From: Alexandru Tachici <[email protected]>
The ADIN1100 is a low power single port 10BASE-T1L transceiver designed for
industrial Ethernet applications and is compliant with the IEEE 802.3cg
Ethernet standard for long reach 10 Mb/s Single Pair Ethernet.
The ADIN1100 uses Auto-Negotiation capability in accordance
with IEEE 802.3 Clause 98, providing a mechanism for
exchanging information between PHYs to allow link partners to
agree to a common mode of operation.
The concluded operating mode is the transmit amplitude mode and
master/slave preference common across the two devices.
Both device and LP advertise their ability and request for
increased transmit at:
- BASE-T1 autonegotiation advertisement register [47:32]\
Clause 45.2.7.21 of Standard 802.3
- BIT(13) - 10BASE-T1L High Level Transmit Operating Mode Ability
- BIT(12) - 10BASE-T1L High Level Transmit Operating Mode Request
For 2.4 Vpp (high level transmit) operation, both devices need
to have the High Level Transmit Operating Mode Ability bit set,
and only one of them needs to have the High Level Transmit
Operating Mode Request bit set. Otherwise 1.0 Vpp transmit level
will be used.
Settings for eth1:
Supported ports: [ TP MII ]
Supported link modes: 10baseT1L/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT1L/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT1L/Full
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 10Mb/s
Duplex: Full
Auto-negotiation: on
master-slave cfg: preferred slave
master-slave status: slave
Port: Twisted Pair
PHYAD: 0
Transceiver: external
MDI-X: Unknown
Link detected: yes
SQI: 7/7
1. Add basic support for ADIN1100.
Alexandru Ardelean (1):
net: phy: adin1100: Add initial support for ADIN1100 industrial PHY
1. Added 10baset-T1L link modes.
2. Added 10-BasetT1L registers.
3. Added Base-T1 auto-negotiation registers. For Base-T1 these
registers decide master/slave status and TX voltage of the
device and link partner.
4. Added 10BASE-T1L support in phy-c45.c. Now genphy functions will call
Base-T1 functions where registers don't match, like the auto-negotiation ones.
5. Convert MSE to SQI using a predefined table and allow user access
through ethtool.
6. DT bindings for the 2.4 Vpp transmit mode.
Alexandru Ardelean (1):
net: phy: adin1100: Add initial support for ADIN1100 industrial PHY
Alexandru Tachici (6):
ethtool: Add 10base-T1L link mode entry
net: phy: Add 10-BaseT1L registers
net: phy: Add BaseT1 auto-negotiation registers
net: phy: Add 10BASE-T1L support in phy-c45
net: phy: adin1100: Add SQI support
dt-bindings: net: phy: Add 10-baseT1L 2.4 Vpp
Changelog V4 -> V5:
- added int pma_extable; attribute to struct phy_device;
- added genphy_c45_baset1_able() function to determine base-t1 ability
- replaced constant reading of MDIO_PMA_EXTABLE and checking for MDIO_PMA_EXTABLE_BT1 in
phy-c45.c with the genphy_c45_baset1_able() call
Changelog V5 -> V6:
- in genphy_c45_read_status(): fixed unused variable warning
- rebased over 5.18
- in adin_config_aneg(): moved ret value checking out of if() else
- in adin_set_powerdown_mode(): used ternary instead of if() else
.../devicetree/bindings/net/ethernet-phy.yaml | 9 +
drivers/net/phy/Kconfig | 7 +
drivers/net/phy/Makefile | 1 +
drivers/net/phy/adin1100.c | 292 ++++++++++++++++++
drivers/net/phy/phy-c45.c | 257 ++++++++++++++-
drivers/net/phy/phy-core.c | 3 +-
drivers/net/phy/phy_device.c | 1 +
include/linux/mdio.h | 70 +++++
include/linux/phy.h | 2 +
include/uapi/linux/ethtool.h | 1 +
include/uapi/linux/mdio.h | 75 +++++
net/ethtool/common.c | 3 +
12 files changed, 715 insertions(+), 6 deletions(-)
create mode 100644 drivers/net/phy/adin1100.c
--
2.25.1
From: Alexandru Ardelean <[email protected]>
The ADIN1100 is a low power single port 10BASE-T1L transceiver designed for
industrial Ethernet applications and is compliant with the IEEE 802.3cg
Ethernet standard for long reach 10 Mb/s Single Pair Ethernet.
Signed-off-by: Alexandru Ardelean <[email protected]>
Signed-off-by: Alexandru Tachici <[email protected]>
---
drivers/net/phy/Kconfig | 7 ++
drivers/net/phy/Makefile | 1 +
drivers/net/phy/adin1100.c | 240 +++++++++++++++++++++++++++++++++++++
3 files changed, 248 insertions(+)
create mode 100644 drivers/net/phy/adin1100.c
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index ea7571a2b39b..bbbf6c07ea53 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -83,6 +83,13 @@ config ADIN_PHY
- ADIN1300 - Robust,Industrial, Low Latency 10/100/1000 Gigabit
Ethernet PHY
+config ADIN1100_PHY
+ tristate "Analog Devices Industrial Ethernet T1L PHYs"
+ help
+ Adds support for the Analog Devices Industrial T1L Ethernet PHYs.
+ Currently supports the:
+ - ADIN1100 - Robust,Industrial, Low Power 10BASE-T1L Ethernet PHY
+
config AQUANTIA_PHY
tristate "Aquantia PHYs"
help
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index b2728d00fc9a..b82651b57043 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -31,6 +31,7 @@ sfp-obj-$(CONFIG_SFP) += sfp-bus.o
obj-y += $(sfp-obj-y) $(sfp-obj-m)
obj-$(CONFIG_ADIN_PHY) += adin.o
+obj-$(CONFIG_ADIN1100_PHY) += adin1100.o
obj-$(CONFIG_AMD_PHY) += amd.o
aquantia-objs += aquantia_main.o
ifdef CONFIG_HWMON
diff --git a/drivers/net/phy/adin1100.c b/drivers/net/phy/adin1100.c
new file mode 100644
index 000000000000..f20bbef37239
--- /dev/null
+++ b/drivers/net/phy/adin1100.c
@@ -0,0 +1,240 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Driver for Analog Devices Industrial Ethernet T1L PHYs
+ *
+ * Copyright 2020 Analog Devices Inc.
+ */
+#include <linux/kernel.h>
+#include <linux/bitfield.h>
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/mii.h>
+#include <linux/phy.h>
+#include <linux/property.h>
+
+#define PHY_ID_ADIN1100 0x0283bc81
+
+#define ADIN_FORCED_MODE 0x8000
+#define ADIN_FORCED_MODE_EN BIT(0)
+
+#define ADIN_CRSM_SFT_RST 0x8810
+#define ADIN_CRSM_SFT_RST_EN BIT(0)
+
+#define ADIN_CRSM_SFT_PD_CNTRL 0x8812
+#define ADIN_CRSM_SFT_PD_CNTRL_EN BIT(0)
+
+#define ADIN_AN_PHY_INST_STATUS 0x8030
+#define ADIN_IS_CFG_SLV BIT(2)
+#define ADIN_IS_CFG_MST BIT(3)
+
+#define ADIN_CRSM_STAT 0x8818
+#define ADIN_CRSM_SFT_PD_RDY BIT(1)
+#define ADIN_CRSM_SYS_RDY BIT(0)
+
+/**
+ * struct adin_priv - ADIN PHY driver private data
+ * @tx_level_2v4_able: set if the PHY supports 2.4V TX levels (10BASE-T1L)
+ * @tx_level_2v4: set if the PHY requests 2.4V TX levels (10BASE-T1L)
+ * @tx_level_prop_present: set if the TX level is specified in DT
+ */
+struct adin_priv {
+ unsigned int tx_level_2v4_able:1;
+ unsigned int tx_level_2v4:1;
+ unsigned int tx_level_prop_present:1;
+};
+
+static int adin_read_status(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = genphy_c45_read_status(phydev);
+ if (ret)
+ return ret;
+
+ ret = phy_read_mmd(phydev, MDIO_MMD_AN, ADIN_AN_PHY_INST_STATUS);
+ if (ret < 0)
+ return ret;
+
+ if (ret & ADIN_IS_CFG_SLV)
+ phydev->master_slave_state = MASTER_SLAVE_STATE_SLAVE;
+
+ if (ret & ADIN_IS_CFG_MST)
+ phydev->master_slave_state = MASTER_SLAVE_STATE_MASTER;
+
+ return 0;
+}
+
+static int adin_config_aneg(struct phy_device *phydev)
+{
+ struct adin_priv *priv = phydev->priv;
+ int ret;
+
+ if (phydev->autoneg == AUTONEG_DISABLE) {
+ ret = genphy_c45_pma_setup_forced(phydev);
+ if (ret < 0)
+ return ret;
+
+ if (priv->tx_level_prop_present && priv->tx_level_2v4)
+ ret = phy_set_bits_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_B10L_PMA_CTRL,
+ MDIO_PMA_10T1L_CTRL_2V4_EN);
+ else
+ ret = phy_clear_bits_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_B10L_PMA_CTRL,
+ MDIO_PMA_10T1L_CTRL_2V4_EN);
+ if (ret < 0)
+ return ret;
+
+ /* Force PHY to use above configurations */
+ return phy_set_bits_mmd(phydev, MDIO_MMD_AN, ADIN_FORCED_MODE, ADIN_FORCED_MODE_EN);
+ }
+
+ ret = phy_clear_bits_mmd(phydev, MDIO_MMD_AN, ADIN_FORCED_MODE, ADIN_FORCED_MODE_EN);
+ if (ret < 0)
+ return ret;
+
+ /* Request increased transmit level from LP. */
+ if (priv->tx_level_prop_present && priv->tx_level_2v4) {
+ ret = phy_set_bits_mmd(phydev, MDIO_MMD_AN, MDIO_AN_T1_ADV_H,
+ MDIO_AN_T1_ADV_H_10L_TX_HI |
+ MDIO_AN_T1_ADV_H_10L_TX_HI_REQ);
+ if (ret < 0)
+ return ret;
+ }
+
+ /* Disable 2.4 Vpp transmit level. */
+ if ((priv->tx_level_prop_present && !priv->tx_level_2v4) || !priv->tx_level_2v4_able) {
+ ret = phy_clear_bits_mmd(phydev, MDIO_MMD_AN, MDIO_AN_T1_ADV_H,
+ MDIO_AN_T1_ADV_H_10L_TX_HI |
+ MDIO_AN_T1_ADV_H_10L_TX_HI_REQ);
+ if (ret < 0)
+ return ret;
+ }
+
+ return genphy_c45_config_aneg(phydev);
+}
+
+static int adin_set_powerdown_mode(struct phy_device *phydev, bool en)
+{
+ int ret;
+ int val;
+
+ val = en ? ADIN_CRSM_SFT_PD_CNTRL_EN : 0;
+ ret = phy_write_mmd(phydev, MDIO_MMD_VEND1,
+ ADIN_CRSM_SFT_PD_CNTRL, val);
+ if (ret < 0)
+ return ret;
+
+ return phy_read_mmd_poll_timeout(phydev, MDIO_MMD_VEND1, ADIN_CRSM_STAT, ret,
+ (ret & ADIN_CRSM_SFT_PD_RDY) == val,
+ 1000, 30000, true);
+}
+
+static int adin_suspend(struct phy_device *phydev)
+{
+ return adin_set_powerdown_mode(phydev, true);
+}
+
+static int adin_resume(struct phy_device *phydev)
+{
+ return adin_set_powerdown_mode(phydev, false);
+}
+
+static int adin_set_loopback(struct phy_device *phydev, bool enable)
+{
+ if (enable)
+ return phy_set_bits_mmd(phydev, MDIO_MMD_PCS, MDIO_PCS_10T1L_CTRL,
+ BMCR_LOOPBACK);
+
+ /* PCS loopback (according to 10BASE-T1L spec) */
+ return phy_clear_bits_mmd(phydev, MDIO_MMD_PCS, MDIO_PCS_10T1L_CTRL,
+ BMCR_LOOPBACK);
+}
+
+static int adin_soft_reset(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, ADIN_CRSM_SFT_RST, ADIN_CRSM_SFT_RST_EN);
+ if (ret < 0)
+ return ret;
+
+ return phy_read_mmd_poll_timeout(phydev, MDIO_MMD_VEND1, ADIN_CRSM_STAT, ret,
+ (ret & ADIN_CRSM_SYS_RDY),
+ 10000, 30000, true);
+}
+
+static int adin_get_features(struct phy_device *phydev)
+{
+ struct adin_priv *priv = phydev->priv;
+ struct device *dev = &phydev->mdio.dev;
+ int ret;
+ u8 val;
+
+ ret = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_PMA_10T1L_STAT);
+ if (ret < 0)
+ return ret;
+
+ /* This depends on the voltage level from the power source */
+ priv->tx_level_2v4_able = !!(ret & MDIO_PMA_10T1L_STAT_2V4_ABLE);
+
+ phydev_dbg(phydev, "PHY supports 2.4V TX level: %s\n",
+ priv->tx_level_2v4_able ? "yes" : "no");
+
+ priv->tx_level_prop_present = device_property_present(dev, "phy-10base-t1l-2.4vpp");
+ if (priv->tx_level_prop_present) {
+ ret = device_property_read_u8(dev, "phy-10base-t1l-2.4vpp", &val);
+ if (ret < 0)
+ return ret;
+
+ priv->tx_level_2v4 = val;
+ if (!priv->tx_level_2v4 && priv->tx_level_2v4_able)
+ phydev_info(phydev,
+ "PHY supports 2.4V TX level, but disabled via config\n");
+ }
+
+ linkmode_set_bit_array(phy_basic_ports_array, ARRAY_SIZE(phy_basic_ports_array),
+ phydev->supported);
+
+ return genphy_c45_pma_read_abilities(phydev);
+}
+
+static int adin_probe(struct phy_device *phydev)
+{
+ struct device *dev = &phydev->mdio.dev;
+ struct adin_priv *priv;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ phydev->priv = priv;
+
+ return 0;
+}
+
+static struct phy_driver adin_driver[] = {
+ {
+ PHY_ID_MATCH_MODEL(PHY_ID_ADIN1100),
+ .name = "ADIN1100",
+ .get_features = adin_get_features,
+ .soft_reset = adin_soft_reset,
+ .probe = adin_probe,
+ .config_aneg = adin_config_aneg,
+ .read_status = adin_read_status,
+ .set_loopback = adin_set_loopback,
+ .suspend = adin_suspend,
+ .resume = adin_resume,
+ },
+};
+
+module_phy_driver(adin_driver);
+
+static struct mdio_device_id __maybe_unused adin_tbl[] = {
+ { PHY_ID_MATCH_MODEL(PHY_ID_ADIN1100) },
+ { }
+};
+
+MODULE_DEVICE_TABLE(mdio, adin_tbl);
+MODULE_DESCRIPTION("Analog Devices Industrial Ethernet T1L PHY driver");
+MODULE_LICENSE("Dual BSD/GPL");
--
2.25.1