Remove the unnecessary level of indentation, commonize SDC2 pins and notice
that SDCC2_CD_ON and _OFF is identical, deduplicate it!
Also, remove some unnecessary overrides and use decimal values in #-cells
Signed-off-by: Konrad Dybcio <[email protected]>
---
.../dts/qcom/msm8998-asus-novago-tp370ql.dts | 9 ---
.../boot/dts/qcom/msm8998-clamshell.dtsi | 12 ++-
arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi | 4 +-
.../dts/qcom/msm8998-sony-xperia-yoshino.dtsi | 4 +-
arch/arm64/boot/dts/qcom/msm8998.dtsi | 75 ++++++-------------
5 files changed, 33 insertions(+), 71 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/msm8998-asus-novago-tp370ql.dts b/arch/arm64/boot/dts/qcom/msm8998-asus-novago-tp370ql.dts
index e204b7050441..37f994351565 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-asus-novago-tp370ql.dts
+++ b/arch/arm64/boot/dts/qcom/msm8998-asus-novago-tp370ql.dts
@@ -37,12 +37,3 @@ keyboard@3a {
&sdhc2 {
cd-gpios = <&tlmm 95 GPIO_ACTIVE_HIGH>;
};
-
-&tlmm {
- touchpad: touchpad {
- config {
- pins = "gpio123";
- bias-pull-up;
- };
- };
-};
diff --git a/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi b/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi
index b3b352530d76..6e70c1ead5e1 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi
@@ -289,11 +289,9 @@ &remoteproc_mss {
&tlmm {
gpio-reserved-ranges = <0 4>, <81 4>;
- touchpad: touchpad {
- config {
- pins = "gpio123";
- bias-pull-up; /* pull up */
- };
+ touchpad: touchpad-pin {
+ pins = "gpio123";
+ bias-pull-up;
};
};
@@ -304,8 +302,8 @@ &sdhc2 {
vqmmc-supply = <&vreg_l13a_2p95>;
pinctrl-names = "default", "sleep";
- pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
- pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+ pinctrl-0 = <&sdc2_on &sdc2_cd>;
+ pinctrl-1 = <&sdc2_off &sdc2_cd>;
};
&ufshc {
diff --git a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
index af67c641df4e..8368af2d78e1 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
@@ -348,8 +348,8 @@ &sdhc2 {
vqmmc-supply = <&vreg_l13a_2p95>;
pinctrl-names = "default", "sleep";
- pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
- pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+ pinctrl-0 = <&sdc2_on &sdc2_cd>;
+ pinctrl-1 = <&sdc2_off &sdc2_cd>;
};
&stm {
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
index 03fa66646d47..fd65dee55626 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
@@ -580,8 +580,8 @@ &sdhc2 {
vqmmc-supply = <&vreg_l13a_2p95>;
pinctrl-names = "default", "sleep";
- pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
- pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+ pinctrl-0 = <&sdc2_on &sdc2_cd>;
+ pinctrl-1 = <&sdc2_off &sdc2_cd>;
};
&tlmm {
diff --git a/arch/arm64/boot/dts/qcom/msm8998.dtsi b/arch/arm64/boot/dts/qcom/msm8998.dtsi
index 2fda21e810c9..69cdbb104e4c 100644
--- a/arch/arm64/boot/dts/qcom/msm8998.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998.dtsi
@@ -1042,85 +1042,58 @@ tlmm: pinctrl@3400000 {
reg = <0x03400000 0xc00000>;
interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
gpio-controller;
- #gpio-cells = <0x2>;
+ #gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <0x2>;
+ #interrupt-cells = <2>;
- sdc2_clk_on: sdc2_clk_on {
- config {
+ sdc2_on: sdc2-on {
+ clk {
pins = "sdc2_clk";
- bias-disable;
drive-strength = <16>;
- };
- };
-
- sdc2_clk_off: sdc2_clk_off {
- config {
- pins = "sdc2_clk";
bias-disable;
- drive-strength = <2>;
};
- };
- sdc2_cmd_on: sdc2_cmd_on {
- config {
+ cmd {
pins = "sdc2_cmd";
- bias-pull-up;
drive-strength = <10>;
- };
- };
-
- sdc2_cmd_off: sdc2_cmd_off {
- config {
- pins = "sdc2_cmd";
bias-pull-up;
- drive-strength = <2>;
};
- };
- sdc2_data_on: sdc2_data_on {
- config {
+ data {
pins = "sdc2_data";
- bias-pull-up;
drive-strength = <10>;
+ bias-pull-up;
};
};
- sdc2_data_off: sdc2_data_off {
- config {
- pins = "sdc2_data";
- bias-pull-up;
+ sdc2_off: sdc2-off {
+ clk {
+ pins = "sdc2_clk";
drive-strength = <2>;
+ bias-disable;
};
- };
- sdc2_cd_on: sdc2_cd_on {
- mux {
- pins = "gpio95";
- function = "gpio";
+ cmd {
+ pins = "sdc2_cmd";
+ drive-strength = <2>;
+ bias-pull-up;
};
- config {
- pins = "gpio95";
- bias-pull-up;
+ data {
+ pins = "sdc2_data";
drive-strength = <2>;
+ bias-pull-up;
};
};
- sdc2_cd_off: sdc2_cd_off {
- mux {
- pins = "gpio95";
- function = "gpio";
- };
-
- config {
- pins = "gpio95";
- bias-pull-up;
- drive-strength = <2>;
- };
+ sdc2_cd: sdc2-cd {
+ pins = "gpio95";
+ function = "gpio";
+ bias-pull-up;
+ drive-strength = <2>;
};
- blsp1_uart3_on: blsp1_uart3_on {
+ blsp1_uart3_on: blsp1-uart3-on {
tx {
pins = "gpio45";
function = "blsp_uart3_a";
--
2.35.2
It's not necessary and the SoC clocks{} node doesn't use it either.
Signed-off-by: Konrad Dybcio <[email protected]>
---
arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi | 2 --
1 file changed, 2 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
index 170cd2df3e5e..28ec3e0fb201 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
@@ -21,8 +21,6 @@ / {
qcom,board-id = <8 0>;
clocks {
- compatible = "simple-bus";
-
div1_mclk: divclk1 {
compatible = "gpio-gate-clock";
pinctrl-0 = <&audio_mclk_pin>;
--
2.35.2
This is the standard way.
Signed-off-by: Konrad Dybcio <[email protected]>
---
arch/arm64/boot/dts/qcom/msm8998-fxtec-pro1.dts | 10 +++++-----
1 file changed, 5 insertions(+), 5 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/msm8998-fxtec-pro1.dts b/arch/arm64/boot/dts/qcom/msm8998-fxtec-pro1.dts
index dc5b9b274df3..33f641ca6c94 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-fxtec-pro1.dts
+++ b/arch/arm64/boot/dts/qcom/msm8998-fxtec-pro1.dts
@@ -190,7 +190,7 @@ ts_vio_vreg: ts-vio-vreg {
};
&blsp2_i2c1 {
- status = "ok";
+ status = "okay";
touchscreen@14 {
compatible = "goodix,gt9286";
@@ -206,11 +206,11 @@ touchscreen@14 {
};
&mmcc {
- status = "ok";
+ status = "okay";
};
&mmss_smmu {
- status = "ok";
+ status = "okay";
};
&pm8998_gpio {
@@ -298,11 +298,11 @@ ts_int_n: ts-int-n {
};
&ufshc {
- status = "ok";
+ status = "okay";
};
&ufsphy {
- status = "ok";
+ status = "okay";
};
&usb3_dwc3 {
--
2.35.2
Keep the nodes and includes in order, clean up unnecessary properties & nodes.
Signed-off-by: Konrad Dybcio <[email protected]>
---
.../boot/dts/qcom/msm8998-clamshell.dtsi | 118 ++++++++++--------
arch/arm64/boot/dts/qcom/pm8005.dtsi | 4 +
2 files changed, 73 insertions(+), 49 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi b/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi
index 6e70c1ead5e1..a8756bcdad3b 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi
@@ -8,13 +8,10 @@
*/
#include "msm8998.dtsi"
-#include "pm8998.dtsi"
#include "pm8005.dtsi"
+#include "pm8998.dtsi"
/ {
- chosen {
- };
-
vph_pwr: vph-pwr-regulator {
compatible = "regulator-fixed";
regulator-name = "vph_pwr";
@@ -37,6 +34,28 @@ bluetooth {
};
};
+&blsp1_uart3_on {
+ rx {
+ /delete-property/ bias-disable;
+ /*
+ * Configure a pull-up on 45 (RX). This is needed to
+ * avoid garbage data when the TX pin of the Bluetooth
+ * module is in tri-state (module powered off or not
+ * driving the signal yet).
+ */
+ bias-pull-up;
+ };
+
+ cts {
+ /delete-property/ bias-disable;
+ /*
+ * Configure a pull-down on 47 (CTS) to match the pull
+ * of the Bluetooth module.
+ */
+ bias-pull-down;
+ };
+};
+
/*
* The laptop FW does not appear to support the retention state as it is
* not advertised as enabled in ACPI, and enabling it in DT can cause boot
@@ -82,20 +101,16 @@ &pcie_phy {
status = "okay";
};
-&pm8005_lsid1 {
- pm8005-regulators {
- compatible = "qcom,pm8005-regulators";
-
- vdd_s1-supply = <&vph_pwr>;
+&pm8005_regulators {
+ vdd_s1-supply = <&vph_pwr>;
- pm8005_s1: s1 { /* VDD_GFX supply */
- regulator-min-microvolt = <524000>;
- regulator-max-microvolt = <1100000>;
- regulator-enable-ramp-delay = <500>;
+ pm8005_s1: s1 { /* VDD_GFX supply */
+ regulator-min-microvolt = <524000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-enable-ramp-delay = <500>;
- /* hack until we rig up the gpu consumer */
- regulator-always-on;
- };
+ /* hack until we rig up the gpu consumer */
+ regulator-always-on;
};
};
@@ -143,127 +158,156 @@ vreg_s3a_1p35: s3 {
regulator-min-microvolt = <1352000>;
regulator-max-microvolt = <1352000>;
};
+
vreg_s4a_1p8: s4 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-allow-set-load;
};
+
vreg_s5a_2p04: s5 {
regulator-min-microvolt = <1904000>;
regulator-max-microvolt = <2040000>;
};
+
vreg_s7a_1p025: s7 {
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1028000>;
};
+
vreg_l1a_0p875: l1 {
regulator-min-microvolt = <880000>;
regulator-max-microvolt = <880000>;
regulator-allow-set-load;
};
+
vreg_l2a_1p2: l2 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-allow-set-load;
};
+
vreg_l3a_1p0: l3 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
};
+
vreg_l5a_0p8: l5 {
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <800000>;
};
+
vreg_l6a_1p8: l6 {
regulator-min-microvolt = <1808000>;
regulator-max-microvolt = <1808000>;
};
+
vreg_l7a_1p8: l7 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-allow-set-load;
};
+
vreg_l8a_1p2: l8 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
};
+
vreg_l9a_1p8: l9 {
regulator-min-microvolt = <1808000>;
regulator-max-microvolt = <2960000>;
};
+
vreg_l10a_1p8: l10 {
regulator-min-microvolt = <1808000>;
regulator-max-microvolt = <2960000>;
};
+
vreg_l11a_1p0: l11 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
};
+
vreg_l12a_1p8: l12 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
+
vreg_l13a_2p95: l13 {
regulator-min-microvolt = <1808000>;
regulator-max-microvolt = <2960000>;
};
+
vreg_l14a_1p88: l14 {
regulator-min-microvolt = <1880000>;
regulator-max-microvolt = <1880000>;
};
+
vreg_l15a_1p8: l15 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
+
vreg_l16a_2p7: l16 {
regulator-min-microvolt = <2704000>;
regulator-max-microvolt = <2704000>;
};
+
vreg_l17a_1p3: l17 {
regulator-min-microvolt = <1304000>;
regulator-max-microvolt = <1304000>;
regulator-allow-set-load;
};
+
vreg_l18a_2p7: l18 {
regulator-min-microvolt = <2704000>;
regulator-max-microvolt = <2704000>;
};
+
vreg_l19a_3p0: l19 {
regulator-min-microvolt = <3008000>;
regulator-max-microvolt = <3008000>;
};
+
vreg_l20a_2p95: l20 {
regulator-min-microvolt = <2960000>;
regulator-max-microvolt = <2960000>;
regulator-allow-set-load;
};
+
vreg_l21a_2p95: l21 {
regulator-min-microvolt = <2960000>;
regulator-max-microvolt = <2960000>;
regulator-allow-set-load;
regulator-system-load = <800000>;
};
+
vreg_l22a_2p85: l22 {
regulator-min-microvolt = <2864000>;
regulator-max-microvolt = <2864000>;
};
+
vreg_l23a_3p3: l23 {
regulator-min-microvolt = <3312000>;
regulator-max-microvolt = <3312000>;
};
+
vreg_l24a_3p075: l24 {
regulator-min-microvolt = <3088000>;
regulator-max-microvolt = <3088000>;
};
+
vreg_l25a_3p3: l25 {
regulator-min-microvolt = <3104000>;
regulator-max-microvolt = <3312000>;
regulator-allow-set-load;
};
+
vreg_l26a_1p2: l26 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
};
+
vreg_l28_3p0: l28 {
regulator-min-microvolt = <3008000>;
regulator-max-microvolt = <3008000>;
@@ -278,7 +322,6 @@ vreg_lvs2a_1p8: lvs2 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
-
};
};
@@ -286,15 +329,6 @@ &remoteproc_mss {
status = "okay";
};
-&tlmm {
- gpio-reserved-ranges = <0 4>, <81 4>;
-
- touchpad: touchpad-pin {
- pins = "gpio123";
- bias-pull-up;
- };
-};
-
&sdhc2 {
status = "okay";
@@ -306,6 +340,15 @@ &sdhc2 {
pinctrl-1 = <&sdc2_off &sdc2_cd>;
};
+&tlmm {
+ gpio-reserved-ranges = <0 4>, <81 4>;
+
+ touchpad: touchpad-pin {
+ pins = "gpio123";
+ bias-pull-up;
+ };
+};
+
&ufshc {
status = "okay";
};
@@ -339,26 +382,3 @@ &wifi {
vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
};
-
-/* PINCTRL - board-specific pinctrl */
-&blsp1_uart3_on {
- rx {
- /delete-property/ bias-disable;
- /*
- * Configure a pull-up on 45 (RX). This is needed to
- * avoid garbage data when the TX pin of the Bluetooth
- * module is in tri-state (module powered off or not
- * driving the signal yet).
- */
- bias-pull-up;
- };
-
- cts {
- /delete-property/ bias-disable;
- /*
- * Configure a pull-down on 47 (CTS) to match the pull
- * of the Bluetooth module.
- */
- bias-pull-down;
- };
-};
diff --git a/arch/arm64/boot/dts/qcom/pm8005.dtsi b/arch/arm64/boot/dts/qcom/pm8005.dtsi
index 3f97607d8baa..50fb6c753bf8 100644
--- a/arch/arm64/boot/dts/qcom/pm8005.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8005.dtsi
@@ -28,5 +28,9 @@ pm8005_lsid1: pmic@5 {
reg = <0x5 SPMI_USID>;
#address-cells = <1>;
#size-cells = <0>;
+
+ pm8005_regulators: regulators {
+ compatible = "qcom,pm8005-regulators";
+ };
};
};
--
2.35.2
Add some newlines, reorder some properties, remove some indentation to make
it more coherent.
Signed-off-by: Konrad Dybcio <[email protected]>
---
.../boot/dts/qcom/msm8998-oneplus-common.dtsi | 45 +++++++++++++++----
1 file changed, 36 insertions(+), 9 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi b/arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi
index 5c4454da6bca..501771068938 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi
@@ -11,9 +11,9 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
#include "msm8998.dtsi"
+#include "pm8005.dtsi"
#include "pm8998.dtsi"
#include "pmi8998.dtsi"
-#include "pm8005.dtsi"
/ {
/* Required for bootloader to select correct board */
@@ -241,13 +241,11 @@ pm8005_s1: s1 {
&pm8998_gpio {
vol_keys_default: vol-keys-default {
- pinconf {
- pins = "gpio5", "gpio6";
- function = "normal";
- bias-pull-up;
- input-enable;
- qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
- };
+ pins = "gpio5", "gpio6";
+ function = "normal";
+ bias-pull-up;
+ input-enable;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
};
};
@@ -295,91 +293,113 @@ vreg_s3a_1p35: s3 {
regulator-min-microvolt = <1352000>;
regulator-max-microvolt = <1352000>;
};
+
vreg_s4a_1p8: s4 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-allow-set-load;
};
+
vreg_s5a_2p04: s5 {
regulator-min-microvolt = <1904000>;
regulator-max-microvolt = <2040000>;
};
+
vreg_s7a_1p025: s7 {
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1028000>;
};
+
vreg_l1a_0p875: l1 {
regulator-min-microvolt = <880000>;
regulator-max-microvolt = <880000>;
};
+
vreg_l2a_1p2: l2 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
};
+
vreg_l3a_1p0: l3 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
};
+
vreg_l5a_0p8: l5 {
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <800000>;
};
+
vreg_l6a_1p8: l6 {
regulator-min-microvolt = <1808000>;
regulator-max-microvolt = <1808000>;
};
+
vreg_l7a_1p8: l7 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
+
vreg_l8a_1p2: l8 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
};
+
vreg_l9a_1p8: l9 {
regulator-min-microvolt = <1808000>;
regulator-max-microvolt = <2960000>;
};
+
vreg_l10a_1p8: l10 {
regulator-min-microvolt = <1808000>;
regulator-max-microvolt = <2960000>;
};
+
vreg_l11a_1p0: l11 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
};
+
vreg_l12a_1p8: l12 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
+
vreg_l13a_2p95: l13 {
regulator-min-microvolt = <1808000>;
regulator-max-microvolt = <2960000>;
};
+
vreg_l14a_1p88: l14 {
regulator-min-microvolt = <1880000>;
regulator-max-microvolt = <1880000>;
};
+
vreg_l15a_1p8: l15 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
+
vreg_l16a_2p7: l16 {
regulator-min-microvolt = <2704000>;
regulator-max-microvolt = <2704000>;
};
+
vreg_l17a_1p3: l17 {
regulator-min-microvolt = <1304000>;
regulator-max-microvolt = <1304000>;
};
+
vreg_l18a_2p7: l18 {
regulator-min-microvolt = <2704000>;
regulator-max-microvolt = <2704000>;
};
+
vreg_l19a_3p0: l19 {
regulator-min-microvolt = <3008000>;
regulator-max-microvolt = <3008000>;
};
+
vreg_l20a_2p95: l20 {
regulator-min-microvolt = <2960000>;
regulator-max-microvolt = <2960000>;
@@ -388,34 +408,41 @@ vreg_l20a_2p95: l20 {
vreg_l21a_2p95: l21 {
regulator-min-microvolt = <2960000>;
regulator-max-microvolt = <2960000>;
- regulator-allow-set-load;
regulator-system-load = <800000>;
+ regulator-allow-set-load;
};
+
vreg_l22a_2p85: l22 {
regulator-min-microvolt = <2864000>;
regulator-max-microvolt = <2864000>;
};
+
vreg_l23a_3p3: l23 {
regulator-min-microvolt = <3312000>;
regulator-max-microvolt = <3312000>;
};
+
vreg_l24a_3p075: l24 {
regulator-min-microvolt = <3088000>;
regulator-max-microvolt = <3088000>;
};
+
vreg_l25a_3p3: l25 {
regulator-min-microvolt = <3104000>;
regulator-max-microvolt = <3312000>;
};
+
vreg_l26a_1p2: l26 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-allow-set-load;
};
+
vreg_l28_3p0: l28 {
regulator-min-microvolt = <3008000>;
regulator-max-microvolt = <3008000>;
};
+
vreg_lvs1a_1p8: lvs1 { };
vreg_lvs2a_1p8: lvs2 { };
};
--
2.35.2
On Sat, 30 Apr 2022 18:23:39 +0200, Konrad Dybcio wrote:
> Remove the unnecessary level of indentation, commonize SDC2 pins and notice
> that SDCC2_CD_ON and _OFF is identical, deduplicate it!
>
> Also, remove some unnecessary overrides and use decimal values in #-cells
>
>
Applied, thanks!
[01/14] arm64: dts: qcom: msm8998*: Fix TLMM and pin nodes
commit: 12541f687e4994774cbb4158e5fe3ecd6c639bdf
[02/14] arm64: dts: qcom: msm8998-clamshell: Clean up the DT
commit: ce383e80782e9b416d5022dc692fc80306358372
[03/14] arm64: dts: qcom: msm8998-laptops: Clean up DTs
commit: 16901ba567d789557b90871e23504a2118c35216
[04/14] arm64: dts: qcom: msm8998-yoshino-lilac: Disable LVS1
commit: 4efbec42c050e9e59171822a3829c9a364e88611
[05/14] arm64: dts: qcom: msm8998-yoshino: Add USB extcon
commit: 6dad36ebe1cb219615ead56692cea816d144c645
[06/14] arm64: dts: qcom: msm8998-yoshino: Remove simple-bus compatible from clocks{}
commit: 016928c052a75bef4ef66d844f0000058429e18c
[07/14] arm64: dts: qcom: msm8998-yoshino/oneplus: Use pm8005_regulators label
commit: b448501c2e770aad1c09abadec2045c35eb08f36
[08/14] arm64: dts: qcom: msm8998-oneplus: Apply style fixes
commit: bc0e82fbb25b32b5c69bef017ebd3e79b85883d4
[09/14] arm64: dts: qcom: msm8998-fxtec: Use "okay" instead of "ok"
commit: 20bba6b73264e7a7f1743676d7942e25d3a2131d
[10/14] arm64: dts: qcom: msm8998*: Keep MMCC & MMSS_SMMU enabled by default
commit: 392b73cb816094348abb7e3ff1288b5786b4ee16
[11/14] arm64: dts: qcom: msm8998-oneplus: Add clocks & GDSC to simplefb
commit: d582c02012d2a07251339bf0762223dbc6bb2955
[12/14] arm64: dts: qcom: msm8998*: Clean up #includes
commit: 5d393f14d4de41ff30ccad78129d96606eca827c
[13/14] arm64: dts: qcom: msm8998-fxtec: Decouple from 8998 MTP
commit: d0eaf4122c9eb6a7536bf1a607c0570ca82daa99
[14/14] arm64: dts: qcom: msm8998-mtp: Merge and fix up the DT
commit: 3ae6156e2f414f0ba2bf860e4173bbd366d5e101
Best regards,
--
Bjorn Andersson <[email protected]>