From: Tom Rix <[email protected]>
For spdx
Remove leading space, add space after //
Replacements
overriden to overridden
Calulate to Calculate
addional to additional
regulatior to regulator
devive to device
Signed-off-by: Tom Rix <[email protected]>
---
drivers/regulator/max8973-regulator.c | 2 +-
drivers/regulator/sc2731-regulator.c | 2 +-
drivers/regulator/ti-abb-regulator.c | 6 +++---
drivers/regulator/wm8350-regulator.c | 2 +-
4 files changed, 6 insertions(+), 6 deletions(-)
diff --git a/drivers/regulator/max8973-regulator.c b/drivers/regulator/max8973-regulator.c
index 80b65cb87cefd..cb7e50003f702 100644
--- a/drivers/regulator/max8973-regulator.c
+++ b/drivers/regulator/max8973-regulator.c
@@ -459,7 +459,7 @@ static int max8973_thermal_read_temp(void *data, int *temp)
return ret;
}
- /* +1 degC to trigger cool devive */
+ /* +1 degC to trigger cool device */
if (val & MAX77621_CHIPID_TJINT_S)
*temp = mchip->junction_temp_warning + 1000;
else
diff --git a/drivers/regulator/sc2731-regulator.c b/drivers/regulator/sc2731-regulator.c
index 0f21f95c8981c..71e5ceb679f4a 100644
--- a/drivers/regulator/sc2731-regulator.c
+++ b/drivers/regulator/sc2731-regulator.c
@@ -1,4 +1,4 @@
- //SPDX-License-Identifier: GPL-2.0
+// SPDX-License-Identifier: GPL-2.0
/*
* Copyright (C) 2017 Spreadtrum Communications Inc.
*/
diff --git a/drivers/regulator/ti-abb-regulator.c b/drivers/regulator/ti-abb-regulator.c
index 2931a0b89bffb..bd7b2f287250e 100644
--- a/drivers/regulator/ti-abb-regulator.c
+++ b/drivers/regulator/ti-abb-regulator.c
@@ -42,7 +42,7 @@
/**
* struct ti_abb_info - ABB information per voltage setting
* @opp_sel: one of TI_ABB macro
- * @vset: (optional) vset value that LDOVBB needs to be overriden with.
+ * @vset: (optional) vset value that LDOVBB needs to be overridden with.
*
* Array of per voltage entries organized in the same order as regulator_desc's
* volt_table list. (selector is used to index from this array)
@@ -484,7 +484,7 @@ static int ti_abb_init_timings(struct device *dev, struct ti_abb *abb)
/* Calculate cycle rate */
cycle_rate = DIV_ROUND_CLOSEST(clock_cycles * 10, clk_rate);
- /* Calulate SR2_WTCNT_VALUE */
+ /* Calculate SR2_WTCNT_VALUE */
sr2_wt_cnt_val = DIV_ROUND_CLOSEST(abb->settling_time * 10, cycle_rate);
dev_dbg(dev, "%s: Clk_rate=%ld, sr2_cnt=0x%08x\n", __func__,
@@ -688,7 +688,7 @@ MODULE_DEVICE_TABLE(of, ti_abb_of_match);
* @pdev: ABB platform device
*
* Initializes an individual ABB LDO for required Body-Bias. ABB is used to
- * addional bias supply to SoC modules for power savings or mandatory stability
+ * additional bias supply to SoC modules for power savings or mandatory stability
* configuration at certain Operating Performance Points(OPPs).
*
* Return: 0 on success or appropriate error value when fails
diff --git a/drivers/regulator/wm8350-regulator.c b/drivers/regulator/wm8350-regulator.c
index 6579bfdb0c262..b1d5aac8917de 100644
--- a/drivers/regulator/wm8350-regulator.c
+++ b/drivers/regulator/wm8350-regulator.c
@@ -1112,7 +1112,7 @@ static int wm8350_regulator_probe(struct platform_device *pdev)
if (pdev->id < WM8350_DCDC_1 || pdev->id > WM8350_ISINK_B)
return -ENODEV;
- /* do any regulatior specific init */
+ /* do any regulator specific init */
switch (pdev->id) {
case WM8350_DCDC_1:
val = wm8350_reg_read(wm8350, WM8350_DCDC1_LOW_POWER);
--
2.26.3
On Sat, Mar 05, 2022 at 08:24:38AM -0800, [email protected] wrote:
> From: Tom Rix <[email protected]>
>
> For spdx
> Remove leading space, add space after //
>
> Replacements
> overriden to overridden
> Calulate to Calculate
> addional to additional
> regulatior to regulator
> devive to device
>
> Signed-off-by: Tom Rix <[email protected]>
> ---
For wm8350:
Acked-by: Charles Keepax <[email protected]>
Thanks,
Charles
On Sat, 5 Mar 2022 08:24:38 -0800, [email protected] wrote:
> From: Tom Rix <[email protected]>
>
> For spdx
> Remove leading space, add space after //
>
> Replacements
> overriden to overridden
> Calulate to Calculate
> addional to additional
> regulatior to regulator
> devive to device
>
> [...]
Applied to
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git for-next
Thanks!
[1/1] regulator: cleanup comments
commit: bbc7ba0fa06ab4aee26969a9454ca32e4a8fcb1c
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
Thanks,
Mark