From: Sven Schwermer <[email protected]>
The MA510 modem has 3 USB configurations that are configurable via the AT
command AT+GTUSBMODE={30,31,32} which make the modem enumerate with the
following interfaces, respectively:
30: Diag + QDSS + Modem + RMNET
31: Diag + Modem + AT + ECM
32: Modem + AT + ECM
The first configuration (30) reuses u-blox R410M's VID/PID with
identical interface configuration.
A detailed description of the USB configuration for each mode follows:
+GTUSBMODE: 30
--------------
T: Bus=03 Lev=01 Prnt=01 Port=06 Cnt=04 Dev#= 19 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=05c6 ProdID=90b2 Rev= 0.00
S: Manufacturer=Fibocom MA510 Modem
S: Product=Fibocom MA510 Modem
S: SerialNumber=55e2695b
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
+GTUSBMODE: 31
--------------
T: Bus=03 Lev=01 Prnt=01 Port=06 Cnt=04 Dev#= 99 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2cb7 ProdID=0106 Rev= 0.00
S: Manufacturer=Fibocom MA510 Modem
S: Product=Fibocom MA510 Modem
S: SerialNumber=55e2695b
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
A: FirstIf#= 3 IfCount= 2 Cls=02(comm.) Sub=00 Prot=00
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=option
E: Ad=84(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=86(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
I: If#= 4 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 4 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
+GTUSBMODE: 32
--------------
T: Bus=03 Lev=01 Prnt=01 Port=06 Cnt=04 Dev#=100 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2cb7 ProdID=010a Rev= 0.00
S: Manufacturer=Fibocom MA510 Modem
S: Product=Fibocom MA510 Modem
S: SerialNumber=55e2695b
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
A: FirstIf#= 2 IfCount= 2 Cls=02(comm.) Sub=00 Prot=00
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
I: If#= 3 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 3 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Sven Schwermer <[email protected]>
---
drivers/usb/serial/option.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index e0af45e3a6f7..d9c2eaf09901 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -2117,6 +2117,8 @@ static const struct usb_device_id option_ids[] = {
.driver_info = RSVD(4) | RSVD(5) },
{ USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0105, 0xff), /* Fibocom NL678 series */
.driver_info = RSVD(6) },
+ { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0106, 0xff) }, /* Fibocom MA510 (ECM mode w/ diag intf.) */
+ { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x010a, 0xff) }, /* Fibocom MA510 (ECM mode) */
{ USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x010b, 0xff, 0xff, 0x30) }, /* Fibocom FG150 Diag */
{ USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x010b, 0xff, 0, 0) }, /* Fibocom FG150 AT */
{ USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a0, 0xff) }, /* Fibocom NL668-AM/NL652-EU (laptop MBIM) */
--
2.36.0
On Mon, Apr 25, 2022 at 03:11:22PM +0200, [email protected] wrote:
> From: Sven Schwermer <[email protected]>
>
> The MA510 modem has 3 USB configurations that are configurable via the AT
> command AT+GTUSBMODE={30,31,32} which make the modem enumerate with the
> following interfaces, respectively:
>
> 30: Diag + QDSS + Modem + RMNET
> 31: Diag + Modem + AT + ECM
> 32: Modem + AT + ECM
>
> The first configuration (30) reuses u-blox R410M's VID/PID with
> identical interface configuration.
>
> A detailed description of the USB configuration for each mode follows:
>
> +GTUSBMODE: 30
> --------------
> T: Bus=03 Lev=01 Prnt=01 Port=06 Cnt=04 Dev#= 19 Spd=480 MxCh= 0
> D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
> P: Vendor=05c6 ProdID=90b2 Rev= 0.00
> S: Manufacturer=Fibocom MA510 Modem
> S: Product=Fibocom MA510 Modem
> S: SerialNumber=55e2695b
> C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
> I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 1 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
> E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
> E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
> E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
> E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>
> +GTUSBMODE: 31
> --------------
> T: Bus=03 Lev=01 Prnt=01 Port=06 Cnt=04 Dev#= 99 Spd=480 MxCh= 0
> D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
> P: Vendor=2cb7 ProdID=0106 Rev= 0.00
> S: Manufacturer=Fibocom MA510 Modem
> S: Product=Fibocom MA510 Modem
> S: SerialNumber=55e2695b
> C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
> A: FirstIf#= 3 IfCount= 2 Cls=02(comm.) Sub=00 Prot=00
> I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
> E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=option
> E: Ad=84(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
> E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 3 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
> E: Ad=86(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
> I: If#= 4 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> I:* If#= 4 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>
> +GTUSBMODE: 32
> --------------
> T: Bus=03 Lev=01 Prnt=01 Port=06 Cnt=04 Dev#=100 Spd=480 MxCh= 0
> D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
> P: Vendor=2cb7 ProdID=010a Rev= 0.00
> S: Manufacturer=Fibocom MA510 Modem
> S: Product=Fibocom MA510 Modem
> S: SerialNumber=55e2695b
> C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
> A: FirstIf#= 2 IfCount= 2 Cls=02(comm.) Sub=00 Prot=00
> I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
> E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=option
> E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
> E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 2 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
> E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
> I: If#= 3 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> I:* If#= 3 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>
> Signed-off-by: Sven Schwermer <[email protected]>
> ---
> drivers/usb/serial/option.c | 2 ++
> 1 file changed, 2 insertions(+)
>
> diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
> index e0af45e3a6f7..d9c2eaf09901 100644
> --- a/drivers/usb/serial/option.c
> +++ b/drivers/usb/serial/option.c
> @@ -2117,6 +2117,8 @@ static const struct usb_device_id option_ids[] = {
> .driver_info = RSVD(4) | RSVD(5) },
> { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0105, 0xff), /* Fibocom NL678 series */
> .driver_info = RSVD(6) },
> + { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0106, 0xff) }, /* Fibocom MA510 (ECM mode w/ diag intf.) */
> + { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x010a, 0xff) }, /* Fibocom MA510 (ECM mode) */
> { USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x010b, 0xff, 0xff, 0x30) }, /* Fibocom FG150 Diag */
> { USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x010b, 0xff, 0, 0) }, /* Fibocom FG150 AT */
> { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a0, 0xff) }, /* Fibocom NL668-AM/NL652-EU (laptop MBIM) */
> --
> 2.36.0
>
Hi,
This is the friendly patch-bot of Greg Kroah-Hartman. You have sent him
a patch that has triggered this response. He used to manually respond
to these common problems, but in order to save his sanity (he kept
writing the same thing over and over, yet to different people), I was
created. Hopefully you will not take offence and will fix the problem
in your patch and resubmit it so that it can be accepted into the Linux
kernel tree.
You are receiving this message because of the following common error(s)
as indicated below:
- This looks like a new version of a previously submitted patch, but you
did not list below the --- line any changes from the previous version.
Please read the section entitled "The canonical patch format" in the
kernel file, Documentation/SubmittingPatches for what needs to be done
here to properly describe this.
If you wish to discuss this problem further, or you have questions about
how to resolve this issue, please feel free to respond to this email and
Greg will reply once he has dug out from the pending patches received
from other developers.
thanks,
greg k-h's patch email bot