Hi Shawn and all interested,
This is small updates to the Librem 5 phone hardware descriptions we've
been using for quite some time as part of PureOS.
thanks,
martin
Angus Ainslie (1):
arm64: dts: imx8mq-librem5: add a RO firmware partition
Guido Günther (2):
arm64: dts: imx8mq-librem5: higher boost regulation current
arm64: dts: imx8mq-librem5-r4: add the correct panel
Martin Kepplinger (2):
arm64: dts: imx8mq-librem5: make the volume buttons a wakeup source
arm64: dts: imx8mq-librem5: remove description of CHG_STATUS_B
.../boot/dts/freescale/imx8mq-librem5-r4.dts | 4 ++++
arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi | 15 +++++----------
2 files changed, 9 insertions(+), 10 deletions(-)
--
2.30.2
From: Angus Ainslie <[email protected]>
This partition will hold a squashfs firmware jail. Only one read-only
partition is needed.
Signed-off-by: Angus Ainslie <[email protected]>
Signed-off-by: Martin Kepplinger <[email protected]>
---
arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi | 9 ++-------
1 file changed, 2 insertions(+), 7 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
index a0c8191bd33c..587e55aaa57b 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
@@ -325,15 +325,10 @@ partition@0 {
};
partition@30000 {
- label = "protected1";
- reg = <0x30000 0x10000>;
+ label = "firmware";
+ reg = <0x30000 0x1d0000>;
read-only;
};
-
- partition@40000 {
- label = "rw";
- reg = <0x40000 0x1C0000>;
- };
};
};
--
2.30.2
From: Guido Günther <[email protected]>
1,5A is what's used by the type-c controller on the Librem 5 board so
increase ti,boost-max-current to 1,5A too.
Signed-off-by: Guido Günther <[email protected]>
Signed-off-by: Martin Kepplinger <[email protected]>
---
arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
index b7d9edc1358b..a0c8191bd33c 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
@@ -1098,7 +1098,7 @@ bq25895: charger@6a {
ti,precharge-current = <130000>; /* uA */
ti,minimum-sys-voltage = <3700000>; /* uV */
ti,boost-voltage = <5000000>; /* uV */
- ti,boost-max-current = <500000>; /* uA */
+ ti,boost-max-current = <1500000>; /* uA */
ti,use-vinmin-threshold = <1>; /* enable VINDPM */
ti,vinmin-threshold = <3900000>; /* uV */
monitored-battery = <&bat>;
--
2.30.2
On Mon, Feb 28, 2022 at 02:12:17PM +0100, Martin Kepplinger wrote:
> Hi Shawn and all interested,
>
> This is small updates to the Librem 5 phone hardware descriptions we've
> been using for quite some time as part of PureOS.
>
> thanks,
> martin
>
> Angus Ainslie (1):
> arm64: dts: imx8mq-librem5: add a RO firmware partition
>
> Guido G?nther (2):
> arm64: dts: imx8mq-librem5: higher boost regulation current
> arm64: dts: imx8mq-librem5-r4: add the correct panel
>
> Martin Kepplinger (2):
> arm64: dts: imx8mq-librem5: make the volume buttons a wakeup source
> arm64: dts: imx8mq-librem5: remove description of CHG_STATUS_B
Applied all, thanks!