2022-04-04 06:22:50

by Frank Wunderlich

[permalink] [raw]
Subject: [PATCH v1 2/2] arm64: dts: rockchip: Add gmac1 and change network settings

From: Frank Wunderlich <[email protected]>

New Version (v1.0) of R2 pro has swapped gmacs compared to the v00.

WAN-Port is now on gmac1 (RTL8211F) and lan-ports on gmac0 with mt7531
switch.

There is already a mt7531 dsa driver in mainline, but it needs to be
modified to work for this board.

Fixes: f901aaadaa2a ("arm64: dts: rockchip: Add Bananapi R2 Pro")
Signed-off-by: Frank Wunderlich <[email protected]>
---
.../boot/dts/rockchip/rk3568-bpi-r2-pro.dts | 36 +++++++++++++++++--
1 file changed, 33 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3568-bpi-r2-pro.dts b/arch/arm64/boot/dts/rockchip/rk3568-bpi-r2-pro.dts
index a0388ff85ddf..067fe4a6b178 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-bpi-r2-pro.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-bpi-r2-pro.dts
@@ -16,6 +16,7 @@ / {

aliases {
ethernet0 = &gmac0;
+ ethernet1 = &gmac1;
mmc0 = &sdmmc0;
mmc1 = &sdhci;
};
@@ -78,7 +79,6 @@ &gmac0 {
assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>, <&cru CLK_MAC0_2TOP>;
clock_in_out = "input";
- phy-handle = <&rgmii_phy0>;
phy-mode = "rgmii";
pinctrl-names = "default";
pinctrl-0 = <&gmac0_miim
@@ -90,8 +90,38 @@ &gmac0_rgmii_clk
snps,reset-active-low;
/* Reset time is 20ms, 100ms for rtl8211f */
snps,reset-delays-us = <0 20000 100000>;
+ tx_delay = <0x4f>;
+ rx_delay = <0x0f>;
+ status = "okay";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+};
+
+&gmac1 {
+ assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
+ assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru CLK_MAC1_2TOP>;
+ clock_in_out = "output";
+ phy-handle = <&rgmii_phy1>;
+ phy-mode = "rgmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac1m1_miim
+ &gmac1m1_tx_bus2
+ &gmac1m1_rx_bus2
+ &gmac1m1_rgmii_clk
+ &gmac1m1_rgmii_bus>;
+
+ snps,reset-gpio = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>;
+ snps,reset-active-low;
+ /* Reset time is 20ms, 100ms for rtl8211f */
+ snps,reset-delays-us = <0 20000 100000>;
+
tx_delay = <0x3c>;
rx_delay = <0x2f>;
+
status = "okay";
};

@@ -315,8 +345,8 @@ &i2c5 {
status = "disabled";
};

-&mdio0 {
- rgmii_phy0: ethernet-phy@0 {
+&mdio1 {
+ rgmii_phy1: ethernet-phy@0 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <0x0>;
};
--
2.25.1