5 {
>+ regulator-name = "VDD_MEM_1V2";
>+ regulator-min-microvolt = <1200000>;
>+ regulator-max-microvolt = <1200000>;
>+ regulator-always-on;
>+ regulator-boot-on;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+
>+ };
>+
>+ buck6_reg: BUCK6 {
>+ regulator-name = "VDD_KFC_1V0";
>+ regulator-min-microvolt = <800000>;
>+ regulator-max-microvolt = <1500000>;
>+ regulator-always-on;
>+ regulator-boot-on;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+ };
>+
>+ buck7_reg: BUCK7 {
>+ regulator-name = "VIN_LLDO_1V4";
>+ regulator-min-microvolt = <1200000>;
>+ regulator-max-microvolt = <1500000>;
>+ regulator-always-on;
>+ };
>+
>+ buck8_reg: BUCK8 {
>+ regulator-name = "VIN_MLDO_2V0";
>+ regulator-min-microvolt = <1800000>;
>+ regulator-max-microvolt = <2100000>;
>+ regulator-always-on;
>+ };
>+
>+ buck9_reg: BUCK9 {
>+ regulator-name = "VIN_HLDO_3V5";
>+ regulator-min-microvolt = <3000000>;
>+ regulator-max-microvolt = <3500000>;
>+ regulator-always-on;
>+ };
>+
>+ buck10_reg: BUCK10 {
>+ regulator-name = "VDD_CAM_ISP_1V0";
>+ regulator-min-microvolt = <750000>;
>+ regulator-max-microvolt = <3550000>;
>+ };
>+
>+ ldo1_reg: LDO1 {
>+ regulator-name = "VDD_ALIVE_1.0V";
>+ regulator-min-microvolt = <1000000>;
>+ regulator-max-microvolt = <1000000>;
>+ regulator-always-on;
>+ };
>+
>+ ldo2_reg: LDO2 {
>+ regulator-name = "VDD_APIO_1V8";
>+ regulator-min-microvolt = <1800000>;
>+ regulator-max-microvolt = <1800000>;
>+ regulator-always-on;
>+ regulator-boot-on;
>+
>+ regulator-state-mem {
>+ regulator-on-in-suspend;
>+ };
>+ };
>+
>+ ldo3_reg: LDO3 {
>+ regulator-name = "VDD_APIO_MMC01_1V8";
>+ regulator-min-microvolt = <1800000>;
>+ regulator-max-microvolt = <1800000>;
>+ regulator-always-on;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+ };
>+
>+ ldo4_reg: LDO4 {
>+ regulator-name = "VDD_ADC_1V8";
>+ regulator-min-microvolt = <1800000>;
>+ regulator-max-microvolt = <1800000>;
>+ regulator-always-on;
>+ regulator-boot-on;
>+
>+ regulator-state-mem {
>+ regulator-on-in-suspend;
>+ };
>+ };
>+
>+ ldo5_reg: LDO5 {
>+ /* Unused */
>+ regulator-name = "VDD_LDO5";
>+ regulator-min-microvolt = <1800000>;
>+ regulator-max-microvolt = <1800000>;
>+ };
>+
>+ ldo6_reg: LDO6 {
>+ regulator-name = "VDD_MIPI_1V0";
>+ regulator-min-microvolt = <1000000>;
>+ regulator-max-microvolt = <1000000>;
>+ regulator-always-on;
>+ regulator-boot-on;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+ };
>+
>+ ldo7_reg: LDO7 {
>+ regulator-name =
>"VDD_MIPI_PLL_ABB1_18V";
>+ regulator-min-microvolt = <1800000>;
>+ regulator-max-microvolt = <1800000>;
>+ regulator-always-on;
>+ regulator-boot-on;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+ };
>+
>+ ldo8_reg: LDO8 {
>+ /* Unused */
>+ regulator-name = "VDD_LDO8";
>+ regulator-min-microvolt = <1800000>;
>+ regulator-max-microvolt = <1800000>;
>+ };
>+
>+ ldo9_reg: LDO9 {
>+ regulator-name = "VDD_UOTG_3V0";
>+ regulator-min-microvolt = <3000000>;
>+ regulator-max-microvolt = <3000000>;
>+ regulator-always-on;
>+ regulator-boot-on;
>+
>+ regulator-state-mem {
>+ regulator-on-in-suspend;
>+ };
>+ };
>+
>+ ldo10_reg: LDO10 {
>+ regulator-name = "VDDQ_PRE_1V8";
>+ regulator-min-microvolt = <1800000>;
>+ regulator-max-microvolt = <1800000>;
>+ regulator-always-on;
>+ regulator-boot-on;
>+
>+ regulator-state-mem {
>+ regulator-on-in-suspend;
>+ };
>+ };
>+
>+ ldo11_reg: LDO11 {
>+ regulator-name = "VDD_HSIC_1V0";
>+ regulator-min-microvolt = <1000000>;
>+ regulator-max-microvolt = <1000000>;
>+ regulator-always-on;
>+ regulator-boot-on;
>+
>+ regulator-state-mem {
>+ regulator-on-in-suspend;
>+ };
>+ };
>+
>+ ldo12_reg: LDO12 {
>+ regulator-name = "VDD_HSIC_1V8";
>+ regulator-min-microvolt = <1800000>;
>+ regulator-max-microvolt = <1800000>;
>+ regulator-always-on;
>+ regulator-boot-on;
>+
>+ regulator-state-mem {
>+ regulator-on-in-suspend;
>+ };
>+ };
>+
>+ ldo13_reg: LDO13 {
>+ regulator-name = "VDD_APIO_MMC2_2V8";
>+ regulator-min-microvolt = <1800000>;
>+ regulator-max-microvolt = <2800000>;
>+ regulator-boot-on;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+ };
>+
>+ ldo14_reg: LDO14 {
>+ regulator-name = "VDD_MOTOR_3V0";
>+ regulator-min-microvolt = <3000000>;
>+ regulator-max-microvolt = <3000000>;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+ };
>+
>+ ldo15_reg: LDO15 {
>+ regulator-name = "VDD_LDO15";
>+ /*
>+ * LDO15 varies between devices and is
>+ * specified in the device dts
>+ */
>+ };
>+
>+ ldo16_reg: LDO16 {
>+ regulator-name = "VDD_AP_2V8";
>+ regulator-min-microvolt = <2800000>;
>+ regulator-max-microvolt = <2800000>;
>+ regulator-always-on;
>+ regulator-boot-on;
>+
>+ regulator-state-mem {
>+ regulator-on-in-suspend;
>+ };
>+ };
>+
>+ ldo17_reg: LDO17 {
>+ regulator-name = "VDD_LDO17";
>+ /*
>+ * LDO17 varies between devices and is
>+ * specified in the device dts
>+ */
>+ };
>+
>+ ldo18_reg: LDO18 {
>+ /* Unused */
>+ regulator-name = "VDD_LDO18";
>+ regulator-min-microvolt = <1800000>;
>+ regulator-max-microvolt = <1800000>;
>+ };
>+
>+
Nit: remove extra line here
Not sure if you need to re-spin the patch or may be Krzysztof will fix this
will applying
Rest looks fine.
Reviewed-by: Alim Akhtar <[email protected]>
>+ ldo19_reg: LDO19 {
>+ regulator-name = "VDD_VTF_2V8";
>+ regulator-min-microvolt = <2800000>;
>+ regulator-max-microvolt = <2800000>;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+ };
>+
>+ ldo20_reg: LDO20 {
>+ regulator-name = "VDD_CAM1_CAM_1V8";
>+ regulator-min-microvolt = <1800000>;
>+ regulator-max-microvolt = <1800000>;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+ };
>+
>+ ldo21_reg: LDO21 {
>+ regulator-name = "VDD_CAM_IO_1V8";
>+ regulator-min-microvolt = <1800000>;
>+ regulator-max-microvolt = <1800000>;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+ };
>+
>+ ldo22_reg: LDO22 {
>+ regulator-name =
>"VDD_CAM0_S_CORE_1V1";
>+ regulator-min-microvolt = <1050000>;
>+ regulator-max-microvolt = <1200000>;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+ };
>+
>+ ldo23_reg: LDO23 {
>+ regulator-name = "VDD_MIFS_1V1";
>+ regulator-min-microvolt = <800000>;
>+ regulator-max-microvolt = <1100000>;
>+ regulator-always-on;
>+
>+ regulator-state-mem {
>+ regulator-on-in-suspend;
>+ };
>+ };
>+
>+ ldo24_reg: LDO24 {
>+ regulator-name = "VDD_TSP_3V3";
>+ regulator-min-microvolt = <3300000>;
>+ regulator-max-microvolt = <3300000>;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+ };
>+
>+ ldo25_reg: LDO25 {
>+ /* Unused */
>+ regulator-name = "VDD_LDO25";
>+ regulator-min-microvolt = <800000>;
>+ regulator-max-microvolt = <3950000>;
>+ };
>+
>+ ldo26_reg: LDO26 {
>+ regulator-name = "VDD_CAM0_AF_2V8";
>+ regulator-min-microvolt = <2800000>;
>+ regulator-max-microvolt = <2800000>;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+ };
>+
>+ ldo27_reg: LDO27 {
>+ regulator-name = "VDD_G3DS_1V0";
>+ regulator-min-microvolt = <800000>;
>+ regulator-max-microvolt = <1000000>;
>+ regulator-always-on;
>+
>+ regulator-state-mem {
>+ regulator-on-in-suspend;
>+ };
>+ };
>+
>+ ldo28_reg: LDO28 {
>+ regulator-name = "VDD_LDO28";
>+ /*
>+ * LDO28 varies between devices and is
>+ * specified in the device dts
>+ */
>+ };
>+
>+ ldo29_reg: LDO29 {
>+ regulator-name = "VDD_LDO29";
>+ /*
>+ * LDO29 varies between devices and is
>+ * specified in the device dts
>+ */
>+ };
>+
>+ ldo30_reg: LDO30 {
>+ regulator-name = "VDD_TOUCH_1V8";
>+ regulator-min-microvolt = <1900000>;
>+ regulator-max-microvolt = <1900000>;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+ };
>+
>+ ldo31_reg: LDO31 {
>+ regulator-name = "VDD_LDO31";
>+ /*
>+ * LDO31 varies between devices and is
>+ * specified in the device dts
>+ */
>+ };
>+
>+ ldo32_reg: LDO32 {
>+ regulator-name = "VDD_LDO32";
>+ /*
>+ * LDO32 varies between devices and is
>+ * specified in the device dts
>+ */
>+ };
>+
>+ ldo33_reg: LDO33 {
>+ regulator-name = "VDD_MHL_1V8";
>+ regulator-min-microvolt = <1800000>;
>+ regulator-max-microvolt = <1800000>;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+ };
>+
>+ ldo34_reg: LDO34 {
>+ regulator-name = "VDD_MHL_3V3";
>+ regulator-min-microvolt = <3300000>;
>+ regulator-max-microvolt = <3300000>;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+ };
>+
>+ ldo35_reg: LDO35 {
>+ regulator-name = "VDD_SIL_1V2";
>+ regulator-min-microvolt = <1200000>;
>+ regulator-max-microvolt = <1200000>;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+ };
>+
>+ ldo36_reg: LDO36 {
>+ /* Unused */
>+ regulator-name = "VDD_LDO36";
>+ regulator-min-microvolt = <800000>;
>+ regulator-max-microvolt = <3950000>;
>+ };
>+
>+ ldo37_reg: LDO37 {
>+ /* Unused */
>+ regulator-name = "VDD_LDO37";
>+ regulator-min-microvolt = <800000>;
>+ regulator-max-microvolt = <3950000>;
>+ };
>+
>+ ldo38_reg: LDO38 {
>+ regulator-name = "VDD_KEY_LED_3V3";
>+ regulator-min-microvolt = <2500000>;
>+ regulator-max-microvolt = <3300000>;
>+
>+ regulator-state-mem {
>+ regulator-off-in-suspend;
>+ };
>+ };
>+ };
>+ };
>+};
>+
>+&mixer {
>+ status = "okay";
>+};
>+
>+/* Internal storage */
>+&mmc_0 {
>+ status = "okay";
>+ bus-width = <8>;
>+ cap-mmc-highspeed;
>+ card-detect-delay = <200>;
>+ mmc-hs200-1_8v;
>+ non-removable;
>+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>;
>+ pinctrl-names = "default";
>+ samsung,dw-mshc-ciu-div = <3>;
>+ samsung,dw-mshc-ddr-timing = <0 2>;
>+ samsung,dw-mshc-sdr-timing = <0 4>;
>+ vqmmc-supply = <&ldo3_reg>;
>+};
>+
>+/* External sdcard */
>+&mmc_2 {
>+ status = "okay";
>+ bus-width = <4>;
>+ cap-sd-highspeed;
>+ card-detect-delay = <200>;
>+ cd-gpios = <&gpx2 4 GPIO_ACTIVE_LOW>;
>+ pinctrl-0 = <&sd2_clk &sd2_cmd &mmc2_cd &sd2_bus1 &sd2_bus4>;
>+ pinctrl-names = "default";
>+ samsung,dw-mshc-ciu-div = <3>;
>+ samsung,dw-mshc-ddr-timing = <0 2>;
>+ samsung,dw-mshc-sdr-timing = <0 4>;
>+ sd-uhs-sdr50;
>+ vmmc-supply = <&ldo19_reg>;
>+ vqmmc-supply = <&ldo13_reg>;
>+};
>+
>+&pinctrl_0 {
>+ mmc2_cd: mmc2-cd-pins {
>+ samsung,pins = "gpx2-4";
>+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
>+ };
>+
>+ s2mps11_irq: s2mps11-irq-pins {
>+ samsung,pins = "gpx3-0";
>+ samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
>+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
>+ samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
>+ };
>+};
>+
>+&rtc {
>+ status = "okay";
>+ clocks = <&clock CLK_RTC>, <&s2mps11_osc S2MPS11_CLK_AP>;
>+ clock-names = "rtc", "rtc_src";
>+};
>+
>+&tmu_cpu0 {
>+ vtmu-supply = <&ldo10_reg>;
>+};
>+
>+&tmu_cpu1 {
>+ vtmu-supply = <&ldo10_reg>;
>+};
>+
>+&tmu_cpu2 {
>+ vtmu-supply = <&ldo10_reg>;
>+};
>+
>+&tmu_cpu3 {
>+ vtmu-supply = <&ldo10_reg>;
>+};
>+
>+&tmu_gpu {
>+ vtmu-supply = <&ldo10_reg>;
>+};
>+
>+&usbdrd_dwc3_0 {
>+ dr_mode = "peripheral";
>+};
>+
>+&usbdrd_dwc3_1 {
>+ dr_mode = "peripheral";
>+};
>+
>+&usbdrd3_0 {
>+ vdd33-supply = <&ldo9_reg>;
>+ vdd10-supply = <&ldo11_reg>;
>+};
>+
>+&usbdrd3_1 {
>+ vdd33-supply = <&ldo9_reg>;
>+ vdd10-supply = <&ldo11_reg>;
>+};
>--
>2.34.1
On Tue, 18 Jan 2022 19:57:43 +0100, Henrik Grimler wrote:
> Samsung's tablet Galaxy Tab S 10.5" (wifi) has codename Chagall WiFi
> and is one of several tablets released in 2014 based on Exynos 5420.
> This initial devicetree adds support for accessing device over USB or
> UART, and allows using a rootfs in either the internal eMMC or an
> external sdcard. 4 out of 8 CPUs are brought up when device boots,
> which is the same as on the somewhat similar board
> exynos5420-arndale-octa.
>
> [...]
Applied, thanks!
[1/3] dt-bindings: arm: samsung: document Chagall WiFi board binding
commit: 9998104515d4197d774e5384df750c6384915707
[2/3] ARM: exynos: only do SMC_CMD_CPU1BOOT call on Exynos4
commit: 534aaa1802eae339d0439feafe3c1217f5643b20
[3/3] ARM: dts: Add support for Samsung Chagall WiFi
commit: 535f7fffed880312830c72d9c593b59ec741dd8e
Best regards,
--
Krzysztof Kozlowski <[email protected]>