Ctera C200 V1 is kirkwood-based 2-Bay NAS.
Hardware:
- SoC: Marvell 88F6281-A1 ARMv5TE Processor 1.2GHz
- Ram: 512MB (4x Nanya NT5TU128M8GE-AC)
- NAND Flash: 256MB (Samsung 216 K9F2G08U0C)
- Lan: 1x GBE (Marvell 88E1116R-NNC1)
- Storage: 2x SATA HDD 3.5" Slot
- USB: 2x USB 2.0 port
- Console: Internal J3 connector (1: Vcc, 2: Rx, 3: Tx, 4: GND)
- LEDs: 13x GPIO controlled
- Buttons: 2x GPIO controlled
Signed-off-by: Pawel Dembicki <[email protected]>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/kirkwood-c200-v1.dts | 319 +++++++++++++++++++++++++
2 files changed, 320 insertions(+)
create mode 100644 arch/arm/boot/dts/kirkwood-c200-v1.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 235ad559acb2..31616f6ae173 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -281,6 +281,7 @@ dtb-$(CONFIG_ARCH_KEYSTONE) += \
dtb-$(CONFIG_MACH_KIRKWOOD) += \
kirkwood-b3.dtb \
kirkwood-blackarmor-nas220.dtb \
+ kirkwood-c200-v1.dtb \
kirkwood-cloudbox.dtb \
kirkwood-d2net.dtb \
kirkwood-db-88f6281.dtb \
diff --git a/arch/arm/boot/dts/kirkwood-c200-v1.dts b/arch/arm/boot/dts/kirkwood-c200-v1.dts
new file mode 100644
index 000000000000..902cafdedfd4
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-c200-v1.dts
@@ -0,0 +1,319 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Ctera C200 V1 Board Description
+ * Copyright 2021-2022 Pawel Dembicki <[email protected]>
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Ctera C200 V1";
+ compatible = "ctera,c200-v1", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ stdout-path = &uart0;
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&pmx_buttons>;
+ pinctrl-names = "default";
+
+ power {
+ label = "Power Button";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
+ };
+
+ reset {
+ label = "Reset Button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+ };
+
+ usb1 {
+ label = "USB1 Button";
+ linux,code = <BTN_0>;
+ gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
+ };
+
+ usb2 {
+ label = "USB2 Button";
+ linux,code = <BTN_1>;
+ gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-poweroff {
+ compatible = "gpio-poweroff";
+ pinctrl-0 = <&pmx_poweroff>;
+ pinctrl-names = "default";
+ gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&pmx_leds>;
+ pinctrl-names = "default";
+
+
+ led-0 {
+ function = LED_FUNCTION_DISK;
+ function-enumerator = <2>;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+ };
+
+ led-1 {
+ function = LED_FUNCTION_DISK;
+ function-enumerator = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
+ };
+
+ led-2 {
+ function = LED_FUNCTION_DISK;
+ function-enumerator = <2>;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
+ };
+
+ led-3 {
+ function = LED_FUNCTION_DISK;
+ function-enumerator = <1>;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
+ };
+
+ led-4 {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+ };
+
+ led-5 {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
+ };
+
+ led-6 {
+ function = LED_FUNCTION_INDICATOR;
+ color = <LED_COLOR_ID_BLUE>;
+ gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+ };
+
+
+ led-7 {
+ function = LED_FUNCTION_DISK_ERR;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+ };
+
+
+ led-8 {
+ function = LED_FUNCTION_DISK_ERR;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
+ };
+
+ led-9 {
+ function = LED_FUNCTION_USB;
+ function-enumerator = <1>;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+ };
+
+ led-10 {
+ function = LED_FUNCTION_USB;
+ function-enumerator = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "usbport";
+ trigger-sources = <&hub_port2>;
+ };
+
+ led-11 {
+ function = LED_FUNCTION_USB;
+ function-enumerator = <2>;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+ };
+
+ led-12 {
+ function = LED_FUNCTION_USB;
+ function-enumerator = <2>;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "usbport";
+ trigger-sources = <&hub_port1>;
+ };
+ };
+};
+
+ð0 {
+ status = "okay";
+};
+
+ð0port {
+ phy-handle = <ðphy9>;
+};
+
+&i2c0 {
+ status = "okay";
+
+ rtc@30 {
+ compatible = "s35390a";
+ reg = <0x30>;
+ };
+
+ lm63@4c {
+ compatible = "national,lm63";
+ reg = <0x4c>;
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy9: ethernet-phy@9 {
+ reg = <9>;
+ };
+};
+
+&nand {
+ status = "okay";
+ chip-delay = <40>;
+
+ partition@0 {
+ label = "uboot";
+ reg = <0x0000000 0x200000>;
+ };
+
+ partition@200000 {
+ label = "certificate";
+ reg = <0x0200000 0x100000>;
+ };
+
+ partition@300000 {
+ label = "preset_cfg";
+ reg = <0x0300000 0x100000>;
+ };
+
+ partition@400000 {
+ label = "dev_params";
+ reg = <0x0400000 0x100000>;
+ };
+ partition@500000 {
+ label = "active_bank";
+ reg = <0x0500000 0x0100000>;
+ };
+
+ partition@600000 {
+ label = "magic";
+ reg = <0x0600000 0x0100000>;
+ };
+
+ partition@700000 {
+ label = "bank1";
+ reg = <0x0700000 0x2800000>;
+ };
+
+ partition@2f00000 {
+ label = "bank2";
+ reg = <0x2f00000 0x2800000>;
+ };
+
+ /* 0x5700000-0x5a00000 undefined in vendor firmware */
+
+ partition@5a00000 {
+ label = "reserved";
+ reg = <0x5a00000 0x2000000>;
+ };
+
+ partition@7a00000 {
+ label = "rootfs";
+ reg = <0x7a00000 0x8600000>;
+ };
+};
+
+&pciec {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&pinctrl {
+ /* buzzer gpios are connected to two pins of buzzer
+ * leave it as is due lack of proper driver
+ */
+ pmx_buzzer: pmx-buzzer {
+ marvell,pins = "mpp12", "mpp13";
+ marvell,function = "gpio";
+ };
+
+ pmx_leds: pmx-leds {
+ marvell,pins = "mpp14", "mpp15", "mpp16", "mpp17", "mpp38",
+ "mpp39", "mpp40", "mpp42", "mpp43", "mpp44",
+ "mpp45", "mpp46", "mpp47";
+ marvell,function = "gpio";
+ };
+
+ pmx_buttons: pmx-buttons {
+ marvell,pins = "mpp28", "mpp29", "mpp48", "mpp49";
+ marvell,function = "gpio";
+ };
+
+ pmx_poweroff: pmx-poweroff {
+ marvell,pins = "mpp34";
+ marvell,function = "gpio";
+ };
+};
+
+&rtc {
+ status = "disabled";
+};
+
+&sata {
+ status = "okay";
+ nr-ports = <2>;
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&usb0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ #trigger-source-cells = <0>;
+
+ hub_port1: port@1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+
+ hub_port2: port@2 {
+ reg = <2>;
+ #trigger-source-cells = <0>;
+ };
+ };
+};
--
2.25.1
On Mon, Feb 07, 2022 at 10:20:14PM +0100, Pawel Dembicki wrote:
> Ctera C200 V1 is kirkwood-based 2-Bay NAS.
>
> Hardware:
> - SoC: Marvell 88F6281-A1 ARMv5TE Processor 1.2GHz
> - Ram: 512MB (4x Nanya NT5TU128M8GE-AC)
> - NAND Flash: 256MB (Samsung 216 K9F2G08U0C)
> - Lan: 1x GBE (Marvell 88E1116R-NNC1)
> - Storage: 2x SATA HDD 3.5" Slot
> - USB: 2x USB 2.0 port
> - Console: Internal J3 connector (1: Vcc, 2: Rx, 3: Tx, 4: GND)
> - LEDs: 13x GPIO controlled
> - Buttons: 2x GPIO controlled
>
> Signed-off-by: Pawel Dembicki <[email protected]>
Hi Pawel
It is a good idea to Cc: the mvebu maintainers, since kirkwood is part
of that.
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-0 = <&pmx_leds>;
> + pinctrl-names = "default";
> +
> +
Please avoid 2 blank lines. This happens a few times in this file.
> +&pciec {
> + status = "okay";
> +};
It would be nice to have a comment about what is on the PCIe bus. Or
is it just a socket?
> +
> +&pcie0 {
> + status = "okay";
> +};
> +
> +&pinctrl {
> + /* buzzer gpios are connected to two pins of buzzer
> + * leave it as is due lack of proper driver
> + */
> + pmx_buzzer: pmx-buzzer {
> + marvell,pins = "mpp12", "mpp13";
> + marvell,function = "gpio";
> + };
Is it possible to use "gpio-beeper"?
beeper: beeper {
/* 4KHz Piezoelectric buzzer */
compatible = "gpio-beeper";
pinctrl-0 = <&pmx_beeper>;
pinctrl-names = "default";
gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
};
Andrew