commit b4bdc4fbf8d0 ("soc: sunxi: Deal with the MBUS DMA offsets in a
central place") added a platform device notifier that sets the DMA
offset for all of the display engine frontend and backend devices.
The code applying the offset to DMA buffer physical addresses was then
removed from the backend driver in commit 756668ba682e ("drm/sun4i:
backend: Remove the MBUS quirks"), but the code subtracting PHYS_OFFSET
was left in the frontend driver.
As a result, the offset was applied twice in the frontend driver. This
likely went unnoticed because it only affects specific configurations
(scaling or certain pixel formats) where the frontend is used, on boards
with both one of these older SoCs and more than 1 GB of DRAM.
In addition, the references to PHYS_OFFSET prevent compiling the driver
on architectures where PHYS_OFFSET is not defined.
Fixes: b4bdc4fbf8d0 ("soc: sunxi: Deal with the MBUS DMA offsets in a central place")
Reviewed-by: Jernej Skrabec <[email protected]>
Signed-off-by: Samuel Holland <[email protected]>
---
(no changes since v1)
drivers/gpu/drm/sun4i/sun4i_frontend.c | 3 ---
1 file changed, 3 deletions(-)
diff --git a/drivers/gpu/drm/sun4i/sun4i_frontend.c b/drivers/gpu/drm/sun4i/sun4i_frontend.c
index 56ae38389db0..462fae73eae9 100644
--- a/drivers/gpu/drm/sun4i/sun4i_frontend.c
+++ b/drivers/gpu/drm/sun4i/sun4i_frontend.c
@@ -222,13 +222,11 @@ void sun4i_frontend_update_buffer(struct sun4i_frontend *frontend,
/* Set the physical address of the buffer in memory */
paddr = drm_fb_cma_get_gem_addr(fb, state, 0);
- paddr -= PHYS_OFFSET;
DRM_DEBUG_DRIVER("Setting buffer #0 address to %pad\n", &paddr);
regmap_write(frontend->regs, SUN4I_FRONTEND_BUF_ADDR0_REG, paddr);
if (fb->format->num_planes > 1) {
paddr = drm_fb_cma_get_gem_addr(fb, state, swap ? 2 : 1);
- paddr -= PHYS_OFFSET;
DRM_DEBUG_DRIVER("Setting buffer #1 address to %pad\n", &paddr);
regmap_write(frontend->regs, SUN4I_FRONTEND_BUF_ADDR1_REG,
paddr);
@@ -236,7 +234,6 @@ void sun4i_frontend_update_buffer(struct sun4i_frontend *frontend,
if (fb->format->num_planes > 2) {
paddr = drm_fb_cma_get_gem_addr(fb, state, swap ? 1 : 2);
- paddr -= PHYS_OFFSET;
DRM_DEBUG_DRIVER("Setting buffer #2 address to %pad\n", &paddr);
regmap_write(frontend->regs, SUN4I_FRONTEND_BUF_ADDR2_REG,
paddr);
--
2.35.1
On Sun, 24 Apr 2022 11:26:21 -0500, Samuel Holland wrote:
> commit b4bdc4fbf8d0 ("soc: sunxi: Deal with the MBUS DMA offsets in a
> central place") added a platform device notifier that sets the DMA
> offset for all of the display engine frontend and backend devices.
>
> The code applying the offset to DMA buffer physical addresses was then
> removed from the backend driver in commit 756668ba682e ("drm/sun4i:
> backend: Remove the MBUS quirks"), but the code subtracting PHYS_OFFSET
> was left in the frontend driver.
>
> [...]
Applied to drm/drm-misc (drm-misc-fixes).
Thanks!
Maxime